Lateral Force Microscopy Study of the Friction between Silica Surfaces

The friction between a single silica glass sphere and a flat silica glass surface has been investigated using lateral force microscopy. Two types of silica surface were investigated, one fully hydroxylated and the other partially dehydroxlated. These samples have markedly different wetting properties and are known as hydrophilic and hydrophobic silica, respectively. The lateral friction force as a function of applied normal load has been collected for five different-sized spheres for both surface types. Analysis of the friction versus load data indicates that the hydrophilic surfaces have a molecularly smooth contact. For the hydrophobic surfaces, it is not clear whether the friction-load response is caused by a smooth or an asperity-dominated contact zone. Copyright 2000 Academic Press.     

Molecular modeling of oligopeptide adsorption onto functionalized quartz surfaces

The adsorption of an EAK 16-II oligopeptide sequence in aqueous medium onto functionalized quartz surfaces has been studied by using force field calculations and molecular dynamics methods. Two different surfaces have been simulated respectively involving fully methylated and fully silanolic quartz surfaces. Geometry optimization and molecular dynamics simulations showed that the adsorption process is mainly governed by the electrostatic interactions between SiO- surface groups and the charged residues of the oligopeptide sequence. In particular, it was found that strong electrostatic interactions (a) prompt the parallel orientation of the oligopeptide with respect to the hydrophilic charged surface, resulting in an effective physisorption process and (b) stabilize the beta-sheet configuration of the physisorbed molecules. In particular, the end-on oligopeptide orientations are demonstrated to progressively lie back onto the hydrophilic surface, but this does not happen onto the hydrophobic surface. In any case, no physisorption process was observed for the fully methylated surface, where the molecule is seen to move away from the surface during the simulation time.     

Molecular packing of lysozyme,fibrinogen, and bovine serum albumin on hydrophilic and hydrophobic surfaces studied by infrared-visible sum frequency generation and fluorescence microscopy

Infrared-visible sum frequency generation (SFG) vibrational spectroscopy, in combination with fluorescence microscopy, was employed to investigate the surface structure of lysozyme, fibrinogen, and bovine serum albumin (BSA) adsorbed on hydrophilic silica and hydrophobic polystyrene as a function of protein concentration. Fluorescence microscopy shows that the relative amounts of protein adsorbed on hydrophilic and hydrophobic surfaces increase in proportion with the concentration of protein solutions. For a given bulk protein concentration, a larger amount of protein is adsorbed on hydrophobic polystyrene surfaces compared to hydrophilic silica surfaces. While lysozyme molecules adsorbed on silica surfaces yield relatively similar SFG spectra, regardless of the surface concentration, SFG spectra of fibrinogen and BSA adsorbed on silica surfaces exhibit concentration-dependent signal intensities and peak shapes. Quantitative SFG data analysis reveals that methyl groups in lysozyme adsorbed on hydrophilic surfaces show a concentration-independent orientation. However, methyl groups in BSA and fibrinogen become less tilted with respect to the surface normal with increasing protein concentration at the surface. On hydrophobic polystyrene surfaces, all proteins yield similar SFG spectra, which are different from those on hydrophilic surfaces. Although more protein molecules are present on hydrophobic surfaces, lower SFG signal intensity is observed, indicating that methyl groups in adsorbed proteins are more randomly oriented as compared to those on hydrophilic surfaces. SFG data also shows that the orientation and ordering of phenyl rings in the polystyrene surface is affected by protein adsorption, depending on the amount and type of proteins.     

Adsorption of simple fluid on silica surface and nanopore: effect of surface chemistry and pore shape

This paper reports a molecular simulation study on the adsorption of simple fluids (argon at 77 K) on hydroxylated silica surfaces and nanopores. The effect of surface chemistry is addressed by considering substrates with either partially or fully hydroxylated surfaces. We also investigate the effect of pore shape on adsorption and capillary condensation by comparing the results for cylindrical and hexagonal nanopores having equivalent sections (i.e., equal section areas). Due to the increase in the polarity of the surface with the density of OH groups, the adsorbed amounts for fully hydroxylated surfaces are found to be larger than those for partially hydroxylated surfaces. Both the adsorption isotherms for the cylindrical and hexagonal pores conform to the typical behavior observed in the experiments for adsorption/condensation in cylindrical nanopores MCM-41. Capillary condensation occurs through an irreversible discontinuous transition between the partially filled and the completely filled configurations, while evaporation occurs through the displacement at equilibrium of a hemispherical meniscus along the pore axis. Our data are also used to discuss the effect of surface chemistry and pore shape on the BET method. The BET surface for fully hydroxylated surfaces is much larger (by 10-20%) than the true geometrical surface. In contrast, the BET surface significantly underestimates the true surface when partially hydroxylated surfaces are considered. These results suggest that the surface chemistry and the choice of the system adsorbate/adsorbent is crucial in determining the surface area of solids using the BET method.     

In situ adsorption studies of a 14-amino acid leucine-lysine peptide onto hydrophobic polystyrene and hydrophilic silica surfaces using quartz crystal microbalance, atomic force microscopy, and sum frequency generation vibrational spectroscopy

The adsorption of a 14-amino acid amphiphilic peptide, LK14, which is composed of leucine (L, nonpolar) and lysine (K, charged), on hydrophobic polystyrene (PS) and hydrophilic silica (SiO2) was investigated in situ by quartz crystal microbalance (QCM), atomic force microscopy (AFM), and sum frequency generation (SFG) vibrational spectroscopy. The LK14 peptide, adsorbed from a pH 7.4 phosphate-buffered saline (PBS) solution, displayed very different coverage, surface roughness and friction, topography, and surface-induced orientation when adsorbed onto PS versus SiO2 surfaces. Real-time QCM adsorption data revealed that the peptide adsorbed onto hydrophobic PS through a fast (t < 2 min) process, while a much slower (t > 30 min) multistep adsorption and rearrangement occurred on the hydrophilic SiO2. AFM measurements showed different surface morphologies and friction coefficients for LK14 adsorbed on the two surfaces. Surface-specific SFG spectra indicate very different ordering of the adsorbed peptide on hydrophobic PS as compared to hydrophilic SiO2. At the LK14 solution/PS interface, CH resonances corresponding to the hydrophobic leucine side chains are evident. Conversely, only NH modes are observed at the peptide solution/SiO2 interface, indicating a different average molecular orientation on this hydrophilic surface. The surface-dependent difference in the molecular-scale peptide interaction at the solution/hydrophobic solid versus solution/hydrophilic solid interfaces (measured by SFG) is manifested as significantly different macromolecular-level adsorption properties on the two surfaces (determined via AFM and QCM experiments).     

Structure and dynamics of liquid methanol confined within functionalized silica nanopores

Molecular dynamics simulations have been carried out to investigate the structure and dynamics of liquid methanol confined in 3.3 nm diameter cylindrical silica pores. Three cavities differing in the characteristics of the functional groups at their walls have been examined: (i) smooth hydrophobic pores in which dispersive forces prevail, (ii) hydrophilic cavities with surfaces covered by polar silanol groups, and (iii) a much more rugged pore in which 60% of the previous interfacial hydroxyl groups were replaced by the bulkier trimethylsilyl ones. Confinement promotes a considerable structure at the vicinity of the pore walls which is enhanced in the case of hydroxylated surfaces. Moreover, in the presence of the trimethylsilyl groups, the propagation of this interface-induced spatial ordering extends down to the central region of the pore. Concerning the dynamical modes, we observed an overall slowdown in both the translational and rotational motions. An analysis of these mobilities from a local perspective shows that the largest retardations operate at the vicinity of the interfaces. The gross features of the rotational dynamics were analyzed in terms of contributions arising from bulk and surface states. Compared to the bulk dynamical behavior, the characteristic timescales associated with the rotational motions show the most dramatic increments. A dynamical analysis of hydrogen bond formation and breaking processes is also included.     

DFT study of the adsorption of microsolvated glycine on a hydrophilic amorphous silica surface

Density functional theory (DFT) periodic ab initio molecular dynamics calculations are used to study the adsorption of gaseous and microsolvated glycine on a hydroxylated, hydrophilic silica surface. The silica model is presented and the interaction of water with surface silanols is studied. The heat of interaction of water is higher with the associated silanols (be they terminal or geminal ones) studied here than with isolated silanols presented in past works. Glycine is stabilized in a parallel mode on the hydroxylated surface. Terminal silanols do not allow the stabilization of the zwitterionic form, whereas geminal silanols do. Molecular dynamics (MD) first-principle calculations show that microsolvated zwitterion glycine directly binds through the carboxylate function to a surface silanol rather than through water molecules. The adsorption mode, whether with or without additional water molecules, is parallel to the surface. The ammonium function does not interact directly with the silanol groups but rather through water molecules. Thus, the carboxylate and ammonium functions exhibit two different reactivities towards silanols. The calculated free energies, taking into account the chemical potentials of water and glycine in the gas phase, suggest the existence of a thermodynamic domain in which the glycine is present in the gas phase as well as strongly adsorbed on specific sites of the surface.     

Mobility of single DNA chain under electric field during its transient contact with solid surfaces

The motion of DNA chain under electric field when it is in transient contact with the solid surfaces in aqueous solution was studied by single molecule fluorescence microscopy at the total internal reflection geometry (TIRFM). In situ observation discovered that single λ-DNA chains driven by electric field made transient contact with the solid surface and made hitting–sliding–leaving-like motion along the surface. By varying the surface chemistry, from the negative-charged silanol group-rich surface to positive-charged amino group-rich surface, as well as hydrophobic surfaces, the dependence of DNA mobility on the surface–DNA interaction was studied. The results show that a dependence of the mobility of DNA on the surface polarity with respect to DNA itself. The study on different surfaces rich of silanol, amide, amino, and methyl groups show a sequence of DNA mobility of silanol > amide > amino. The mobility of DNA on methyl terminated surface was found to be similar to that on amino surface. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2541–2546, 2009     

Bond-strengthening in staphylococcal adhesion to hydrophilic and hydrophobic surfaces using atomic force microscopy

Time-dependent bacterial adhesion forces of four strains of Staphylococcus epidermidis to hydrophobic and hydrophilic surfaces were investigated. Initial adhesion forces differed significantly between the two surfaces and hovered around -0.4 nN. No unambiguous effect of substratum surface hydrophobicity on initial adhesion forces for the four different S. epidermidis strains was observed. Over time, strengthening of the adhesion forces was virtually absent on hydrophobic dimethyldichlorosilane (DDS)-coated glass, although in a few cases multiple adhesion peaks developed in the retract curves. Bond-strengthening on hydrophilic glass occurred within 5-35 s to maximum adhesion forces of -1.9 +/- 0.7 nN and was concurrent with the development of multiple adhesion peaks upon retract. Poisson analysis of the multiple adhesion peaks allowed separation of contributions of hydrogen bonding from other nonspecific interaction forces and revealed a force contribution of -0.8 nN for hydrogen bonding and +0.3 nN for other nonspecific interaction forces. Time-dependent bacterial adhesion forces were comparable for all four staphylococcal strains. It is concluded that, on DDS-coated glass, the hydrophobic effect causes instantaneous adhesion, while strengthening of the bonds on hydrophilic glass is dominated by noninstantaneous hydrogen bond formation.     

Chemical Force Microscopy Study of Adhesion and Friction between Surfaces Functionalized with Self-Assembled Monolayers and Immersed in Solvents

Adhesive and frictional forces between surfaces modified with self-assembled monolayers (SAMs) and immersed in solvents were measured with chemical force microscopy as functions of surface functionality and solvent. Si/SiO2 substrates were modified with SAMs of alkylsiloxanes (SiCl3(CH2)n-X), and gold-coated AFM tips were modified with SAMs of alkylthiolates (HS-(CH2)n-X). SAMs of alkylsiloxanes terminated in a methyl or oxidized vinyl group; SAMs of alkanethiolates terminated in a methyl or carboxyl group. Adhesive and frictional forces were measured in hexadecane, ethanol, 1,2-propanediol, 1,3-propanediol, and water. The work of adhesion (W) was calculated with the Johnson-Kendall-Roberts theory of adhesive contact. The JKR values agreed well with values derived from the Fowkes-van Oss-Chaudhury-Good surface tension model and from contact angle results. Calculated values of W for all combinations of contacting surfaces and solvents spanned two orders of magnitude. W correlated with the surface tension of the solvent for hydrophobic/hydrophobic interactions; hydrophilic/hydrophilic and hydrophobic/hydrophilic interactions were more complex. Friction forces were fit to a modified form of Amonton's law. For any solvent, friction coefficients were largest for the hydrophilic/hydrophilic contacting surfaces. The friction coefficient for any contacting pair was largest in hexadecane. In polar solvents, friction coefficients scaled with solvent polarity only for hydrophobic/hydrophobic contacting pairs. Copyright 1999 Academic Press.     

Mucin-electrolyte interactions at the solid-liquid interface probed by QCM-D

The interaction between mucin and ions has been investigated by employing the quartz crystal microbalance technique with measurement of energy dissipation. The study was partially aimed at understanding the adsorption of mucin on surfaces with different chemistry, and for this purpose, surfaces exposing COOH, OH, and CH(3) groups were prepared. Mucin adsorbed to all three types of functionalized gold surfaces. Adsorption to the hydrophobic surface and to the charged hydrophilic surface (COOH) occured with high affinity despite the fact that in the latter case both mucin and the surface were negatively charged. On the uncharged hydrophilic surface exposing OH groups, the adsorption of mucin was very low. Another aim was to elucidate conformational changes induced by electrolytes on mucin layers adsorbed on hydrophobic surfaces from 30 mM NaNO(3). To this end, we investigated the effect of three electrolytes with increasing cation valance: NaCl, CaCl(2) and LaCl(3). At low NaCl concentrations, the preadsorbed layer expands, whereas at higher concentrations of NaCl the layer becomes more compact. This swelling/compacting of the mucin layer is fully reversible for NaCl. When the mucin layer instead is exposed to CaCl(2) or LaCl(3), compaction is observed at 1 mM. For CaCl(2), this process is only partially reversible, and for LaCl(3), the changes are irreversible within the time frame of the experiment. Finally, mucin interaction with the DTAB cationic surfactant in an aqueous solution of different electrolytes was evaluated with turbidimetry measurements. It is concluded that the electrolytes used in this work screen the association between mucin and DTAB and that the effect increases with increasing cation valency.     

Effect of surface polarity on water contact angle and interfacial hydration structure

We perform molecular dynamics simulations of water in the presence of hydrophobic/hydrophilic walls at T = 300 K and P = 0 GPa. For the hydrophilic walls, we use a hydroxylated silica model introduced in previous simulations [Lee, S. H.; Rossky, P. J. J. Chem. Phys. 1994, 100, 3334. Giovambattista, N.; Rossky, P. J.; Debenedetti, P. G.; Phys. Rev. E 2006, 73, 041604.]. By rescaling the physical partial atomic charges by a parameter 0 相似文献   

Electrokinetic properties of methylated quartz capillaries

Electrokinetic (zeta)-potentials of methylated (trimethylchlorosilane) quartz capillaries (5-6 microm in radius) were determined in 10(-4) M KCl solution. Over the course of time, the absolute values of the zeta-potential decrease, as a result of the formation of small bubbles on the rough methylated surface, generated from the flowing, nitrogen gas-saturated solution. This decrease is attributed to screening of a part of the solid surface. After the passage of time, a sharp increase in the zeta-potentials was observed, as the pressure was increased and the initial potential values were recovered. Sometimes, oscillations in the zeta-potentials were observed. This behaviour was explained by detachment of bubbles from the methylated surfaces by the flowing solution. Addition of non-ionic surfactant, which made the methylated surface hydrophilic, decreased the measured zeta-potentials. This was attributed to suppression of water slippage, an effect known to occur for hydrophobic solid surfaces. A mixed mechanism of charge formation is characteristic for these methylated quartz surfaces and is connected with presence of hydrophobic and hydrophilic areas. The ratio between these areas controls both the formation of surface charge as well as the contact angles.     

Molecular dynamics simulations of the adsorption of bone morphogenetic protein-2 on surfaces with medical relevance

Bone morphogenetic protein-2 (BMP-2) plays a crucial role in osteoblast differentiation and proliferation. Its effective therapeutic use for ectopic bone and cartilage regeneration depends, among other factors, on the interaction with the carrier at the implant site. In this study, we used classical molecular dynamics (MD) and a hybrid approach of steered molecular dynamics (SMD) combined with MD simulations to investigate the initial stages of the adsorption of BMP-2 when approaching two implant surfaces, hydrophobic graphite and hydrophilic titanium dioxide rutile. Surface adsorption was evaluated for six different orientations of the protein, two end-on and four side-on, in explicit water environment. On graphite, we observed a weak but stable adsorption. Depending on the initial orientation, hydrophobic patches as well as flexible loops of the protein were involved in the interaction with graphite. On the contrary, BMP-2 adsorbed only loosely to hydrophilic titanium dioxide. Despite a favorable interaction energy between protein and the TiO(2) surface, the rapid formation of a two-layer water structure prevented the direct interaction between protein and titanium dioxide. The first water adlayer had a strong repulsive effect on the protein, while the second attracted the protein toward the surface. For both surfaces, hydrophobic graphite and hydrophilic titanium dioxide, denaturation of BMP-2 induced by adsorption was not observed on the nanosecond time scale.     

Non-DLVO silica interaction forces in NMP-water mixtures. II. An asymmetric system

The interaction between energetically asymmetric hydrophilic and hydrophobic surfaces has fundamental and practical importance in both industrial and natural colloidal systems. The interaction forces between a hydrophilic silica sphere and a silanated, hydrophobic glass plate in N-methyl-2-pyrrolidone (NMP)-water binary mixtures were measured using atomic force microscopy (AFM). A strong and long-range attractive force was observed in pure water and was attributed to the formation of capillary bridges associated with nanoscale bubbles initially present on the hydrophobic surface. When NMP was added, the capillary force and corresponding pull-off force became less attractive, which was explained readily in terms of the surface wettability by the binary solvent mixture. Similar to the case of symmetric (two hydrophilic) surfaces, the range of attraction between the asymmetric surfaces was maximized at around 30 vol % NMP, which is consistent with the formation of a thick adsorbed macrocluster layer on the hydrophilic silica surface.     

Using colloid lithography to fabricate silicon nanopillar arrays on silicon substrates

In this study, we partially grafted geminal silanol groups in the protecting organic shells on the surfaces of gold nanoparticles (AuNPs) and then assembled the alkyl-AuNP-Si(OH)(4) particles onto the surfaces of silicon (Si) wafers. The density of assembled AuNPs on the Si surface was adjusted by varying the geminal silanol group content on the AuNP surface; at its optimal content, it approached the high assembly density (0.0254 particles/nm(2)) of an AuNP assembled monolayer. Using reactive-ion etching (RIE) with the templates as masks, we transferred the patterned AuNP assemblies to form large-area, size-tunable, Si nanopillar arrays, the assembly density of which was controlled by the dimensions of the AuNPs. Using this colloidal lithography (CL) process, we could generate Si nanopillars having sub-10-nm diameters and high aspect ratios. The water contact angles of the high-aspect-ratio Si nanopillars approached 150°. We used another fabrication process, involving electron beam lithography and oxygen plasma treatment, to generate hydrophilic 200-nm-resolution line patterns on a Si surface to assemble the AuNPs into 200-nm-resolution dense lines for use as an etching mask. Subsequent CL provided a patterned Si nanopillar array having a feature size of 200 nm on the Si surface. Using this approach, it was possible to pattern sub-10-nm Si nanopillar arrays having densities as high as 0.0232 nm(-2).     

The hydrophobic effect: molecular dynamics simulations of water confined between extended hydrophobic and hydrophilic surfaces

Structural and dynamic properties of water confined between two parallel, extended, either hydrophobic or hydrophilic crystalline surfaces of n-alkane C(36)H(74) or n-alcohol C(35)H(71)OH, are studied by molecular dynamics simulations. Electron density profiles, directly compared with corresponding experimental data from x-ray reflectivity measurements, reveal a uniform weak de-wetting characteristic for the extended hydrophobic surface, while the hydrophilic surface is weakly wetted. These microscopic data are consistent with macroscopic contact angle measurements. Specific water orientation is present at both surfaces. The ordering is characteristically different between the surfaces and of longer range at the hydrophilic surface. Furthermore, the dynamic properties of water are different at the two surfaces and different from the bulk behavior. In particular, at the hydrophobic surface, time-correlation functions reveal that water molecules have characteristic diffusive behavior and orientational ordering due to the lack of hydrogen bonding interactions with the surface. These observations suggest that the altered dynamical properties of water in contact with extended hydrophobic surfaces together with a partial drying of the surfaces are more indicative of the hydrophobic effect than structural ordering, which we suggest to be independent of surface topology.     

Structure and stability of the (001) alpha-quartz surface

The structure and surface energies of the cleaved, reconstructed, and fully hydroxylated (001) alpha-quartz surface of various thicknesses are investigated with periodic density functional theory (DFT). The properties of the cleaved and hydroxylated surface are reproduced with a slab thickness of 18 atomic layers, while a thicker 27-layer slab is necessary for the reconstructed surface. The performance of the hybrid DFT functional B3LYP, using an atomic basis set, is compared with the generalised gradient approximation, PBE, employing plane waves. Both methodologies give similar structures and surface energies for the cleaved and reconstructed surfaces, which validates studying these surfaces with hybrid DFT. However, there is a slight difference between the PBE and B3LYP approach for the geometry of the hydrogen bonded network on the hydroxylated surface. The PBE adsorption energy of CO on a surface silanol site is in good agreement with experimental values, suggesting that this method is more accurate for hydrogen bonded structures than B3LYP. New hybrid functionals, however, yield improved weak interactions. Since these functionals also give superior activation energies, we recommend applying the new functionals to contemporary issues involving the silica surface and adsorbates on this surface.     

Pseudomonas aeruginosa attachment on QCM-D sensors: the role of cell and surface hydrophobicities

While biofilms are ubiquitous in nature, the mechanism by which they form is still poorly understood. This study investigated the process by which bacteria deposit and, shortly after, attach irreversibly to surfaces by reorienting to create a stronger interaction, which leads to biofilm formation. A model for attachment of Pseudomonas aeruginosa was developed using a quartz crystal microbalance with dissipation monitoring (QCM-D) technology, along with a fluorescent microscope and camera to monitor kinetics of adherence of the cells over time. In this model, the interaction differs depending on the force that dominates between the viscous, inertial, and elastic loads. P. aeruginosa, grown to the midexponential growth phase (hydrophilic) and stationary phase (hydrophobic) and two different surfaces, silica (SiO(2)) and polyvinylidene fluoride (PVDF), which are hydrophilic and hydrophobic, respectively, were used to test the model. The bacteria deposited on both of the sensor surfaces, though on the silica surface the cells reached a steady state where there was no net increase in deposition of bacteria, while the quantity of cells depositing on the PVDF surface continued to increase until the end of the experiments. The change in frequency and dissipation per cell were both positive for each overtone (n), except when the cells and surface are both hydrophilic. In the model three factors, specifically, viscous, inertial, and elastic loads, contribute to the change in frequency and dissipation at each overtone when a cell deposits on a sensor. On the basis of the model, hydrophobic cells were shown to form an elastic connection to either surface, with an increase of elasticity at higher overtones. At lower overtones, hydrophilic cells depositing on the hydrophobic surface were shown to also be elastic, but as the overtone increases the connection between the cells and sensor becomes more viscoelastic. In the case of hydrophilic cells interacting with the hydrophilic surface, the connection is viscous at each overtone measured. It could be inferred that the transformation of the viscoelasticity of the cell-surface connection is due to changes in the orientation of the cells to the surface, which allow the bacteria to attach irreversibly and begin biofilm formation.     

硅胶自溶液中吸附胆固醇和卵磷脂

卵磷脂和胆固醇是细胞膜的主要组成,它们在不同界面上的定向排列方式对细胞膜的结构与功能起着重要的作用。用固体物质自非水溶剂中吸附类脂化合物形成类脂单层,再自水溶液中吸附蛋白质,可制成固体载体上的模拟生物膜。在固体表面上的类脂单层膜中类脂分子的定向方式与溶剂和固体表面性质有关。这些研究大多数是以非孔性物质为吸附剂(如aerosil,石墨化炭黑,carbochrom.等)自有机溶剂中吸附类脂化合物(主要是胆固醇和卵磷脂),根据单层饱和吸附时分子占据的面积推算单层中类脂化合物分子的取向。实际应用的吸附剂大多是孔性的,因此研究类脂化合物在孔性吸附剂(如,硅胶、活性炭等)上的吸附机理更有实际意义。