Attachment of bacterial cells to carbon electrodes

Anodic stripping method was applied to analyze the process of bacterial attachment to the surface of carbon-paste electrodes (CPE). The electrode was immersed for various times in a bacterial cell suspension to allow the cells to attach to its surface. The number of bacterial cells attached to the electrode surface increased along with time. On the other hand, the current derived from the oxidation of a dye, Hoechst, which was adsorbed to the surface after attaching the bacterial cells, decreased along with time. It was considered that the current output, correlated with the amount of dye, adsorbed onto regions where no bacterial cell attached. These results indicate that the bacterial-attachment process can be analyzed by measuring the electric current derived from the dye instead of counting the number of attached cells.     

层层自组装法制备普鲁士蓝修饰电极及对过氧化氢的测定

Fe3+可与电沉积在玻碳电极表面的对氨基苯磺酸发生静电吸附作用并与[Fe(CN)6]4-形成普鲁士蓝(PB),进一步交替重复吸附Fe3+和[Fe(CN)6]4-反应,形成PB晶体.该晶体对还原过氧化氢(H2O2)具有很高的电化学活性.通过循环伏安法、交流阻抗法和计时电流法对传感器进行了电化学表征.研究了该传感器对H2O2的电催化作用,探讨了工作电位,PH值及干扰物质对响应电流的影响.结果表明,在磷酸盐缓冲溶液中(pH =5.4,0.1 mol/L),响应电流与H2O2的浓度在0.97 ～ 32.33 mmol/L范围内具有良好的线性关系,相关系数为0.9993,传感器的响应时间小于5 s,检测限为0.48 mmol/L( S/N为3).     

Influence of solvent and counter ion on complexes of 2,5-bis(2-pyridyl)-1,3,4-oxadiazole with iron (II) and (III) studied by electrospray ionization mass spectrometry

The effect of solvent and counter ion on the complexes of 2,5-bis(2-pyridyl)-1,3,4-oxadiazole (1) with Fe+2 and Fe+3 has been studied by electrospray ionization mass spectrometry (ESI/MS). As expected, upon ESI conditions the metal reduction proceeds, but it can be deduced that complexes with Fe+2 are favored over those with Fe+3. When methanol is used as solvent, the formation of complexes of stoichiometry 2:1 and 1:1 with counter ion attached (monovalent anion) is favored, for example, [1(2)+FeCl]+ ion. The use of methanol/water (1/1) as solvent favors the formation of complexes of stoichiometry 2:1 and 3:1, namely doubly charged [1(2)+Fe]+2 and [1(3)+Fe]+2 ions. The complexes containing anion of oxidative properties (ClO4-, NO3-), when the higher cone voltage is applied, yield unusual species [1n+FeOm]+ (n=1, 2; m=1, 2). The use of divalent counter ion (SO4(-2)) resulted in formation of complexes containing two iron cations, namely [1n+Fe2SO4]+2 (n=2, 3, 4) ions. These ions can be regarded as Fe-1 complexes bridged by a sulfate anion.     

微分方法在聚苯骈咪唑修饰电极溶出伏安分析研究中的应用

本文推导了聚苯骈咪唑修饰电极溶出伏安分析中电流对电位的二次方程，并以Ｆｅ（Ｃ２Ｏ４）＾２－３为研究对象，对该方程进行了实验验证，实验结果与理论相吻合。     

咔唑基四苯乙烯多功能发光材料的合成与性能

设计合成了一个以四苯乙烯为核心,四端连接长烷基链的咔唑基四苯乙烯衍生物(TPECz),该化合物具有典型的聚集诱导发光(AIE)特性.紫外光谱(UV-Vis)、荧光光谱(PL)、热重(TG)和示差扫描量热(DSC)研究表明,该化合物属于深蓝光材料、具有较好的热稳定性,并且对金属Fe3+具有很好的识别作用,有望用于金属离子检测;同时,该化合物外围的咔唑基团具有电化学活性,采用电化学聚合方法可制备其聚合物交联荧光薄膜,扫描电镜(SEM)和原子力显微镜(AFM)研究表明,该荧光薄膜表面平整,有望用于制备有机电致发光器件(OLED),可见该化合物是一种多功能材料.     

铁氰化镨修饰的电化学传感器的研制及其对半胱氨酸的测定

采用循环伏安法在PrCl3+K3Fe(CN)6溶液中于石墨电极表面电沉积铁氰化镨(PrHCF)薄膜,制备PrHCF修饰电极。对该修饰电极电化学的行为进行分析,包括扫描速度、K+浓度以及阴、阳离子对膜电极的影响。同时,以红外和XPS对膜进行了表征,IR谱图中氰基的伸缩振动峰证明了膜的存在;而XPS谱图中Fe2p1/2和Fe2p3/2能级的分裂说明了在成膜过程中Fe的价态发生变化,据此提出了可能的电聚合机理。同时,此修饰电极对半胱氨酸具有电催化氧化活性,并对其响应进行了研究。     

Estimation of environmental mobility of heavy metals using a sequential leaching of particulate material emitted from an opencast chrome mine complex

A four-stage sequential leaching procedure was applied to assess the bioavailability and environmental mobility of heavy metals (Cr, Fe, Cu, Ni and Cd) in total suspended particulate (TSP) material emitted from an opencast chrome mine complex (Kemi, Northern Finland). TSP material was collected on glass fibre filters by a high-volume sampler, and a sequential leaching procedure was used to determine the distribution of heavy metals between the water-soluble fraction (H2O), environmentally mobile fraction (CH3COONH4), the fraction bound to carbonate and oxides (HONH3Cl + CH3COOH), and the fraction bound to silicates and organic matter, that is the environmentally immobile fraction (HNO3 + HF + HCl). The sequential leaching procedure was also applied to the certified reference materials VKI (QC Loam Soil A) and PACS-2 (Marine Sediment) to evaluate the accuracy and reproducibility of the leaching procedure. The heavy metals were determined by graphite furnace atomic absorption spectrometry (GFAAS) and flame atomic absorption spectrometry (FAAS). The concentrations of metals in the water-soluble fraction (H2O) decreased in the order Fe >Cu >Cr >Ni >Cd, and in the environmentally mobile fraction (CH3COONH4) in the order Cu >Fe >Ni >Cr >Cd.     

In situ chemical reductive growth of platinum nanoparticles on indium tin oxide surfaces and their electrochemical applications

Platinum nanoparticles directly attached to indium tin oxide (PtNP/ITO) were successfully fabricated by using an in situ chemical reductive growth method. In this method, PtNPs could be grown on the ITO surface via the one-step immersion into the growth solution containing PtCl4(2-) and ascorbic acid. The attached and grown PtNPs were spherical having an agglomerated nanostructure composed of small nanoclusters. From the morphological changes depending on the growth time, which were observed with an FE-SEM, PtNPs were found to be grown via the progressive nucleation mechanism. As the characteristics of the PtNP/ITO were those of a working electrode, it was found that the charge transfer resisivity was significantly lowered due to the grown PtNPs. Hence, for a typical redox system of [Fe(CN)6]3-/[Fe(CN)6]4-, the PtNP/ITO electrode exhibited the electrochemical responses similar to those of the bulk Pt electrode. Furthermore, it was clarified that the PtNP/ITO electrode had significant electrocatalytic properties for the oxygen reduction and methanol oxidation. The present PtNPs that had the agglomerated nanostructure may be promising for a new type of electrode material.     

Gold nanoparticles attached NH2+ ion implantation-modified indium tin oxide electrode: Characterization and electrochemical studies

An NH2+ ion implantation-modified indium tin oxide film was prepared and the implantation of amino groups on the indium tin oxide substrate was verified by X-ray photoelectron spectroscopy analysis.The gold nanoparticles attached surface could be obtained by self-assembly of different sized colloidal gold nanoparticles onto the NH2+ ion implantation-modified indium tin oxide surface.By scanning electron microscopy and electrochemical techniques,the as-prepared AuNPs attached NH2+ ion implantation-modified indium tin oxide electrode was characterized and compared with bare indium tin oxide electrode.Using a [Fe(CN)6]3 /[Fe(CN)6]4 redox probe,the increasingly facile heterogeneous electron transfer kinetics resulting from the attached gold nanoparticle arrays was observed.The gold nanoparticle arrays exhibited high catalytic activity toward the electro-oxidation of nitric oxide,which could provide electroanalytical application for nitric oxide sensing.     

Fe-based phosphate nanostructures for supercapacitors

Fe-based phosphates with excellent physical and chemical features are potential electrode materials for supercapacitors.In this work,we successfully synthesized Fe-based phosphates with different dimensions,morphologies,and compositions by one-step hydrothermal method.Influence factors on the chemical composition and morphology of the as-prepared materials were explored and the energy storage performance of the as-prepared samples were tested under the traditional three electrode system.Two-dimensional(2 D) iron metaphosphate(Fe(PO_3)_3) showed the best electrochemical performance.For Fe(PO_3)_3 electrode mate rials,the layered structure can provide a larger specific surface area than the bulk structure,which is conducive to the diffusion and transport of electrolyte ions during charging-discha rging and further improve s the rate perfo rmance and cycle stability of supe rcapacito r.2 D Fe(PO_3)_3 and activated carbon were used as electrode materials to construct a 2 D Fe(PO_3)_3//AC supercapacitor.The supercapacitor showed high energy density,high power density,and excellent cycling stability,which indicates 2 D Fe(PO_3)_3 is a promising electrode material for supercapacitors.     

Comparison of the structural properties of isomorphously substituted Fe in mordenite zeolites prepared by different methods

Fe was introduced in mordenite zeolite by means of ion exchange either in solid or in liquid state. The iron loading (50--200 wt%), iron precursor (FeSO4.7H2O and FeCl3), and mordenite starting material (NH4M, HM, and NaM) were varied during the exchange processes. The Fe species were characterized by N2 adsorption measurements as well as by XRD and M?ssbauer spectroscopies. The Fe-mordenite samples prepared by liquid-state ion exchange attained remarkable Fe dispersion and surface areas higher than those of the parent. It was found that Fe3+ ions, which substituted the framework Al and accordingly occupied tetrahedral sites, were decreased with Fe loadings with concomitant increase in Fe3+-occupied octahedral sites. The latter sites disappeared at 20 K to provoke the superparamagnetic alpha-Fe2O3 in different particles size. The acid leaching (0.1 M HCl, 333 K, 3 h) of the samples showed the disappearance of the most highly distorted extra-framework Fe3+ species, providing an indication of their presence on the external surface. On the other hand, a hematite phase was detected in the solid-state ion exchange of FeCl3 with either HM or NH4M at the loading of 100% Fe. More correlations between M?ssbauer data on one hand and XRD and texturing properties on the other hand were evaluated and discussed.     

Application of cell-based biosensors for the detection of bacterial elicitor flagellin

Cell-based biosensors, bioelectronic portable devices containing plant living cells have been used for monitoring some physiological changes induced by pathogen-derived signal molecules called flagellin. The screen-printed electrodes have been adapted for preparation of biosensors. The proton-sensitive thick films have been printed using composite bulk modified with edition of RuO(2). Obtained disposable electrodes were made possible to measure the pH change with well sensitivity and reproducibility. Tobacco cells attached to the electrode surface, cell-based biosensor, can be used for the detection of flagellin, the virulence factor of bacterial pathogen. We culture tobacco cells on the surface of such electrotransducer for several weeks and monitor of potential of cells under flagellin stimulation. The detection of the electrochemical proton gradient across the plasma membrane serves as the analytical signal. The electrode response depended upon H(+) concentration in extracellular solution. It can be conveniently observed on the surfaces of biosensors. Suitable stability and the good response time of constructed biosensors were observed. Future development of these cell-based biosensors could draw advances in selective monitoring of microbial pathogens and other physiologically active components. Moreover, this new method is much faster compared with the traditional microbial testing.     

硫酸溶液中电化学改性石墨电极对Fe3+/Fe2+的电催化性能与准电容特性

通过循环伏安(CV)、恒电流充放电和电化学阻抗谱(EIS)等测试方法,研究了电化学改性石墨电极对硫酸溶液中Fe3+/Fe2+的电催化性能与准电容特性.结果表明:由于电化学改性石墨电极表面存在大量的含氧活性官能团,使其对Fe3+/Fe2+的氧化还原反应具有极高的电催化性能,并具有可逆反应过程特征.在含有0.5mo·lL-1Fe3++0.5mo·lL-1Fe2+的2.0mo·lL-1H2SO4溶液中,其表观面积比电容是不含铁离子硫酸溶液的1.808倍,达到2.157F·cm-2;同时,铁离子浓度的增大也能够进一步提高其电容量.Fe3+/Fe2+电对的加入增加了充放电时间,有效提高了电化学电容器(EC)的电容存储容量和高功率特性.电化学阻抗谱测试同样证实体系具有明显的电容特性.因此,可以利用电化学改性石墨电极表面的含氧活性官能团和溶液中Fe3+/Fe2+的氧化还原特性来共同储存和释放能量.     

Control of the surface charges of Au-Ag nanorods: selective detection of iron in the presence of poly(sodium 4-styrenesulfonate)

In this article, we report a simple approach for selectively sensing Fe2+ ions using CTAB-stabilized Au-Ag nanorods (CTAB-Au-Ag NRs) in the presence of poly(sodium 4-styrenesulfonate) (PSS). The prepared CTAB-Au-Ag NRs exhibit an intense longitudinal surface plasmon resonance absorption (>10(9) M(-1) cm(-1) at 827 nm) in the near-infrared region. As a result of attractive electrostatic interactions between PSS and CTAB, agglomeration of the CTAB-Au-Ag NRs induces a change in the absorption at 827 nm. From zeta potential measurements, we found that the degree of agglomeration was highly dependent on the surface charge density of the CTAB-Au-Ag NRs. Because Fe2+ (Fe3+) ions selectively interact with PSS, the degree of agglomeration-and, thus, the change in absorption at 827 nm-is dependent on the concentration of Fe2+ (Fe3+) ions. To improve the selectivity of the present sensing system, Fe3+ ions were reduced to Fe2+ ions in the presence of ascorbic acid prior to analysis. The concentrations of CTAB-Au-Ag NRs and PSS are both important parameters in determining the sensitivity and selectivity of the present approach toward sensing Fe2+ ions. Under the optimum conditions [34 pM CTAB-Au-Ag NRs, (5 x 10(-6))% PSS, pH 7.2], the limit of detection for Fe2+ ions at a signal-to-noise ratio of 3 was 1.0 microM. We applied this nanosensor system to the determination of Fe2+ in ferritin and in aqueous environmental samples; this approach has the advantages of simplicity, accuracy, and precision (the relative standard deviation from five runs with each sample was below 3%).     

Determination of Hg on poly(vinylferrocenium) (PVF)-modified platinum electrode

A new surface based on poly(vinylferrocenium) (PVF⁺)-modified platinum electrode was developed for determination of Hg²⁺ ions in aqueous solutions. The polymer was electrodeposited on platinum electrode by constant potential electrolysis as PVF⁺ClO₄⁻. Cl⁻ ions were then attached to the polymer matrix by anion exchange and the modified electrode was dipped into Hg²⁺ solution. Hg²⁺ was preconcentrated at the polymer matrix by adsorption and also complexation reaction with Cl⁻. Detection of Hg²⁺ was carried out by differential pulse anodic stripping voltammetry (DPASV) after reduction of Hg²⁺. Mercury ions as low as 5 × 10⁻¹⁰ M could be detected with the prepared electrode and the relative standard deviation was calculated as 6.35% at 1 × 10⁻⁶ M concentration (n = 6). Interferences of Ag⁺, Pb²⁺ and Fe³⁺ ions were also studied at two different concentration ratios with respect to Hg²⁺. The developed electrode was applied to the determination of Hg²⁺ in water samples.     

内场致发射电极的电化学行为

在N-Si和P-Si半导体上用化学沉积法制备了内场致发射电极并研究了它们的电化学行为。从分解电势Ⅰ～Ⅴ曲线可知,这种电极可在低于1.23V下分解水;对Fe~(3+)/Fe~(2+)体系的循环伏安图,其峰电流为铂电极的8倍多。     

A novel ion selective membrane potentiometric sensor for direct determination of Fe(III) in the presence of Fe(II)

A new PVC membrane potentiometric sensor that is highly selective to Fe(III) ions was prepared by using 2-[(2-hydroxy-1-propenyl-buta-1,3-dienylimino)-methyl]-4-p-tolylazo-phenol [HPDTP] as a suitable carrier. The electrode exhibits a linear response for iron(III) ions over a wide concentration range (3.5 × 10⁻⁶ to 4.0 × 10⁻²) with a super Nernstian slope of 28.5 (±0.5) per decade. The electrode can be used in the pH range from 4.5 to 6.5. The proposed sensor shows fairly a good discriminating ability towards Fe³⁺ ion in comparison to some hard and soft metals such as Fe²⁺, Cd²⁺, Cu²⁺, Al³⁺ and Ca²⁺. It has a response time of <15 s and can be used for at least 2 months without any measurable divergence in response characteristics. The electrode was used in the direct determination of Fe³⁺ in aqueous samples and as an indicator electrode in potentiometric titration of Fe(III) ions.     

Neutral bidentate organophosphorus compounds as novel ionophores for potentiometric membrane sensors for barium(II)

Bis(diarylphosphine oxide) naphthalene compounds are used as novel ionophores in plasticized poly(vinyl chloride) matrix membrane sensors for barium ions. The most favorable sensor was 1,2-bis(diethylphenylphosphine oxide)naphthalene containing potassium tetrakis(4-chlorophenyl)borate as lipophilic salt and o-nitrophenyloctyl ether as plasticizer for ion-selective electrode membrane construction. The electrode showed excellent properties. It gave a linear response with a Nernstian slope of 30 mV per decade within the concentration range 10(-1)-10(-5) mol L(-1) BaCl2. The electrode exhibits a high selectivity towards Ba2+ with respect to Li+, Na+, K+, Rb+, Cs+, NH4+, Ag+, Mg2+, Ca2+, Sr2+, Mn2+, Fe2+, Co2+, Ni2+, Cu2+, Zn2+, Cd2+, Pb2+, Al3+, La3+, and Ce3+ ions. The electrode response was stable over a wide pH range (3-11). The lifetime of the electrode was about 2 months. It was successfully applied to the determination of Ba2+ contents in some rocks.     

Iron (III) Ion Selective Electrode Based on Dithia 12-Crown-4

An iron (III) ion selective PVC membrane electrode based on 1,7-dithia 12-crown-4 as a neutral carrier was prepared. Monovalent responses with a Nerstian slope of 56+1 mV/decade was observed for the Fe (III) ion-selective electrode within the concentration range 10^?3–10^?5 M Fe (NO₃)₃. The monovalent responses may be attributed to the formation of Fe (OH)₂⁺ or Fe (OH)₂(H₂O)⁺₄ species in aqueous solutions and the absorption of these ions into the PVC electrode membrane. The electrode exhibited good selectivity for Fe (III) in comparison with various alkali, alkali-earth and some heavy metal ions. The effects of the composition of the membrame, addition of STPB (sodium tetraphenyl borate), the concentration of internal solution of the electrode and anions in the test solutions were discussed.     

Application of liquid chromatography-atmospheric pressure chemical ionization mass spectrometry to the differentiation of stereoisomeric diterpenoid alkaloids

High-performance liquid chromatography-atmospheric pressure chemical ionization mass spectrometry (HPLC-APCI-MS) was successfully applied to seven stereoisomeric diterpenoid alkaloids at position 1 or 12. Comparison of the breakdown curves, observed by changing the potential difference between the first electrode and the second electrode of the APCI ion source, revealed stereochemical dependence of different fragmentations. The APCI spectra of alkaloids were predominantly the [M+H]+ ion and the major fragment ion, corresponding to the [M+H-H2O]+ ion or the [M+H-CH3COOH]+ ion, and comparison of the APCI spectra showed that the abundance of fragment ions was significantly higher for C-1 beta-form alkaloids than for C-1 alpha-form alkaloids, and for C-12 beta-form alkaloids than for C-12 alpha-form alkaloids. The characteristic fragment ions were formed due to the loss of an acetic acid or a water molecule at position 12. The fragmentation mechanisms depending on the stereochemistry of the precursor ion could be discerned by recording the spectra in a deuterated solvent system of 0.05 M ammonium acetate in D2O-acetonitrile-tetrahydrofuran. Loss of CH3COOD or D2O from the precursor ion gave the fragment ion. This result indicated that the proton of protonation was included in the leaving acetic acid and water molecule, respectively. The peak intensity ratio for R=[M+H]+/[M+ H-H2O]+ + [M + H-CH3COOH] + manifested the stereochemical differentiation of alkaloids at position 1 or 12.