六方相W03纳米带的制备与表征

以Na2WO4、K2SO4和H2C2O4为原料,采用两步水热合成法制备了六方相W03纳米带。首先,在探索pH值、K2SO4加入量、反应温度和时间以及表面活性剂等因素对WO3纳米带的前驱物钨酸盐形貌的影响后,给出了前驱物钨酸盐纳米带的合成条件,并讨论了纳米带的形成机理;然后,在180℃的水热条件下对前驱物再处理48h获得六方相WO3纳米带。测试结果表明,WO3纳米带的形貌保持较好,宽度在100—300nm间,长度可达数微米,沿纳米带长轴方向为[001]方向。     

甲醛诱导合成WO3粉体与光致变色性质研究

采用甲醛有机诱导在水热条件下制备了形貌新颖的WO3粉体, 使用XRD, SEM, TEM, BET等手段进行结构和形貌表征, 并利用测色计对所制备的样品进行光致变色性能测试. 结果表明, 合成的WO3粉体仍为六方相, 以甲醛为诱导剂合成的粉体是由WO3纳米立方体簇集成的大小均匀的微球团聚而成, 纳米立方体的边长为20～50 nm, 簇集形成的微球直径为500～800 nm, 这种特殊的形貌有利于光生质子的产生和传输, 从而提高了合成的WO3粉体的光致变色性能.     

正丙醇诱导合成WO3粉体与光致变色性质

采用正丙醇为有机诱导剂, 在水热条件下制备了形貌新颖的WO3粉体, 使用XRD, SEM和TEM等手段进行了结构和形貌表征, 并用紫外-可见(UV-Vis)光谱仪及测色计测试了光致变色性能. 结果表明, 正丙醇诱导合成的WO3粉体仍为六方相, 但形成了特殊的海胆状纳米结构, SEM和TEM测试结果表明, 海胆状WO3微球由大量的WO3纳米杆簇集形成. 该诱导产物的纳米杆簇集成的海胆状结构显著地改善了光生质子的传输过程, 提高了合成的WO3粉体的光致变色性能.     

Sb_2Te_3纳米片的水热合成与表征

在水热条件下,以乙醇胺为还原剂,实现了亚碲酸根(TeO~(2-)_3)的分步还原,并以新生成的单质Te纳米棒为碲源,原位一步法合成出六方相Sb_2Te_3纳米片.采用X射线粉末衍射仪(XRD)、场发射扫描电子显微镜(FESEM)和透射电子显微镜(TEM)等对产物的物相、形貌及组成进行了表征.结果表明,产物Sb_2Te_3为六方纳米片,厚度约为100~200 nm,直径约为0.6~1.5μm,形貌均一,分散性良好.适宜的合成条件是水/乙醇胺体积比为8∶12,180℃下反应24 h.依据部分实验结果以及单质Te和六方相Sb_2Te_3晶体结构的比较,证明了Sb_2Te_3主要以外延方式在单质Te纳米棒表面生长,且两者的晶面取向为(003)Te//(003)Sb_2Te_3,[110]Te//[110]Sb_2Te_3.     

基于插层化学的单晶氧化钨纳米片的制备、表征与形成机制

结合插层化学与湿化学方法的优点, 建立了一种高比表面积、大径厚比、易分散的二维氧化钨(WO3)纳米片单晶的制备新方法. 微米级WO3与Bi2O3在800 ℃通过固相反应生成层状化合物Bi2W2O9; 所得到的Bi2W2O9经盐酸选择性溶出[Bi2O2]层后得到质子化形式的H2W2O7·xH2O相. 以H2W2O7·xH2O为钨源, 以辛胺插层所得无机-有机混杂纳米带为前驱物, 经硝酸氧化除去前驱物中的有机组分后得到正交相WO3·H2O纳米片; 将所得到的WO3·H2O纳米片在250~ 450 ℃和空气气氛中热处理2~5 h(升温速率为2 ℃/min), 得到单斜相WO3单晶纳米片. TEM与SEM分析结果表明, 单晶WO3·H2O与WO3纳米片的形貌相似, 其大小为(200~500) nm×(200~500) nm, 厚度为10~30 nm; 所得WO3·H2O与WO3纳米片单晶的厚度方向分别为[010]和[001]. N2吸附结果表明, WO3·H2O与WO3纳米片的比表面积分别可达到250与180 m2/g.     

LaF3纳米片和棒束的选择性合成及表征

室温条件下,以简单的液相法,通过改变氟源NaBF4和K2SiF6,制得不同形貌的LaF3纳米晶(片及棒束).X射线衍射(XRD)结果显示所得的2种不同形貌的产物均为结晶良好的六方相LaF3.场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)结果表明由NaBF4制得大量均匀、厚度约为20 am的六边形纳米片....     

不同钨源对合成纳米级WO_3形貌的影响

以钨酸钠、六氯化钨作为钨源,乙二醇、尿素为辅助盐,在酸性反应体系通过水热法合成了纳米WO3,利用XRD、SEM和EDS等对产物进行了表征。结果表明:采用不同的钨源,在相同的水热体系下,对获得的纳米级WO3形貌有较大的影响。采用钨酸钠作为钨源,乙二醇作为辅助剂可获得六方相的WO3。     

ZnIn_2S_4的制备及其表面活性剂辅助的形貌控制生长

采用湿化学合成路线以巯基乙酸为包覆剂,水为溶剂制备了六方相ZnIn2S4。应用能谱分析(EDS)、X射线衍射(XRD)、透射电镜(TEM)、扫描电镜(SEM)和紫外-可见光谱对产物的组成、结构、形貌和光学性质进行了表征。结果表明,所得到的ZnIn2S4具有层状形貌。这些层状物是由ZnIn2S4纳米粒子前驱体在热处理过程中聚集生长而成的。另外,以ZnIn2S4纳米粒子前驱体为起始原料,借助表面活性剂的导向作用在固/液界面成功地实现了ZnIn2S4的形貌控制生长,得到了具有棒状、棒簇状、管簇状形貌的ZnIn2S4。根据实验结果,初步讨论了可能的表面活性剂辅助的ZnIn2S4形貌控制生长的机制。     

水热法合成CdS/ZnO核壳结构纳米微粒

以半胱氨酸镉配合物为前驱体,采用水热法合成CdS纳米微粒,并以ZnO对其进行表面修饰,形成具有核／壳结构的CdS／ZnO半导体纳米微粒,CdS纳米微粒表面经ZnO修饰后,其带边发射大大增强,透射电镜显示,110℃下反应4h所得的CdS／ZnO颗粒尺寸约为20nm,电子衍射表明其结构为六方相。     

磷酸铋纳米棒的可控合成及其光催化性能

采用水热法合成了形貌可控的磷酸铋纳米棒光催化剂,并以亚甲基蓝(MB)为探针研究了其光催化活性.利用粉末X射线衍射(XRD),透射电镜(TEM)和紫外-可见漫反射光谱(UV-VisDRS)对产物进行了表征.研究发现甘油含量、水热时间、水热温度及前驱体浓度会影响磷酸铋纳米棒的形貌及结构.甘油含量和前驱体浓度主要影响产物形貌.随着甘油含量的增加,产物的长径比先增大后减小.前驱体浓度越低,所得BiPO4纳米棒的尺寸越小,长径比越大.水热时间短时,产物结晶度差,且为六方相,时间延长后转化为单斜相.水热温度过低或过高均不利于完美晶体的形成,160°C时产物的结晶度最高.实验结果表明:BiPO4纳米棒在紫外光下具有良好的光催化性能,其光催化活性受长径比和尺寸大小影响的总体趋势是长径比越大,尺寸越小,其光催化活性越强.结晶度对BiPO4的光催化性能影响较大,结晶度越高,其光催化活性越好.单斜相BiPO4的光催化活性较六方相的强.     

WO3纳米片：基于有机-无机杂化前驱物的制备及光催化性能

以商业三氧化钨粉末做为钨源,通过合成WO_x-EDA（EDA=乙二胺）有机-无机杂化纳米带为前驱物,再加盐酸酸化,迅速得到中间产物正交型钨酸单晶纳米片。再在空气气氛下,将中间产物在管式炉中煅烧2h,最终得到单斜型三氧化钨单晶纳米片。一系列对比实验的结果表明,在由杂化纳米带转变成钨酸纳米片时,反应温度、反应时间、酸化浓度等实验参数对产物的结构和形貌有着很大的影响。通过计算,制得的三氧化钨纳米片带隙为2.48eV。对比于商业三氧化钨粉末,三氧化钨纳米片在可见光降解罗丹明B（RhB）中表现出更优越的性能。     

WO_3纳米片:基于无机-有机杂化前驱物的制备及光催化性能

以商业三氧化钨粉末做为钨源,通过合成WOx-EDA(EDA=乙二胺)无机-有机杂化纳米带为前驱物,再加盐酸酸化,迅速得到中间产物正交型钨酸单晶纳米片。再在空气气氛下,将中间产物在管式炉中煅烧2 h,最终得到单斜型三氧化钨单晶纳米片。一系列对比实验的结果表明,在由杂化纳米带转变成钨酸纳米片时,反应温度、反应时间、酸化浓度等实验参数对产物的结构和形貌有着很大的影响。通过计算,制得的三氧化钨纳米片带隙为2.48 eV。对比于商业三氧化钨粉末,三氧化钨纳米片在可见光降解罗丹明B(RhB)中表现出更优越的性能。     

水热合成MoO3纳米带的生长机理研究

以离子交换法制备的氧化钼溶胶为前驱体，在水热条件下制备了单晶MoO₃纳米带，对样品进行了XRD、SEM和TEM分析。通过考察水热反应温度和时间对产物结构和形貌的影响，结合材料热力学和动力学理论，探讨了MoO₃纳米带在水热条件下的生长机理。离子交换法制备的溶胶在水热条件下首先转变为热力学亚稳相h-MoO₃六角柱，随着温度的升高和时间的延长，h-MoO₃按照溶解-重结晶过程转变为稳定相α-MoO₃纳米带。     

Novel pseudo-morphotactic synthesis and characterization of tungsten nitride nanoplates

A novel pseudo-morphotactic transformation route was developed to synthesize polycrystalline β-W₂N nanoplates by thermally treating tungstate-based inorganic-organic hybrid nanobelts with a lamellar microstructure in an NH₃ flow. The tungstate-based hybrid nanobelts were formed in a water-in-oil-microemulsion-like “commercial H₂WO₄ powders/n-octylamine/heptane” reaction system. The as-obtained hybrid nanobelts were thermally treated in an NH₃ atmosphere at 650-800 °C for 2 h to form cubic β-W₂N nanoplates. XRD, SEM, TEM, FT-IR and TG-DTA were used to characterize the precursors and their final products. The polycrystalline β-W₂N nanoplates derived from hybrid nanobelts, with side lengths of several hundred nanometers, consist of small nanocrystals with an average grain size of 3.2 nm. The formation of β-W₂N nanoplates involved two steps: decomposing tungstate-based hybrid nanobelts into WO_y and W species and then nitridizing the active W-containing species to β-W₂N nanocrystals in an NH₃ flow. The platelike morphology of the β-W₂N nanocrystals was inherited from the precursor of tungstate-based inorganic-organic hybrid nanobelts.     

Synthesis of Tungsten Oxide Nanorods by the Controlling Precipitation Reaction: Application for Hydrogen Evolution Reaction on a WO3 Nanorods/Carbon Nanotubes Composite Film Modified Electrode

Tungsten trioxide nanorods (WO₃) were prepared by controlling the precipitation reaction of sodium tungstate dehydrates solution and hydrothermal process. The synthesized tungsten trioxide nanorods have been characterized by X‐ray diffraction (XRD), energy dispersive spectroscopy (EDS), scanning electron microscopy (SEM), cyclic voltammetry (CV) and linear sweep voltammetry (LSV). Electrochemical activity for hydrogen evolution reaction (HER) on WO₃ nanorods / carbon nanotube (WO₃/CNT) composite electrocatalyst was first studied in acid solution (0.1 M H₂SO₄) at room temperature. The overall experimental results revealed that the electrocatalytic activity for HER on WO₃/CNT is two order magnitude higher than those obtained with WO₃ nanorods and is four times than in the case of commercial WO₃ in 0.1 M H₂SO₄. On the other hand, the kinetic reaction mechanisms were discussed on WO₃/CNT electrocatalysts in acid solution for HER. However, the rate‐determining step carries through Tafel reaction on commercial WO₃, CNT, WO₃ nanorods and WO₃/CNT electrocatalysts in acidic solution was introduced.     

Cr2(WO4)3和Cr2(MoO4)3的负热膨胀特性研究

用液相反应-前驱物烧结法制备了Cr₂(WO₄)₃和Cr₂(MoO₄)₃粉体。298～1 073 K的原位粉末X射线衍射数据表明Cr₂(WO₄)₃和Cr₂(MoO₄)₃的晶胞体积随温度的升高而增大, 本征线热膨胀系数分别为(1.274±0.003)×10^-6 K^-1和(1.612±0.003)×10^-6 K^-1。用热膨胀仪研究了Cr₂(WO₄)₃和Cr₂(MoO₄)₃在静态空气中298～1 073 K范围内热膨胀行为，即开始表现为正热膨胀，随后在相转变点达到最大值，最后表现为负热膨胀，其负热膨胀系数分别为(-7.033±0.014)×10^-6 K^-1和(-9.282±0.019)×10^-6 K^-1。     

Preparation and up-conversion fluorescence of rare earth (Er or Yb/Er)-doped TiO2 nanobelts

Anatase TiO₂ nanobelts doped with rare earth (RE) ions Yb³⁺, Er³⁺ or Yb³⁺/Er³⁺ have been prepared using layered titanate nanobelts (LTO NBs) with RE ions as the precursor obtained by ion-exchange between LTO NBs and RE ions under hydrothermal process. Various measurement results demonstrate that the RE ions have doped into the lattice of TiO₂, and the Er³⁺ or Yb³⁺/Er³⁺ doped nanobelts show strong visible up-conversion (UC) fluorescence under 980 nm excitation. The UC emission intensity of LTO NBs embedded with Er³⁺ or Yb³⁺/Er³⁺ is slightly higher than that of the corresponding TiO₂ nanobelts doped with RE ions, whereas higher RE doping content leads to the decrease of UC emission intensity due to the concentration-quenching effect.     

Synthesis of Mesoporous Tungsten Trioxide with Crystalline Pore Wall at Low Hydrothermal Temperature

Well-ordered hexagonal mesoporous tungsten trioxide with crystalline pore walls were synthesized at low hydrothermal temperature by using cationic quaternary ammonium gemini surfactants as structure-directing agents and sodium tungstate dihydrate (Na₂WO₄·2H₂O) as a precursor. The effects of alkyl chain length of gemini surfactants, hydrothermal temperature and molar ratio of tungsten to gemini surfactants have been investigated in detail. The strong self-assembly ability of gemini surfactants, strong electrical interaction between gemini surfactants and tungsten trioxide, and solvent extraction strategy contributed together to the coexistence of WO₃ mesostructures and crystalline pore walls.     

Shift of chemical equilibria and transformation laws in 12-salt six-component reciprocal systems in melt

Ten six-component 12-salt systems of various types were studied: Na,K,Ca,Ba‖F,SO₄,WO₄ (type 2ABD); Na,K,Ca‖F,Cl,SO₄,WO₄ (type AC2D); Na,K,Ca,Ba‖Cl,SO₄,WO₄ (type 4A); Na,K,Ca,Ba‖F,Cl,WO₄ (type AC2D); Li,Na,K‖Cl,Br,NO₃,SO₄ (type ABCC); Na,K,Ca,Ba‖F,Cl,SO₄ (type ABCC); K,Ca,Ba‖F,Cl,SO₄,WO₄ (type ABCC); Na,K,Ba‖F,Cl,SO₄,WO₄ (type 3AD); Na,Ca,Ba‖F,Cl,SO₄,WO₄ (type 3AB); and Na,Ca,Ba‖F,Cl,SO₄,MoO₄ (type 3BC). Laws governing the shift of exchange chemical equilibrium in these systems were determined for first time. Two groups of 12-salt systems were recognized. These groups differ in the number of the most stable salts, which have the highest indices in the matrix of vertex indices, and in the topology of their basal tetrahedra (the major elements of the singular star), which are either symmetrical or asymmetrical druses. The transformation of exchange reaction stages in going from nine-salt systems to a 12-salt system was determined. In this way, we revealed a correlation between the shift of exchange chemical equilibrium and the topology of the geometric model of a 12-salt reciprocal system, as well as with the thermo-chemical relations in this system and in the nine-salt five-component reciprocal subsystems. All models completely correlate with each other and with Kurnakov’s principle.     

High ethanol sensitivity of Palladium/TiO2 nanobelt surface heterostructures dominated by enlarged surface area and nano-Schottky junctions

TiO₂ nanobelts were prepared by the hydrothermal growth method. The surface of the nanobelts was coarsened by selective acid corrosion and functionalized with Pd catalyst particles. Three nanobelt samples (TiO₂ nanobelts, surface-coarsened TiO₂ nanobelts and Pd nanoparticle/TiO₂ nanobelt surface heterostructures) were configured as gas sensors and their sensing ability was measured. Both the surface-coarsened nanobelts and the Pd nanoparticle-decorated TiO₂ nanobelts exhibited dramatically improved sensitivity to ethanol vapor. Pd nanoparticle-decorated TiO₂ nanobelts with surface heterostructures exhibited the best sensitivity, selectivity, working temperature, response/recovery time, and reproducibility. The excellent ethanol sensing performance is attributed to the large surface area and enhancement by Schottky barrier-type junctions between the Pd nanoparticles and TiO₂ nanobelts.