Enantioselective sequential-injection chemiluminescence immunoassays for 3,3′,5-triiodothyronine (T3) and thyroxine (T4)

This study deals with the development of enantioselective flow-through immunosensors for triiodothyronine (T₃) and tetraiodothyronine (thyroxine, T₄) on the basis of a competitive assay using enantioselective antibodies. The instrumental set-up is based on a simple sequential-injection system equipped with a chemiluminescence detector and an immunoreactor, which consists of a flow-cell packed with immobilized haptens. As haptens, 4-amino-l-phenylalanine (4-amino-l-Phe), 4-amino-d-Phe or l-T₃ were used. Antibodies directed against 4-amino-l- or d-Phe or l-T₃ were labeled with an acridinium ester. Three different approaches for immobilizing the haptens were investigated including simple adsorption on polystyrene, chemical binding to an activated methacrylate polymer and binding via the biotin-streptavidin binding (BSB) system. The latter approach showed the best results regarding repeatability and sensivity. Using biotinylated l-T₃ immobilized onto a streptavidin-derivatized trisacryl support and labeled anti-l-T₃ antibodies, a detection limit of 15.5 fmol/ml for l-T₃ was obtained. One assay cycle including regeneration takes only about 5 min. This approach was applied to detect l-T₃ in plasma samples without any sample pre-treatment. The average recovery from spiked plasma sample was about 93% with a R.S.D. below 5%.     

Chemiluminescence flow-through sensor for pipemidic acid using solid sodium bismuthate as an oxidant

A novel chemiluminscence (CL) flow-through sensor for pipemidic acid is described. It was based on the sensitizing effect of pipemidic acid on the CL oxidation of sulfite by sodium bismuthate in H₂SO₄ media. The solid-phase sodium bismuthate was mechanicially immobilized on the sponge rubber inside of the CL flow cell as CL oxidant. The calibration graph is linear in the range 0.1-10 μg/ml with a detection limit of 6.2×10⁻⁸ g/ml (3σ). A complete analysis could be performed in 1 min with a relative standard deviation (R.S.D.) of 2.5% for 2 μg/ml pipemidic acid (n=8). This method has been successfully applied to determine pipemidic acid in pharmaceutical preparation.     

Synthesizing a nano-composite of BSA-capped Au nanoclusters/graphitic carbon nitride nanosheets as a new fluorescent probe for dopamine detection

A strong red fluorescent nanocomposite, consisting of graphite-like carbon nitride nanosheets (g-C₃N₄ NSs) and serum albumin-capped Au nanoclusters (AuNCs), was synthesized. Dopamine (DA) can quench the red fluorescence of the nanocomposite, based on the Forster resonance energy transfer (FRET) mechanism. In this quenching process, the energy is transferred from the fluorescent g-C₃N₄ NSs-AuNCs to the oxidized DA quinine molecules (DA is easily oxidated to form DA quinine in air). The red fluorescence emission at 420 nm decreases dramatically and the quenching ratio (F₀ – F)/F₀ is linearly related to the concentration of DA in the range of 0.05–8.0 μmol L⁻¹ with a detection limit of 0.018 μmol L⁻¹ (S/N = 3). Additionally, this sensor has a potential of application to assay the DA in the real samples, such as human serum and human urine.     

Enantiospecific resolution of rabeprazole by liquid chromatography on amylose-derived chiral stationary phase using photo diode array and polarimetric detectors in series

A simple and rapid liquid chromatographic method for enantioselective separation and determination of R-(+) and S-(−) enantiomers of rabeprazole in drugs and pharmaceuticals using photo diode array (PDA) and polarimetric detectors connected in series was developed. Chiralpak AD-H (250 mm × 4.6 mm) 5 μm column packed with amylose tris(3,5-dimethylphenyl carbamate) as a stationary phase and the mobile phase containing n-hexane:ethanol:2-propanol(75:15:10, v/v/v) in an isocratic mode has yielded baseline separation with resolution greater than 3.0 at 40 °C. Effects of ethanol, 2-propanol and temperature on separation were studied for optimum resolution. Lansoprazole sulphone was used as an internal standard (IS) for quantitative determination of individual enantiomers in bulk drugs as well as pharmaceutical formulations. The method was validated in terms of accuracy, precision and linearity according to ICH guidelines. The linearity of the method was studied in the range of 0.5-50 μg/ml and the r² was >0.9997. The inter- and intra-day precision of assay were determined (R.S.D. < 1%) and the recoveries were in the range of 99.63-100.22% with <1% R.S.D. The limits of detection (LOD) and quantification (LOQ) were 0.02 μg/ml and 0.07 μg/ml for both the enantiomers, respectively.     

Headspace liquid-phase microextraction using ionic liquid as extractant for the preconcentration of dichlorodiphenyltrichloroethane and its metabolites at trace levels in water samples

A novel technique, high temperature headspace liquid-phase microextraction (HS-LPME) with room temperature ionic liquid (RTIL), 1-butyl-3-methylimidazolium hexafluorophosphate ([C₄MIM][PF₆]) as extractant, was developed for the analysis of dichlorodiphenyltrichloroethane (p,p′-DDT and o,p′-DDT) and its metabolites including 4,4′-dichlorodiphenyldichloroethylene (p,p′-DDE) and 4,4′-dichlorodiphenyldichloroethane (p,p′-DDD) in water samples by high performance liquid chromatography with ultraviolet detection. The parameters such as salt content, sample pH and temperature, stirring rate, extraction time, microdrop volume, and sample volume, were found to have significant influence on the HS-LPME. The conditions optimized for extraction of target compounds were as follows: 35% NaCl (w/v), neutral pH condition, 70 °C, 800 rpm, 30 min, 10 μL [C₄MIM][PF₆], and 25 mL sample solutions. Under the optimized conditions, the linear range, detection limit (S/N = 3), and precision (R.S.D., n = 6) were 0.3-30 μg L⁻¹, 0.07 μg L⁻¹, and 8.0% for p,p′-DDD, 0.3-30 μg L⁻¹, 0.08 μg L⁻¹, and 7.1% for p,p′-DDT, 0.3-30 μg L⁻¹, 0.08 μg L⁻¹, and 7.2% for o,p′-DDT, and 0.2-30 μg L⁻¹, 0.05 μg L⁻¹, and 6.8% for p,p′-DDE, respectively. Water samples including tap water, well water, snow water, reservoir water, and wastewater were analyzed by the proposed procedure and the recoveries at 5 μg L⁻¹ spiked level were in the range of 86.8-102.6%.     

Liquid chromatographic determination of cis-platin as platinum(II) in pharmaceutical preparation, serum and urine samples of cancer patients

Spectrophotometric and high performance liquid chromatographic (HPLC) methods have been developed for the determination of cis-platin and carboplatin based on the pre-column derivatization of platinum(II) with 2-acetylpyridine-4-phenyl-3-thiosemicarbazone. The complex was extracted in chloroform with molar absorptivity of 2.2 × 10⁴ L mol⁻¹ cm⁻¹ at 380 nm. The complex eluted from a Phenomenex C-18 (150 mm × 4.6 mm i.d.) column with methanol:water:acetonitrile:tetrabutyl ammonium bromide (1 mM) (44:30:25:1, v/v/v/v) with a flow rate of 1 ml/min and UV detection at 260 nm. Ruthenium(IV) and selenium(IV) also separated completely. The linear calibration curve was with 0.5-12.5 μg/ml and detection limit of 10 ng/ml platinum(II).The analysis of cis-platin and carboplatin injections by spectrophotometric and HPLC methods indicated relative standard deviation (R.S.D.) of 0.66-2.1%. The method was used for the determinations of cis-platin in serum and urine of cancer patients after chemotherapy and platinum contents were found 148-444 and 50-90 ng/ml with R.S.D. of 0.3-3.0 and 0.6-2.4% for the serum and urine, respectively. The recovery of platinum(II) from serum was 97% with R.S.D. 2.2%.     

Thermodynamic studies on SrFe12O19(s), SrFe2O4(s), Sr2Fe2O5(s) and Sr3Fe2O6(s)

The citrate-nitrate gel combustion route was used to prepare SrFe₂O₄(s), Sr₂Fe₂O₅(s) and Sr₃Fe₂O₆(s) powders and the compounds were characterized by X-ray diffraction analysis. Different solid-state electrochemical cells were used for the measurement of emf as a function of temperature from 970 to 1151 K. The standard molar Gibbs energies of formation of these ternary oxides were calculated as a function of temperature from the emf data and are represented as (SrFe₂O₄, s, T)/kJ mol⁻¹ (±1.7)=−1494.8+0.3754 (T/K) (970?T/K?1151). (Sr₂Fe₂O₅, s, T)/kJ mol⁻¹ (±3.0)=−2119.3+0.4461 (T/K) (970?T/K?1149). (Sr₃Fe₂O₆, s, T)/kJ mol⁻¹ (±7.3)=−2719.8+0.4974 (T/K) (969?T/K?1150).Standard molar heat capacities of these ternary oxides were determined from 310 to 820 K using a heat flux type differential scanning calorimeter (DSC). Based on second law analysis and using the thermodynamic database FactSage software, thermodynamic functions such as Δ_fH°(298.15 K), S°(298.15 K) S°(T), C_p°(T), H°(T), {H°(T)-H°(298.15 K)}, G°(T), free energy function (fef), Δ_fH°(T) and Δ_fG°(T) for these ternary oxides were also calculated from 298 to 1000 K.     

Fluorescence and terbium-sensitised luminescence determination of garenoxacin in human urine and serum

Fluorescence and terbium-sensitised luminescence properties of new quinolone garenoxacin have been studied. The fluorimetric method allows the determination of 0.060-0.600 μg ml⁻¹ of garenoxacin in aqueous solution containing HCl/KCl buffer (pH 1.5) with λ_exc=282 nm and λ_em=421 nm. Micellar-enhanced fluorescence was also studied, leading to a higher than 400% increase in analytical signal in presence of 12 mM sodium dodecyl sulphate (SDS), allowing the determination of 0.020-0.750 μg ml⁻¹ of garenoxacin. The terbium-sensitised luminescence method allows the determination of 0.100-1.500 μg ml⁻¹ of garenoxacin in 12 mM SDS solution containing 0.08 M acetic acid/sodium acetate buffer (pH 4.1) and 7.5 mM Na₂SO₃ (chemical deoxygenation agent), with λ_exc=281 nm and λ_em=546 nm. Relative standard deviation (R.S.D.) values for the three methods were in the range 1.0-2.0%. The proposed procedures have been applied to the determination of garenoxacin in spiked human urine and serum.     

A novel spectrofluorimetric method for the ultra trace analysis of nitrite and nitrate in aqueous medium and its application to air, water, soil and forensic samples

A highly sensitive and virtually specific method has been developed for the trace and ultra trace 5 ng ml⁻¹-1 μg ml⁻¹ fluorimetric analysis of nitrite. The method is based on the quenching action of nitrite on the native fluorescence of murexide (ammonium purpurate) [λ_ex=349.0 nm, λ_em=444.5 nm] in the acid range of 0.045-0.315 (M) H₂SO₄. The method is very precise and accurate (S.D.=±0.4877 and R.S.D.=0.4878% for the determination of 0.1 μg ml⁻¹ of nitrite in 11 replicates). Relatively large excesses of over 35 cations and anions do not interfere. The proposed technique has been successfully applied for the determination of nitrite and nitrate in ground water, surface water and sea water, nitrite in soil and nitrate in forensic samples. The method has also been extended for the analysis of NO_x in air.     

Synthesis and application of a functionalized resin for flow injection/F AAS copper determination in waters

This paper reports the development of a new strategy for low-level determination of copper in water samples by using a flow-injection system coupled to solid-phase extraction (SPE) using flame atomic absorption spectrometry (F AAS) as detector. In order to preconcentrate copper from samples, a minicolumn packed with a styrene-divinylbenzene resin functionalized with (S)-2-[hydroxy-bis-(4-vinyl-phenyl)-methyl]-pyrrolidine-1-carboxylic acid ethyl ester was used and the synthesis procedure is described. System operation is based on the on-line retention of Cu(II) ions at pH 9.0 ± 0.2 in a such minicolumn with posterior analyte elution with 2 mol l⁻¹ HCl directly to the F AAS nebulizer. The influence of several chemical (sample pH, buffer concentration, HCl eluent concentration and effect of the ionic strength) and flow (sample and eluent flow rates and preconcentration time) variables that could affect the performance of this system were investigated as well as the possible interferents. At optimized conditions, for 2 min of preconcentration time (13.2 ml of sample volume), the system achieved a detection limit of 1.1 μg l⁻¹, a R.S.D. 1% at 20 μg g l⁻¹ and an analytical throughput of 25 h⁻¹, whereas for 4 min of preconcentration time (26.4 ml of sample volume), a detection limit of 0.93 μg l⁻¹, a R.S.D. 5.3% at 5 μg l⁻¹ and a sampling frequency of 13 h⁻¹ were reported.     

Comparison of pyrimethanil-imprinted beads and bulk polymer as stationary phase by non-linear chromatography

A pyrimethanil-imprinted polymer (P1) was prepared by iniferter-mediated photografting a mixture of methacrylic acid and ethylene dimethacrylate onto homemade near-monodispersed chloromethylated polydivinylbenzene beads. The chromatographic behaviour of a column packed with these imprinted beads was compared with another column packed with irregular particles obtained by grinding a bulk pyrimethanil-imprinted polymer (P2). The comparison was made using the kinetic model of non-linear chromatography, studying the elution of the template and of two related substances, cyprodinil and mepanipyrim. Extension of the region of linearity, capacity factors for the template and the related substances, column selectivity, binding site heterogeneity, apparent affinity constant (K) and lumped kinetic association (k_a) and dissociation rate constant (k_d) were studied during a large interval of solute concentration, ranging between 1 and 2000 μg/ml. From the experimental results obtained, in the linearity region of solute concentration column selectivity and binding site heterogeneity remained essentially the same for the two columns, while column capacity (at 20 μg/ml, P1 = 23.1, P2 = 11.5), K (at 20 μg/ml, P1 = 8.3 × 10⁶ M⁻¹, P2 = 2.5 × 10⁶ M⁻¹) and k_a (at 20 μg/ml, P1 = 3.5 μM⁻¹ s⁻¹, P2 = 0.47 μM⁻¹ s⁻¹) significantly increased and k_d (at 20 μg/ml, P1 = 0.42 s⁻¹, P2 = 0.67 s⁻¹) decreased for the column packed with the imprinted beads. These results are consistent with an influence of the polymerisation method on the morphology of the resulting polymer and not on the molecular recognition properties due to the molecular imprinting process.     

Simultaneous determination of sulfamonomethoxine, sulfadimethoxine, and their hydroxy/N(4)-acetyl metabolites with gradient liquid chromatography in chicken plasma, tissues, and eggs

A simultaneous determination of sulfamonomethoxine, sulfadimethoxine, and their hydroxy/N⁴-acetyl metabolites in chicken plasma, muscle, liver, and eggs using gradient high-performance liquid chromatography (HPLC) with a photo-diode array detector is developed. All the compounds are extracted by a handheld ultrasonic homogenizer with ethanol followed by centrifugation. The separation is performed by a reversed-phase C4 column with a gradient elution (ethanol:1% (v/v) acetic acid, v/v; 10:90 → 20:80). Average recoveries from samples spiked at 0.1-1.0 μg g⁻¹ or μg ml⁻¹ for each drug were >90% with relative standard deviations within 4%. The limits of quantitation were <30 ng g⁻¹ or ng ml⁻¹.     

Rapid and simultaneous analysis of dichlorvos, malathion, carbaryl, and 2,4-dichlorophenoxy acetic acid in citrus fruit by flow-injection ion spray ionization tandem mass spectrometry

A simple method for the rapid and simultaneous analysis of dichlorvos (DDVP), malathion, carbaryl, and 2,4-dichlorophenoxy acetic acid (2,4-D) in citrus fruit, which uses flow-injection ion spray ionization tandem mass spectrometry, has been developed for the first time. The method involves the combined use of stable isotopically labeled internal standards (DDVP-d₆, malathion-d₁₀, carbaryl-d₇, and 2,4-D-d₅) and a multiple reaction monitoring technique. The average recoveries for the pesticides at the same concentrations as their tolerance levels (DDVP: 0.1-0.2 μg g⁻¹; malathion: 0.5-4.0 μg g⁻¹; carbaryl: 1.0 μg g⁻¹; 2,4-D: 1.0-2.0 μg g⁻¹) ranged from 90 to 119% with the relative standard deviation (R.S.D.) ranging from 1.0 to 13.1% (n = 5). Analysis time, including sample preparation and determination, was only 15 min. The present method is effective for screening DDVP, malathion, carbaryl, and 2,4-D in citrus fruit.     

Determination of cefuroxime axetil in tablets and biological fluids using liquid chromatography and flow injection analysis

In the present work, the separations of calixarene derivatives have been investigated using both high-performance liquid chromatography (HPLC) and nonaqueous capillary electrophoresis (NACE) techniques. HPLC-1 method with LC-318 (pore size = 300 Å) column and MeCN mobile phase was optimized for the separation of calixarenes. At the flow-rate of 1 ml/min p-nitrocalix[6]arene, calix[4]arene and calix[6]arene could be well baseline and symmetrically separated within 5 min. For the separation of p-tert-butylcalix[n]arenes (n = 4, 6, 8), HPLC-2 and NACE methods have been optimized. The optimal conditions in HPLC-2 method included NH₂ column and MeCN mobile phase, and p-tert-butylcalix[n]arenes (n = 4, 6, 8) were baseline separated within 10 min at 0.8 min/min. The optimal conditions for NACE method employed MeCN-H₂O (8:2, v/v) as the nonaqueous medium and 120 mM Tris/HCl (pH 9.0) as the buffer, and p-tert-butylcalix[n]arenes (n = 4, 6, 8) were successfully baseline resolved within 16 min. With the detection at 280 nm, the calibration lines were linear in the ranges of 1-200 μg/ml for calixarene derivatives by HPLC-1 and HPLC-2 methods, and of 2.5-200 μg/ml for p-tert-butylcalix[n]arenes (n = 4, 6, 8) by NACE method, respectively. The detection limits (S/N = 3) and recoveries ranged from 0.5 to 1.4 μg/ml and from 98.1 to 102.4% by both HPLC-1 and HPLC-2 methods, and from 1.3 to 2.0 μg/ml and from 97.9 to 105.1% by NACE method, respectively. The intra-day reproducibility of the methods was determined with satisfactory results. The proposed HPLC and NACE methods were accurate and reproducible, and could be utilized to separate and determine calixarene derivatives.     

Synthesis, structure and magnetic properties of R-W-O-N (R=Nd and Eu) oxynitrides

Neodymium and europium tungsten oxynitrides have been synthesized by the nitridation of corresponding R₂W₂O₉ precursor oxides, in ammonia flow at 1173 K during 24 h. The obtained polycrystalline neodymium oxynitride phase, with NdWO_3.05N_0.95 composition, crystallizes with the tetragonal symmetry of the scheelite-type structure, space group S.G. I4₁/a (#88). The analogous europium derivative, with formula EuWO_1.58N_1.42, presents the cubic perovskite-type structure, S.G. (# 221). Unit-cell parameters, a=5.255(1) Å, c=11.399(3) Å, and a=3.976(3) Å, have been established from Rietveld refinements of collected X-ray powder diffraction patterns for the Nd and Eu- oxynitrides, respectively.Magnetic susceptibility measurements show that NdWO_3.05N_0.95 behaves as paramagnetic in a wide range of temperature T ∼50-300 K. The downwards deviation from the Curie-Weiss law below 40 K reflects the splitting of the ⁴I_9/2 ground state of Nd³⁺ experienced under the influence of a S₄ crystal field CF potential, as the successful reproduction of the magnetic susceptibility χ⁻¹_m vs. T, using semi-empirical structure-derived CF parameters, indicates. EuWO_1.58N_1.42 is paramagnetic down to 20 K, and the measured effective magnetic moment 8.01 μ_B is indicative of the presence of Eu²⁺ in this oxynitride. The observed sudden jump in the magnetic susceptibility at 20 K and the value of 6 μ_B for the saturation moment is attributed to the onset of ferrimagnetic interactions in which the Eu²⁺ and W⁵⁺ sublattices appear to be involved.     

Simultaneous determination of amiodarone and its metabolite desethylamiodarone by high-performance liquid chromatography with chemiluminescent detection

A novel method was developed for the determination of amiodarone and desethylamiodarone by high-performance liquid chromatography (HPLC) coupled with chemiluminescent (CL) detection. The procedure is based on the post-column photolysis of the analytes into photoproducts which are active in the tris(2,2′-bipyridyl)ruthenium(III) [Ru(bpy)₃³⁺] CL system. Ru(bpy)₃³⁺ was on-line generated by photo-oxidation of the Ru(II) complex in the presence of peroxydisulfate. The separation was carried out on a Mediterranea C₁₈ column with isocratic elution using a mixture of methanol and 0.017 mol L⁻¹ ammonium sulfate buffer of pH 6.8. Under the optimum conditions, analytical curves, based on standard solutions, were linear over the range 0.1-50 μg mL⁻¹ for amiodarone and 0.5-25 μg mL⁻¹ for desethylamiodarone. The detection limits of amiodarone and desethylamiodarone were 0.02 and 0.11 μg mL⁻¹, respectively. Intra- and inter-day precision values of 0.9% relative standard deviation (R.S.D.) (n = 10) and 1.6% R.S.D. (n = 15), respectively, were obtained. The method was applied successfully to the determination of these compounds in serum and pharmaceutical formulations.     

Rapid determination of acetaminophen and p-aminophenol in pharmaceutical formulations using miniaturized capillary electrophoresis with amperometric detection

Capability of fast analysis of a novel miniaturized capillary electrophoresis with carbon disk electrode amperometric detection (mini-CE-AD) system was demonstrated by determining acetaminophen and p-aminophenol in dosage forms. Factors influencing the separation and detection processes were examined and optimized. Under the optimum conditions, the end-capillary 300 μm carbon disc electrode amperometric detector offered favorable signal-to-noise characteristics at a relatively low potential (+600 mV versus Ag/AgCl) for detecting acetaminophen and p-aminophenol. Two analytes can been separated within 150 s in a 8.5 cm length capillary at a separation voltage of 2000 V using a Na₂B₄O₇-KH₂PO₄ running buffer (pH 7.2). Acetaminophen and p-aminophenol could be detected down to the 1.4 × 10⁻⁶-5.9 × 10⁻⁷ mol L⁻¹ level with linearity up to the 1.0 × 10⁻³ mol L⁻¹ level examined. The inter-day repeatability for analytes in peak current (R.S.D. ≤ 2.3%) and migration times (R.S.D. ≤ 1.3%) were excellent. The proposed mini-CE-AD system should find a wide range of analytical applications in pharmaceutical formulations as an alternative to conventional CE and μ-CE.     

Quantification of ziram and zineb residues in fog-water samples

The present paper describes the extractive quantification of zinc-dithiocarbamate fungicides, i.e. ziram (zinc bis-dimethyldithiocarbamate) and zineb (zinc ethylene-1,2-bis-dithiocarbamate) in fog-water samples. The method is based on the releasing of equivalent amount of zinc from the fungicides and its subsequent determination by visible spectrophotometry or by flame-atomic absorption spectrometry (flame-AAS). For spectrophotometry, the sample contained up to 48 μg of ziram and 42 μg of zineb was first equilibrated with chloroform. The recovery results show that only ziram content was extracted into chloroform. Then, the sample was treated with NH₄SCN and surfactants (i.e. CPC and TX-100) solutions, and extracted with toluene to remove interference of inorganic zinc and other metal ions, if present in the sample. The residue was further used for zineb determination. The chloroform extract and residue were then digested separately with nitric acid to release Zn(II), which were then analyzed spectrophotometerically with 4-(2-pyridylazo)-resorcinol in the micellar medium (TX-100) for the determination of ziram and zineb, respectively. The complex shows λ_max at 495 nm. The molar absorptivity in terms of ziram/zineb was determined to be (8.05) × 10⁴ L mole⁻¹ cm⁻¹. The detection limits for ziram and zineb were calculated to be 20 and 21 μg L⁻¹ (with R.S.D. < 1.5%), respectively. Whereas, the optimum concentration ranges were 0.08-1.6 and 0.07-1.4 mg L⁻¹, respectively. Alternatively, the Zn contents present in chloroform extract and in residue were directly analyzed using flame-AAS without undergoing the digestion procedure, and ziram and zineb were determined, respectively. The optimum concentration ranges were 0.9-4.8 and 0.8-4.3 mg L⁻¹, while the detection limits were calculated to be 145 and 144 μg L⁻¹, respectively with R.S.D. < 2.5%. The methods are free from interference of almost all ions [including Zn(II)] and other dithiocarbamate pesticides, which can commonly associate with ziram/zineb in fog-water.     

Determination of hydrogen sulfide and volatile thiols in air samples by mercury probe derivatization coupled with liquid chromatography-atomic fluorescence spectrometry

A new procedure is proposed for the sampling and storage of hydrogen sulphide (H₂S) and volatile thiols (methanethiol or methyl mercaptan, ethanethiol and propanethiol) for their determination by liquid chromatography. The sampling procedure is based on the trapping/pre-concentration of the analytes in alkaline aqueous solution containing an organic mercurial probe p-hydroxymercurybenzoate, HO-Hg-C₆H₄-COO⁻ (PHMB), where they are derivatized to stable PHMB complexes based on mercury-sulfur covalent bonds. PHMB complexes are separated on a C₁₈ reverse phase column, allowing their determination by liquid chromatography coupled with sequential non-selective UV-vis (DAD) and mercury specific (chemical vapor generation atomic fluorescence spectrometry, CVGAFS) on-line detectors. PHMB complexes, S(PHMB)₂CH₃S-PHMB, C₂H₅S-PHMB and C₃H₇S-PHMB, are stable alt least for 12 h at room temperature and for 3 months if stored frozen (−20 °C).The best analytical figures of merits in the optimized conditions were obtained by CVGAFS detection, with detection limits (LODc) of 9.7 μg L⁻¹ for H₂S, 13.7 μg L⁻¹ for CH₃SH, 17.7 μg L⁻¹ for C₂H₅SH and 21.7 μg L⁻¹ for C₃H₇SH in the trapping solution in form of RS-PHMB complexes, the relative standard deviation (R.S.D.) ranging between 1.0 and 1.5%, and a linear dynamic range (LDR) between 10 and 9700 μg L⁻¹. Conventional UV absorbance detectors tuned at 254 nm can be employed as well with comparable R.S.D. and LDR, but with LODc one order of magnitude higher than AFS detector and lower specificity. The sampling procedure followed by LC-DAD-CVGAFS analysis has been validated, as example, for H₂S determination by a certified gas permeation tube as a source of 3.071 ± 0.154 μg min⁻¹ of H₂S, giving a recovery of 99.8 ± 7% and it has been applied to the determination of sulfur compounds in real gas samples (biogas and the air of a plant for fractional distillation of crude oil).     

Determination of bisphenol A, 4-n-nonylphenol, and 4-tert-octylphenol by temperature-controlled ionic liquid dispersive liquid-phase microextraction combined with high performance liquid chromatography-fluorescence detector

Present study described a simple, sensitive, and viable method for the determination of bisphenol A, 4-n-nonylphenol and 4-tert-octylphenol in water samples using temperature-controlled ionic liquid dispersive liquid-phase microextraction coupled to high performance liquid chromatography-fluorescence detector. In this experiment, 1-octyl-3-methylimidazolium hexafluorophosphate ([C₈MIM][PF₆]) was used as the extraction solvent, and bisphenol A, 4-n-nonylphenol and 4-tert-octylphenol were selected as the model analytes. Parameters affecting the extraction efficiency such as the volume of [C₈MIM][PF₆], dissolving temperature, extraction time, sample pH, centrifuging time and salting-out effect have been investigated in detail. Under the optimized conditions, good linear relationship was found in the concentration range of 1.0-100 μg L⁻¹ for BPA, 1.5-150 μg L⁻¹ for 4-NP, and 3-300 μg L⁻¹ for 4-OP, respectively. Limits of detection (LOD, S/N = 3) were in the range of 0.23-0.48 μg L⁻¹. Intra day and inter day precisions (RSDs, n = 6) were in the range of 4.6-5.5% and 8.5-13.3%, respectively. This method has been also successfully applied to analyze the real water samples at two different spiked concentrations and excellent results were obtained.