甲基丙烯酸甲酯共聚物的超产特性研究

 用超声脉冲回波法对甲基丙烯酸甲酯-甲基丙烯酸丁酯(MMA-BMA)、含交联剂的甲基丙烯酸甲酯-甲基丙烯酸(MMA-MAA)和苯乙烯-甲基丙烯酸(ST-MAA)等三类共聚物进行了超声衰减和声速实验研究.结果表明,随BMA含量的增加,MMA-BMA共聚物的超声衰减增大,而声速减小;交联剂的加入使共聚物MMA-MAA和ST-MAA的超声衰减明显增大.随着温度的升高,MMA-BMA的超声衰减单调缓慢增加,当温度上升到T_g时则急剧增大.T_g值随BMA的含量增加而降低.文章对上述结果给予了解释.     

甲基丙烯酸甲酯-甲基丙烯酸正丁酯均聚共混物和无规共聚物的裂解色谱定量分析

聚甲基丙烯酸酯类是被广泛应用于工业、建筑、医疗等方面的一类塑料。人们曾经用多种方法对这类材料进行过分析和研究。甲基丙烯酸甲酯(MMA)-甲基丙烯酸正丁酯(BMA)共聚物和均聚共混物的裂解色谱鉴别和定量测定已有报道,但这些方法比较烦琐,不易做准,有的还不完善。本文对聚甲基丙烯酸甲酯(PMMA)-聚甲基丙烯酸正丁酯(PBMA)共混物(简称共混物)和MMA-BMA无规共聚物(简称共聚物)进行了裂解色谱定量研究,探讨了采用回归分析作出的工作曲线的定量方法,以及     

含碘聚甲基丙烯酸酯类X光显影材料的制备

由甲基丙烯酸正丁酯（BMA）与2-(2'-碘苯甲酰)-O-甲基丙烯酸乙酯(2-IEMA)自由基共聚制备了一种X光显影材料。1H NMR分析表明,该共聚物中2种结构单元之比与投料比吻合。GPC测得该共聚物的分子量随2-IEMA含量增加而降低。DSC分析表明,共聚物的玻璃化转变温度在22.3~28.0 ℃之间,与Fox方程计算值比较接近,而且随2-IEMA含量的增加而升高。TGA测得共聚物的分解温度为250 ℃,具有很好的热稳定性。力学性能测试结果表明,共聚物的拉伸强度随BMA含量的增加而增加,最大拉伸强度可达到7.46 MPa。X光显影性测试表明,该共聚物具有良好的显影性,显影效果随2-IEMA含量增加而增强。     

丙烯酸共聚物囊壁的正十八烷微胶囊的制备和性能表征

以二丙烯酸1,4-丁二醇酯为交联剂, 成功制备了甲基丙烯酸甲酯-甲基丙烯酸共聚物为壁材, 正十八烷为囊芯的相变材料微胶囊. 采用扫描电子显微镜(SEM)、差示扫描量热仪(DSC)和热重分析仪(TG)分别考察了单体与芯材投料比、单体浓度和交联剂的含量对微胶囊形貌、相变热性能、热稳定性能的影响. 实验结果表明: 随着单体与芯材投料比或单体浓度的增加, 微胶囊表面均变得致密, 壁厚增加; 随着交联剂含量的增加, 微胶囊的表面变得更加致密光滑, 热稳定性显著增强; 随着单体与芯材投料比的增大, 微胶囊热焓值减小, 被包裹的囊芯含量减少.     

甲基丙烯酸甲酯-甲基丙烯酸无规共聚物的合成及其在乳液聚合中的应用

通过自由基共聚制备了不同组成的甲基丙烯酸甲酯-甲基丙烯酸无规共聚物,用碱中和后作为大分子乳化剂用于乳液聚合.研究了无规共聚物的组成、用量及反应温度对乳液聚合的影响.结果表明,在相同的反应条件下,乳化剂中聚甲基丙烯酸含量越多,乳液聚合速率越快;同一乳化剂,随乳化剂浓度的增加,乳液聚合速率增加;在乳化剂组成、浓度不变的情况下,反应温度越高,乳液聚合速率越大.     

温度及pH敏感性共聚物水凝胶的合成及其对辅酶A的控制释放

以N-乙烯基吡咯烷酮(NVP)和甲基丙烯酸-N,N-二甲胺乙酯(DMAEMA)为单体,采用自由基聚合法合成了NVP与DMAEMA的共聚物及其水凝胶。研究发现共聚物的水溶液具有温度及pH双重敏感特性。相分离温度随DMAEMA含量的增加和水溶液浓度的降低而升高,随pH值的增大而减小且相变敏锐。通过对水凝胶溶胀率的考察,发现共聚凝胶在适当的单体浓度及交联剂浓度下,有较敏感的溶胀-退胀行为。在碱性条件下,共聚凝胶随温度的升高迅速退胀。pH=9时,改变温度,对辅酶A有很好的控制释放;而在酸性条件下,则无退胀行为,对辅酶A不能释放。     

电化学阻抗谱研究聚合物凝胶电解质对染料敏化太阳能电池性能的影响

用甲基丙烯酸β-羟乙酯(HEMA)与N-乙烯基吡咯烷酮(NVP)共聚物P(HEMA-NVP)、甲基丙烯酸甲酯(MMA)与N-乙烯基吡咯烷酮共聚物P(MMA-NVP)为原料制备了聚合物凝胶电解质, 用电化学阻抗谱(EIS)研究了聚合物凝胶电解质中聚合物基质的结构与组成对准固态染料敏化太阳能电池(DSSCs)光伏性能的影响. 不同交联剂用量、不同HEMA用量的P(HEMA-NVP)共聚物及不同MMA用量的P(MMA-NVP)吸收液态电解质后分别形成HGelI、HGelII、MGel凝胶电解质. 结果发现, 随共聚物P(HEMA-NVP)中交联剂由0.1%(w, 下同)增大到0.6%时, 形成的HGelI 组装的DSSCs的光电转化效率(η)先增大后降低, 交联剂用量为0.4%时, DSSCs的η为最大, 为5.54%(光强100 mW·cm^-2). 同时, 比较HGelII 系列和MGel 系列DSSCs的光电性能参数发现, 含有羟基的HGel 系列的η要高于MGel 系列, 而后者的开路电压(V_oc)值高于前者. 在HGelII 系列中, HEMA含量为60%(w)时, DSSCs的η最高. 电化学阻抗谱分析表明共聚物中交联结构的不同影响了电池内部的界面阻抗及离子的传输, 引入羟基有利于降低界面阻抗. 通过调整共聚物中交联剂用量和羟基含量可改善DSSCs的光伏性能.     

丙交脂与聚四亚甲基醚二醇共聚的研究

合成了具有含不同量聚四亚甲基醚二醇(PTMG)的PTMG-PLA嵌段共聚物,并以IR,GPC,′H-NMR,和DSC进行了表征。通过应力-应变曲线研究了共聚物的力学性能。结果表明,共聚物的GPC曲线上只出现单一的流出体积峰,分子量分布多分散系数(?)_n/(?)_n小于2.0;另外,共聚物的T_g随其中的PTMG含量增加而降低,断裂伸长率随共聚物中PTMG含量的增加而增大,而应力,模量等力学性能则随共聚物中PTMG含量增加而降低。共聚物的体外降解速度较PLA均聚物的降解速度平缓。     

蓖麻油聚氨酯和乙烯类聚合物互穿网络材料的生成特点及其动态力学性能

研究蓖麻油聚氨酯/取代乙烯共聚物的互穿网络物(IPN)的生成特点指出,其中取代乙烯游离基共聚的氧化还原引发剂组份-过氧化苯甲酰或二甲基苯胺都能加速聚氨酯网络(Pu)的生成。反应温度在 30℃以上蓖麻油也能参与游离基共聚。蓖麻油不仅与TDI反应生成Pu网络,而且也有小部分参与取代乙烯共聚物长枝链的形成。Pu网络的形成较长枝链的生成为快。生成Pu网络时所放出的热促进取代乙烯与少量蓖麻油的双键共聚,最后生成的IPN不溶于甲苯。这表明生成的是接技的半IPN,而不是单纯的半IPN。动态力学研究指出,包含聚苯乙烯或聚甲基丙烯酸甲酯的这种IPN呈现二个T_g,而只包含聚丙烯腈的仅一个T_g,说明后一IPN中相容性较好,有较多的分子混合。随着聚氨酯与聚取代乙烯的比例减少,二个T_g间的差距减少,而较高温度的T_g随取代乙烯共聚物中丙烯腈含量增加而变小。     

含氟丙烯酸酯共聚乳液及其膜表面特性的研究

以十二烷基硫酸钠 (SDS)和OP 10混合乳化剂 ,制备了甲基丙烯酸全氟辛基乙酯 (FMA8) 甲基丙烯酸丁酯 (BMA) 甲基丙烯酸 (MAA)共聚乳液 .通过DSC、FT IR、1 H NMR对共聚物的结构、组成进行了表征研究 .采用JZHY 180界面张力仪研究了共聚乳液膜表面的性质 ,结果表明 ,随着共聚物中全氟单体含量的增加 ,共聚物膜的表面能显著降低 ,当全氟单体的含量达到 2 5wt %时 ,其表面能降低到 19 74mJ m2 .X ray光电子能谱(XPS)对共聚物表面原子组成的分析结果表明 ,共聚物表面氟的含量远高于其平均含量 ,证明了含氟基团的趋表现象 .经退火处理 ,共聚物膜表面的氟含量增加 ,表面自由能降低     

Photocatalytic degradation of methyl methacrylate copolymers

The photolytic and photocatalytic degradation of the copolymers poly(methyl methacrylate-co-butyl methacrylate) (MMA-BMA), poly(methyl methacrylate-co-ethyl acrylate) (MMA-EA) and poly(methyl methacrylate-co-methacrylic acid) (MMA-MAA) have been carried out in solution in the presence of solution combustion synthesized TiO₂ (CS TiO₂) and commercial Degussa P-25 TiO₂ (DP 25). The degradation rates of the copolymers were compared with the respective homopolymers. The copolymers and the homopolymers degraded randomly along the chain. The degradation rate was determined using continuous distribution kinetics. For all the polymers, CS TiO₂ exhibited superior photo-activity compared to the uncatalysed and DP 25 systems, owing to its high surface hydroxyl content and high specific surface area. The time evolution of the hydroxyl and hydroperoxide stretching vibration in the Fourier transform-infrared (FT-IR) spectra of the copolymers indicated that the degradation rate follows the order MMA-MAA > MMA-EA > MMA-BMA. The same order is observed for the rate coefficients of photocatalytic degradation. The photodegradation rate coefficients were compared with the activation energy of pyrolytic degradation. In degradation by pyrolysis, it was observed that MMA-BMA was the least stable followed by MMA-EA and MMA-MAA. The observed contrast in the order of thermal stability compared to the photo-stability of these copolymers was attributed to the two different mechanisms governing the scission of the polymer and the evolution of the products.     

丙烯酸酯共聚物无皂水溶胶稳定性的研究

用溶液聚合法合成了四种AA含量不同的丙烯酸酯共聚物(MMA/BA/HEMA/AA)，通过中和AA使共聚物带有—COO~-能起自乳化作用分散于水中而成为无皂水溶胶．TEM观察表明水溶胶粒子呈球状，单分散性好，粒径随AA含量增加而变小，在30～90 nm范围．用电导滴定法测定水溶胶粒子中—COOH和—COO~-的分布，表明绝大部分—COO~-处于粒子表面，并且随AA含量增加，粒子表面的—COO~-增多，Zeta电位增大，这是导致水溶胶的抗电解质稳定性(以C.C.C.值反映)和贮存稳定性(以表现粘度反映)随AA含量增加而提高的主要原因。     

OPTICAL PROPERTIES OF IPN-LIKE NETWORKS. II. POLYETHYLENE/POLY-(BUTYLMETHACRYLATE-CO-METHYLMETH-ACRYLATE) COPOLYMER SYSTEMS

IPN-like systems, made of Poly[butylmethacrylate(BMA)-co-methylmethacrylate (MMA)] copolymers and Low Density Polyethylene (PE) networks, were synthesized by a procedure described in previous papers.

The initial PE/copolymer molar ratio was kept constantly equal to one for all the samples. Different molar BMA/MMA copolymer ratios (50/50, 60/40, 80/20, 90/10 100/0) and a molar percentage of 1.0% of the copolymer crosslinker, 1,4-Butandioldimethacrylate (BDDM), were used.

The samples obtained were analyzed by DSC, WAXS, swelling in CCl₄, and dynamic-mechanical tests. PE crystallinity was lowered by the network formation and slightly increased, whereas, the overall network density decreased, with enhancing the BMA content.

Optical investigations were performed in a temperature range between room temperature (R.T.) and 180°C, using MMA as comonomer of BMA, instead of Styrene (S), as well as a different crosslinker (BDDM instead of DVB).

All the IPN's showed the matching-mismatching optical transition of R.I., with temperatures corresponding to a transparency condition. The larger the BMA content, in the initial reactant MMA-BMA comonomeric mixture, the higher such temperatures. An analytical expression was found relating this temperature to the copolymer composition.     

氟硅协同改性丙烯酸树脂的合成与防污性能研究

以甲基丙烯酸十二氟庚酯(FMA)、甲基丙烯酸聚二甲基硅氧烷基酯(SMA)、甲基丙烯酸甲酯、丙烯酸正丁酯、甲基丙烯酸正丁酯和丙烯酸乙酯为共聚单体,通过溶液聚合反应合成出侧链含有机氟、有机硅的丙烯酸树脂.通过核磁共振氢谱(1H-NMR)、核磁共振氟谱(19F-NMR)、红外光谱(FTIR)对聚合物的结构进行了表征.通过扫描电镜(SEM)、接触角测试和生物评价等方法,探讨了FMA、SMA含量对树脂涂膜性能的影响.结果表明氟硅改性的丙烯酸树脂比单独含氟或含硅改性的丙烯酸树脂具有更低的表面能,而且氟硅改性的丙烯酸树脂涂膜比商业化的聚硅氧烷涂膜具有更好的防污性能.     

Preparation,characterization and application of maleic anhydride-modified polylactic acid macromonomer based on direct melt polymerization

A one-pot two-step method based on direct melt polymerization (DMP) for the synthesis of polylactic acid (PLA) macromonomer and its further functionalized application has been developed. The first stage of the reaction is a copolycondensation of lactic acid (LA) and maleic anhydride (MAH) to obtain the macromolecule poly(lactic acid-co-maleic anhydride) (PLAM) with reactive double bonds, and the second stage is a radical copolymerization of different acrylates with PLAM to afford the modified PLA functional materials. The influences of the acrylates have been investigated. The results show that the species with substituted methyl groups in acrylate can polymerize relatively stable. On the other hand, the more carbon atoms in the ester segment of acrylate, the higher intrinsic viscosity [η] and terminal decomposition temperature for the acrylate-modified PLAMs. Among six kinds of acrylates used as the third monomer, such as acrylic acid (AA), methyl acrylate (MA), butyl acrylate (BA), methacrylic acid (MAA), methyl methacrylate (MMA), and butyl methacrylate (BMA), the BMA-modified PLAM has the biggest [η] (0.7566 dL/g) and the terminal decomposition temperature (418 °C) for there are more carbon atoms in BMA. Due to excellent reactivity of the intermediate PLAM, the final modified product can have the anticipated properties for the PLA material by the controllable regulating as different purposes. Thus, this strategy as a green and simple method provides well application prospect for PLA materials in industrial plastics, biomedicine etc.     

Enhancing the flame-retardant and smoke suppression properties of transparent intumescent fire-retardant coatings by introducing boric acid as synergistic agent

A series of novel phosphorus-boron flame retardants (BPEAs) were successfully synthesized by introducing boric acid (BA) into cyclic phosphate ester acid (PEA) via the esterification and thoroughly characterized by ¹H nuclear magnetic resonance spectroscopy and Fourier transform infrared (FTIR) spectroscopy. Five kinds of transparent fire-retardant coatings applied to wood substrates were produced by thoroughly mixing amino resin with PEA and BPEAs. The effects of BA on the optical transparency, thermal stability, fire performance and smoke emission characteristics of the coatings were investigated by various analytical instruments. The transparency analysis reveals that the transparency value of the coatings gradually decreases with increasing BA loading, and MPEA4 with the highest BA content still exhibits a high degree of transparency. The results from fire protection, cone calorimeter and smoke density tests show that the introduction of BA greatly decreases the flame spread rating, mass loss, char index, heat release rate, smoke production rate, total heat release, total smoke release and specific optical density of the coatings concomitant with the increase in the residual mass and intumescent factor, which is ascribed to the formation of a more dense and continuous intumescent char judging by digital photographs and scanning electron microscope images. Thermo-gravimetric analysis indicates that the onset decomposition temperature, high-temperature stability and residual mass of the coatings greatly improve with increasing BA content. FTIR analysis shows that the introduction of BA into the coatings contributes to generate more phosphorus-rich cross-linked structures and aromatic structures and then create a compact and intumescent char layer, thereby effectively enhancing the flame retardancy and smoke suppression properties of the coatings.     

STRUCTURE AND PROPERTIES OF P(MMA-MAA)/PEO INTERMACROMOLECULAR COMPLEX FORMED THROUGH HYDROGEN BONDING

The superstructure and properties of polymers might be improved and enhanced througl intermolecular complexation. In this paper, the preparation, structure and properties of P(MMA-MAA)/PEO intermolecular complex through hydrogen bonding are studied. By acid hydrolysis of PMMA, a series of P(MMA-MAA) copolymers have been prepared, the MAA content of which depends on the temperature and time of hydrolyzation. In case the MAA content in P(MMA-MAA) is beyond 0.4 mole fraction, the hydrogen bonding between P(MMA-MAA) and PEO is strong enough to form intermolecular complex. The supermolecular structure of the complex is quite different from that of its constituent, which was observed by an X-ray diffraction and transmission electron microscope. The crystallization of PEO is confined owing to complexation. The complex exhibits quite a lot of good properties in thermal stability, gas permeability as well as mechanical strength, and could be used in many fields.     

含疏水链节的聚N-异丙基丙烯酰胺共聚物的温敏性

采用溶液聚合法合成了一系列N-异丙基丙烯酰胺(NIPAM)与甲基丙烯酸甲酯、丙烯酸乙酯、丙烯酸丁酯或甲基丙烯酸丁酯的无规共聚物,用浊度观测法和光散射法测定了不同共聚物水溶液的温敏相转变行为.结果表明:所得共聚物的低临界溶解温度(LCST)均低于均聚物PNIPAM的,酯类单体的结构和含量对共聚物的LCST有显著影响,其中酯基上的烷基对共聚物LCST的影响能力大于丙烯酸酯α位上的烷基,前者对增大共聚物的疏水性有更大贡献.通过NIPAM与特定丙烯酸酯单体进行无规共聚可以合成转变温度低于PNIPAM均聚物且具有预设LCST数值的水溶性温敏聚合物.     

乙烯-丙烯酸共聚物非晶区结构和分子运动的固体核磁共振研究

利用固体高分辨1 3CCP MAS和变温固体质子宽线技术对乙烯 丙烯酸共聚物 (EAA)非晶区的结构和分子运动进行了研究 ,结果发现 ,非晶区中羧基之间可以形成氢键 ,其数量随着共聚物中丙烯酸共聚单体含量的增加而增加 ,使得共聚物中非晶区分子运动能力随非晶区相对含量的增加而减弱 ,这是一种与一般的乙烯共聚物相反的变化趋势 .通过交叉极化方法间接测量了非晶区中乙烯链段的1 H自旋 自旋弛豫时间 (T2 ) ,表明非晶区中乙烯链段的运动同样受到氢键的束缚 .随着温度的升高 ,羧基之间的氢键发生解离 ,非晶区的柔性增强