An evoluted bio-based 2,5-furandicarboxylate copolyester fiber from poly(ethylene terephthalate)

A series of bio-based poly(ethylene terephthalate-co-ethylene 2,5-furandicarboxylate) (PEFT) fibers was prepared via the industrially feasible melt-spinning and hot-drawing process. The effect of 2,5-furandicarboxylic acid (FDCA) content on the fibers properties was studied using differential scanning calorimetry, wide-angle X-ray diffraction, sound velocity, tensile, and boiling water shrinkage tests. It was found that the PEFT fibers showed comparable or superior tenacity to the PET fibers under the same conditions, especially the PEFT-4 fibers exhibited the highest tenacity (2.3, 2.9 cN/dtex for the drawn PET and PEFT-4 fibers prepared at the same take-up speed of 2500 m/min and a fixed draw ratio of 1.6). Moreover, the boiling water shrinkage of the PEFT fibers was quite close to that of the PET fibers under the same conditions, showing that the PEFT fibers were comparable to the PET fibers in heat resistance. The results indicated that the bio-based PEFT fibers would be a feasible alternative for the PET fibers, in terms of sustainability, processability, and mechanical properties. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 320–329     

氯化聚丙撑碳酸酯增容聚丙撑碳酸酯/秸秆粉复合材料的制备及性能

聚丙撑碳酸酯(PPC)是一种新型热塑性生物降解材料,但其热性能及力学性能较差,应用受到限制。以秸秆粉这种农作物副产品作为增强体改性PPC,既可以提高PPC的力学性能同时又可开发利用秸秆资源。氯化聚丙撑碳酸酯(CPPC)是聚丙撑碳酸酯(PPC)经过氯化得到的,对天然纤维表面具有良好的浸润性和粘结性。本文以CPPC为增容剂,通过熔融共混法制备了PPC/秸秆粉复合材料。采用扫描电子显微镜(SEM)、拉伸实验、动态力学性能测试(DMA)及转矩流变仪对复合材料的结构及性能进行了表征,重点考察了CPPC的添加量对复合材料力学和流变性能的影响。结果表明,当CPPC质量分数为1.8%时,可使添加质量分数为30%秸秆粉的PPC复合材料拉伸强度提高38%,模量提高30%。同时,CPPC的引入使复合材料的粘度下降,改善了PPC/秸秆粉复合材料的加工性能。因此,作为增容剂的CPPC为制备高性能PPC/天然纤维复合材料提供了新的解决办法。     

Fracture evaluation of plasticized polylactic acid / poly (3-HYDROXYBUTYRATE) blends for commodities replacement in packaging applications

Nowadays, scientific and technological efforts are being carried out to diminish serious ecological problems caused by indiscriminate use of non-biocompostable polymers in the packaging industry. In this sense, novel biodegradable blends of different composition based on poly(lactic acid) (PLA), poly(3-hydroxybutyrate) (PHB) and tributyrin (TB) are developed and here proposed as an eco-friendly alternative. Materials are characterized by fracture experiments under quasi-static and biaxial impact loading. Fracture behavior is analyzed together with thermal, tensile and water permeation properties to evaluate their potential in-service performance. TB_PLA/PHB blends with 15 wt% TB exhibit better permeation and fracture toughness than currently used bio-based polymers, being in the range of polyethylene properties. Results highlight the potential of these new blends broadening the current application field of PLA.     

Preparation and characterization of formaldehyde-modified black liquor lignin/poly (propylene carbonate) composites

In this paper, the black liquor lignin (BL) from pulp and paper industry was chemically modified using formaldehyde to adjust its aggregation structure and dispersion behavior. The properties of the formaldehyde-modified black liquor lignin (BLF) were measured by Fourier transform infrared spectroscopy, transmission electron microscopy, and differential scanning calorimetry. Results indicated that the BLF had better dispersion ability than BL. Therefore, the BLF as reinforcing fillers was incorporated into poly(propylene carbonate) (PPC) by melt compounding to prepare biodegradable BLF/PPC composites. The tensile properties, microstructure, thermal decomposition properties, and rheological properties of the BLF/PPC composites were investigated. Results showed that the performance of composites was depend on the dispersion of BLF. After adding a small amount of BLF into PPC, the tensile strength, tensile modulus, thermal stability, and processing stability of the composite were significantly improved.     

Effects of Wood Flour (WF) Pretreatment and the Addition of a Toughening Agent on the Properties of FDM 3D-Printed WF/Poly(lactic acid) Biocomposites

In order to improve the properties of wood flour (WF)/poly(lactic acid) (PLA) 3D-printed composites, WF was treated with a silane coupling agent (KH550) and acetic anhydride (Ac₂O), respectively. The effects of WF modification and the addition of acrylicester resin (ACR) as a toughening agent on the flowability of WF/PLA composite filament and the mechanical, thermal, dynamic mechanical thermal and water absorption properties of fused deposition modeling (FDM) 3D-printed WF/PLA specimens were investigated. The results indicated that the melt index (MI) of the specimens decreased after WF pretreatment or the addition of ACR, while the die swell ratio increased; KH550-modified WF/PLA had greater tensile strength, tensile modulus and impact strength, while Ac₂O-modified WF/PLA had greater tensile modulus, flexural strength, flexural modulus and impact strength than unmodified WF/PLA; after the addition of ACR, all the strengths and moduli of WF/PLA could be improved; after WF pretreatment or the addition of ACR, the thermal decomposition temperature, storage modulus and glass transition temperature of WF/PLA were all increased, and water absorption was reduced.     

Fiber property and structure development of polyester blend fibers reinforced with a thermotropic liquid‐crystal polymer

Ternary blend fibers (TBFs), based on melt blends of poly(ethylene 2,6‐naphthalate), poly(ethylene terephthalate), and a thermotropic liquid‐crystal polymer (TLCP), were prepared by a process of melt blending and spinning to achieve high‐performance fibers. The reinforcement effect of the polymer matrix by the TLCP component, the fibrillar structure with TLCP fibrils of high aspect ratios, and the development of more ordered and perfect crystalline structures by an annealing process resulted in the improvement of the tensile strength and modulus for the TBFs. An increase in the apparent crystallite size with the spinning speed was attributed to the development of larger crystallites and more ordered crystalline structures in the annealed TBFs. The birefringence and density of the TBFs increased with increasing spinning speed, the TBFs becoming more oriented and the crystal packing becoming more enhanced. The molecular orientation was an important factor in determining the tensile strength and modulus of the TBFs. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 395–403, 2004     

Efficient barrier properties of mechanically enhanced agro-extracted cellulosic biocomposites

The objective of this work was to prepare the mechanically stable hydrophobic biocomposites by incorporating the cellulose fibers into the polymer matrices for their applications in biomedical and food packaging. Herein, two different types of biocomposites were prepared by mixing polylactic acid (PLA) and polyhydroxybutyrate (PHB) with the agro-extracted cellulose, separately at 170 °C. The influence of the cellulose fibers on the thermal, mechanical, and barrier properties of polymer matrices (PLA and PHB) was observed. With an increase in the cellulose content in PLA and PHB, the tensile strength of the biocomposite materials significantly improved with the enhancement of 24.45% and 32.08%, respectively, compared with the pure PLA and PHB. Furthermore, a decrease of 74.16% and 73.49% in the water vapor transmission rate and oxygen transmission rate, respectively, was observed for cellulose/PHB biocomposites. This study highlights that adding cellulose fibers significantly improves the mechanical and the barrier properties of PLA and PHB, suggesting their biocomposites for use in biodegradable polymer industries.     

Gamma Irradiation Effects on Mechanical and Thermal Properties and Biodegradation of Poly(3-hydroxybutyrate) Based Films

Summary: Their biodegradable properties make polyhydroxyalkanoates (PHAs) ideal candidates for innovative applications. Many studies have been primarily oriented to poly(3-hydroxybutyrate) (PHB) and poly(3-hydroxybutyrate-co-3-valerate) (PHBV) and afterwards to blends of PHAs with synthetic biodegradable polymers, such as poly(ε-caprolactone) (PCL). Medical and pharmaceutical devices require sterilization and γ irradiation could provide a proper alternative since it assures storage stability and microbiological safety. This contribution presents the effect of γ irradiation on the mechanical and thermal properties and on the biodegradation of PHB, PHBV and a commercial PHB/PCL blend. Samples, prepared by compression moulding, were irradiated in air at a constant dose rate of 10 kGy/h, from 10 to 179 kGy. Polymer chain scission was assessed by changes in the molecular weight, thermal properties and tensile behaviour. The correlation between absorbed dose and changes in the mechanical properties and biodegradation is discussed in detail. The optimum dose to guarantee microbiological sterilization without damage of the structure or meaningful loss of the mechanical properties is also reported.     

聚β-羟基丁酸酯/聚氧化乙烯共混体系力学性能研究

本文详细研究了可完全生物降解的聚 β 羟基丁酸酯 (PHB)与水溶性聚氧化乙烯 (PEO)两元共混体系的拉伸力学性能 .讨论了PEO分子量、共混组成及热处理条件对共混体系力学性能的影响 .其中 ,PHB与超高分子量PEO(重均分子量 5× 10 6)共混 ,两组分力学上具有相容性 ,共混物的拉伸强度、断裂伸长率及模量都有明显的正的协同效应 .共混改性效果显著PHB的力学性能得到很大改善 ,尤其PHB的脆性缺陷 .并且 ,共混物在经过适当温度退火处理之后 ,共混物性能还可进一步改善     

Property correlations for composites based on ethylene propylene diene rubber reinforced with flax fibers

EPDM composites filled with short flax fibers were prepared by melt blending procedure. The effects of fiber loading on the mechanical, thermal and water uptake characteristics were studied. The physico-mechanical, morphological thermal properties and water absorption behavior were discussed using tensile testing, differential scanning calorimetry, thermogravimetrical analysis and scanning electron microscopy. Scanning electron microscopy revealed that the flax fibers were well dispersed in the polymer matrix. The tensile strength and hardness of the composites were found to be improved at higher fiber loading. The water absorption pattern of EPDM/fiber composites at room temperature follows a Fickian behavior for composites with 10, 15 and 20 phr flax fiber.     

Effect of poly(vinyl acetate) (PVAc) on thermal behavior and mechanical properties of poly(3-hydroxybutyrate)/poly(propylene carbonate) (PHB/PPC) blends

To assess the compatibility of blends of synthetic poly(propylene carbonate) (PPC), with a natural bacterial poly(3-hydroxybutyrate) (PHB), a simple casting procedure of blend was used. poly(3-hydroxybutyrate)/poly(propylene carbonate) blends are found to be incompatible according to DSC and DMA analysis. In order to improve the compatibility and mechanical properties of PHB/PPC blends, poly(vinyl acetate) (PVAc) was added as a compatibilizer. The effects of PVAc on the thermal behavior, morphology, and mechanical properties of 70PHB/30PPC blend were investigated. The results show that the melting point and the crystallization temperature of PHB in blends decrease with the increase of PVAc content in blends, the loss factor changes from two separate peaks of 70PHB/30PPC blend to one peak of 70PHB/30PPC/12PVAc blend. It is also found that adding PVAc into 70PHB/30PPC blend can decrease the size of dispersed phase from morphology analysis. The result of tensile properties shows that PVAc can increase the tensile strength and Young’s modulus of 70PHB/30PPC blend, and both the elongation at break and the tensile toughness increase significantly with PVAc added into 70PHB/30PPC.     

碳纳米管改性聚苯硫醚熔纺纤维的结构与性能研究

将多壁碳纳米管(MWCNTs)和聚苯硫醚(PPS)经过熔融挤出后制备成复合材料切片,并采用熔融纺丝法制得碳纳米管改性聚苯硫醚复合纤维.采用扫描电镜(SEM)、拉曼光谱、示差扫描量热分析(DSC)、动态机械分析(DMA)以及力学性能测试等表征手段研究了复合纤维中碳管的分散状态,与基体的界面作用,复合纤维的结晶性能以及力学性能,从而探讨了聚苯硫醚/碳纳米管复合纤维体系的微观结构与宏观性能之间的关系.研究表明,聚苯硫醚分子结构与碳纳米管之间具有的π-π共轭作用使碳管较为均匀的分散在基体中,界面结合较为紧密.同时熔融纺丝过程中的拉伸作用使碳管进一步解缠并使碳管沿纤维拉伸方向取向.另一方面,拉曼光谱显示拉伸作用有效地增强了界面作用,有利于外界应力的传递.碳管的良好分散以及强的界面作用使复合纤维力学性能得到大幅度的提高,当碳管含量达到5 wt%时,复合纤维的模量有了明显的提高,拉伸强度较纯PPS纤维提高了近220%.     

Electrospun fiber mats of poly(3‐hydroxybutyrate), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate), and their blends

Electrospinning of poly(3‐hydroxybutyrate) (PHB), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV), and their blends was first carried out in chloroform at 50 °C on a stationary collector. The average diameter of the as‐spun fiber from PHB and PHBV solutions decreased with increasing collection distance and increased with increasing solution concentration and applied electrical potential. In all of the spinning conditions investigated, the average diameter of the as‐spun pure fibers ranged between 1.6 and 8.8 μm. Electrospinning of PHB, PHBV, and their blends was carried out further at a fixed solution concentration of 14% w/v on a homemade rotating cylindrical collector. Well‐aligned, cross‐sectionally round fibers without beads were obtained. The average diameter of the as‐spun pure and blend fibers ranged between 2.3 and 4.0 μm. The as‐spun fiber mats appeared to be more hydrophobic than the corresponding films and much improvement in the tensile strength and the elongation at break was observed for the blend fiber mats over those of the pure fiber ones. Lastly, indirect cytotoxicity evaluation of the as‐spun pure and blend fiber mats with mouse fibroblasts (L929) indicated that these mats posed no threat to the cells. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2923–2933, 2006     

Crystallization and morphology of poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) blends. II. Morphology and crystallization kinetics by time resolved X‐ray scattering

The development of the morphology in poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) (PVDF/PHB) blends upon isothermal and anisothermal crystallization is investigated by time‐resolved small‐ and wide‐angle X‐ray scattering. The components are completely miscible in the melt but crystallize separately; they crystallize stepwise at different temperatures or sequentially with isothermal or anisothermal conditions, respectively. The PVDF crystallizes undisturbed whereas PHB crystallizes in a confined space that is determined by the existing supermolecular structure of the PVDF. The investigations reveal that composition inhomogeneities may initially develop in the remaining melt or in the amorphous phases of the PVDF upon crystallization of that component. The subsequent crystallization of the PHB depends on these heterogeneities and the supermolecular structure of PVDF (dendritically or globularly spherulitic). PHB may form separate spherulites that start to grow from the melt, or it may develop “interlocking spherulites” that start to grow from inside a PVDF spherulite. Occasionally, a large number of PVDF spherulites may be incorporated into PHB interlocking spherulites. The separate PHB spherulites may intrude into the PVDF spherulites upon further growth, which results in “interpenetrating spherulites.” Interlocking and interpenetrating are realized by the growth of separate lamellar stacks (“fibrils”) of the blend components. There is no interlamellar growth. The growth direction of the PHB fibrils follows that of the existing PVDF fibrils. Depending on the distribution of the PHB molecules on the interlamellar and interfibrillar PVDF regions, the lamellar arrangement of the PVDF may contract or expand upon PHB crystallization and the adjacent fibrils of the two components are linked or clearly separated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 974–985, 2004     

Mechanical properties and structure of the zone‐drawn poly(L‐lactic acid) fibers

The zone‐drawing (ZD) method was applied three times to the melt‐spun poly(L ‐lactic acid) (PLLA) fibers of low molecular weight (M_v = 13,100) at different temperatures under various tensions. The mechanical properties and superstructure of the ZD fibers were investigated. The resulting ZD‐3 fiber had a draw ratio of 10.5, birefringence of 37.31 × 10⁻³, and crystallinity of 37%, while an orientation factor of crystallites remarkably increased to 0.985 by the ZD‐1. The Young's modulus and tensile strength of the ZD‐3 fiber respectively attained 9.1 GPa and 275 MPa, and the dynamic storage modulus was 10.4 GPa at room temperature. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 991–996, 1999     

Nonisothermal crystallization and melting behavior of poly(β‐hydroxybutyrate)–Poly(vinyl‐acetate) blends

Nonisothermal crystallization and melting behavior of poly(β‐hydroxybutyrate) (PHB)–poly(vinyl acetate) (PVAc) blends from the melt were investigated by differential scanning calorimetry using various cooling rates. The results show that crystallization of PHB from the melt in the PHB–PVAc blends depends greatly upon cooling rates and blend compositions. For a given composition, the crystallization process begins at higher temperatures when slower scanning rates are used. At a given cooling rate, the presence of PVAc reduces the overall PHB crystallization rate. The Avrami analysis modified by Jeziorny and a new method were used to describe the nonisothermal crystallization process of PHB–PVAc blends very well. The double‐melting phenomenon is found to be caused by crystallization during heating in DSC. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 443–450, 1999     

Poly(lactic acid)/Poly(3-hydroxybutyrate) Biocomposites with Differently Treated Cellulose Fibers

The growing concern about environmental pollution has generated an increased demand for biobased and biodegradable materials intended particularly for the packaging sector. Thus, this study focuses on the effect of two different cellulosic reinforcements and plasticized poly(3-hydroxybutyrate) (PHB) on the properties of poly(lactic acid) (PLA). The cellulose fibers containing lignin (CFw) were isolated from wood waste by mechanical treatment, while the ones without lignin (CF) were obtained from pure cellulose by acid hydrolysis. The biocomposites were prepared by means of a melt compounding-masterbatch technique for the better dispersion of additives. The effect of the presence or absence of lignin and of the size of the cellulosic fibers on the properties of PLA and PLA/PHB was emphasized by using in situ X-ray diffraction, polarized optical microscopy, atomic force microscopy, and mechanical and thermal analyses. An improvement of the mechanical properties of PLA and PLA/PHB was achieved in the presence of CF fibers due to their smaller size, while CFw fibers promoted an increased thermal stability of PLA/PHB, owing to the presence of lignin. The overall thermal and mechanical results show the great potential of using cheap cellulose fibers from wood waste to obtain PLA/PHB-based materials for packaging applications as an alternative to using fossil based materials. In addition, in situ X-ray diffraction analysis over a large temperature range has proven to be a useful technique to better understand changes in the crystal structure of complex biomaterials.     

Development of continuous process enabling nanofibrillation of pulp and melt compounding

Microfibrillated cellulose (MFC), a mechanically fibrillated pulp mostly consisting of nanofibrils, is a very attractive material because of its high elastic modulus and strength. Although much research has been done on composites of MFC and polypropylene (PP), it has been difficult to produce such composites at an industrial level because of the difficulties in using MFC in such composites are not only connected to the polarity (that can be improved with compatibilizers), but also with the challenge to make a homogeneous blend of the components, and also the low temperature stability of cellulose that could cause problems during processing. We developed a new processing method which enables continuous microfibrillation of pulp and its melt compounding with PP. Never-dried kraft pulp and powdered PP were used as raw materials to obtain MFC by kneading via a twin-screw extruder. Scanning electron microscopy showed nano to submicron wide fibers entangled in the powdered PP. MFC did not aggregate during the melt compounding process, during which the water content was evaporated. Maleic anhydride polypropylene (MAPP) was used as a compatibilizer to reinforce interfacial adhesion between the polar hydroxyl groups of MFC and non-polar PP. We investigated the effect of MAPP content on the mechanical properties of the composite, which were drastically improved by MAPP addition. Needle-leaf unbleached kraft pulp (NUKP)-derived MFC composites had better mechanical properties than needle-leaf bleached kraft pulp (NBKP)-derived MFC composites. Injection molded NUKP-derived MFC composites had good mechanical and thermal properties. The tensile modulus of 50 wt% MFC composite was two times, and the tensile strength 1.5 times higher than that of neat PP. The heat distortion temperature of 50 wt% MFC content composite under 1.82 MPa flexural load was increased by 53 °C, from 69 to 122 °C. This newly developed continuous process using powder resin has the potential for application at an industrial level.     

Preparation and enhanced properties of poly(propylene)/ silica‐grafted‐hyperbranched polyester nanocomposites

A series of poly(propylene) silica‐grafted‐hyperbranched polyester nanocomposites by grafting the modified hyperbranched polyester (Boltorn? H20), possessing theoretically 50% end carboxylic groups and 50% end hydroxyl groups, which endcapped with octadecyl isocyanate (C19), onto the surface of SiO₂ particles (30 nm) through 3‐glycidoxy‐propyltrimethoxysilane (GPTS) was prepared. The effect of silica‐grafted‐modified Boltorn? H20 on the mechanical properties of polypropylene (PP) was investigated by tensile and impact tests. The morphological structure of impact fracture surface and thermal behavior of the composites were determined by scanning electron microscopy (SEM) and differential scanning calorimetry (DSC), respectively. The melt viscosity of composites was investigated by melt flow index (MFI). The obtained results showed that: (1) the modified Boltorn? H20 was successfully grafted onto the SiO₂ surface confirmed by FT‐IR and X‐ray photoelectron spectroscopy (XPS) analysis; (2) the incorporation of silica‐grafted‐modified Boltorn? H20 (3–5 wt% SiO₂) greatly enhanced the notched impact strength as well the tensile strength of the composites; (3) the incorporation of silica‐grafted‐modified Boltorn? H20 had no influence on the melting temperature and crystallinity of PP phase; (4) the MFI of PP composites increased when the silica‐grafted‐modified Boltorn? H20 particles were added compared with PP/SiO₂ or PP/SiO₂‐GPTS composites. Copyright © 2004 John Wiley & Sons, Ltd.     

Melt spinning of bacterial aliphatic polyester using reactive extrusion for improvement of crystallization

This paper reports on an attempt to use reactive extrusion with peroxide as a comfortable pathway for improvement of the crystallization of poly(3-hydroxybutyrate) in a melt spinning process. At first, rheological and thermal properties of the modified melts are determined in order to assess the effect of nucleation. Then spinning tests are carried out. Molecular weights and molecular weight distributions of the spun fibers are determined by chromatographic methods. Average crystallite size is measured by wide angle X-ray scattering. Thermal and textile properties of the spun PHB fibers are also determined. An estimation of the improvement of the crystallization in the spinline and of the inhibition of the secondary crystallization in the fibers from the use of the described way of reactive extrusion is given.