Pt(110)/Sb电极上甲酸的电催化氧化特征和动力学

研究了Sb在Pt(110)晶面上不可逆吸附电化学特性及甲酸在Sb_ad修饰Pt(110)电极[Pt(110)/Sb]上的电催化氧化特征及其反应动力学.发现当扫描电位的上限E_u≤0.45V时,Sb_ad可稳定地吸附在Pt(110)表面上,从而有效地抑制了甲酸的解离吸附.与未修饰的Pt(110)上的结果相比,在Pt(110)/Sb上甲酸氧化的峰电位负移了0.35V.当θ_Sb=0.126时,Pt(110)/Sb电极对甲酸的电催化活性最高.还研究了Pt(110)/Sb上甲酸氧化反应的动力学,定量解析了不同θ_Sb下甲酸氧化的速度常数kf和传递系数β.     

Sb在Pt(100),Pt(110),Pt(111)及Pt(320)上不可逆吸附的电化学特性

研究了Sb在Pt(1 0 0 ) ,Pt(1 1 0 ) ,Pt(1 1 1 )和Pt(32 0 )单晶面上不可逆吸附的电化学特性 .发现当扫描电位的上限Eu≤ 0 .45V时 ,Sbad可以稳定地吸附在Pt(1 0 0 ) ,Pt(1 1 0 )和Pt(1 1 1 )表面 ,而Sbad在Pt(32 0 )表面稳定的电位较低 ,为Eu≤ 0 .40V .从饱和吸附Sb的铂单晶电极出发 ,通过改变电位扫描上限Eu 和电位扫描圈数可以获得不同Sb覆盖度 (θSb)的电极 .根据Sb和H在铂单晶电极表面共吸附的定量数据 ,对Sb在不同铂单晶面上饱和吸附的模型进行了初步探讨 .     

铂电极上锑吸附原子对1,2-丙二醇电催化氧化性能的影响

运用电化学循环伏安(CV)和电化学原位石英晶体微天平(EQCM)研究了Pt电极表面不可逆吸附Sb原子的电化学特性以及Pt电极上Sb吸附原子对0.1mol·L-1H2SO4溶液中1,2 丙二醇电催化氧化性能的影响.研究发现,当扫描电位的上限Eu≤0.50V(SCE)时,Sb可以稳定地吸附在Pt电极表面,饱和覆盖度为0.34;通过控制电位扫描上限和扫描圈数剥离部份Sb可方便地得到Sbad的不同覆盖度;Pt电极表面Sb吸附原子能在较低的电位下吸附氧,可显著提高1,2 丙二醇电催化氧化活性.与Pt电极相比较,Sb饱和吸附原子修饰的Pt电极使1,2 丙二醇氧化的峰电流增加了近2倍.作者还从表面质量变化提供了吸附原子电催化作用的新数据.     

In situ FTIRS studies of kinetics of HCOOH oxidation on Pt(110) electrode modified with antimony adatoms

The electrochemical behavior of irreversibly adsorbed antimony on a Pt(110) electrode (Pt(110)/Sb) with various coverages was studied using cyclic voltammetry. The kinetics of HCOOH oxidation via reactive intermediates on Pt(110)/Sb were investigated quantitatively by employing the potential step technique and in situ FTIR spectroscopy. The results demonstrated that Sb adatoms were stable on Pt(110) when the electrode potential was below 0.45 V (SCE). It has been revealed that the dissociative adsorption of formic acid can be inhibited by the presence of Sb_ad on the Pt(110) surface. The electrocatalytic effects of Sb_ad towards HCOOH oxidation consist in a negative shift of the oxidation potential (about 350 mV) and the enhancement of the oxidation current. Based on the data processing method of integration transform developed in our previous papers, the kinetics of HCOOH oxidation on Pt(110)/Sb electrodes of different θ_Sb have been investigated quantitatively, and both the rate constant k_f and the transfer coefficient β were determined and reported.     

Pt电极上Sb，S吸附原子对正丁醇电催化氧化性能的影响

运用电化学循环伏安和石英晶体微天平研究了0.1 mol/L H2SO4 溶液中正丁醇（1-BL）在Pt电极和以Sb，S吸附原子修饰的Pt（Pt/Sbad和Pt/Sad）电极上电催化氧化过程。从电极表面质量变化表明正丁醇的氧化与电极表面氧物种有着极其密切的关系。Pt电极表面Sb吸附原子能在较低的电位下吸附氧，可显著提高正丁醇电催化氧化活性。与Pt电极相比较，Sb吸附原子修饰的Pt电极使正丁醇氧化的峰电位负移了0.33 V，峰电流增大了近一倍。相反，Pt电极表面S吸附原子的氧化会消耗表面氧物种，抑制了正丁醇的电氧化。本文从表面质量变化提供了吸附原子电催化作用的新数据。     

Pt电极上吸附原子对仲丁醇电催化氧化性能的影响

运用电化学循环伏安和石英晶体微天平研究了HClO4溶液中仲丁醇在Pt电极及以Sb和S吸附原子修饰的Pt(Pt/Sbad和Pt/Sad)电极上的电催化氧化过程 .从电极表面质量变化可以看出 ,仲丁醇的氧化与电极表面的氧物种有着极其密切的关系 .Pt电极表面Sb吸附原子可在较低的电位下吸附氧 ,明显提高仲丁醇的氧化活性 .与Pt电极相比 ,Sb吸附原子修饰的Pt电极使仲丁醇氧化的峰电位负移约 10 0mV .相反 ,Pt电极表面S吸附原子的氧化会消耗表面氧物种 ,抑制仲丁醇的氧化 .从电极表面质量变化提供了吸附原子电催化作用的数据     

Pt及其修饰电极上甲醇吸附和氧化的CV和EQCM研究

运用电化学循环伏安和石英晶体微天平 (EQCM )研究了 0 .1mol·L- 1H2 SO4 溶液中甲醇在Pt电极和以Sb ,S不可逆吸附原子修饰的Pt(Pt/Sbad和Pt/Sad)电极上的吸附和氧化过程 .结果表明甲醇的氧化与电极表面氧物种有着极其密切的关系 .Pt电极表面Sb吸附原子能在较低的电位下吸附氧 ,可显著提高甲醇电催化氧化活性 .与Pt电极相比较 ,Sb吸附原子修饰的Pt电极使甲醇氧化的峰电位负移了 0 .13V .相反 ,Pt电极表面S吸附原子的氧化会消耗表面氧物种 ,抑制了甲醇的电氧化 .本文从表面质量变化提供了吸附原子电催化作用的新数据     

Pt和Sb、S吸附原子修饰的Pt电极上正丙醇氧化的CV和EQCM研究

运用电化学循环伏安法和石英晶体微天平研究了正丙醇在Pt电极和以Sb、S吸附原子修饰的Pt（Pt/Sbad和Pt/Sad）电极上的吸附和氧化过程.从电极表面质量变化角度指出正丙醇的氧化与电极表面氧物种有着极其密切的关系.Pt电极表面Sb吸附原子能在较低的电位下吸附氧，可显著提高正丙醇电催化氧化活性，与在Pt电极上相比较,正丙醇氧化的峰电位负移了0.29 V,峰电流增加了近2倍.相反,Pt电极表面S吸附原子的氧化会消耗表面氧物种，饱和吸附S原子的Pt电极上正丙醇的电氧化受到抑制.本文从表面质量变化提供了吸附原子电催化作用的新数据.     

碳载Pt/Sb_(ad)电极上乙醇电催化氧化特征和原位FTIR反射光谱研究

用电化学循环伏安法和原位 FTIR反射光谱法研究了 Sb在碳载纳米 Pt膜电极 (nm -Pt/ GC)表面不可逆吸附的电化学特性及酸性介质中乙醇的吸附和电催化氧化特性 .结果指出 ,当扫描电位的上限 Eu≤0 .5 0 V(SCE)时 ,Sbad可以稳定地吸附在 nm-Pt/ GC电极表面 .与未修饰的 nm-Pt/ GC电极上结果相比 ,Sbad修饰的 nm-Pt/ GC/ Sbad/ (nm-Pt/ GC)的催化活性显著增加 .测得当覆盖度θsb=0 .1 3 7时 ,修饰电极对乙醇的电催化活性最高 ,乙醇氧化的峰电位负移了 0 .1 5 V,峰电流增大了 1倍 .原位 FTIR反射光谱的结果从分子水平揭示了 Sb修饰对乙醇氧化反应途径的选择功能 .     

Manipulation of electrocatalytic reaction pathways through surface chemistry: in situ Fourier transform infrared spectroscopic studies of 1,3-butanediol oxidation on a Pt surface modified with Sb and S adatoms

Cyclic voltammetry and in situ Fourier transform infrared (FTIR) spectroscopy were employed to study the electrocatalytic properties of a Pt electrode modified with adatoms of antimony (Sb) or sulfur (S) for 1,3-butanediol (1,3-BD) oxidation. The results demonstrated the possibility of manipulating the reaction pathways involved in 1,3-BD oxidation through chemical modification of the Pt electrode surface. Both Sb and S adatoms (Sb(ad) and S(ad)) can inhibit the dissociative reaction of 1,3-BD into CO, which is the main source of self-poisoning in electrocatalysis of small organic molecules. On Pt electrodes modified with a high coverage of Sb(ad) (Pt/Sb(ad)) the onset oxidation potential of 1,3-BD has been significantly decreased, which is attributed to the fact that the oxidation of Sb(ad) occurs at lower potentials than that of the Pt surface. In situ FTIR results illustrated that, although at potentials below 0.5 V (vs a saturated calomel electrode), at which the Sb(ad) is stable on the Pt electrode surface, both carbonyl and CO2 species have been observed, the principal oxidation products of 1,3-BD are carbonyl species. Such results indicate that the reaction is mainly the dehydrogenation of 1,3-BD molecules. However, at potentials above 0.5 V the proportion of CO2 species in the oxidation products increases quickly, implying that the reaction has turned to the breakage of C-C bonds in 1,3-BD molecules and the subsequent oxidation of the cleaved fragments. In contrast with the cases of 1,3-BD oxidation on Pt and Pt/Sb(ad) electrodes, the reaction of 1,3-BD oxidation on a Pt electrode modified with S adatoms (Pt/S(ad)) is oriented completely to the production of carbonyl species when electrode potentials are below 0.9 V, though the reaction activity is relatively low. When the electrode potential is increased above 0.9 V, the intensity of the CO2 IR band in the FTIR spectra increases rapidly, corresponding to a fast oxidation of 1,3-BD on surface Pt sites recovered by the oxidation and desorption of S(ad) from the Pt surface.     

Pt及其修饰电极上乙醇吸附和氧化的CV和EQCM研究

运用电化学循环伏安和石英晶体微天平研究了乙醇在Pt电极和以Sb,S吸附原子修饰的Pt(Pt/Sbad和Pt/Sad)电极上的吸附和氧化过程。结果表明乙醇的氧化与电极表面氧物种有着极其密切的关系。Pt电极表面Sb吸附原子能在较低的电位下吸附氧,可显著提高乙醇电催化氧化活性。相反,Pt电极表面S吸附原子的氧化会消耗表面氧物种,抑制了乙醇的电氧化。本文从表面质量变化提供了吸附原子电催化作用的新数据。     

Electrocatalytic properties of Pt(111), Pt(332), Pt(331) and Pt(110) single crystal electrodes towards ethylene glycol oxidation in sulphuric acid solutions

In the present paper four platinum single crystal electrodes, two basal planes of Pt(111) and Pt(110) and two stepped surfaces of Pt(332) and Pt(331), were prepared and used in the study of electro-oxidation of ethylene glycol (EG). All of these Pt single crystal electrodes belong to the [1 0] zone of crystallography, and exhibit on their surface (111) symmetry sites or certain combinations of terraces of (111) symmetry with steps of (111) symmetry type. It has been found that as a result of a favourable steric matching of surface sites the Pt(110) electrode manifested a higher activity both for EG dissociative adsorption and oxidation than that of the Pt(111) electrode. The stepped surfaces of Pt(332) and Pt(331) operated with certain combinations of characteristics of Pt(111) and Pt(110). The best electrocatalytic properties have been obtained with a Pt(331) electrode, and this is attributed both to the configuration of the atomic arrangement and to the stability of this surface.In summary, the above results show that the performance of a given Pt single crystal electrode in EG oxidation at a potential below 1.0 V may be evaluated by three factors.

1. (1) The ability to resist self-poisoning (AB) which describes the difficulty of EG dissociative adsorption on the electrode surface.

2. (2) The activity for EG oxidation (AC). In considering that the threshold potential for EG oxidation on all electrodes is at 0.3 V and that the self-poisoning is encountered in PGPS, the activity for EG oxidation may be reasonably characterized by the intensity of the peak current acquired in NGPS near 0.6 V, which corresponds to the maximum current of EG oxidation on an activated (non-poisoned) surface of the electrode.

3. (3) The stability of activity during potential cycling (SA) between 0.05 and 1.0 V, which describes the resistance to the decrease of intensity of the EG oxidation current during voltammetric cycling.

For the two basal planes studied, the AB and SA of Pt(111) are higher than those of Pt(110), but its AC is much lower than that of Pt(110). These differences are clearly related to the surface atomic arrangement of the two electrodes. As has been discussed above, the surface of Pt(111) is atomically smooth and stable during voltammetric cycling. The surface of Pt(110) presents, however, atomic steps and is reconstructed under experimental conditions, i.e. certain steric configurations are encountered on the Pt(110) surface. The high AC and the low AB may be assigned to a favourite stereographic matching during EG adsorption and oxidation on Pt(110).The two electrodes with stepped surfaces, Pt(332) and Pt(331), contain different densities of (110) sites, which are formed on the border between terrace and step, as shown in Fig. 8. The AB of these two electrodes has been observed at a moderate range between that of Pt(111) and the AB of Pt(110). With a majority of (111) sites on its surface, the electrode of Pt(332) operates at a relatively higher AC than Pt(111) does, and its SA is not as good as that of Pt(111) but is much better than the SA of a Pt(110) electrode. In all cases the highest AC and SA are obtained with a Pt(331) electrode. It may be seen from the profile of a (331) plane (shown by the cross-section of A-A in Fig. 8) that all atoms on the top of the surface participated in forming (110) sites, and the atom on the step has two functions — one is to form a (110) site with an atom located in the terrace of second layer and the other is to form a (111) site in the terrace of the same layer. It has been mentioned in the above discussions that the Pt(110) electrode keeps a higher AC due to favourite stereographic matching in EG adsorption and oxidation, but its SA is the worst, due to the instability of the surface. The highest AC and SA obtained with Pt(331) may be ascribed not only to the high density of (110) sites existing on the surface, but also to the stabilization of these (110) sites, and moreover, the synergy generated by the atomic arrangement of the Pt(331) surface may also contribute to the performance of the Pt(331) electrode.     

Methodical aspects of studying the electroreduction of nitrate on modified single crystal Pt(hkl) + Cu electrodes

Technique of modification of basal faces Pt(hkl) by adatoms and epitaxial copper deposits is developed. Analysis of potentiostatic current transients of copper deposition/dissolution and atomic force microscopy showed that the activity of Pt(hkl) faces regarding the processes of copper nucleation and epitaxial growth increases in the sequence of Pt(111) < Pt(110) < Pt(100). The reaction of nitrate anion reduction is sensitive towards the surface structure, not only in the case of platinum, but also in the case of copper deposits (including a monolayer of adatoms). The highest process rate is observed for the Pt(100) electrode modified by a monolayer of adatoms or islands of bulk copper; nitrate reduction at the lowest rate occurs at Pt(111) + Cu electrodes. Structure-sensitive competitive adsorption of background electrolyte and nitrate anions is the factor that largely determines the kinetics of nitrate reduction on different faces of platinum single crystal and copper deposits.     

A versatile electroless approach to controlled modification of Sb on Pt surfaces towards efficient electrocatalysis of formic acid

A new facile approach towards developing superior Pt-based catalysts for HCOOH electrooxidation has been proposed, which is exemplified with a mimetic underpotential deposition (MUPD) of Sb on Pt surfaces to attain a favorable coverage. Suitable Sb modification was achieved simply through immersing a bulk Pt electrode or dispersing Pt/C powders in a Sb(III) solution mixed with ascorbic acid (AA). AA serves as the mild reducing agent to ensure freshly reduced Pt surfaces for Sb modification, as demonstrated by the negatively shifted open circuit potential. The catalytic activity towards HCOOH electrooxidation on the above Sb-modified Pt/C catalyst far exceeds that on commercial Pt–Ru/C or Sb-modified Pt/C through traditional irreversible adsorption. This electroless approach is generally applicable to all types of Pt surfaces, in particular suited for upgrading Pt/C for practical anode catalysts of direct formic acid fuel cells.     

Enhancement of the electrochemical reduction of oxygen at platinum by nickel underpotential deposition

Polycrystalline Pt electrode was modified by underpotential deposition (upd) of nickel. The modification was performed by potential cycling in phosphate buffer pH 7. 0 containing NiSO₄, in which hydrogen and nickel upd processes were well separated. The maximum Ni upd coverage was found to be 0.3. Oxygen reduction was studied at bare and nickel upd-modified Pt. It was found that the reaction rate increased with increasing Ni upd coverage. At θ(Ni)=0.3, the current density was a factor of 2 higher compared to bare Pt (at the potential of 0.85 V). The capacitance of the electrode interface was determined in potential-relaxation experiments following interruption of the polarization current. It was found that the pseudocapacitance owing to a coverage by the adsorbed reaction intermediates was higher on the Ni-modified Pt surface than on bare Pt, which resulted in higher reaction rate. The influence of Ni adatoms on the surface coverage by the reaction intermediates was attributed to the inhibition of OH adsorption on Pt by OH ligands attached on neighboring Ni atoms.     

Products of SO2 adsorption on fuel cell electrocatalysts by combination of sulfur K-edge XANES and electrochemistry

Electrochemical adsorption of SO(2) on platinum is complicated by the change in sulfur oxidation state with potential. Here, we attempt to identify SO(2) adsorption products on catalyst coated membranes (CCMs) at different electrode potentials using a combination of in situ sulfur K-edge XANES (X-ray absorption near-edge structure) spectroscopy and electrochemical techniques. CCMs employed platinum nanoparticles supported on Vulcan carbon (Pt/VC). SO(2) was adsorbed from a SO(2)/N(2) gas mixture while holding the Pt/VC-electrode potential at 0.1, 0.5, 0.7, and 0.9 V vs a reversible hydrogen electrode (RHE). Sulfur adatoms (S(0)) are identified as the SO(2) adsorption products at 0.1 V, while mixtures of S(0), SO(2), and sulfate/bisulfate ((bi)sulfate) ions are suggested as SO(2) adsorption products at 0.5 and 0.7 V. At 0.9 V, SO(2) is completely oxidized to (bi)sulfate ions. The identity of adsorbed SO(2) species on Pt/VC catalysts at different electrode potentials is confirmed by modeling of XANES spectra using FEFF8 and a linear combination of experimental spectra from sulfur standards. Results on SO(2) speciation gained from XANES are used to compare platinum-sulfur electronic interactions for Pt(3)Co/VC versus Pt/VC catalysts in order to understand the difference between the two catalysts in terms of SO(2) contamination.     

Kinetics and mechanism of nitrate and nitrite electroreduction on Pt(100) electrodes modified by copper adatoms

Kinetics and mechanism of nitrate and nitrite reduction on Pt(100) electrode modified by Cu adatoms have been studied in solutions of sulfuric and perchloric acids by means of cyclic voltammetry and in situ IR-spectroscopy. It has been shown that the surface redox process with participation of ammonia or hydroxylamine at 0.5–0.9 V occurs only on the Cu-free platinum. The causes of this effect could be low adsorption energy of nitrate reduction products on copper or changes in the composition of the products (ammonia for Pt(100) and N₂O for Pt(100)+Cu). Nitrate reduction on Pt(100)+Cu electrode is much faster in the perchloric acid solution (by several orders of magnitude) as compared with unmodified platinum as a result of induced adsorption of nitrate anions in the presence of partly charged Cu atoms. In the solutions of sulfuric acid the rate of nitrate reduction is considerably lower as copper adatoms facilitate adsorption of sulfate anions, which block the adsorption sites for the nitrate.     

Sb在Au电极上不可逆吸附的电化学过程

用电化学循环伏安法和电化学石英晶体微天平(EQCM)技术研究了Sb在Au电极上不可逆吸附的电化学过程. 研究结果表明, 在-0.25 V到0.18 V(vs SCE)范围内, Sb可在Au电极上稳定吸附, 并且在0.15 V附近出现特征氧化还原峰. 根据EQCM实验数据, 在电位0.18 V时, Sb在Au电极上的氧化产物是Sb2O3; 同时Sb的吸附阻止了电解液中阴离子和水在Au电极上的吸附. 当电极电位超过0.20 V时, Sb2O3会被进一步氧化成Sb5+化合物, 同时逐渐从Au电极表面脱附.     

Electrochemical and FTIRS characterisation of NO adlayers on cyanide-modified Pt(111) electrodes: the mechanism of nitric oxide electroreduction on Pt

We report here a study, using cyclic voltammetry and FTIRS, of NO irreversibly adsorbed on a cyanide-modified Pt(111) electrode. NO adlayers were formed by immersion of the cyanide-modified Pt(111) electrode in an acidic solution of KNO(2). The behaviour of NO adsorbed on the cyanide-modified electrode is very similar to that of NO on the clean Pt(111) surface, suggesting that adsorbed cyanide (saturation coverage theta(CN) = 0.5) behaves simply as a third body, blocking some of the surface sites but leaving the free Pt sites unaffected. Comparison of the voltammetric profile for NO electroreduction on Pt(111) and on cyanide-modified Pt(111) electrodes has allowed us: (i) to confirm that the reduction of three-fold hollow NO and atop NO on Pt(111) electrodes occurs in two distinct reduction peaks, as previously proposed by Rosca et al. (Langmuir, 2005, 21, 1448); (ii) to suggest that the reduction of irreversibly adsorbed NO layers on Pt electrodes can proceed through two possible paths, one involving an EE mechanism in which the rate-determining step (rds) is an Eley-Rideal reaction, with a direct proton transfer from the solution to adsorbed NO, and the other involving an EC mechanism in which the rds is a Langmuir-Hinshelwood reaction of adsorbed NO with adsorbed H. The availability of adsorbed hydrogen determines which path is followed by the reaction; (iii) to identify the smallest atomic ensemble for the reduction of NO on Pt as being composed of two adjacent Pt atoms.     

甲醇在欠电位沉积Sn/Pt电极上催化氧化

在欠电位沉积（upd）锡修饰的铂电极（upd-Sn/Pt）上,对甲醇电化学催化氧化过程进行了研究.发现当Pt表面upd-Sn的覆盖率在20％附近时,对甲醇的催化氧化的增强作用最为明显；在电位低于0.35 V （vs RHE）时,甲醇在Pt与upd-Sn/Pt电极上氧化只进行到脱氢生成CO的步骤;在0.35 V以后,表面Sn－OH形成,反应Sn－OH＋COads=Sn＋CO2＋H＋＋e有利于表面CO的去除;而Pt电极上,只有0.6 V以后,才有反应Pt－OH＋COads=Pt＋CO2＋H＋＋e发生.因此,Sn的存在有利于甲醇在较低的电位下氧化; Pt电极上CH3OH脱氢并释放出电子的过程是一个快速的过程,表面CO的去除是甲醇氧化过程的控制步骤;甲醇氧化产生的表面吸附态CO 以线式吸附为主,少量的桥式吸附态CO在反应初期即达到吸附饱和; Pt表面上upd-Sn表现的催化增强作用,在光亮铂电极和在高分散铂黑电极上是一致的.