Protein microarrays enhanced performance using nanobeads arraying and polymer coating

A nanosize material composed of 330 nm glass beads coated with a copolymer of N,N-dimethylacrylamide (DMA), N,N-acryloyloxysuccinimide (NAS) and [3-(methacryloyl-oxy)propyl]trimethoxysilane (MAPS) was developed to improve the protein immobilization on biochips. The developed material, bearing rabbit-IgG proteins, was arrayed as 150 μm spots trapped at the surface of a poly(dimethylsiloxane) elastomer (PDMS), and compared to copoly(DMA-NAS-MAPS)-coated glass slides and latex beads based biochips. Evidences were made through scanning electron microscopy that the newly developed material based microarray exhibited surface irregularities at the submicron level leading to high specific area.The combination of such large immobilization area with the highly efficient protein immobilization of the copoly(DMA-NAS-MAPS) polymer, enabled the achievement of microarrays exhibiting good performances both in pure media and complex samples (human sera). Indeed, high specific/non-specific signal ratio was found using this optimized immobilization procedure.Chemiluminescent detection of anti-rabbit-IgG was obtained through peroxidase labeled antibodies in the 5 μg/l to 10 mg/l range. Application of the developed system to real samples was achieved for the detection of rheumatoid factor (RF) through a capture assay. Interesting results were obtained, with a RF detection over the 5.3-485 IU/ml range and without measurable matrix effect or non-specific signal.     

Poly(urethaneimides) (PUIs) containing tertiary amine groups as precursors for original PUI cationomers

This paper details the synthesis and characterisation of poly(urethaneimides) (PUIs) containing tertiary amine groups and obtained from a polytetramethylene oxide diol (PTMO1000), N-methyldiethanolamine (MDEA), 4,4′-methylene-bis-phenylisocyanate (MDI) and 4,4′-hexafluoroisopropylidene-bis-phthalic anhydride (6FDA). The polymers PTMO1000 (1 − x equiv.) + MDEA (x equiv.)/MDI (2 equiv.)/6FDA (1 equiv.) were obtained in high yields (>90%) through original synthesis, involving the reaction of macrodiisocyanates with an aromatic dianhydride in two steps only. A wide range of complementary techniques including two-dimensional NMR showed that the new method enabled a very good control of the polymer structure. In particular, the tertiary amine content of the PUI copolymers was easily varied over the whole composition range (x: 0 → 1), with interesting prospects for the design of a wide range of ion-containing poly(urethaneimides) by quaternising the tertiary amine groups. The PUI properties (e.g. solubility, viscosity, film-forming ability, etc.) clearly depended upon their tertiary amine content. Up to a tertiary amine content of x = 0.7 equiv., the very good film-forming character of the PUIs enabled to cast strong films suitable for permeability investigations.     

Synthesis of macroporous poly(glycidyl methacrylate) microspheres by surfactant reverse micelles swelling method

Macroporous poly(glycidyl methacrylate-ethylene dimethacrylate) [P(GMA-EDMA)] particles with pore size around 140-200 nm and poly(glycidyl methacrylate-divinylbenzene) [P(GMA-DVB)] particles with pore size of 450 nm were prepared by the surfactant reverse micelles swelling method. This method was similar with the conventional suspension polymerization, and the difference was that higher concentration of surfactant was added in the oil phase. When the oil phase containing surfactant was dispersed in aqueous phase, the surfactant reverse micelles in the oil droplets absorbed water from continuous phase. After polymerization, the large pores were formed by the absorbed water. The effects of the amount and type of surfactants, the cooperation of surfactant and diluents, and the crosslinking agent on the morphology of microspheres were investigated. This study provided a new and simple method to prepare microspheres with the pores of several hundred nanometers, which overcame the disadvantages found in the conventional preparation methods of macroporous microspheres.     

Polymerisation of vinylidene fluoride in supercritical carbon dioxide: Formation of PVDF macroporous beads

Poly(vinylidene fluoride) (PVDF) macroporous beads with diameter in the range of hundreds of micrometers were produced by batch polymerisation of vinylidene fluoride (VDF) in supercritical carbon dioxide (scCO₂) using diethyl peroxydicarbonate (DEPDC) as a free radical initiator. The rate and type of stirring were found to influence strongly the morphology of polymers, and the results indicated that the shear force was the key factor. A low shear force and a suitable monomer concentration range at 6-8 mol/l were needed for the formation of PVDF macroporous beads. Scanning electron microscopy (SEM) was employed to characterize the polymer morphology, and Brunauer-Emmett-Teller (BET) method was used to analyze the surface area of the polymer macroporous beads. In addition, polydimethylsiloxane monomethylacrylate (PDMS-ma) and poly(1H,1H,2H,2H-perfluorooctyl methacrylate) (PFOMA) were found to be able to control the size of PVDF macroporous beads. We propose that the formation of PVDF macroporous beads results from the aggregation of semi-crystalline PVDF primary particles.     

Preparation of poly(N-isopropylacrylamide)-grafted polymer monolith for hydrophobic interaction chromatography of proteins

Poly(N-isopropylacrylamide)-grafted polymer monolith has been achieved using a surface-initiated atom transfer radical polymerization grafting polymerization within the pores of poly(chloromethylstyrene-divinylbenzene) macroporous monolith contained in a 100 mm × 4.6 mm I.D. stainless steel column. The grafted-poly(N-isopropylacrylamide) on the surface of the grafted monolith that was used as chromatographic stationary phase showed a response to the variation of temperatures and/or salt concentrations. This study focus on its salt concentration responsive property and it has been revealed that the hydrophobicity of the grafted monolith can be adjusted by changing salt concentrations in the range of 0.05-2.0 mol/L. A variety of salts including sodium sulfate, ammonium sulfate and sodium chloride exhibited different effects on the alteration of hydrophobicity of the grafted monolith, and the effect of the salts was in the order of sodium sulfate > ammonium sulfate > sodium chloride. Based on this response to salt concentrations, the grafted monolith was applied in hydrophobic interaction chromatography of proteins, and the base-line separation of a six proteins mixture consisting of cytochrome c, myoglobin, ribonuclease A, bovine serum albumin, ovalbumin and thyroglobulin bovine was achieved by a salt gradient elution.     

Effect of Porogen Solubility Parameter on Structure of Chromatographic Supports with Large Pores

The macroporous microspheres were prepared through suspension polymerization based on a copolymer of glycidyl methacrylate and ethylene glycol dimethacrylate. The effect of porogen on the microspheres structure was evaluated in terms of pore size and surface area. Porogen contained dichloromethane (δ = 9.7 (cal cm^–3)^1/2) and N-octanol (δ = 10.3 (cal cm^–3)^1/2) which were correspond to a good and poor solvent, respectively. The solubility parameter of porogen was controlled in the range of 9.89–10.09 (cal cm^–3)^1/2. The pore size of microspheres increased with the increase of difference value of solubility parameter between the polymer and the porogen. On the contrary, the surface area of microspheres decreased. The anion exchange media was prepared through coupling poly(ethylene imine) in the microspheres and the proteins transport was determined by frontal analysis method. The macroporous microspheres with 257 nm pore size could still afford a high proteins capacity (45.1 mg mL^–1). These macroporous supports showed great potential in rapid separation of proteins.     

The pellicular monolith: pore-surface functionalization and surface-phase construction in macroporous polymeric materials

We report synthesis and characterization of a macroporous polymeric material containing a covalently immobilized pore-surface phase of well-defined thickness, gel-phase porosity and organic functional group content. The pore surfaces of otherwise inert macroporous (32 μm mean pore size) ultrahigh-molecular-weight polyethylene (UHMWPE) are aminated throughout using a low-pressure flowing-discharge process to enable covalent immobilization of lightly cross-linked polymer colloid particles on all pore surfaces in the monolith. Solvent swelling and chemical derivitization of the covalently immobilized polymer colloid particles produce a pore-surface gel phase of well-defined thickness, organic amine content, and gel-phase porosity. The low degree of cross-linking in the polymer colloid particles prevents dissolution of the immobilized colloid in good solvents and enables the formation of pore-surface gel phases having high gel porosity on swelling in good solvents. The pore-surface amination introduced by the flowing discharge process varies by less than 17% through 5-mm thickness of the macroporous UHMWPE material. The properties of the pore-surface gel phase also vary by less than 17% through the cross section. The pore-surface immobilized polymer colloid particles swell by a factor of 10 in water and tetrahydrofuran after derivitization with polyethylene glycol. Received: 20 November 1998 Accepted in revised form: 21 January 1999     

Studies on copolymerization of N-isopropylacrylamide with poly(ethylene glycol) methacrylate

The paper describes the preparation and characterization of cross-linked homopolymers and copolymers of N-isopropyl acrylamide (NIPAAm) with poly(ethylene glycol) methacrylate (PEGMA, M_n = 526 g/mol). Several copolymer samples were prepared by taking varying amounts of monomers i.e. NIPAAm and PEGMA in the initial feed using hydrophilic (IRGACURE-2959) and hydrophobic (DURACURE-1173) photoinitiator. In order to investigate the effect of reaction conditions, copolymers were prepared below or above the lower critical solution temperature (LCST) using water or water:ethanol (50:50) as solvent and by varying the amounts of cross-linker. Hydrogels prepared under varying reaction conditions were characterized for its swelling behaviour (using optical microscope), phase transition temperature (using DSC) and morphology (using SEM). As expected LCST increased from 35 to 39 °C as PEGMA content in copolymers increased from 1 to 20% (w/w). However, the morphology of hydrogels was found to be independent on the reaction conditions.Copolymer films having an optimum combination of swelling and performance properties were evaluated as switchable cell culture membranes. Hepatic cancer cell lines (Hep G-2) was used to study the cell growth and detachment. Cell growth and detachment were found to be dependent on the copolymer composition. Cell viability was found comparable to trypsin which also supports application of these films as cell culture membrane.     

The effect of biological and polymeric inhibitors on methane gas hydrate growth kinetics

Kinetic experiments were performed on a methane-water system in the presence of Type-I Antifreeze Proteins (AFPs) in order to elucidate their effectiveness as kinetic hydrate inhibitors, specifically their effect on the hydrate growth period. The results were compared to experiments done with a classical polymeric kinetic hydrate inhibitor, N-vinylpryrrolidone-co-N-vinylcaprolactam [poly(VP/VC)] at the same pressure, temperature and weight percent conditions. As well, a series of experiments was conducted on poly(VP/VC) to examine the effect of concentration on hydrate growth inhibition. Experiments were performed at temperatures between 275.15 and 279.15 K and pressures between 5800 and 7200 kPa. The effect of the polymer on the hydrate growth profile was examined as well as the effect of temperature and pressure on the performance of the polymer and the protein.     

肝素化聚甲基硅氧烷-聚氧乙烯接枝物的合成及其体外抗凝血性能评价

以二甲基硅油接枝端羟基聚氧乙烯（ＰＤＭＳ ｇ ＰＥＯ ＯＨ）为基材，用二环己基碳二亚胺（ＤＣＣＩ）作脱剂，研究了羟基（ＯＨ）与肝素上的羧基（—ＣＯＯＨ）之间的脱水缩合反应，制备出肝素化的抗血栓材料ＰＤＭＳ ｇ ＰＥＯ Ｈｅｐ，并对其涂覆表面的肝素含量和体外抗凝血性能进行了初步评价．实验结果表明，肝素接枝的共聚物具有优良的抗凝血性能和一定的应用前景．     

Impregnation synthesis of a novel macroporous silica-based TODGA polymeric composite and its application in the adsorption of rare earths in nitric acid solution containing diethylenetriaminepentaacetic acid

A macroporous silica-based N,N,N′,N′-tetraoctyl-3-oxapentane-1,5-diamide (TODGA) polymeric composite (TODGA/SiO₂-P) was synthesized. It was done through impregnation and immobilization of TODGA molecule into the pores of the SiO₂-P particles utilizing a vacuum sucking technique. The macroporous SiO₂-P particles were the silica-based organic/inorganic composite synthesized by immobilizing styrene-divinylbenzene copolymer inside SiO₂ through the complicated polymerization reaction. The adsorption of rare earth (RE(III)) elements onto TODGA/SiO₂-P was investigated in HNO₃ solution containing diethylenetriaminepentaacetic acid (DTPA), an acidic multi-dentate chelating agent. It was found that in the presence of 0.05 M DTPA, and H⁺ had significant effect on the TODGA/SiO₂-P adsorption due to the competition reactions of RE(III) with different species, H₄DTPA⁻ and H₂DTPA³⁻. With an increase in the concentration of from 0.115 M to 3.015 M, the adsorption of RE(III) onto TODGA/SiO₂-P increased noticeably. On the other hand, RE(III) showed strong adsorption at 0.1 M H⁺, weak adsorption at around pH 2, and no adsorption in excess of pH 2.3. In a 0.1 M H⁺-0.115 M -0.05 M DTPA solution, a change of the distribution coefficient of RE(III) onto TODGA/SiO₂-P with an increase in atomic number of RE(III) from La(III) to Lu(III) was investigated. The silica-based TODGA/SiO₂-P polymeric composite showed strong adsorption for heavy RE(III) over the light one. In a 0.01 M H⁺-1.0 M -0.05 M DTPA solution, the effect of the ratio of solid phase to liquid one on the relationship of the distribution coefficient of RE(III) with the change in atomic number of RE(III) was also studied. Based on the complicated disassociation equilibrium of DTPA, the influence of the concentrations of and H⁺ on the adsorption of TODGA/SiO₂-P for RE(III) was demonstrated. This makes the partitioning of RE(III) and MA(III) together from high level liquid waste (HLLW) by the polymeric composite TODGA/SiO₂-P promising.     

Preparation and properties of aromatic poly(amide-imide)s derived from N-[3,5-bis(3,4-dicarboxybenzamido)phenyl]phthalimide dianhydride

An imide ring-containing diamide-dianhydride, N-[3,5-bis(3,4-dicarboxybenzamido)phenyl]phthalimide dianhydride (1) was prepared by the reaction of trimellitic anhydride chloride with N-(3,5-diaminophenyl)phthalimide in a medium consisting of methylene chloride and pyridine. A series of new alternating aromatic poly(amide-imide)s having inherent viscosities of 0.26-0.37 dl/g was synthesized using a two-step poly(amic-acid) precursor method. A reference monomer, 1,3-bis(3,4-dicarboxybenzamido)benzene dianhydride (2) without the phthalimido pendant group attached to the polymer main chain was prepared in order to study the structure-property relationship. In this case, the structure effects on some properties of the resulting poly(amide-imide)s including crystallinity, solubility, thermal stability, and film flexibility could be easily clarified. A diamide-triimide (3) as a model compound was also synthesized by the reaction of new dianhydride 1 with aniline to compare the characterization data as well as to optimize the polymerization conditions. The resulting polymers were fully characterized by FT-IR, UV-visible and ¹H NMR spectroscopy. Most of the polymers showed an amorphous nature and were readily soluble in a variety of organic solvents such as N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), N-methyl-2-pyrrolidone (NMP), and pyridine. The glass-transition temperatures of these polymers were recorded between 301 and 371 °C. All polymers showed no significant weight loss below 500 °C in nitrogen, and the decomposition temperatures at 10 wt.% loss range from 506 to 543 °C. The films of the resulting poly(amide-imide)s could be cast from their NMP solutions, and the transparency and flexibility of them were investigated.     

[3+2] Dipolar cycloadditions of an unstabilised azomethine ylide under continuous flow conditions

The [3+2] dipolar cycloaddition reactions of the unstabilised azomethine ylide precursor benzyl(methoxymethyl)(trimethylsilylmethyl)amine with 12 electron-deficient alkenes in the presence of catalytic trifluoroacetic acid are examined under continuous flow conditions (20-100 °C, 10-60 min residence time). The more reactive and hazardous alkenes such as ethyl acrylate, N-methylmaleimide and (E)-2-nitrostyrene afford substituted N-benzylpyrrolidine products in 77-83% yields, whereas less reactive dipolarophiles such as (E)-crotononitrile and ethyl methacrylate give lower yields (59-63%). Under optimised conditions, the reaction with ethyl acrylate is scaled up to afford ethyl N-benzylpyrrolidine-3-carboxylate (30 g, 87%) in 1 h.     

Electrochemical and electrochromic properties of novel aromatic poly(amine-amide)s derived from N,N′-bis(4-carboxyphenyl)-N,N′-diphenyl-1,4-phenylenediamine

A series of novel triphenylamine-containing aromatic poly(amine-amide)s were prepared from the dicarboxylic acid, N,N′-bis(4-carboxyphenyl)-N,N′-diphenyl-1,4-phenylenediamine, and various diamines by direct phosphorylation polycondensation. All the poly(amine-amide)s were amorphous, soluble in a variety of organic solvents, and could be solution cast into transparent, tough, and flexible films with good mechanical properties. They had useful levels of thermal stability associated with relatively high glass-transition temperatures (195-280 °C). These polymers exhibited strong UV-Vis absorption bands at 330-346 nm and their photoluminescence showed maximum bands around 516-535 nm in NMP solution. The hole-transporting and electrochromic properties are examined by electrochemical and spectroelectrochemical methods. Cyclic voltammograms of the poly(amine-amide)s prepared by casting polymer solution onto an indium-tin oxide (ITO)-coated glass substrate exhibited two reversible oxidative redox couples at potential 0.73-0.78 V and 1.12-1.18 V, respectively vs Ag/AgCl in acetonitrile solution. All the poly(amine-amide)s exhibited excellent reversibility of electrochromic characteristics by continuous ten cyclic scans between 0.0 and 1.40 V, with a color change from original pale yellowish neutral form to the green and then to blue oxidized forms.     

Chromium retention properties of N-alkyl quaternized poly(4-vinylpyridine)

The ability of solid N-alkyl quaternized poly(4-vinylpyridine) with hexyl, octyl and decyl bromide for the retention of chromate and dichromate forms of Cr(VI) in aqueous solutions is studied. The retention of Cr(VI) was investigated by batch equilibrium procedure and this study was supported by UV-vis spectrophotometry, infrared (IR) spectroscopy and thermal analysis (glass transition temperature and thermal degradation). The retention of Cr(VI) was possible in the range of concentrations between 1 × 10⁻⁶ and 1 × 10⁻³ mol/L and it was dependent on the length of the polyelectrolyte side aliphatic chain. Thermogravimetric analysis (TGA) indicated that solid phase, (N-alkyl quaternized poly(4-vinylpyridine), with Cr(VI) (P4VPyC8-Cr(VI)) is slightly more stable than P4VPyC8 in absence of Cr(VI). Differential scanning calorimetric (DSC) measurements indicate that the segmental movements are restricted due to the presence of chromate and/or dichromate ions in the solid phase.     

An electrochemical immunosensor based on covalent immobilization of okadaic acid onto screen printed carbon electrode via diazotization-coupling reaction

In this work, an electrochemical method based on the diazonium-coupling reaction mechanism for the immobilization of okadaic acid (OA) on screen printed carbon electrode was developed. At first, 4-carboxyphenyl film was grafted by electrochemical reduction of 4-carboxyphenyl diazonium salt, followed by terminal carboxylic group activation by N-hydroxysuccinimide (NHS), N-(3-dimethylaminopropyle)-N′-ethyle-carbodiimide hydrochloride (EDC). Hexamethyldiamine was then covalently bound by one of its terminal amine group to the activated carboxylic group. The carboxyl group of okadaic acid was activated by EDC/NHS and then conjugated to the second terminal amine group on other side of the hexamethyldiamine through amide bond formation. After immobilization of OA, an indirect competitive immunoassay format was employed to detect OA. The immunosensor obtained using this novel approach allowed detection limit of 1.44 ng/L of OA, and was also validated with certified reference mussel samples.     

One-pot synthesis of supramolecular polymer containing quadruple hydrogen bonding units

A facile, efficient technique was built to synthesize a supramolecular material containing quadruple hydrogen bonding sites. The current approach presented here involves a single-step reaction between the amine of precursor, e.g. methyl isocytosine (MIC) and the epoxy group of polymer, e.g. poly(ethylene glycol diglycidyl ether) (PEG DGE, M_n = 526 g/mol, as verified using ¹H NMR and FT-IR spectroscopy. Wide angle X-ray scattering (WAXS), UV/visible spectroscopy and differential scanning calorimeter (DSC) clearly show that the product is not a simple mixture of two components, but the supramolecular polymer containing quadruple hydrogen bonding sites. Complex melt viscosities reveal that mechanical properties of the supramolecular polymer are enhanced by more than 10⁴ times compared to the pristine low molecular weight polymer, giving rise to the significant change of physical state from liquid to solid. Current approach also illustrates an advantageous route because it does not need the selective use of monofunctionalized precursor and not produce a dead, difunctionalized precursor.     

Synthesis and characterization of poly(amideimide)s containing pendent flexible alkoxy chains

A series of aromatic diacylhydrazides containing pendent flexible alkoxy chains, viz., 5-butyloxyisophthalicacid dihydrazide, 5-octyloxyisophthalicacid dihydrazide, 5-dodecyloxyisophthalicacid dihydrazide and 5-hexadecyloxyisophthalicacid dihydrazide were synthesized by the hydrazinolysis reaction of the corresponding aromatic esters with hydrazine hydrate. Diacylhydrazides were each polycondensed with aromatic dianhydrides, viz., 4,4′-oxydiphthalic anhydride (ODPA), 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) and pyromellitic dianhydride (PMDA) to obtain new poly(amideimide)s. Poly(amideimide)s had inherent viscosity in the range 0.55-0.88 dL/g in N,N-dimethylacetamide (DMAc) at 30 ± 0.1 °C. Poly(amideimide)s were found to be soluble in DMAc, N,N-dimethylformamide (DMF), 1-methyl-2-pyrrolidinone (NMP) and pyridine and could be cast into tough, flexible and transparent films from a solution in DMAc. X-ray diffractograms revealed that poly(amideimide)s with longer alkoxy chains had layered structures. Glass transition temperature of poly(amideimide)s containing pendent flexible alkoxy chains were in the range 215-245 °C. Temperature at 10% weight loss was in the range 380-410 °C in nitrogen atmosphere indicating good thermal stability of poly(amideimide)s.     

Preparation of thermo-responsive polymer brushes on hydrophilic polymeric beads by surface-initiated atom transfer radical polymerization for a highly resolutive separation of peptides

Poly(N-isopropylacrylamide-co-N-tert-butylacrylamide) [P(IPAAm-co-tBAAm)] brushes were prepared on poly(hydroxy methacrylate) (PHMA) [hydrolyzed poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate)] beads having large pores by surface-initiated atom transfer radical polymerization (ATRP) and applied to the stationary phases of thermo-responsive chromatography. Optimized amount of copolymer brushes grafted PHMA beads were able to separate peptides and proteins with narrow peaks and a high resolution. The beads were found to have a specific surface area of 43.0 m²/g by nitrogen gas adsorption method. Copolymer brush of P(IPAAm-co-tBAAm) grafted PHMA beads improved the stationary phase of thermo-responsive chromatography for the all-aqueous separation of peptides and proteins.     

Synthesis of aromatic poly(amide-imide)s from novel diimide-diacid (DIDA) containing sulphone and bulky pendant groups by direct polycondensation with various diamines

A novel diimide-diacid (DIDA) monomer, 4-{4-[(4-methyl phenyl) sulphonyl]}-1,3-bis-trimellitoimido benzene containing sulphone and bulky pendant groups was successfully synthesized and used to synthesize a series of wholly aromatic poly(amide-imide)s (PAIs) by direct polycondensation method. The direct polycondensation of newly synthesized DIDA with different diamines was carried out via Yamazaki’s phosphorylation method using triphenyl phosphite and pyridine system. The resulting poly(amide-imide)s were obtained in quantitative yields with inherent viscosities 0.36-0.47 dl/g in DMAc at 30 ± 0.1 °C. The poly(amide-imide)s were amorphous and were readily soluble in various solvents such as N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethylsulfoxide (DMSO), and pyridine. Tough and flexible films were obtained by casting their DMAc solution. According to thermogravimetric analysis, the polymers were fairly stable up to temperature around 396 °C, and 10% weight losses in the temperature range of 476-511 °C that showed good thermal stabilities of these polymers.