Development of an adapted version of polar organic chemical integrative samplers (POCIS-Nylon)

POCIS (polar organic chemical integrative samplers) are increasingly used for sampling polar compounds. Although very efficient for a wide range of pollutants, the classic configuration of the device has a number of limitations, in particular for the sampling of highly polar analytes and hydrophobic compounds. This study presents a new version of the POCIS passive sampler which uses a highly porous Nylon membrane of 30 μm pore size, enabling the sampling of hydrophobic pollutants and improving the accumulation rate of other pollutants. This newly designed tool and the classic POCIS were both tested during a laboratory experiment to evaluate the accumulation kinetics of a selection of pesticides and pharmaceuticals. The observed results show unexpected accumulation kinetics for the new version of POCIS. To explain the data, the use of an intraparticulate diffusion model was required, which also enabled us to propose another explanation of the burst effect observed with the classic POCIS, primarily related to the potential wetting of the device as the first step in the accumulation of compounds.

Preparation of guanidinium terminus-molecularly imprinted polymers for selective recognition and solid-phase extraction (SPE) of [arginine]-microcystins

About 70 % of microcystin (MC) congeners reported in literature consist of l-arginine amino acid (R) with its guanidinium terminal extending out of the cyclic moiety of these MCs. Molecularly imprinted polymer (MIP) bearing guanidinium terminus cavities was successfully synthesised using l-arginine as a template. Non-imprinted polymer (NIP; without template) was also synthesised for control purposes. The surface area, total pore volume and average pore diameter of MIP and NIP were 267.13 m²/g, 0.63 cm³/g and 88.39 Å; 249.39 m²/g; 0.54 cm³/g and 87.14 Å, respectively. The polymers were investigated for selective recognition and extraction of [arginine]-MCs in water using solid-phase extraction/liquid chromatography-electrospray ionisation–mass spectrometry (SPE/LC-ESI-MS) method. Representative model standard solutions (0.5–10.0 μg/L) of MC-LR and MC-LY were spiked in distilled water, recovered by SPE and quantified by LC-ESI-MS. In this study, Oasis Waters? HLB cartridges served as positive control SPE sorbents. The MIP recognised MC-LR with high recoveries (70.8–91.4 %; r ² ?=?0.9962) comparable to HLB cartridges (71.0–91.85 %; r ² ?=?0.9993), whereas the NIP did not recognise or retain MC-LR. Also, neither MIP nor NIP recognised or retained MC-LY. Extracts of environmental toxic Microcystis aeruginosa were subjected to SPE procedure employing MIP, NIP and HLB cartridges. Microcystin-LR, -YR, -RR, -WR, -(H₄)YR and (D-Asp³, Dha⁷)MC-RR were extracted by MIP and HLB cartridges only as confirmed by LC-ESI-MS. This study demonstrated that the prepared MIP have potential applications for the removal in water and LC-ESI-MS identifications of MCs consisting the guanidinium moiety, i.e.[arginine]-MCs, and in particular targeting commonly encountered toxic congeners, MC-LR, -YR and -RR.

HPLC column-switching technique for sample preparation and fluorescence determination of propranolol in urine using fused-core columns in both dimensions

A new and fast high-performance liquid chromatography (HPLC) column-switching method using fused-core columns in both dimensions for sample preconcentration and determination of propranolol in human urine has been developed. On-line sample pretreatment and propranolol preconcentration were performed on an Ascentis Express RP-C-18 guard column (5?×?4.6 mm), particle size, 2.7 μm, with mobile phase acetonitrile/water (5:95, v/v) at a flow rate of 2.0 mL min^?1 and at a temperature of 50 °C. Valve switch from pretreatment column to analytical column was set at 4.0 min in a back-flush mode. Separation of propranolol from other endogenous urine compounds was achieved on the fused-core column Ascentis Express RP-Amide (100?×?4.6 mm), particle size, 2.7 μm, with mobile phase acetonitrile/water solution of 0.5 % triethylamine, pH adjusted to 4.5 by means of glacial acetic acid (25:75, v/v), at a flow rate of 1.0 mL min^?1 and at a temperature of 50 °C. Fluorescence excitation/emission detection wavelengths were set at 229/338 nm. A volume of 1,500 μL of filtered urine sample solution was injected directly into the column-switching HPLC system. The total analysis time including on-line sample pretreatment was less than 8 min. The experimentally determined limit of detection of the method was found to be 0.015 ng mL^?1.

A novel ionic liquid-modified organic-polymer monolith as the sorbent for in-tube solid-phase microextraction of acidic food additives

A novel ionic liquid-modified organic-polymer monolithic capillary column was prepared and used for in-tube solid-phase microextraction (SPME) of acidic food additives. The primary amino group of 1-aminopropyl-3-methylimidazolium chloride was reacted with the epoxide group of glycidyl methacrylate. The as-prepared new monomer was then copolymerized in situ with acrylamide and N,N’-methylenebisacrylamide in the presence of polyethylene glycol (PEG)-8000 and PEG-10,000 as porogens. The extraction performance of the developed monolithic sorbent was evaluated for benzoic acid, 3-hydroxybenzoic acid, cinnamic acid, 2,4-dichlorophenoxyacetic acid, and 3-(trifluoromethyl)-cinnamic acid. Such a sorbent, bearing hydrophobic and anion-exchange groups, had high extraction efficiency towards the test compounds. The adsorption capacities for the analytes dissolved in water ranged from 0.18 to 1.74 μg cm^?1. Good linear calibration curves (R ²?>?0.99) were obtained, and the limits of detection (S/N?=?3) for the analytes were found to be in the range 1.2–13.5 ng mL^?1. The recoveries of five acidic food additives spiked in Coca-Cola beverage samples ranged from 85.4 % to 98.3 %, with RSD less than 6.9 %. The excellent applicability of the ionic liquid (IL)-modified monolithic column was further tested by the determination of benzoic acid content in Sprite samples, further illustrating its good potential for analyzing food additives in complex samples.

Effect of mobile phase on resolution of the isomers and homologues of tocopherols on a triacontyl stationary phase

Reversed-phase liquid chromatographic (RPLC) separation of isomers and homologues of similar polarity is challenging. Tocopherol isomers and homologues are one such example. α, β, γ, and δ-tocopherols have been successfully separated by RPLC on triacontyl (C₃₀) stationary phase. System suitability was tested by using four mobile phases, and observed chromatographic separations of β and γ-tocopherols were compared. Comparison indicated that methanol–tert-butyl methyl ether (TBME) 95:5 (v/v) at a flow rate of 0.75 mL min^?1 was the best mobile phase. Detection systems were also evaluated on the basis of limit of quantification; it was concluded that fluorescence detection was best. The method was validated by analysis of two homologues and two isomers of tocopherol in sesame, maize, and soybean samples. MS coupled with an ESI interface in negative-ion mode [M ? H]^? was used for identification of individual components. It was concluded that addition of TBME to methanol was required to enhance the separation of β and γ-tocopherols, although methanol alone provided similar results. The applicability of the method to cereal, pulse, and oilseed samples was confirmed. The reproducibility of the procedure was good, with relative standard deviations in the range 1.7–3.9 %. Recovery of tocopherols added to sesame samples ranged from 91 to 99 %.

Determination and pharmacokinetic study of the diacid metabolite of norcantharidin in beagle plasma by use of liquid chromatography–tandem mass spectrometry

Because norcantharidin (NCTD) is unstable and subject to ring opening and hydrolysis, the diacid metabolite of norcantharidin (DM-NCTD) is the stable form of NCTD found in normal saline solution. Conversion of NCTD to DM-NCTD is almost 100 %, making it possible to determine and investigate the pharmacokinetics of DM-NCTD converted from NCTD. In this paper, a sensitive, simple and selective liquid chromatographic–tandem mass spectrometric method was developed and validated for determination of DM-NCTD in beagle plasma. DM-NCTD was detected in multiple-reaction monitoring (MRM) mode by using the dehydrated ion 169.3 as precursor ion and its product ion 123.1 as the detected ion. Ribavirin was used as internal standard and detected in MRM mode by use of precursor ions, resulting in a product ion transition of m/z 267.1?→?135.1. This method was successfully used for a pharmacokinetic study of DM-NCTD in beagles after intravenous administration of DM-NCTD in normal saline solution at doses of 0.39, 0.78, and 1.6 mg kg^?1. DM-NCTD had dose-dependent kinetics across the dosage range investigated, with enhanced T _1/2α and AUC_0-12 and apparently decreasing V _d and CL with increasing dosage. After single-dose administration, T _1/2α ranged from 0.20 to 0.55 h, AUC_0-12 from 1.81 to 43.6 μg mL^?1 h^?1, V _d from 228 to 55.9 mL kg^?1, and CL from 220 to 36.5 mL kg^?1 h^?1 (P?<?0.01). The results indicated nonlinear pharmacokinetic behavior of DM-NCTD in beagles, suggesting that the risk of DM-NCTD in normal saline solution intoxication may be non-proportionally increased at higher doses.

Solvent extraction of europium trifluoromethanesulfonate into nitrobenzene by using three electroneutral receptors

From extraction experiments and $ \gamma $ -activity measurements, the extraction constants corresponding to the general equilibrium Eu³⁺(aq) + 3 A^?(aq) + L(nb) $ \Leftrightarrow $ EuL³⁺(nb) + 3A^?(nb) taking place in the two-phase water–nitrobenzene system ( $ {\text{A}}^{ - } = {\text{CF}}_{ 3} {\text{SO}}_{3}^{ - } $ ; L = electroneutral receptors denoted by 1, 2, and 3 – see Scheme 1; aq = aqueous phase, nb = nitrobenzene phase) were evaluated. Further, the stability constants of the EuL³⁺ complexes in nitrobenzene saturated with water were calculated; they were found to increase in the series of 3 < 2 < 1.

Synergistic extraction of some divalent metal cations into nitrobenzene by using strontium dicarbollylcobaltate and electroneutral macrocyclic lactam receptor

From extraction experiments and $ \gamma $ -activity measurements, the exchange extraction constants corresponding to the general equilibrium M²⁺(aq) + 1·Sr²⁺(nb) $ \Leftrightarrow $ 1·M²⁺(nb) + Sr²⁺(aq) taking place in the two-phase water–nitrobenzene system (M²⁺ = Mg²⁺, Ca²⁺, Ba²⁺, Pb²⁺, Cu²⁺, Zn²⁺, Cd²⁺, $ {\hbox{UO}}_{2}^{2 + } $ , Mn²⁺, Co²⁺, Ni²⁺; 1 = macrocyclic lactam receptor–see Scheme 1; aq = aqueous phase, nb = nitrobenzene phase) were evaluated. Moreover, the stability constants of the 1·M²⁺ complexes in nitrobenzene saturated with water were calculated; they were found to increase in the following cation order: Mg²⁺ < Co²⁺ < Cu²⁺, Mn²⁺, Ni²⁺ < Cd²⁺ < Ca²⁺ < Ba²⁺, Zn²⁺ < Pb²⁺ <  $ {\hbox{UO}}_{2}^{2 + } $ .

Preconcentration of trace cadmium ion using magnetic graphene nanoparticles as an efficient adsorbent

Graphene-based magnetic nanoparticles (G-Fe₃O₄) were prepared and used as an effective adsorbent for the solid-phase extraction of trace quantities of cadmium from water and vegetable samples. The method avoids some of the time-consuming steps associated with traditional solid phase extraction. The excellent sorption property of the G-Fe₃O₄ system is attributed to π - π stacking interaction and hydrophobic interactions between graphene and the Cd-PAN complex. The effects of pH, the amount of G–Fe₃O₄, extraction time, type and volume of eluent, desorption time and interfering ions on the extraction efficiency were optimized. The preconcentration factor is 200. Cd(II) was then quantified by flame atomic absorption spectrometry with a detection limit of 0.32 ng mL^?1. The relative standard deviation (at 50 ng mL^?1; for n?=?10) is 2.45 %. The method has a linear analytical range from 1.1 to 150 ng mL^?1, and the recoveries in case of real samples are in the range between 93.1 % and 102.3 %.

Modelling the size and polydispersity of magnetic hybrid nanoparticles for luminescent sensing of oxygen

We report on a strategy to model both the size (d) and the polydispersity (PdI) of magnetic oxygen-sensitive nanoparticles with a typical size of 200 nm in order to increase the surface area. The strategy is based on experimental design and Response Surface Methodology. Nanoparticles were prepared by miniemulsion solvent evaporation of solutions of poly(styrene-co-maleic anhydride). Features of this strategy include (1) a quick selection of the most important variables that govern d and PdI; (2) a better understanding of the parameters that affect the performance of the polymer; and (3) optimized conditions for the synthesis of nanoparticles of targeted d and PdI. The results were used to produce nanoparticles in sizes that range from 100 to 300 nm and with small polydispersity. The addition of a platinum porphyrin complex that acts as a luminescent probe for oxygen and of magnetite (Fe₃O₄) to the polymeric particles, did not affect d and PdI, thus demonstrating that this strategy simplifies their synthesis. The resulting luminescent and magnetic sensor nanoparticles respond to dissolved oxygen with sensitivity (Stern-Volmer constant) of around 35 bar^?1.

Detection of catecholamines in single specimens of groundwater amphipods

Catecholamines play essential roles in several physiological processes in vertebrates as well as in invertebrates. While several studies have shown the presence of these substances in surface water invertebrates, their occurrence in groundwater fauna is unproven. In the present study, the presence of different catecholamines (i.e., noradrenaline, adrenaline, and dopamine) in individual specimens of groundwater amphipods of the genus Niphargus (mostly Niphargus inopinatus) was investigated via two independent analytical methods: HPLC/EcD and UPLC/TOF-MS. Mean values for catecholamine levels were 533 pg mg^?1 fresh weight for noradrenaline, 314 pg mg^?1 for adrenaline, and 16.4 ng mg^?1 for dopamine. The optimized protocol allowed the detection of CAs in single organisms of less than 1 mg fresh weight. Catecholamine concentration patterns in groundwater invertebrates are briefly discussed here with respect to their evolutionary adaptation to an environmentally stable, energy-poor habitat.

A sensitive immunosorbent bio-barcode assay based on real-time immuno-PCR for detecting 3,4,3',4'-tetrachlorobiphenyl

A functionalized gold-nanoparticle bio-barcode assay, based on real-time immuno-PCR (IPCR), was designed for the determination of 3,4,3',4'-tetrachlorobiphenyl (PCB77). 15 nm gold nanoparticles were synthesized, and modified with thiol-capped DNA and goat anti-rabbit IgG. The nanoparticle probes were used to replace antibody–DNA conjugate in the IPCR, and were fixed on the PCR tube wall via the immune reaction. Real-time PCR was performed to quantify the DNA signal directly. Under optimized conditions, the new method was used to detect PCB77 with a linearity range from 5 pg L^?1 to 10 ng L^?1, and the limit of detection (LOD) was 1.72 pg L^?1. Real samples of Larimichthys polyactis, collected from the East China Sea, were analyzed. Recovery was from 82 % to 112 %, and the coefficient of variation (CV) was acceptable. The results were compared with GC–ECD, revealing that the method would be acceptable for providing rapid, semi-quantitative, and reliable test results for making environmental decisions.

Facile synthesis of a porous network-like silver film for electrocatalytic detection of nitrate

We have developed a method for in-situ construction of a porous network-like silver film on the surface of a glassy carbon electrode (GCE). It is based on a galvanic replacement reaction where a layer of copper nanoparticles is first electrodeposited as a sacrificial template. The silver film formed possesses a porous network-like structure and consists of an assembly of numerous nanoparticles with an average size of 200 nm. The electrode displays excellent electrocatalytic activity, good stability, and fast response (within 2 s) toward the reduction of nitrate at a working potential of ?0.9 V. The catalytic currents linearly increase with the nitrate concentrations in the range of 0.08–6.52 mM, with a detection limit of 3.5 μM (S/N?=?3) and a repeatability of 3.4 % (n?=?5).

Voltammetric sensing of thallium at a carbon paste electrode modified with a crown ether

We describe a new method for differential-pulse anodic stripping voltammetric determination of thallium(I) using a carbon paste electrode modified with dicyclohexyl-18-crown-6. The effect of supporting electrolyte (type and pH), accumulation and reduction potential, and of time and amount of modifier were investigated by differential pulse anodic stripping voltammetry. A method was then worked out for the determination of thallium at low levels. Under optimized conditions, the response to Tl(I) is linear in the range from 3.0 to 250 ng mL^?1. The detection limit is 0.86 ng mL^?1. The sensor displays good repeatability (with a relative standard deviation of ±2.70 % for n?=?7) and was applied to the determination of Tl(I) in water, hair samples, and certified reference materials.

Miniaturised enzymatic conductometric biosensor with Nafion membrane for the direct determination of formaldehyde in water samples

A new conductometric enzyme-based biosensor was developed for the determination of formaldehyde (FA) in aqueous solutions. The biosensor was prepared by cross-linking formaldehyde dehydrogenase from Pseudomonas putida with bovine serum albumin in saturated glutaraldehyde vapours (GA) at the surface of interdigitated gold microelectrodes. Nicotinamide adenine dinucleotide cofactor (NAD⁺) was added in solution at each measurement to maintain enzyme activity. Addition of a Nafion layer over the enzyme modified electrode resulted in a significant increase of biosensor signal due to enhanced accumulation of protons generated by enzymatic reaction at the electrode surface. Different parameters affecting enzyme activity or playing a role in ionic transfer through the Nafion membrane were optimised. In optimal conditions (0.045 mg enzyme, 30 min exposure to GA, 0.3 μL of a 1 % (v/v) Nafion solution deposit, measurement in 5 mM phosphate buffer pH 7 containing 20 μM NAD⁺), the biosensor signal was linear up to 10 mM FA, and the detection limit was 18 μM. Relative standard deviations calculated from five consecutive replicates of FA solutions were lower than 5 % in the 1–10 mM range. The biosensor was successfully applied to the determination of FA in spiked water samples (tap water and Rhone river water), with recoveries in the 95–110 % range.

Electrochemical investigation of the interaction between lysozyme-shelled microbubbles and vitamin C

We report loading of vitamin C (ascorbic acid) on to lysozyme-shelled microbubbles. The interaction between lysozyme-shelled microbubbles and vitamin C was studied by use of cyclic and differential pulse voltammetry, zeta potential measurements, and scanning electron microscopy. The effect of microbubbles on electrochemical measurement of ascorbic acid was evaluated. The linear range for ascorbic acid obtained for differential pulse measurement in the presence of 1 mg mL^?1 microbubbles was 1–50 μmol L^?1 (y?=?0.067x?+?0.130, r ²?=?0.995), with a detection limit of 0.5 μmol L^?1. The experimental conditions, i.e., pH and ionic strength, were optimized to improve the interaction between ascorbic acid and lysozyme-shelled microbubbles. The results were satisfactory when the interaction was performed for 1 h in aqueous solution at pH 6. The amount of vitamin C loaded on the microbubbles (90 % of the analyte added, RSD _inter-expt. = 3 %, n?=?6) and the stability of microbubbles–ascorbic acid complex (until 72 h at 25 °C) were also evaluated by use of differential pulse voltammetry and zeta potential measurements.

Cetyltrimethylammonium-coated magnetic nanoparticles for the extraction of bromate,followed by its spectrophotometric determination

We report on a combination of magnetic solid-phase extraction and spectrophotometric determination of bromate. Cetyltrimethylammonium ion was adsorbed on the surface of phenyl-functionalized silica-coated Fe₃O₄ nanoparticles (Ph-SiO₂@Fe₃O₄), and these materials served as the sorbent. The effects of surfactant and amount of sorbent, the composition of the desorption solution, the extraction time and temperature were optimized. Under optimized conditions, an enrichment factor of 12 was achieved, and the relative standard deviation is 2.9 % (for n?=?5). The calibration plot covers the 1–50 ng mL^?1 range with reasonable linearity (r ²?>?0.998); and the limit of detection is 0.5 ng mL^?1. The method is not interfered by ionic compounds commonly found in environmental water samples. It was successfully applied to the determination of bromate in spiked water samples.

Green biosynthesis of silver nanoparticles and nanomolar detection of p-nitrophenol

Green biosynthesis of nanoparticles and their applications in sensor field is of great interest to the researchers. We report herein a simple green approach for the synthesis of silver nanoparticles (Ag-NPs) using Acacia nilotica Willd twig bark and its application for the detection of 4-nitro phenol (4-NP). The synthesized Ag-NPs were characterized by Transmission electron microscopy, X-ray diffraction and elemental analysis. The size of synthesized Ag-NPs was in the range of 10–50 nm. The Ag-NPs modified electrode shows a high sensitivity and selectivity towards the sensing of 4-NP. The fabricated modified electrode shows a low detection limit of 15 nM on the wider linear response range from 100 nM to 350 μM with the sensitivity of 2.58?±?0.05 μAμM^?1 cm^?2. In addition, the fabricated sensor shows good repeatability and reproducibility.

Reagentless d-sorbitol biosensor based on d-sorbitol dehydrogenase immobilized in a sol–gel carbon nanotubes–poly(methylene green) composite

A reagentless d-sorbitol biosensor based on NAD-dependent d-sorbitol dehydrogenase (DSDH) immobilized in a sol–gel carbon nanotubes–poly(methylene green) composite has been developed. It was prepared by durably immobilizing the NAD⁺ cofactor with DSDH in a sol–gel thin film on the surface of carbon nanotubes functionalized with poly(methylene green). This device enables selective determination of d-sorbitol at 0.2 V with a sensitivity of 8.7?μA?mmol^?1?L?cm^?2 and a detection limit of 0.11 mmol?L^?1. Moreover, this biosensor has excellent operational stability upon continuous use in hydrodynamic conditions.

Hemin-adsorbed carbon felt for sensitive and rapid flow-amperometric detection of dissolved oxygen

Hemin was physically adsorbed onto porous carbon felt (CF), a microelectrode ensemble of micro-carbon fiber (ca. 7 μm in diameter) and possessing a three-dimensional random structure. The hemin-CF exhibited a well-defined redox wave that is due to Fe(III)/Fe(II) redox process in hemin, with a formal potential of ?0.32 V (vs. Ag/AgCl) in deoxygenated buffer solution of pH 7.0. The surface coverage of the electroactive hemin molecules on the surface of the CF was calculated to be 5.0?×?10^?11 mol cm^?2, and the apparent heterogeneous electron transfer rate constant is 3.35 s^?1. The hemin-CF electrode displays excellent electrocatalytic activity for the reduction of dissolved oxygen (DO), and the magnitude of the cathodic current increases with increasing concentrations of DO in the sample solution. The electrode was used as a flow-through detector for sensitive and rapid consecutive determination of DO. Deoxygenated pH 7.0 solutions were analyzed at a flow rate of 8.0 mL min^?1 at an applied potential of ?0.2 V, and highly reproducible cathodic peak current responses to DO were observed in the 0.72 to 13.3 mg L^?1 concentration range. The maximum throughput is 170 samples h^?1. The hemin-CF-based amperometric flow-sensor was applied to determine the concentration of DO in environmental water samples.