Determination of gentamicin sulfate and related compounds by high-performance liquid chromatography with evaporative light scattering detection

A rapid and simple method for the separation and quantitation of gentamicin sulfate by HPLC coupled with evaporative light scattering detection (ELSD) has been developed. Detection of the different components of gentamicin is problematic because of the lack of UV absorbing chromophore. The use of the universal ELSD avoids the need for sample derivatization or use of specific detector such as pulsed amperometry. Separation was performed on a highpurity C18 125 mm x 4 mm i.d., 3 microm, reversed phase column with 48.5 mM trifluoroacetic acid-methanol (97:3, v/v), as mobile phase at a flow rate of 0.7 ml/min. The influence of the gas nature, gas pressure and temperature of the drift tube of the detector on the detection response was investigated. Optimization was performed with the help of a specific experimental design software. This method allows the determination of the composition in components C1, C1a, C2, C2a and C2b of gentamicin sulfate samples. Mass spectrometry was employed to confirm the ELSD chromatographic profile. The method was validated using methodology described by the International Conference of Harmonization in the field of Medicinal Substances. Commercial samples of different sources were analyzed and results were in good agreement with specifications of both European and United States Pharmacopoeia.     

鱼翅中硫酸软骨素的酶解-高效液相色谱法测定

建立了一种测定鱼翅中硫酸软骨素的酶解－高效液相色谱方法；该法利用在一定条件下硫酸软骨素能被硫酸软骨素酶ABC定量酶解成软骨素二糖，通过高效液相色谱法测定软骨素二糖的量来计算硫酸软骨素的含量。     

Ion chromatographic measurement of sulfide, methanethiolate, sulfite and sulfate in aqueous and air samples

Simultaneous measurement of sulfur species was investigated using ion chromatography. Sulfide, methanethiolate, sulfite and sulfate are representative of sulfur species. The aqueous sulfur species were simultaneously measured using a two-detector system: suppressor-type conductivity detector for sulfite and sulfate, and fluorometric or electrochemical detector for the reduced sulfur compounds. The major sulfur-containing gases, hydrogen sulfide, methyl mercaptan and sulfur dioxide are collected into aqueous solution as the species listed above. Collection of sulfur gases using a membrane-based cylindrical diffusion scrubber was investigated. Atmospheric hydrogen sulfide and sulfur dioxide are measured by the diffusion scrubber collection and subsequent measurement by ion chromatography without an enrichment column. In addition to the two gases, methyl mercaptan was also determined using a dual scrubber system.     

Hemoglobin determination with paired emitter detector diode

Two ordinary green light-emitting diodes used as light emitter and detector coupled with simple voltmeter form a complete, cost-effective prototype of a photometric hemoglobinometer. The device has been optimized for cuvette assays of total hemoglobin (Hb) in diluted blood using three different chemical methods recommended for the needs of clinical analysis (namely Drabkin, lauryl sulfate, and dithionite methods). The utility of developed device for real analytics has been validated by the assays of total Hb content in human blood. The results of analysis are fully compatible with those obtained using clinically recommended method and clinical analyzer.     

Analysis of neomycin sulfate and framycetin sulfate by high-performance liquid chromatography using evaporative light scattering detection

A rapid and simple method for the determination of main components and related substances of both neomycin sulfate and framycetin sulfate by HPLC and evaporative light scattering detection (ELSD) is described. The method was also used to determine the neomycin B and the sample sulfate content. Detection and quantitation of aminoglycoside antibiotics are problematic because of the lack of UV absorbing chromophore. The use of a universal detector avoids the need for sample derivatization or use of specific detector based on pulsed amperometry described to be difficult in routine assays. Separation was performed with a Polaris C18 150 mm x 4.6 mm i.d., 3 microm reversed-phase column with a solution of 170mM trifluoroacetic acid (TFA) mobile phase at a flow rate of 0.2 mL/min. The chromatographic parameters were optimized with the help of experimental design software. Mass spectrometry (MS) was employed to confirm the ELSD profile. The final method was validated using methodology described by the International Conference of Harmonization in the field of Active Pharmaceutical Ingredients. Commercial samples of different sources were analyzed and results were in good agreement with specifications of the European Pharmacopoeia.     

Novel integrated paired emitter-detector diode (PEDD) as a miniaturized photometric detector in HPLC

A novel low power, low cost, highly sensitive, miniaturized light emitting diode (LED) based flow detector has been used as optical detector for the detection of sample components in high performance liquid chromatography (HPLC). This colorimetric detector employs two LEDs, one operating in normal mode as a light source and the other is reverse biased to work as a light detector. Instead of measuring the photocurrent directly, a simple timer circuit is used to measure the time taken for the photocurrent generated by the emitter LED (lambda(max) 500 nm) to discharge the detector LED (lambda(max) 621 nm) from 5 V (logic 1) to 1.7 V (logic 0) to give digital output directly without using an A/D converter. Employing a post-column reagent method, a Nucleosil 100-7 column (functionalized with iminodiacetic acid (IDA) groups) was used to separate a mixture of transition metal complexes, manganese(II) and cobalt(II) in 4-(2-pyridylazo)-resorcinol (PAR). All optical measurements were taken by using both the in-built HPLC variable wavelength detector and the proposed paired-emitter-detector-diode (PEDD) optical detector configured in-line for data comparison. The concentration range investigated using the PEDD was found to give a linear response to the Mn(II) and Co(II) PAR complexes. The effects of flow rate and emitter LED light source intensity were investigated. Under optimised conditions the PEDD detector offered a linear range of 0.9-100 microM and LOD of 0.09 microM for Mn-PAR complex. A linear range of 0.2-100 microM and LOD of 0.09 microM for Co-PAR complex was achieved.     

Stabilization of sulfide and sulfite and ion-pair chromatography of mixtures of sulfide, sulfite, sulfate and thiosulfate

Ion chromatography of sulfide, sulfite, sulfate and thiosulfate in a mixture is often difficult because of instability of sulfide and sulfite, poor separation of sulfide from common anions such as bromide or nitrate and similar elution-times for sulfite and sulfate. An ion-pair chromatographic method for the determination of these sulfur anions has been established by stoichiometric conversion of sulfide and sulfite into stable thiocyanate and sulfate, respectively, prior to the chromatographic run. Sulfate, thiosulfate and thiocyanate were resolved on an octadecylsilica column with an acetonitrile-water mobile phase containing tetrapropylammonium salt (TPA) as an ion-paring reagent, and thiosulfate and thiocyanate in the effluent could be measured with a photometric detector (220 nm) and sulfate with a suppressed conductivity detector. When an acetonitrile-water (6:94, v/v) mobile phase (pH 5.0) containing 15 mM TPA and small amounts of acetic acid was used at a flow-rate of 0.6 ml min(-1), the three anions could be eluted within 32 min. Calibration plots of peak height versus concentration for sulfide (detected as thiocyanate) and thiosulfate gave straight lines up to 35 and 60 microM, respectively. The calibration plot for sulfide coincided with that obtained by using thiocyanate. A calibration plot for sulfite, measured as sulfate, was also linear up to 135 microM and was in accord with that of sulfate. Each calibration plot gave a correlation coefficient greater than 0.999. For six replicates obtained for a mixture of 30.0 microM sulfide, 50.0 microM sulfite, 50.0 microM sulfate and 20.0 microM thiosulfate, the proposed method gave a mean value of 30.1 microM with a standard deviation (SD) of 0.77 microM and a relative standard deviation (RSD) of 2.6% for sulfide, 101 microM (SD = 3.5 microM, RSD = 3.5%) for the total of sulfite and sulfate and 20.1 microM (SD = 0.44 microM, RSD = 2.2%) for thiosulfate. Recoveries for sulfide, sulfite plus sulfate, and thiosulfate in hot-spring water samples using the proposed method were found to be quantitative.     

Investigation of unknown related substances in commercial neomycin samples with liquid chromatography/ion trap tandem mass spectrometry

The characterization of unknown impurities present in neomycin sulfate by liquid chromatography (LC) coupled with ion trap mass spectrometry (ITMS) is described. The volatile LC method was developed using an evaporative light scattering detector due to its lower investment and operating costs, easier operation and less maintenance than mass spectrometry. The method shows separation of neomycin B from seven potential related substances reported in the European Pharmacopoeia and several other unknown impurities. The unknown impurities were further investigated by coupling the developed LC method with ITMS. Their structures were deduced based on the fragmentation patterns obtained from reference substances. Four unknowns were identified as isomers of paromamine, LP-A, neamine and LP-B.     

Light-scattering detection with a fluorimetric detector in high-performance liquid chromatography

Non-fluorescence compounds were detected by a fluorescence detector based on scattering light. The fluorescence detector was used without any modification, and the scattering light was observed at the wavelength twice as long as the excitation wavelength. Actually the wavelength of the observed scattering light was the same as that of the excitation light. The maximum signal was achieved at around 280 nm. The signal was increased with increasing molecular weight or size of analytes. Colloidal silica with nanometer sizes, ethylene glycol oligomers, saccharides and cyclodextrins could be visualized by the present detection method. The detection limit at S/N=3 for colloidal silica with 78 nm was 39 pg for 20-microL injection.     

Development of micro-flow devices by direct-milling on poly(methyl methacrylate) substrates with integrated optical detection

The development of micro-flow devices by direct-milling on poly(methyl methacrylate) (PMMA) substrates and incorporating the optic detector into the same structure is presented, evaluated and applied to the determination of chlorhexidine. Hydrodynamic characteristics of the developed devices were compared against those obtained from flow systems based on classic Teflon reactors. The optical detector integrated in the PMMA substrate is composed of a light emitting diode (λ?=?627 nm) and light dependence resistance as light source and light detector, respectively. The performance of the optical detector was evaluated and optimized. The applicability of the fluidic device was assessed in the determination of chlorhexidine through its colorimetric reaction with bromocresol green. Micro-pumps were used as propulsion units. Results obtained in real sample analysis were in good agreement with those obtained by the reference procedure.     

Separation of chondroitin sulfate and hyaluronic acid fragments by centrifugal precipitation chromatography

Centrifugal precipitation chromatography (CPC) was applied for the first time to the separation of fragments of chondroitin sulfate (ChS) and hyaluronic acid (HA). The separation was performed using a gradient elution system between ethanol and water since solubility of these biopolymers highly depends on the concentration of ethanol in aqueous solution. ChS and HA were each eluted into several peaks through a flow-through UV detector at 275 nm, despite they have almost no absorbance at this wavelength in an aqueous solution. The separation was also confirmed by redissolving the dried fraction in water and measuring the absorbance at 210 nm. These results suggest that the CPC system can detect small precipitates of these biopolymers by light scattering at 275 nm. The separated fragments of biopolymers are not easily characterized because no suitable analytical method is available for identification of these compounds. However, the overall results demonstrate that CPC may be a useful separation of biopolymers such as glycosaminoglycans which quantitatively produce precipitates in an organic solvent mixture.     

Determination of phosphate using a highly sensitive paired emitter-detector diode photometric flow detector

The use of a novel inexpensive photometric device, a paired emitter-detector diode (PEDD) has been applied to the colorimetric determination of phosphate using the malachite green spectrophotometric method. The novel miniaturized flow detector applied within this manifold is a highly sensitive, low cost, miniaturized light emitting diode (LED) based detector. The optical flow cell was constructed from two LEDs, whereby one is the light source and the second is the light detector, with the LED light source forward biased and the LED detector reversed biased. The photocurrent generated by the LED light source discharges the junction capacitance of the detector diode from 5 V (logic 1) to 1.7 V (logic 0) and the time taken for this process to occur is measured using a simple timer circuit.The malachite green (MG) method employed for phosphate determination is based on the formation of a green molybdophosphoric acid complex, the intensity of which is directly related to phosphate concentration. Optimum analytical parameters such as reaction kinetics, reagent to sample concentration ratio and emitter wavelength intensity were investigated for the spectrophotometric method. Linear calibration plots that obeyed the Beer-Lambert law were obtained for phosphate in the range of 0.02-2 μM. The dynamic range, sensitivity and limits of detection are reported.     

A four-wavelength channel absorbance detector with a light emitting diode-fiber optics assembly for simplifying the flow-injection analysis system.

A four-channel absorbance detector was developed for simplifying the flow-injection analysis (FIA). This detector used four light-emitting-diodes (LEDs) as light sources; their wavelengths were 470, 495, 590 and 635 nm, respectively. Their amplitudes were modulated electronically with different frequencies. The light emissions from them were merged by plastic-core fiber optics, and were detected by a photo-diode (PD). The mixed signal was then sent to and discriminated by a four-channel lock-in amplifier corresponding to each modulation frequency. Neither a monochromator nor an optical filter was used. This detector was conveniently applied to the determination of iron in river water by FIA using 1,10-phenanthroline. Though a noisy peristaltic pump was used to propel the solutions, practical precision and accuracy were obtained by means of on-line dual-wavelength measurements and off-line moving average calculations.     

High-sensitivity, disposable lab-on-a-chip with thin-film organic electronics for fluorescence detection

We report a high-sensitivity, disposable lab-on-a-chip with a thin-film organic light-emitting diode (OLED) excitation source and an organic photodiode (OPD) detector for on-chip fluorescence analysis. A NPB/Alq3 thin-film green OLED with an active area of 0.1 cm(2) was used as the excitation source, while a CuPC/C(60) thin-film OPD with 0.6 cm(2) active area was used as a photodetector. A novel cost-effective, cross-polarization scheme was used to filter out excitation light from a fluorescent dye emission spectrum. The excitation light from the OLED was linearly polarized and used to illuminate a microfluidic device containing a 1 microL volume of dye dissolved in ethanol. The detector was shielded by a second polarizer, oriented orthogonally to the excitation light, thus reducing the photocurrent due to excitation light leakage on the detector by approximately 25 dB. The fluorescence emission light, which is randomly polarized, is only attenuated by approximately 3 dB. Fluorescence signals from Rhodamine 6G (peak emission wavelength of 570 nm) and fluorescein (peak emission wavelength of 494 nm) dyes were measured in a dilution series in the microfluidic device with emission signals detected by the OPD. A limit-of-detection of 100 nM was demonstrated for Rhodamine 6G, and 10 microM for fluorescein. This suggests that an integrated microfluidic device, with an organic photodiode and LED excitation source and integrated polarizers, can be fabricated to realize a compact and economical lab-on-a-chip for point-of-care fluorescence assays.     

Enzymatic Conversion of Cypridina Luciferyl Sulfate to Cypridina Luciferin with Coenzyme A as a Sulfate Acceptor in Cypridina (Vargula) hilgendorfii

In the luminous ostracod Cypridina (presently Vargula) hilgendorfii, Cypridina luciferyl sulfate (3‐enol sulfate of Cypridina luciferin) is converted to Cypridina luciferin by a sulfotransferase with 3′‐phosphoadenosine‐5′‐phosphate (PAP) as a sulfate acceptor. The resultant Cypridina luciferin is used for the luciferase–luciferin reaction of Cypridina to emit blue light. The luminescence stimulation with major organic cofactors was examined using the crude extracts of Cypridina specimens, and we found that the addition of coenzyme A (CoA) to the crude extracts significantly stimulated luminescence intensity. Further, the light‐emitting source in the crude extracts stimulated with CoA was identified as Cypridina luciferyl sulfate, and we demonstrated that CoA could act as a sulfate acceptor from Cypridina luciferyl sulfate. In addition, the sulfate group of Cypridina luciferyl sulfate was also transferred to adenosine 5′‐monophosphate (5′‐AMP) and adenosine 3′‐monophosphate (3′‐AMP) by a sulfotransferase. The sulfated products corresponding to CoA, 5′‐AMP and 3′‐AMP were identified using mass spectrometry. This is the first report that CoA can act as a sulfate acceptor in a sulfotransferase reaction.     

Evaluation of a condensation nucleation light scattering detector for the analysis of synthetic polymer by supercritical fluid chromatography

A condensation nucleation light scattering detector (CNLSD) was adapted for use as a detector for supercritical fluid chromatography. The performance of the CNLSD was evaluated and compared to evaporative light-scattering detector (ELSD) using a well-defined equimass mixture of uniform poly(ethylene glycol) oligomers and a certified reference material of poly(ethylene glycol) 1000. The CNLSD was able to detect a 10 times less concentrated solution of uniform oligomers compared to the ELSD. The quantitativeness of CNLSD was high enough to obtain the molecular mass distribution of poly(ethylene glycol) 1000 without any calibrations; on the other hand, the original data measured by ELSD was about 4% smaller than the certified value of poly(ethylene glycol) 1000. The CNLSD was suitable for supercritical fluid chromatography as a mass concentration detector.     

高效液相色谱法测定硫酸沙丁胺醇

利用高效液相色谱仪-电子捕获检测器(HPLC-ECD)测定了市售片剂硫酸沙丁胺醇的含量.结果表明,利用HPLC-ECD技术测定硫酸沙丁胺醇的线性范围为0.944~33.8mg·L-1(r=0.999 6);回收率为99.0%~107.8%(RSD≤4.6%).该法可用于测定片剂的硫酸沙丁胺含量.     

离子色谱法同时测定那屈肝素钙中氯离子和硫酸根离子的含量

建立了一种抑制电导检测器离子色谱法同时测定那屈肝素钙中氯离子和硫酸根离子含量的方法.采用强阴离子交换柱,3 mmol/L碳酸钠溶液为流动相,流速2.0 mL/min,柱温30℃,进样量25μL,检测器为配有化学抑制器的电导检测器.结果表明,氯离子和硫酸根离子在1～20μg/m L浓度范围内线性关系良好,氯离子线性方程为...     

LED–LED portable oxygen gas sensor

A portable instrument for oxygen determination, based on the quenching of phosphorescent octaethylporphyrin by gaseous O₂, has been developed using the fluorimetric paired emitter–detector diode technique (FPEDD). The instrument configuration consists of two light-emitting diodes (LEDs) facing each other, with an interchangeable support containing a phosphorescent membrane in between, in which one of the LEDs is used as the light source (emitter LED) and the other, working in reverse bias mode, as the light detector. The feasibility of using a LED as a luminescence detector is studied. Its small size enables integration of the instrument into a portable measurement system. A systematic study of the system capabilities as a portable instrument was performed to optimize range, sensitivity, short term and long term stability, dynamic behaviour, effect of temperature and humidity, and temporal drift.     

Absorbance detector based on a deep UV light emitting diode for narrow‐column HPLC

A detector for miniaturized HPLC based on deep UV emitting diodes and UV photodiodes was constructed. The measurement is accomplished by the transverse passage of the radiation from the light‐emitting diode (LED) through fused‐silica tubing with an internal diameter of 250 μm. The optical cell allows flexible alignment of the LED, tubing, and photodiode for optimization of the light throughput and has an aperture to block stray light. A beam splitter was employed to direct part of the emitted light to a reference photodiode and the Lambert–Beer law was emulated with a log‐ratio amplifier circuitry. The detector was tested with two LEDs with emission bands at 280 and 255 nm and showed noise levels as low as 0.25 and 0.22 mAU, respectively. The photometric device was employed successfully in separations using a column of 1 mm inner diameter in isocratic as well as gradient elution. Good linearities over three orders of magnitude in concentration were achieved, and the precision of the measurements was better than 1% in all cases. Detection down to the low micromolar range was possible.