用于MIP-AES的气动雾化法的研究

水溶液样品经气动雾化后引入低功率微波诱导等离子体, 由于采用了新的去溶系统和分离器, 大大改进了微波诱导等离子体原子发射光谱法的光谱分析性能。详细考察了各实验参数对测定一些元素的影响。这些元素的检出限和测定精密度令人满意。     

一种新型的ICP-AES用低功率微波热雾化系统

热雾化法自问世以来 [1 ,2 ] ,就以其较高的雾化效率及传输效率受到学者们的普遍重视 .最近 Bordera等[3] 提出了一种新的热雾化系统 (该系统采用聚焦微波炉作热雾化系统中液体样品的热源 ,即微波热雾化系统 ,简称 MWTN) ,同时还考察了实验变量对雾滴粒径分布的影响 ,并预期 MWTN具有较高的雾化效率 .本文所提出的热雾化系统与 Bordera等所建立的 MWTN系统在原理上虽然相同 ,但由于采用了新的微波器件 ,所需功率大大降低 ,因此 ,是一种新的低功率 MWTN系统 .在本实验中 ,我们对酸的浓度、载气流量、样品提升量等参数对 Mg的发射强度…     

气动雾化进样时微波等离子体炬作为激发光源的性能研究

以气动雾化进样研究了微波等离子体炬（ＭＰＴ）放电作原子发射光谱法激发光源的性能，包括ＭＰＴ的获得、操作参数的影响、样品引入及其分析性能，并与微波诱导等离子体进行了比较，证明ＭＰＴ放电作激发光源有良好的分析性能．     

气动雾化进样时微波等离子体炬作为激光发源的性能研究

以气动雾化进样研究了微波等离子体矩（ＭＰＴ）放电作原子发射光谱法激光发源的性能，包括ＭＰＴ的获得、操作参数的影响、样品引入及其分析性能，并与微波诱导等离子体进行了比较，证明了ＭＰＴ放电作激发光源有良好的分析性能。     

超声雾化进样微波诱导等离子体原子发射光谱法测定痕量磷的研究

本文提出了一种测定水溶液样品中痕量磷的微波诱导等离子体原子发射光谱法(MIPAES)。样品经超声雾化并去溶后引入等离子体。考查了Ar和He MIP中磷的发射光谱特性和一些实验参数对磷发射强度的影响。用Ar和He作工作气体时,检出限分别为0.03和0.0045μg/ml,方法的相对标准偏差小于5％。     

微波技术在样品处理中的应用

综述微波技术在样品干燥、消解、萃取、雾化等方面的应用。微波技术具有效率高、速度快、易于控制、对环境无污染的特点,具有广阔的应用前景。     

等离子体原子光谱分析中溶液样品雾化进样方法的新进展

对近年来等离子体原子光谱分析中溶液样品引入方法的新进展作了综述，其中包括气动雾化法、超声雾化法、热雾化法、悬浆雾化法、高水压雾化法及电喷雾法等。文中还根据本课题组多年来的研究经验对每种方法的优缺点及其应用作了简要的介绍和评论。     

低功率微波等离子体炬原子发射光谱法的研究——超声雾化进样测定金、银、铂、铑、钯

本文提出一种测定贵金属元素的微波等离子体炬原子发射光谱法(MPTAES)。采用自制的超声雾化微量进样装置进样,以氩气为工作气体,探讨了观察高度,微波功率、体系介质、氩气流量和共存元素对被测元素发射信号的影响。选用合适的分析线和MPT光源的工作参数,其方法的检出限分别为5.8(Au)、0.5(Ag)、12(Pt)、1.6(Rh)和t 1.0ng/ml(Pd)。实际样品中金和银的测定结果是令人满意的。     

固体微波介质加热快速提取新鲜橘皮中挥发油组分

对传统微波加热模式进行了改进,以具有良好微波吸收性能的微波吸收固体介质取代传统溶剂和水,将其加入到新鲜样品的提取体系,达到快速升温的目的.将改进的微波辅助无溶剂法应用于提取新鲜植物样品中挥发油组分,并考察了3种微波吸收介质(羰基铁粉、石墨粉和活性炭粉)对提取结果的影响.结果证明:对于新鲜样品,除活性炭粉无法使用外,羰基铁粉和石墨粉均适用.在20 g微波吸收介质及85 W微波功率的加热作用下,仅需30 min即可将100 g样品中的挥发油提取完全.通过与传统微波辅助无溶剂法、微波辅助水蒸馏法和传统水蒸馏法比较,改进的微波辅助无溶剂法具有提取时间短(30 min)、耗电量小(0.43 kW · h/kg)等优点,且所得挥发油组分无明显差别.此外,还考察了烘干过程对橘皮挥发油组成的影响,发现橘皮挥发油的组成受烘干影响较大.     

微波诱导等离子体原子吸收光谱法测定Mg,Pb,Zn的研究

微波诱导等离子体(MIP)应用于原子吸收光谱法(AAS)起始于1970年,当时由于灵敏度不高,加之是在减压条件下工作,因而未能引起人们的重视。1988年,本室采用常压Ar—MIP作为AAS的原子化器,用电热进样的方法测定了Cu、Ag、Pb等元素,获得了较好的结果。Ng等人采用气功雾化的进样方法,用MIP—AAS测定了Cu、Mn、Ca等元素,其特征浓度在μg/ml水平。本文是在上述研究的基础上,改用超声雾化方法将样品引入MIP中,用水冷凝和浓H_2SO_4吸收相结合的方法去溶,研究了对Mg、Pb和Zn的测定,并用于实际样品分析,取得了较好的结果。     

用自动凯氏定氮仪测定水中氨氮

用MgO控制预蒸馏水中的pH值,以硼酸溶液为吸收液,用稀硫酸进行中和滴定,用自动凯氏定氮仪测试水中的氨氮,检测下限为1mg/L,相对标准偏差在0.32%~1.04%范围内,加标回收率为96%~104%,并将该法与纳氏试剂比色法和离子色谱法进行了比较。     

Analysis of sewage sludge and cover soil by neutron activation analysis

The Korean government reported that in 2005, 4395 tons/day of sewage sludge were generated from sewage disposal facilities in Korea and only 11.03% of it was reused. In addition, as a direct landfill of sewage sludge was forbidden from June 2003, research for a relevant disposal technique has been increasing. In this study, the aims were to analyze the collected sewage sludge samples and to evaluate the possibility for their reuse by a comparison of the elemental contents from a sewage sludge and a cover soil. Sludge samples were collected from a sewage disposal plant in Daejeon city and the cover soil was produced by a dilution of a sewage sludge with quicklime. Instrumental neutron activation analysis was employed to determine the elemental contents in the samples. Twenty seven elements were analyzed and their concentrations were compared.     

Butyl acrylate/methyl methacrylate latexes: adhesive properties

In this study, butyl acrylate/methyl methacrylate (BA/MMA) latexes of bimodal molecular weight and particle size distribution were prepared in a multi-step process by seeded conventional emulsion and seeded miniemulsion polymerization. For the conventional emulsion case, a BA/MMA batch copolymerization was conducted as a first step (seed generation) and was followed by a monomer addition step to ensure particle growth. In a third step, a BA/MMA pre-emulsified mixture was added to generate a second particle population. For the miniemulsion case, a BA/MMA copolymerization was carried out as a first step (seed generation) and was followed by a monomer addition step. The addition of a BA/MMA miniemulsion served to generate a bimodal particle size and molecular weight distribution. The final latexes were coated onto a polyethylene terephthalate carrier, dried and their performance as pressure-sensitive adhesives was evaluated using tack, peel and shear adhesion measurements. Structure-property relationships between the adhesive properties and the weight-average molecular weight and average particle size were examined. Even though the polymers obtained by miniemulsion showed better shear resistance, their shear resistance was low. There was no statistically significant difference in peel resistance of the polymers obtained by the two reactions. While a significant difference in tackiness between the two emulsion procedures was found when the adhesives were tested using the less sensitive, rolling ball test, no differences were found when they were tested using a loop tack test.     

Effects of monomer structure and imidization degree on mechanical properties and viscoelastic behavior of thermoplastic polyimide films

Two thermoplastic polyimides based on a common diamine (3,4′-ODA) were synthesized using different dianhydrides, namely ODPA and BPDA by a two step method. Molecular weight was controlled by using PA as an end capping agent. Effects of imidization degree on the mechanical properties and viscoelastic behavior of thermoplastic polyimide films were investigated. Film samples with varying degrees of imidization were characterized using FTIR, DMTA and tensile properties testing. It was found that two polyimides have different rates of imidization because of difference in monomer reactivity and molecular structure. It was observed that with an increase in imidization degree there was a decrease in thermoplastic response and a change in viscoelastic behavior from liquid-like to solid-like. With increase in imidization degree the tensile modulus and tensile strength of the films were increased, whereas elongation at break and tensile breaking energy were found to decrease after a certain imidization temperature.     

Electroanalysis of sulfonamides by flow injection system/high-performance liquid chromatography coupled with amperometric detection using boron-doped diamond electrode

Sulfonamides (SAs) were electrochemically investigated using cyclic voltammetry at a boron-doped diamond (BDD) electrode. Comparison experiments were carried out using a glassy carbon electrode. The BDD electrode provided well-resolved oxidation, irreversible cyclic voltammograms and higher current signals when compared to the glassy carbon electrode. Results obtained from using the BDD electrode in a flow injection system coupled with amperometric detection were illustrated. The optimum potential from a hydrodynamic voltammogram was found to be 1100 mV versus Ag/AgCl, which was chosen for the HPLC-amperometric system. Excellent results of linear range and detection limit were obtained. This method was also used for determination of sulfonamides in egg samples. The standard solutions of 5, 10, and 15 ppm were spiked in a real sample, and percentage of recoveries was found to be between 90.0 and 107.7.     

3,3’-偶氮双(6-氨基-1,2,4,5-四嗪)新法合成、表征与量子化学研究

自行设计了3,3’-偶氮双(6-氨基-1,2,4,5-四嗪)(DAAT)新合成路线、采用3,5-双(3,5-二甲基吡唑-1-基)-1,2,4,5-四嗪(BDT)为原料, 由文献报道的4步反应缩减为2步, 经高压氨解、高锰酸钾氧化合成了DAAT, 总收率大幅提高, 达到58.1%, 并采用元素分析、红外光谱、核磁共振光谱等进行了结构表征. 为了从分子水平探索DAAT的性能, 采用B3LYP法, 在6-31G(d,p)基组水平上对DAAT的结构进行了优化, 计算了其性能, 获得稳定的几何构型、分子轨道及键级; 在振动分析的基础上求得体系的振动频率、IR谱及不同温度下的热力学性质, 并得温度对热力学性能影响的关系式. 结果表明: DAAT分子结构中偶氮基两侧的四嗪环和氨基基本在同一个平面上, 形成一个大的共轭π键; 红外谱计算频率和强度与实验结果整体吻合较好; 热能( )、热容( )和熵( )均随温度的升高而增大.     

Remarks on the detection of phenols in airborne particulate matter

Summary Samples of suspended particulate matter collected in Duisburg were investigated for phenolic compounds. The loaded filters were extracted with dichloromethane for 10 hours in a soxhlet apparatus. The concentrated extract was resolved in cyclohexane and separated into a non polar and a polar fraction on alumina. The polar fraction was taken up in dichloromethane and steam-distilled. The distillate was extracted with ether. After the evaporation of the ether, the residue was resolved in dichloromethane and allowed to react with benzoyl chloride. After adding toluene the solution was reduced in volume and analyzed in a GC-MS system. For the separation of phenols by means of HPLC the enrichment of the phenols was performed without benzoylization. Six phenols were detected: hydroxibenzene, methylhydroxibenzene, hydroxibiphenyl, hydroxifluorene, benzylhydroxibenzene and dihydroxibiphenyl.     

Synthesis of telechelic methacrylic siloxanes with cycloaliphatic substituents groups for UV-curable applications

Methacrylic functionalized siloxanes were prepared in a two-step process. In the first step, a series of telechelic glycidyl epoxy siloxanes were prepared, substituted with either methyl, cyclopentyl, or cyclohexyl groups. In the second step, the telechelic glycidyl epoxy groups were reacted with methacrylic acid. The reaction was monitored via acid value, and when the acid value was ?10, the reaction was terminated. Characterization of the methacrylic telechelic siloxane polymers were performed using ¹H NMR, ¹³C NMR and FT-IR. The methacrylated siloxanes were formulated with a free radical photo-initiator, UV-cured, and the rate of polymerization was monitored via photo-differential calorimetry. After curing, viscoelastic properties, and oxygen-permeability were evaluated. In addition, X-ray was used to evaluate the structure of the cured films. The rate of polymerization was dependent on substituent and increased with increasing substituent size. The oxygen permeability was dependent on crosslink density, and increased with increasing substituent size. The increase in permeability, and thus free volume was supported by X-ray studies which showed an increase in d-spacing with increasing alkyl size.     

Cold fiber solid-phase microextraction device based on thermoelectric cooling of metal fiber

A new cold fiber solid-phase microextraction device was designed and constructed based on thermoelectric cooling. A three-stage thermoelectric cooler (TEC) was used for cooling a copper rod coated with a poly(dimethylsiloxane) (PDMS) hollow fiber, which served as the solid-phase microextraction (SPME) fiber. The copper rod was mounted on a commercial SPME plunger and exposed to the cold surface of the TEC, which was enclosed in a small aluminum box. A heat sink and a fan were used to dissipate the generated heat at the hot side of the TEC. By applying an appropriate dc voltage to the TEC, the upper part of the copper rod, which was in contact to the cold side of the TEC, was cooled and the hollow fiber reached a lower temperature through heat transfer. A thermocouple was embedded in the cold side of the TEC for indirect measurement of the fiber temperature. The device was applied in quantitative analysis of off-flavors in a rice sample. Hexanal, nonanal, and undecanal were chosen as three off-flavors in rice. They were identified according to their retention times and analyzed by GC-flame ionization detection instrument. Headspace extraction conditions (i.e., temperature and time) were optimized. Standard addition calibration graphs were obtained at the optimized conditions and the concentrations of the three analytes were calculated. The concentration of hexanal was also measured using a conventional solvent extraction method (697+/-143ng/g) which was comparable to that obtained from the cold fiber SPME method (644+/-8). Moreover, the cold fiber SPME resulted in better reproducibility and shorter analysis time. Cold fiber SPME with TEC device can also be used as a portable device for field sampling.     

Experimental and Theoretical Study of the Effect of Moisture on Methane Adsorption and Desorption by Activated Carbon at 273.5 K

Adsorption and desorption of methane by activated carbon (AC) at constant temperature and at various pressures were investigated. The effect of moisture was also studied. A volumetric method was used, up to 40 bar, at a temperature of 273.5 K. Results of a dry AC sample were compared with those obtained from a moist sample and two different ACs with different physical and surface properties were used. As expected, the results showed that the existence of moisture, trapped in the AC pores, could lead to a decrease in the amount of methane adsorbed and a decrease in the amount of methane delivered during desorption. To model the experimental results, a large variety of adsorption isotherms were used. The regressed parameters for the adsorption isotherms were obtained using the experimental data generated in the present study. The accuracy of the results obtained from the different adsorption isotherms was favorably compared.