Photocatalytic activity of silver-modified titanium dioxide at solid–liquid and solid–gas interfaces

Silver-modified titania samples (Ag–TiO₂) with varying silver content (0.1–1.0 wt%) were prepared. Silver-modification of titanium dioxide was examined by TEM, XRD, XPS and DR-UV–vis spectroscopy. Ag or AgO_x particles on TiO₂ surface could not be observed by XRD and TEM investigation, however the color of the Ag–TiO₂ samples varied between light rose and purple-brown. XPS measurements revealed that silver exists mainly in oxide form. The photocatalytic activity of pure and Ag–TiO₂ samples were compared both in solid–liquid and in solid–gas interfaces. In the liquid phase the 2,2′-thiodiethanol was used as test molecule. Ethanol photodegradation was examined in gas phase at dry initial condition. It was shown that the rate of photooxidation of organic compounds significantly enhanced by silver-modification of titania.     

制备方法对氧化锰八面体分子筛的NH_3选择性催化还原NO_x性能的影响

采用不同方法制备了一系列氧化锰八面体分子筛(OMS-2)催化剂,考察了制备方法对其低温NH3-SCR催化性能的影响,并采用BET、XRD、Raman、H2-TPR、XPS和TEM等手段对催化剂的物化性质进行表征。结果表明,OMS-2催化剂在50~150℃时其低温SCR活性明显优于MnOx催化剂,OMS-2催化剂在120℃时NOx转化率接近100%。此外,不同的制备方法对OMS-2催化剂的SCR脱硝活性影响明显。其中,固相法制备的OMS-2催化剂的SCR活性最佳。H2-TPR测试结果表明,OMS-2更容易发生氧化还原反应,MnOx还原峰对应的温度较高。XRD、TEM和XPS分析结果表明,低结晶度和高分散性的无定形催化剂有利于低温SCR反应,较高的表面晶格氧和无定形MnO2物种是OMS-2催化剂具有优异低温SCR活性的主要原因。     

方形锐钛矿TiO2纳米晶的合成及表征

在不添加任何模板剂或形状控制剂的条件下,以TiCl₄为前体,经氨水沉淀、乙醇洗涤和超临界干燥(AS制备法)选择性地合成了方形锐钛矿TiO₂纳米单晶.热稳定性研究结果表明,当焙烧温度不超过650℃时,方形锐钛矿TiO₂纳米晶的表面积、孔容、晶粒/颗粒尺寸基本保持不变.XRD和拉曼光谱分析表明,方形锐钛矿TiO₂纳米晶在800℃下焙烧后仍能保持晶相不变,表现出很强的抗晶相转变能力.但在1000℃焙烧后,样品可以完全转变成金红石相TiO₂.     

负载Cu氧化铝纳米管合成及在NO+CH4反应中催化性能研究

采用过氧化氢调节反应条件,在水热体系中合成了新型的勃姆石纳米管,经520℃焙烧2h后,晶型由AlOOH转化为γ-Al2O3;采用XRD、氮吸附、TEM等对合成的纳米管进行表征.结果表明,合成的γ-Al2O3纳米管长约300nm,外径20nm,比表面积达到230m2/g以上.以此为载体,采用等体积浸渍法用Cu(NO3)2...     

焙烧温度对Pt-FeOx/γ-Al2O3催化剂催化甲醛氧化性能的影响

采用胶体沉积法制备了Pt-FeO_x/γ-Al₂O₃催化剂,通过XRD、TEM、BET、XPS、H₂-TPR和FT-IR等技术对催化剂进行了表征,考察了焙烧温度对Pt-FeO_x/γ-Al₂O₃催化剂表面结构及其催化甲醛氧化性能的影响。结果表明,焙烧温度对Pt-FeO_x/γ-Al₂O₃催化剂的氧化还原性能、Pt物种的化学状态以及表面羟基的数量有较大的影响。在室温下,所有Pt-FeO_x/γ-Al₂O₃催化剂均表现出催化氧化活性,其中,200℃焙烧的Pt-FeO_x/γ-Al₂O₃催化剂表现出最好的催化性能,可以将甲醛100%转化为CO₂和H₂O。较低温度焙烧的Pt-FeO_x/γ-Al₂O₃催化剂表面Pt物种具有较好的价态分布以及更多的界面活性位,如Pt-O-Fe物种,因而在温和条件下对甲醛的催化氧化活性较高。     

六棱柱状多晶γ-Al2O3的制备、表征及其形成机制研究

以AlCl₃·6H₂O为前驱物,在氨水介质中用水热法制备了具有新颖形貌特征的六棱柱状多晶γ-Al₂O₃颗粒。采用X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)及N₂物理吸脱附等方法对所制备的γ-Al₂O₃颗粒进行了表征,并对其形貌形成机制进行了分析。结果表明,铝前驱物在氨水介质中通过水热处理后,经焙烧可以形成形貌规整的六棱柱状γ-Al₂O₃颗粒,其边长与长度分别约为0.3 μm和2.5 μm。TEM图片显示,六棱柱颗粒是由尺寸在10 nm左右的粒子聚集而成,因而具有多晶γ相特征。所制备的γ-Al₂O₃材料具有发达的孔隙结构,比表面积为274 cm²/g,孔容为0.51 cm³/g,孔径集中分布在5.5 nm周围。研究发现,γ-Al₂O₃六棱柱形貌的形成机制与AlOOH二次粒子在NH₄⁺正电荷作用下发生的最稳态排列形式具有密切的关联。     

三维有序大孔钙钛矿型氧化物LaFe_(0.7)Co_(0.3)O_3的合成及甲烷化学链水蒸气重整性能

采用无皂乳液聚合法制备聚苯乙烯(PS)微球,通过自组装得到排列均匀有序的聚苯乙烯(PS)胶晶模板,然后经过浸渍和煅烧得到三维有序大孔(3DOM)钙钛矿型氧化物LaFe_(0.7)Co_(0.3)O_3。通过扫描电镜、透射电镜和X射线衍射等手段对制备的3DOM钙钛矿型氧化物LaFe_(0.7)Co_(0.3)O_3的物理化学性能进行表征。在固定床反应器上考察3DOM LaFe_(0.7)Co_(0.3)O_3的甲烷化学链水蒸气重整性能。结果表明,聚苯乙烯(PS)微球粒径受苯乙烯单体使用量的影响,随着苯乙烯单体使用量的增加聚苯乙烯(PS)微球粒径呈增大的趋势;煅烧温度对三维有序大孔结构有显著影响,浸渍后模板在500℃煅烧下即能形成三维有序大孔结构比表面积达到19.820 m2/g,随着煅烧温度的升高三维有序大孔结构遭到部分破坏,在900℃煅烧下三维有序大孔结构遭到完全破坏。在氧载体与甲烷的反应前期,气体产物中CO2含量较高,是表面吸附氧将甲烷完全氧化所致,在表面吸附氧消耗完后体相晶格氧将甲烷部分氧化生成H2与CO。在水蒸气氧化阶段,水蒸气与还原态的氧载体发生反应生成氢气,产氢率为4.0-5.0 mmol/g。同时水蒸气氧化阶段气相产物中CO和CO2含量很低,说明3DOM LaFe_(0.7)Co_(0.3)O_3具有优秀的抗积炭性能。     

Synthesis and Characterization of Photocatalytic Porous Fe3+/TiO2 Layers on Glass

Wet chemical synthesis and preliminary photocatalytical characteristics of titania and Fe(III)-containing TiO₂ layers are presented. A highly stable coating colloids could be prepared under base- as well as acid-catalyzed condensation conditions. Structural properties of the as-prepared wet gels and sintered films were investigated using SEM, TEM, XRD as well as optical absorption spectroscopy, DTA-TG analysis and photomineralisation studies. X-ray amorphous wet titania gel layers start to crystallize at 500°C forming the characteristic anatase phase. In the presence of iron ions (Fe/Ti = 1), nanocrystalline FeTiO₃ ilmenite phase forms. Both TiO₂ and Fe-containing TiO₂ films demonstrate a photocatalytic activity in the process of the photomineralization of dichloroacetic acid.     

脉冲电磁场辅助浸渍法制备CoMo/γ-Al_2O_3加氢脱硫催化剂

利用脉冲电磁场(PEMF)辅助浸渍法和常规等体积浸渍法制备了一系列CoMo/γ-Al_2O_3加氢脱硫催化剂样品。以噻吩、2-甲基噻吩或苯并噻吩为模型化合物,在微反装置上评价了催化剂的加氢脱硫活性,经200 V脉冲电磁场处理的催化剂上各硫化物的转化率均比常规催化剂明显提高。采用XRD、BET、H_2-TPR和TEM等方法表征了催化剂样品的表面状态和物化性质。结果表明,适当强度的脉冲电磁场与制备体系内带电粒子的交互作用有助于催化剂活性组分的分散,使活性组分在γ-Al_2O_3载体表面分布更为均匀,同时削弱了活性组分MoO_3同载体间的较强相互作用,降低了催化剂表面钼物种的还原温度,促进了CoMoS活性相的形成。     

单一板钛矿相TiO2微晶的制备

以新鲜的无定形TiO₂沉淀为前驱体,在水热条件下得到了板钛矿型TiO₂微晶粉末,考察了前驱体制备过程中碱的种类与用量以及水热反应的温度和时间等因素对板钛矿型TiO₂的影响.XRD,TEM和Raman测试表明,所合成的样品具有单一的板钛矿型TiO₂结构,晶相纯度很高,晶粒形状相同且具有完美的内部结构,粒度分布均匀.此板钛矿型TiO₂样品在900℃时开始向金红石结构转化,1000℃时完全转变为金红石结构.     

NOx在担载CeO2的纳米ZrO2上的吸附研究

通过反相微乳液法制备了纳米级高比表面积ZrO₂粉体材料,用TEM,XRD和氮气吸附BET比表面积等手段对其进行了表征,研究了Ce(NO₃)₃溶液浸渍的ZrO₂粉体对氮氧化物的吸附活性.实验结果表明,5%Ce/ZrO₂样品室温时可吸附NO_x的最大值为34.5mg;100℃时为17.5mg;200℃时可达9.5mg.对比表明,同样条件下微乳液法制备的ZrO₂对NO_x的最大吸附量是一般沉淀法制备的ZrO₂样品的2.5倍.纳米级ZrO₂的特殊孔结构可能是导致微乳液法制备的ZrO₂样品吸附量较高的主要原因.     

焙烧温度对微乳液法负载铂制备的Pt-S2O82-/ZrO2-Al2O3催化剂异构化性能的影响

过微乳液法负载Pt制备了Pt-S₂O₈^2-/ZrO₂-Al₂O₃(Pt-SZA-X) 催化剂,并采用XRD、BET、FT-IR、TPR、TEM等手段对催化剂进行了表征。以正戊烷异构化反应为探针,考察了焙烧温度对催化剂异构化性能的影响。结果表明,焙烧温度对Pt-SZA-X的还原温度影响不大,但催化剂表面S含量随着焙烧温度的升高而下降;焙烧温度为600~650℃时形成O=S=O结构,此时S与催化剂载体结合比较稳定;焙烧温度为650℃时,可得到单一的ZrO₂四方晶相,焙烧温度高于650℃时,比表面积迅速降低,催化剂表面S⁶⁺流失严重。在不同温度下焙烧得到的催化剂中,经650℃焙烧的催化剂具有适宜的超强酸位和比表面积,异构化活性最高。在反应温度为230℃、反应压力2.0 MPa、氢烃物质的量比4:1、质量空速1.0 h^-1时,催化异戊烷产率达到60.8%。     

Ni-Pt/γ-Al2O3催化剂用于甲基环己烷催化脱氢的研究

采用自制的比表面积为349 m²/g的纳米膜γ-Al₂O₃为载体,用等体积浸渍法制备了Ni-Pt/γ-Al₂O₃催化剂,采用比表面积测定、X射线衍射、扫描电镜和透射电镜等手段对所制备的催化剂进行了表征。利用微型连续管式反应器与气相色谱联用装置,考察了Ni-Pt/γ-Al₂O₃催化剂对甲基环己烷(MCH)气相脱氢的催化性能。结果表明,使用20%Ni-0.5%Pt/γ-Al₂O₃催化剂,在反应温度350℃,混合进样体积空速252 h^-1条件下,甲苯转化率达到96.99%,选择性接近100%。     

Lanthanum-based perovskites obtained in molten nitrates or nitrites

Lanthanum-based perovskites, LaMO₃ (where M = Mn, Fe, Co, Ni), have been synthesised from lanthanum precursors and corresponding 3d transition metal salts in molten alkali metal nitrates or nitrites. The reactivity of eight precursors in three molten salts of different basicity was analysed. Single phase orthorhombic LaMnO_3.11, and orthorhombic LaFeO₃ have been obtained in molten NaNO₂ at 723 K, for 2 h. LaCoO₃ is also formed in molten nitrite, but an increase of basicity, by adding Na₂O₂, was necessary to obtain LaNiO₃. The reaction systems were investigated by thermal analysis. X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and specific surface area measurements (BET method) were used to characterise the synthesised nanopowders.     

石墨烯的制备

以球形石墨为原料, HClO₄为插层剂,KClO₃为氧化剂,采用高温(1 050 ℃)氧化还原法制备了石墨烯（GN）,其结构和性能经FT-IR, XRD, SEM, TEM, BET和RS等表征。研究了KClO₃的加入量对GN结构和性能的影响,结果表明:当KClO₃的加入量为0.08 g·mL^-1时,所制备的GN的比表面积为558 m²·g^-1,平均孔径为3.012 nm,电阻率为0.02 Ω·cm。     

Effect of Lanthanum on Catalytic Performance of Ru/Al2O3 Catalyst for Hydrogenation of Esters to Corresponding Alcohols

Ru-La/γ-Al₂O₃ catalyst was prepared by impregnation method and characterized by temperature programmed reduction(TPR), transmission electron microscopy(TEM), X-ray photoelectron spectra(XPS), Brunauer- Emmett-Teller(BET), X-ray diffraction(XRD), and NH₃-temperature programmed desorption(NH₃-TPD). NH₃-TPD revealed that the strong acidic centers in γ-Al₂O₃ are not the major factor to cause the hydrolysis of esters to acids in the hydrogenation of esters. The results of TPR and TEM indicate that the appropriately added lanthanum results in the good dispersion of ruthenium and the easy reduction of ruthenium oxide on Ru-La/γ-Al₂O₃, which could promote the catalytic activity of Ru-La/γ-Al₂O₃ for the hydrogenation of methyl propionate to propanol. When the amount of lanthanum added in the catalyst was up to 9%(mass fraction), 4%Ru-9%La/γ-Al₂O₃ catalyst gave a conversion of methyl propionate of 98.1% and a selectivity of 94.8% to propanol at a reaction temperature of 180 ℃ and a hydrogen pressure of 5.0 MPa.     

LaSrCo0.9B’0.1O4复合氧化物制备、氧化性能及表征

采用聚丙烯酰胺法制备了类钙钛矿LaSrCo_0.9B’_0.1O₄系列复合氧化物(B’= Mn、Fe、Ni、Cu)和LaSrCoO₄,并考察了对CO和C₃H₈催化氧化反应的活性,运用XRD、BET、TEM、TPD等方法对LaSrCo_0.9Ni_0.1O₄、LaSrCoO₄进行了表征.结果表明, LaSrCo_0.9Ni_0.1O₄和LaSrCoO₄都为四方K₂NiF₄型纳米材料. Ni的掺入提高了LaSrCoO₄的催化活性、O₂的吸附量和晶格畸变率,降低了平均晶粒度.     

乙烷部分氧化制C2氧化物用Fe－Al－P－O催化剂的研究Ⅰ．超细Fe－Al－P－O催化剂的制备与表征

 用溶胶－凝胶法制备了超细Fe－Al－P－O催化剂，并用DTA－TG，BET，TEM，XRD，TPR和IR等技术研究了催化剂的微观组成和结构及其晶格氧活性，探讨了催化剂的制备工艺，考察了溶胶－凝胶的形成机理、凝胶干燥及焙烧条件对催化剂微观组成和结构的影响规律．结果表明，Fe－Al－P－O催化剂呈非晶态，是具有均匀分布的超细粒子（10nm），其比表面积大（238m2／g），晶格氧活性高．FePO4和AlPO4间隔分布在催化剂表面，形成Lewis碱位（P＝O，P－O－Fe）和Lewis酸位（Fe3＋，Al3＋）．     

Fe2(MoO4)3超细微粒催化剂的制备

近年来，超细微粒因其具有明显的体积效应和表面效应已被广泛应用于陶瓷、光学、电磁、生物、染料、医药、农业等领域［‘，‘l其中复合氧化物超细微粒是近年来国内外正致力开发的一种新型催化材料，有关这类材料的制备、表征和催化性能的研究有重要的理论和实际意义．文献报导     

Synthesis of nanosized TiO2 particles in reverse micelle systems and their photocatalytic activity for degradation of toluene in gas phase

Nanosized pure TiO₂ particles with high crystallinity and large surface area were prepared by hydrolysis of tetrabutyl titanate in water/Triton X-100/isooctane reverse micelle solutions as reaction media followed by hydrothermal treatment to improve crystallinity. The prepared TiO₂ nanoparticles were characterized by XRD, BET, TGA, FT-IR and TEM. The size of ultrafine particles was controlled by changing the water content of the reverse micelle solution. The TiO₂ particles showed monodispersity, large surface area and high degrees of crystallinity and thermostability. The photocatalytic activity of the TiO₂ particles was evaluated by decomposition of toluene in the gas phase. The activity of the TiO₂ nanoparticles was higher than that of commercially available anatase fine particles, such as ST-01, which is one of the most active photocatalysts for degradation of organic compounds in the gas phase.