Surface characterization of the Zn-Ni-Al2O3 nanocomposite coating fabricated under ultrasound condition

Zn-Ni-Al₂O₃ nanocomposite coating, which was fabricated by eletrodeposition technique with the aid of ultrasound, was investigated by scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis and X-ray photoelectron spectroscopy (XPS). The results reveal that 7.2 wt.% nano-alumina particles uniformly dispersed in the matrix of the composite coating. The XPS analyses demonstrate that the outermost layer of Zn-Ni-Al₂O₃ coating was composed of nano-alumina and Zn(OH)₂, while the transition layer between the outermost layer and the Zn-Ni matrix consisted of nano-alumina, metallic Zn, ZnO and metallic Ni. In order to investigate the influences of ultrasonic agitation and the incorporation of nano-alumina on the composition and surface structure of Zn-Ni matrix, the comparison studies of Zn-Ni-Al₂O₃ nanocomposite coating with Zn-Ni coatings fabricated with and without ultrasound were conducted. The results indicate that ultrasonic agitation resulted in a decrease of Ni content in the Zn-Ni matrix and an increase of the thickness of surface oxide layer; while the incorporation of nano-α-Al₂O₃ increased the Ni content in the Zn-Ni matrix.     

Single-calcination synthesis of pyrochlore-free Pb(Ni1/3Nb2/3)O3-PbTiO3 using a coating method

Pyrochlore-free 0.64Pb(Ni_1/3Nb_2/3)O₃-0.36PbTiO₃ (0.64PNN-0.36PT) powder has been successfully synthesized by only one calcination step using a coating method. The formation of pyrochlore phase is prevented by coating NiCO₃·2Ni(OH)₂·2H₂O on Nb₂O₅ particles. NiCO₃·2Ni(OH)₂·2H₂O-coated Nb₂O₅ powder is prepared by heterogeneous precipitation method. The coating structure is confirmed by transmission electron microscope (TEM) with energy dispersive spectroscope (EDS). Single calcination treatment of the coating powder mixed with appropriate amounts of Pb₃O₄ and TiO₂ powders at 900 °C for 2 h produces the pure-perovskite 0.64PNN-0.36PT powder. The elimination of the pyrochlore phase can be explained in terms of the separating of Pb₃O₄ and Nb₂O₅ by the NiCO₃·2Ni(OH)₂·2H₂O coating layer.     

Dielectric properties and temperature stability of BaTiO3 co-doped La2O3 and Tm2O3

The influence of La₂O₃ and Tm₂O₃ co-doping on the dielectric properties and the temperature stability of BaTiO₃ was investigated. BaTiO₃ ceramics were prepared with the compositional formula of (Ba_1−xLa_x)(Ti_1-x/4−yTm_y)O₃. La₂O₃ and Tm₂O₃ co-doping in BaTiO₃ mainly had effects on an increase in the dielectric constant and the temperature stability, respectively. The increase of La₂O₃ concentration and the decrease of Tm₂O₃ concentration in BaTiO₃ resulted in a decrease of lattice parameter and tetragonality because La³⁺ ion substituting for Ba site is smaller than Ba²⁺ ion and Tm³⁺ ion substituting for Ti site is larger than Ti⁴⁺ ion. With the increase of La₂O₃ and the decrease of Tm₂O₃, the dielectric constant of BaTiO₃ was enhanced in spite of the reduction of tetragonality. P-E hysteresis measurements revealed that this phenomenon was based on the improvement of remanent polarization with the increase of La₂O₃ concentration. The introduction of excess Tm₂O₃ in BaTiO₃ suppressed the grain growth and BaTiO₃ ceramics showed higher temperature stability due to the stable tetragonal structure and the small grain size with the increase of Tm₂O₃ concentration.     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

Oxidation of CO on Fe2O3 model surfaces

Using first principles calculations based on a gradient corrected density functional formalism we show that Fe₂O₃ nano-particles with (1 0 0) and (0 0 0 1) surface orientations can oxidize CO to form CO₂ with or without the presence of O₂. However, depending on the surface orientation, the oxidation occurs through differing sequences. On the (1 0 0) surface, in the absence of O₂, two CO molecules are required for one CO oxidation in a concerted reaction while on a oxygen terminated (0 0 0 1) surface, a single CO molecule itself, without the aid of a second CO, can react with the lattice oxygen atoms to form CO₂. In the presence of O₂, the O vacancies created by an initial oxidation through lattice oxygen act as the favored sites for O₂ adsorption which can subsequently oxidize the incoming CO. Detailed reaction paths and the corresponding energetics for the proposed mechanisms are also studied.     

Novel approach to preparation of LiMn2O4 core/LiNixMn2−xO4 shell composite

Combining two methods, coating and doping, to modify spinel LiMn₂O₄, is a novel approach we used to synthesize active material. First we coated the LiMn₂O₄ particles with the nickel oxide particles by means of homogenous precipitation, and then the nickel oxide-coated LiMn₂O₄ was calcined at 750 °C to form a LiNi_xMn_2−xO₄ shell on the surface of spinel LiMn₂O₄ particles. Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), cyclic voltammetry (CV) and charge-discharge test were performed to characterize the spinel LiMn₂O₄ before and after modification. The experimental results indicated that a spinel LiMn₂O₄ core is surrounded by a LiNi_xMn_2−xO₄ shell. The resulting composite showed excellent electrochemical cycling performance with an average fading rate of 0.014% per cycle. This improved cycle stability is greatly attributed to the suppression of Jahn-Teller distortion on the surface of spinel LiMn₂O₄ particles during cycling.     

Preparation and characterization of nickel nano-Al2O3 composite coatings by sediment co-deposition

Ni-Al₂O₃ composite coatings were prepared by using sediment co-deposition (SCD) technique and conventional electroplating (CEP) technique from Watt's type electrolyte without any additives. The microstructure, hardness, and wear resistance of resulting composites were investigated. The results show that the incorporation of nano-Al₂O₃ particles changes the surface morphology of nickel matrix. The preferential orientation is modified from (2 0 0) plane to (1 1 1) plane. The microhardness of Ni-Al₂O₃ composite coatings in the SCD technique are higher than that of the CEP technique and pure Ni coating and increase with the increasing of the nano-Al₂O₃ particles concentration in plating solution. The wear rate of the Ni-Al₂O₃ composite coating fabricated via SCD technique with 10 g/l nano-Al₂O₃ particles in plating bath is approximately one order of magnitude lower than that of pure Ni coating. Wear resistance for SCD obtained composite coatings is superior to that obtained by the CEP technique. The wear mechanism of pure Ni and nickel nano-Al₂O₃ composite coatings are adhesive wear and abrasive wear, respectively.     

Upconversion emission enhancement of TiO2 coated lanthanide-doped Y2O3 nanoparticles

To investigate the upconversion emission,this paper synthesizes Tm3+ and Yb3+ codoped Y2O3 nanoparticles,and then coats them with TiO2 shells for different coating times.The spectral results of TiO2 coated nanoparticles indicate that upconversion emission intensities have respectively been enhanced 3.2,5.4,and 2.2 times for coating times of 30,60 and 90 min at an excitation power density of 3.21×102 W.cm 2,in comparison with the emission intensity of non-coated nanoparticles.Therefore it can be concluded that the intense upconversion emission of Y2O3:Tm3+,Yb3+ nanoparticles can be achieved by coating the particle surfaces with a shell of specific thickness.     

Phase transitions in solid solutions (1 ? x)BaTiO3-xBaMg1/3B2/3O3 (B = Nb, Ta)

The dielectric properties of ceramic samples of (1 − x)BaTiO₃-xBaMg_1/3Nb_2/3O₃ and (1 − x)BaTio₃-xBaMg_1/3Ta_2/3O₃ solid solutions (x = 0–0.25) are investigated in the frequency range from 10 Hz to 100 kHz at temperatures of 77–450 K. It is shown that the (x−T) phase diagrams of these solid solutions at x = 0.05 have a multiphase point at which the lines of all three phase transitions of BaTiO₃ converge. Original Russian Text ? V.G. Zalesskiĭ, V.V. Lemanov, E.P. Smirnova, A.V. Sotnikov, N. V. Zaĭtseva, 2007, published in Fizika Tverdogo Tela, 2007, Vol. 49, No. 1, pp. 108–112.     

Preparation and characterization of the electrodeposited Cr-Al2O3/SiC composite coating

To increase the SiC content in Cr-based coatings, Cr-Al₂O₃/SiC composite coatings were plated in Cr(VI) baths which contained Al₂O₃-coated SiC powders. The Al₂O₃-coated SiC composite particles were synthesized by calcining the precursor prepared by heterogeneous deposition method. The transmission electron microscopy analysis of the particles showed that the nano-SiC particle was packaged by alumina. The zeta potential of the particles collected from the bath was up to +23 mV, a favorable condition for the co-deposition of the particles and chromium. Pulse current was used during the electrodeposition. Scanning Electron Microscopy (SEM) indicated that the coating was compact and combined well with the substrate. Energy dispersive X-ray analysis of Cr-Al₂O₃/SiC coatings demonstrated that the concentration of SiC in the coating reached about 2.5 wt.%. The corrosion behavior of the composite coating was studied by potentiodynamic polarization and electrochemical impedance spectroscopy techniques. The data obtained suggested that the Al₂O₃/SiC particles significantly enhanced the corrosion resistance of the composite coating in 0.05 M HCl solution.     

Electrodeposition and characterization of Ni-Y2O3 composite

Nano-sized Y₂O₃ particles were codeposited with nickel by electrolytic plating from a nickel sulfate bath. The effects of the incorporated Y₂O₃ on the structure, morphology and mechanical properties (including microhardness, friction coefficient and wear resistant) of Ni-Y₂O₃ composite coatings were studied. It is observed that the addition of nano-sized Y₂O₃ particles shows apparent influence on the reduction potential and pH of the electrolyte. The incorporated Y₂O₃ increases from 1.56 wt.% to 4.4 wt.% by increasing the Y₂O₃ concentration in the plating bath from 20 to 80 g/l. XRD results reveal that the incorporated Y₂O₃ particles favour the crystal faces (2 0 0) and (2 2 0). SEM and AFM images demonstrate that the addition of Y₂O₃ particles causes a smooth and compact surface. The present study also shows that the codeposited Y₂O₃ particles in deposits decrease the friction coefficient and simultaneously reduce the wear weight loss. Ni-Y₂O₃ composite coatings reach their best microhardness and tribological properties at Y₂O₃ content 4.4 wt.% under the experiment conditions.     

X-ray photoelectron spectroscopic investigations on cubic BaTiO3, BaTi0.9Fe0.1O3 and Ba0.9Nd0.1TiO3 systems

X-ray photoelectron spectroscopic (XPS) studies were carried out on wet-chemically synthesized cubic BaTiO₃, Ba_0.9Nd_0.1TiO₃ and BaTi_0.9Fe_0.1O_3−δ powders. The compounds were prepared by hydrothermal and gel to crystallite conversion technique; and phases formed readily at 420 K. The phase purity of the powders was confirmed from X-ray diffractometry. Chemical state and chemical environment of the constituent elements in the compositions were examined by XPS. Ba²⁺ was found to exist in two different chemical environments in these titanates. The Ti 2p_3/2 photoelectron peak in BaTi_0.9Fe_0.1O_3−δ was found to be broadened after Fe³⁺ substitution. Any resolvable broadening was not observed distinctly in the Ti 2p peak for Ba_0.9Nd_0.1TiO₃, unsintered BaTiO₃ and BaTiO₃ annealed in hydrogen (8% H₂ + Ar) at 1000 K. The prevalence of mixed-valent titanium and iron in BaTi_0.9Fe_0.1O_3−δ composition was evident from the XPS results and was further supported by the enhanced electrical conductivity at 298-550 K for BaTi_0.9Fe_0.1O_3−δ in comparison to BaTiO₃ and Ba_0.9Nd_0.1TiO₃. Hydroxyl incorporation was facilitated by substituting Nd³⁺ in Ba-sublattice. The presence of hydroxyls was observed from the broadening of the O 1s peak in XPS studies of the compounds.     

Effect of nano-Y2O3 on microstructure of laser cladding cobalt-based alloy coatings

Cobalt-based alloy coatings with and without nano-Y₂O₃ particles produced by a 5 kW CO₂ laser on Ni-based superalloy were introduced. Solidified microstructure, phase compositions and distribution of nano-particles were investigated by using optical microscope, SEM, TEM and XRD. The results showed that metastable phases, such as γ-Co and Cr₂₃C₆ existed in cobalt-based alloy coatings. Another two phases (Y₂O₃ and ?-Co) were found by adding nano-Y₂O₃. Without nano-Y₂O₃, rapid directional solidified microstructure of columnar dendrite appeared. Fine and short dendritic microstructure and columnar to equiaxed transition (CET) occurred by adding nano-Y₂O₃ particles. With the increase in amount of nano-Y₂O₃, fully equiaxed crystallization appeared and the formation mechanism was analyzed. The results also showed that the sub-microstructure of the coatings changed from dislocation to stacking fault by adding nano-Y₂O₃.     

Al2O3 supported Ru catalysts prepared by thermolysis of Ru3(CO)12 for catalytic wet air oxidation

Low loading catalysts Ru/γ-Al₂O₃ and Ru-Ce/γ-Al₂O₃ were prepared by thermolysis of Ru₃(CO)₁₂ on γ-Al₂O_3. The catalysts were characterized by XPS, XRD and SEM. Two new Ru species (Ru_A and Ru_B) were detected during the Ru₃(CO)₁₂ decomposition process due to chemical interaction with the active OH groups on the surface of Al₂O₃ support, and the reduction of them can lead to more dispersed metallic phases. The sample was completely decomposed at 673 K in H₂, and RuO₂ was formed with minor amounts of Ru⁰. When the temperature was increased to 773 K to heat the sample, the ratio of Ru⁰ to RuO₂ increased. However, after the addition of CeO₂, only RuO₂ was detected on surface. The catalysts exhibited high activities in Catalytic Wet Air Oxidation (CWAO) of different organic compounds at high concentration such as isopropyl alcohol, phenol, acetic acids and N,N-dimethylformamide, which is attributed to the better dispersion of Ru particles and the addition of CeO₂ further enhanced number of effectively active sites on the cluster-derived catalyst surface.     

电解等离子体法制备Al2O3陶瓷层及其特性研究

利用电弧喷铝并重熔后进行电解等离子体处理(EPP)的方法在Q235钢基体上制备出呈冶金结 合的Al₂O₃陶瓷层.利用XRD，SEM和EDS等手段对陶瓷层的成分和显 微组织进行了分析， 测定了陶瓷层的耐蚀性能和耐磨性能.实验结果表明，陶瓷层主要由α-Al₂O3，γ-Al₂O₃，θ-Al₂O₃以及一 些非晶相组成，组织致密，耐蚀性能和耐磨性能良好. 关键词： 电解等离子体处理 陶瓷层 复合技术 生长机理     

A new hydrothermal blackening technology for Fe3O4 coatings of carbon steel

This paper proposes a new blackening technology for growing magnetite (Fe₃O₄) coating on surface of carbon steel. Dense black coating composed of Fe₃O₄ ultrafine particles could be successfully prepared by hydrothermal treatment of the carbon steel substrate in the N₂H₄·H₂O-FeSO₄-NaOH solution at 150 °C. Electrochemical analysis, including Tafel and electrochemical impedance spectroscopy, indicated that the anodic dissolution reaction was effectively limited and the corrosion resistance increased by the Fe₃O₄ coating. The key factors and growth mechanism for the hydrothermal formation of the Fe₃O₄ coating are also discussed.     

金属纳米团簇复合薄膜Au/BaTiO3与Fe/BaTiO3的PLD制备及其光吸收特征

用脉冲激光沉积技术制备了掺杂纳米金属颗粒Au或Fe的BaTiO₃复合薄膜.用透射电子显微镜和x射线光电子能谱表征了金属颗粒的形态和化学态.330—800nm范围的吸收谱研究表明，掺Au颗粒的BaTiO₃薄膜在580nm附近有一个明显的共振吸收峰，而掺Fe颗粒的BaTiO₃薄膜没有这样的吸收峰.用Mie散射理论对结果进行了分析. 关键词： 复合薄膜 金属颗粒 脉冲激光沉积 吸收谱     

Electrophoretic deposition of BaTiO3/CoFe2O4 multiferroic composite films

Electrophoretic deposition was utilized for preparation of BaTiO₃/CoFe₂O₄ multiferroic composite thick films on indium-tin oxide substrates. The suspensions for electrophoretic experiments were prepared by dispersing BaTiO₃ and CoFe₂O₄ nanoparticles with different molar ratios into solvents composed of ethanol and acetylacetone. Polyvinyl butyral was added to the suspensions in order to enhance the adhesion and strength of deposit and prevent cracking. The zeta potential values of BaTiO₃/CoFe₂O₄ suspensions were measured to be 26.4-36.9 mV. The experiment results showed that deposited films were obtained only when the applied electric field was larger than a certain critical value. XRD and SEM analysis depicted the presence of constituent phases in composite films. The percolation threshold of composite films was improved through dispersing ferromagnetic phase into ferroelectric phase. Therefore, the ferroelectric properties of composite thick films were maintained when the ferromagnetic properties were enhanced significantly with increasing CFO content.     

Structure, band offsets and photochemistry at epitaxial α-Cr2O3/α-Fe2O3 heterojunctions

We test the hypothesis that electron-hole pair separation following light absorption enhances photochemistry at oxide/oxide heterojunctions which exhibit a type II or staggered band alignment. We have used hole-mediated photodecomposition of trimethyl acetic acid chemisorbed on surfaces of heterojunctions made from epitaxial α-Cr₂O₃ on α-Fe₂O₃(0001) to monitor the effect of UV light of wavelength 385 nm (3.2 eV) in promoting photodissociation. Absorption of photons of energies between the bandgaps of α-Cr₂O₃ (E_g = 4.8 eV) and α-Fe₂O₃ (E_g = 2.1 eV) is expected to be strong only in the α-Fe₂O₃ layer. The staggered band alignment should then promote the segregation of holes (electrons) to the α-Cr₂O₃ (α-Fe₂O₃) layer. Surprisingly, we find that the α-Cr₂O₃ surface alone promotes photodissociation of the molecule at hν = 3.2 eV, and that any effect of the staggered band alignment, if present, is masked. We propose that the inherent photoactivity of the α-Cr₂O₃(0001) surface results from the creation of bound excitons in the surface which destabilize the chemisorption bond in the molecule, resulting in photodecomposition.     

UV-laser-light-controlled photoluminescence of metal oxide nanoparticles in different gas atmospheres: BaTiO3, SrTiO3 and HfO2

The photoluminescence (PL) enhancement has been studied at room temperature using various specimen atmospheres (O₂ gas, CO₂ gas, CO₂–H₂ mixture gas, Ar–H₂ mixture gas and vacuum) under 325 nm laser light irradiation on various metal oxides. Of them, the results obtained for BaTiO₃ nanocrystals, SrTiO₃ ones and HfO₂ powder crystal are given in the present paper. Their PL were considerably increased in intensity by irradiation of 325 nm laser light in CO₂ gas and CO₂–H₂ mixture gas. The cause of the PL intensity enhancements is discussed in the light of the exciton theory, the defect chemistry and the photocatalytic theory. The results may be applied for the utilization of greenhouse gas (CO₂) and the optical sensor for CO₂ gas.