Effects of size constraint on water filling process in nanotube

Molecular dynamics (MD) simulation and the potential of mean force (PMF) analysis are used to investigate the structural properties of water molecules near the end of nanotube for the whole process from the initial water filling up to the configuration stabilization inside the carbon nanotubes (CNTs). Numerical simulations showed that when a small-sized nanotube is immersed into the water bath, the size constraint will induce a prevailing orientation for the water molecule to diffuse into the tube and this effect can persist approximately 3.3 angstroms from the end of CNT. As the structure within the CNTs stabilizes, the ambient structural properties can indirectly reflect their corresponding properties inside the nanotube. Our results also showed that there exists a close correlation between the PMF analysis and the results of MD simulations, and the properties at nanometer scale are closely related to the size-constraint effect.     

The absorption and diffusion of polyethylene chains on the carbon nanotube: The molecular dynamics study

Classical molecular dynamics simulations have been used to investigate the absorption and diffusion behavior of polyethylene (PE) chains on the surface of the side‐wall of the carbon nanotube (CNT). Different degrees of polymerization from 50 to 80 at separate temperatures of 300, 400, 500, and 600 K are considered. Through the simulation, it is examined that the PE chains are absorbed on the surface of CNT and form stable composites with the nanotube as capsules. It is found that the most probable distance between the CNT and the C atoms in backbone of PE molecules only attribute to the temperature, and at T = 300 K, this distance is about 3.8 Å. Furthermore, the pattern of the composites mainly depends on the temperature and the length matching of the chains and the CNT. In particular, the PE chains keep approximately linear conformation, and extend along the axis of the CNT at the room temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 272–280, 2008     

H2 adsorption on Ag‐nanocluster/single‐walled carbon nanotube composites: A molecular dynamics study on the effects of nanocluster size,diameter, and chirality of nanotube

The H₂ physisorption on Ag_N (with N = 32, 108, 256, 500, and 864)/carbon nanotube (CNT; in armchair and zigzag structures with diameters between 0.54 and 2.98 nm) composites were studied by molecular dynamic simulation to investigate the effect of nanocluster size, diameter, and chirality of nanotube on the adsorption phenomena. The calculations indicate that the effects of nanocluster properties are more important than those of the nanotube, in such a way that increase of nanocluster size, decreases the H₂ adsorption. Also, the diameter and chirality of CNTs have considerable influence on the adsorption phenomena. As the diameter of nanotube is increased, the amount of adsorption is decreased. Moreover, H₂ molecules have more tendencies to those nanoclusters located on the armchair nanotubes than the zigzag ones. Another important result is the reversibility of H₂ adsorption on these materials in which the structure of composite in vacuum and after reduction of H₂ pressure to zero, is not changed, considerably. © 2015 Wiley Periodicals, Inc.     

Molecular dynamics simulation of anticancer drug delivery from carbon nanotube using metal nanowires

In this study, we have investigated delivery of cisplatin as the anticancer drug molecules in different carbon nanotubes (CNTs) in the gas phase using molecular dynamics simulation. We examined the shape and composition of the releasing agent by using the different nanowires and nanoclusters. We also investigated the doping effect on the drug delivery process using N-, Si, B-, and Fe-doped CNTs. Different thermodynamics, structural, and dynamical properties have been studied by using the pure and different doped CNTs in this study. Our results show that the doping of the CNT has significant effect on the rate of the drug releasing process regardless of the composition of the releasing agent. © 2019 Wiley Periodicals, Inc.     

Theoretical study of current-voltage characteristics of carbon nanotube wire functionalized with hydrogen atoms

A functionalized single-walled carbon nanotube (SWCNT) of a finite length with a ring-like hydrogenation around its surface is designed toward fabrication of a molecular field-effect transistor (FET) device. The molecular wire thus designed is equipped with a quantum dot inside, which is confirmed by theoretical analysis for electronic transport. In particular, the current-voltage (I-V) characteristics under influence of the gate voltage are discussed in detail.     

Competitive absorption of epoxy monomers on carbon nanotube: A molecular simulation study

Position restrained (PR) molecular dynamics (MD) simulations were carried out on the bulk models for the two composite systems including epoxy monomers and carbon nanotube (CNT). The pair energies and the radial distribution functions (RDFs) were computed to evaluate the relative strength of the epoxy monomers binding to the CNT. It is found that the aromatic amine binds more strongly to the CNT than does the aliphatic amine. A vivid view indicates the aromatic rings tend to form π‐stacking with the CNT, and the compounds with aromatic rings prefer to wrap the CNT. These simulated results are in good agreement with those obtained previously from the vacuum models. This work demonstrates that curing agents affect the interactions between epoxy resin and CNT. Other comparisons of relative binding strength of epoxy monomers also depend upon the temperature. Further analyses suggest that the aliphatic amine exhibits more strong interactions with epoxy resin than does the aromatic amine, mainly due to the presence of hydrogen bonds (HBs) between them. Thus, the ultimate performance of epoxy‐CNT polymer nanocomposites should be affected by the two reverse interactions. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011.     

Effects of multiwalled carbon nanotube on holographic polymer dispersed liquid crystal

The morphology and electro‐optical performance of holographic polymer dispersed liquid crystal (HPDLC) were investigated with the addition of multiwalled carbon nanotube (CNT), both pristine and chemically modified one (CNT‐C?C). With the addition of CNT, the diffraction efficiency increased and showed a maximum at 0.6% while nucleation was delayed due to the increased mixture viscosity. Film was driven only with CNT due to the induced local electric field of polymer to overcome the threshold resistance. Among the two types of CNT, chemically modified one gave finer CNT dispersion, lower mixture viscosity, larger liquid crystal (LC) droplet, higher diffraction efficiency, and shorter response time while the pristine CNT decreased the driving voltage. Copyright © 2010 John Wiley & Sons, Ltd.     

Rapid functionalization of carbon nanotube and its electrocatalysis

It was reported that carbon nanotube (CNT) was functionalized with the electroactive Nile blue (NB), which is a phenoxazine dye, by a method of adsorption to form a NB-CNT nanocomposite. The NB-CNT nanocomposite was characterized by several spectroscopic techniques, for example, Ultraviolet-visible spectroscopy (UV-VIS), Fourier transform infrared (FTIR), Raman spectroscopy and scanning electron microscopy (SEM) etc., and the results showed that NB could rapidly and effectively be adsorbed on the surface of CNT with a high stability without changing the native structure of NB and the structure properties of CNT. Moreover, it was shown that the dispersion ability of CNT in aqueous solution had a significantly improvement after CNT functionalized with NB even at a level of high concentration, for example, 5 mg of NB-CNT per 1 mL of H₂O. The NB-CNT/ glasssy carbon (GC) electrode was fabricated by modifying NB-CNT nanocomposite on the GC electrode surface and its electrochemical properties were investigated by cyclic voltammetry. The cyclic voltammetric results indicate that CNT can improve the electrochemical behavior of NB and greatly enhance its redox peak currents. While the NB-CNT/GC electrode exhibited a pair of well-defined and nearly symmetrical redox peaks with the formal potential of (−0.422±0.002) V (versus SCE, 0.1 mol/L PBS, pH 7.0), which was almost independent on the scan rates, for electrochemical reaction of NB monomer; and the redox peak potential of NB polymer located at about −0.191 V. The experimental results also demonstrated that NB and CNT could synergistically catalyze the electrochemically oxidation of NADH (β-nicotinamide adenine dinucleotide, reduced form) and NB-CNT exhibited a high performance with lowing the overpotential of more than 560 mV. The NB-CNT/GC electrode could effectively sense the concentration of NADH, which was produced during the process of oxidation of substrate (e.g. ethanol) catalyzed by dehydrogenase (e.g. alcohol dehydrogenase). The presented method for functionalization of CNT had several advantages, such as rapid and facile CNT functionalization, easy electrode fabrication and high electrocatalytic activity, etc., and could be used for fabrication electrochemical biosensor on the basis of dehydrogenase. __________ Translated from Acta Chimica Sinica, 2007, 65(1): 1–9 [译自: 化学学报]     

Facile low-temperature polyol process for LiFePO4 nanoplate and carbon nanotube composite

Crystalline LiFePO₄ nanoplates were incorporated with 5 wt.% multi-walled carbon nanotubes (CNTs) via a facile low temperature polyol process, in one single step without any post heat treatment. The CNTs were embedded into the LiFePO₄ particles to form a network to enhance the electrochemical performance of LiFePO₄ electrode for lithium-ion battery applications. The structural and morphological characters of the LiFePO₄–CNT composites were investigated by X-ray diffraction, Fourier Transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy and transmission electron microscopy. The electrochemical properties were analyzed by cyclic voltammetry, electrochemical impedance spectroscopy and charge/discharge tests. Primary results showed that well crystallized olivine-type structure without any impurity phases was developed, and the LiFePO₄–CNT composites exhibited good electrochemical performance, with a reversible specific capacity of 155 mAh g⁻¹ at the current rate of 10 mA g⁻¹, and a capacity retention ratio close to 100% after 100 cycles.     

Reversible electrochemistry of DNA on multi-walled carbon nanotube modified electrode

Calf thymus DNA was electrochemically oxidized at a multi-walled carbon nanotube modified electrode. The potentials for DNA oxidation at pH 7.0 were 0.71 and 0.81 V versus SCE, corresponding to the oxidation of guanine and adenine residues, respectively. The initial 6e-oxidation of adenine, observed in the first scan, resulted a quasi-reversible 2e-redox process of the oxidation product in the following scans.     

胡椒碱在碳纳米管修饰电极上的电化学行为研究

研究了胡椒碱在碳纳米管修饰电极上的电化学行为,在pH为6.4的磷酸盐缓冲溶液中,胡椒碱在-1.12V(vs.SCE)处有一灵敏的还原峰.与裸电极相比,还原峰电位明显正移,峰电流显著增加,表明该修饰电极对胡椒碱的还原反应具有明显的催化作用.峰电流与胡椒碱的浓度在10-6～10-5mol/L范围内呈良好的线性关系(r=0.995),检出限为2.0×10-7mol/L.同时,计算了电荷转移数和扩散系数,考查了修饰电极的重现性,7次平行测量的RSD为4.96%.     

Understanding interactions between poly(styrene-co-sodium styrene sulfonate) and single-walled carbon nanotubes

Understanding formation mechanisms of hybrids of carbon nanotubes (CNTs) wrapped by polymers and their interactions is critical in modifying solubility of CNTs in aqueous solution and developing new nanotube-based polymer materials. In the present work, we investigate the structural details of poly(styrene-co-sodium styrene sulfonate) (PSS) wrapping around the CNT and the interactions between the PSS chain and the CNT using molecular dynamics (MD) simulations. The fraction of sulfonated groups significantly influences the wrapping conformations of the PSS chain. Due to limited time scale in the MD simulations, two different initial conformations of the chains are introduced to explore the effect of the initial state on the wrapping behavior. When the chains initially wrap around the CNT in a perfect helix manner, more compact pseudo-helical conformations are obtained. For initial straight line arrangement of the chain monomers, the chains adopt looser wrapping conformations. The free-energy analysis and binding interaction of the PSS chain on the CNT surface take a glance on the relationship between the conformational transition of the chain and the energy evolution.     

Comprehensive study of threonine adsorption on carbon nanotube: A dispersion complemented density functional theory‐based treatment

The interaction mechanism of threonine (Thr) on the sidewall of (8, 8) single‐walled carbon nanotubes (CNTs) was investigated by density functional tight‐binding method. All the functional groups of Thr were used to interact with the surface of CNT. The structural parameters were analyzed to identify the noncovalent interactions, and the binding energy and strain energy were used to indicate the binding properties. We found that the CH/π interactions play more important roles than NH/π and OH/π interactions in stabilizing the complex structures. Furtherly, the charge transfer properties, density of states (DOS) and partial density of states, and highest occupied molecular orbitals and lowest unoccupied molecular orbitals were also studied to illustrate the adsorbed interactions. The results show that the DOS structure of CNT could be modified by the adsorption of Thr, and, therefore, the conductivity of CNT will be improved by introducing proper amino acids. Our data should be helpful for the design of biocompatible molecules for CNT modification. © 2015 Wiley Periodicals, Inc.     

Iron oxide nanotube film formed on carbon steel for photoelectrochemical water splitting: effect of annealing temperature

Carbon steels (CSs) were anodized in an ethylene glycol solution containing 3 vol.% H₂O and 0.1 m NH₄F to coat with nanotube arrays film. The as anodized nanotube arrays film were annealed in argon atmosphere at various temperatures ranging from 250 to 550 °C for 4 h. The morphology and crystal phases of the film developed after annealing processes were examined using field emission scanning electron microscopy, X‐ray diffraction. Morphology transforms from nanobube arrays to nanotube bundles at 250 °C, to nanobube bundles with nanoflakes at 350 and 450 °C, to nanotube bundles with nanobelts at 550 °C. Amorphous transformed completely into maghemite at 350 °C and hematite with minor magnetite at 450 and 550 °C. Diffuse reflectance ultraviolet and visible spectra revealed iron oxide nanotube film annealed at 350 °C, or higher than 350 °C behaved tremendous absorbance ability in visible spectra range. Mott–Schottky analysis and linear scan voltammetry were performed in 1 m NaOH to show that iron oxide nanotube film annealed at 450 °C exhibited best charge carrier transfer ability upon illumination and superior photoelectrochemical properties compared with the films annealed at other temperatures. The film annealed at 450 °C displayed the photocurrent density of 0.13 mA cm^?2 at 0.2 V_Ag/AgCl, but the film annealed at other temperatures with the photocurrent densities of lower than 0.05 mA cm^?2 at 0.2 V_Ag/AgCl. The morphology and phase transform of iron oxide nanotube film at different annealing temperature results in the change of their photoelectrochemical properties. Copyright © 2016 John Wiley & Sons, Ltd.     

Effects of noncovalently functionalized multiwalled carbon nanotube with hyperbranched polyesters on mechanical properties of epoxy composites

In order to improve the dispersibility and interface properties of multi-walled carbon nanotubes (MWCNTs) in epoxy resin (EP), aromatic hyperbranched polyesters with terminal carboxyl (HBP) and aromatic hyperbranched polyesters with terminal amino groups (HBPN) were used for noncovalent functionalization of MWCNTs. Epoxy composites reinforced by different types of MWCNT were prepared. The effects of noncovalent functionalization of MWCNTs on the dispersibility, wettability, interface properties and mechanical properties of epoxy composites were investigated. The results show that the dispersibility and wettability of MWCNTs are significantly improved after noncovalent functionalization. A large number of terminal primary amines (NH₂) on noncovalently functionalized MWCNT with HBPN (HBPN-MWCNT) form covalent bonds with EP matrix, and thus the interfacial adhesion is enhanced significantly, resulting in high load transfer efficiency and substantial increase in mechanical properties. The interface with covalent bonding formed between the flexible hyperbranched polyester layer on the surface of HBPN-MWCNT and the EP matrix promotes plastic deformation of the surrounding EP matrix. The toughening mechanisms of HBPN-MWCNT are MWCNT pull-out and a large amount of plastic deformation of the surrounding EP matrix.     

The effect of time step,thermostat, and strain rate on ReaxFF simulations of mechanical failure in diamond,graphene, and carbon nanotube

As the sophistication of reactive force fields for molecular modeling continues to increase, their use and applicability has also expanded, sometimes beyond the scope of their original development. Reax Force Field (ReaxFF), for example, was originally developed to model chemical reactions, but is a promising candidate for modeling fracture because of its ability to treat covalent bond cleavage. Performing reliable simulations of a complex process like fracture, however, requires an understanding of the effects that various modeling parameters have on the behavior of the system. This work assesses the effects of time step size, thermostat algorithm and coupling coefficient, and strain rate on the fracture behavior of three carbon‐based materials: graphene, diamond, and a carbon nanotube. It is determined that the simulated stress‐strain behavior is relatively independent of the thermostat algorithm, so long as coupling coefficients are kept above a certain threshold. Likewise, the stress‐strain response of the materials was also independent of the strain rate, if it is kept below a maximum strain rate. Finally, the mechanical properties of the materials predicted by the Chenoweth C/H/O parameterization for ReaxFF are compared with literature values. Some deficiencies in the Chenoweth C/H/O parameterization for predicting mechanical properties of carbon materials are observed. © 2015 Wiley Periodicals, Inc.     

碳纳米管/聚苯胺复合材料的制备及应用研究进展

碳纳米管/聚苯胺复合材料因其独特的电磁学、热力学和机械性能,在很多领域具有潜在应用价值.本文作者对近年来该复合材料的制备方法、性能及应用方面的研究进展进行了综述.     

去甲肾上腺素在多壁碳纳米管修饰玻碳电极上的电化学行为

动物体内的去甲肾上腺素(NE)含量变化反映了肢体神经系统植物交感神经的活动状况,在临床和基础研究中非常重要[1-3]。用化学修饰电极研究儿茶酚胺类神经递质的电化学行为以及对其进行测定是目前分析化学比较活跃的研究领域[4-6]。利用羧基化后的多壁碳纳米管(MWC-NT)对电极表面     

Temperature dependence of the transport of single‐file water molecules through a hydrophobic channel

Although great effort has been made on the transport properties of water molecules through nanometer channels, our understanding on the effect of some basic parameters are still rather poor. In this article, we use molecular dynamics simulations to study the temperature effect on the transport of single‐file water molecules through a hydrophobic channel. Of particular interest is that the water flow and average translocation time both exhibit exponential relations with the temperature. Based on the continuous‐time random‐walk model and Arrhenius equation, we explore some new physical insights on these exponential behaviors. With the increase of temperature, the water dipoles flip more frequently, since the estimated flipping barrier is less than 2 k_BT. Specifically, the flipping frequency also shows an exponential relation with the temperature. Furthermore, the water‐water interaction and water occupancy demonstrate linear relations with the temperature, and the water density profiles along the channel axis can be slightly affected by the temperature. These results not only enhance our knowledge about the temperature effect on the single‐file water transport, but also have potential implications for the design of controllable nanofluidic machines. © 2016 Wiley Periodicals, Inc.