Evaluation of particle size distributions of precipitates in a 9% chromium steel using energy filtered transmission electron microscopy

Energy filtered transmission electron microscopy (EFTEM) has been used to evaluate particle size distributions of different phases in the creep resistant 9% chromium steel P92, aged at 600 or 650°C for up to 26,000 h. Precipitates of type VN, M₂₃C₆ and Laves phase were visualised by forming so-called jump ratio images of the elements vanadium, chromium and tungsten. Digital image analysis was used to measure the size of the precipitates at different ageing times. As a complement to EFTEM, atom probe field ion microscopy (APFIM) has been used to monitor the composition of the ferritic matrix. This indirectly gives information about precipitated volume fraction of different phases. In the case of VN precipitates the volume fraction was also determined from EFTEM images and the result was in good agreement with the data obtained with APFIM. The high-temperature stability of the secondary phases present in steel P92 and their relation to creep properties are discussed. To further study the applicability of EFTEM, steel P122 (with a composition similar to steel P92, but with an addition of Cu) was investigated and a Cu-rich phase was found.     

Study of changes in composition and EELS ionization edges upon Ni4Ti3 precipitation in a NiTi alloy

Concentration gradients surrounding Ni4Ti3 precipitates grown by appropriate annealing in a Ni51Ti49 B2 austenite matrix are investigated by electron energy loss spectroscopy (EELS) and energy filtered transmission electron microscopy (EFTEM). Concentration gradients of approximately 1.0-2.0 at.% in Ni within the surrounding B2 matrix can be detected by both EELS and EFTEM, revealing a Ni depleted zone in the matrix. Besides the concentration gradients, the EELS integrated cross-section of the Ni L(2,3) edges for the Ni-depleted region increased slightly, when compared with a matrix region away from the precipitate and not depleted in Ni.     

EELS study of niobium carbo-nitride nano-precipitates in ferrite

Micro-alloying steels allow higher strength to be achieved, with lower carbon contents, without a loss in toughness, weldability or formability through the generation of a fine ferrite grain size with additional strengthening being provided by the fine scale precipitation of complex carbo-nitride particles. Niobium is reported to be the most efficient micro-alloying element to achieve refinement of the final grain structure. A detailed microscopic investigation is one of the keys for understanding the first stages of the precipitation sequence, thus transmission electron microscopy (TEM) is required. Model Fe-(Nb,C) and Fe-(Nb,C,N) ferritic alloys have been studied after annealing under isothermal conditions. However the nanometre scale dimensions of the particles makes their detection, structural and chemical characterization delicate. Various imaging techniques have then been employed. Conventional TEM (CTEM) and high resolution TEM (HRTEM) were used to characterise the morphology, nature and repartition of precipitates. Volume fractions and a statistical approach to particle size distributions of precipitates have been investigated by energy filtered TEM (EFTEM) and high angle annular dark field (HAADF) imaging. Great attention was paid to the chemical analysis of precipitates; their composition has been quantified by electron energy loss spectroscopy (EELS), on the basis of calibrated 'jump-ratios' of C-K and N-K edges over the Nb-M edge, using standards of well-defined compositions. It is shown that a significant addition of nitrogen in the alloy leads to a complex precipitation sequence, with the co-existence of two populations of particles: pure nitrides and homogeneous carbo-nitrides respectively.     

Size and density control of silicon oxide nanowires by rapid thermal annealing and their growth mechanism

In this work, we demonstrate a fast approach to grow SiO₂ nanowires by rapid thermal annealing (RTA). The material characteristics of SiO₂ nanowires are investigated by field emission scanning electron microscopy, high-resolution transmission electron microscopy (HRTEM), high-angle annular dark-field (HAADF) imaging, electron energy loss spectroscopy (EELS), and energy-filtered TEM (EFTEM). The HAADF images show that the wire tip is predominantly composed of Pt with brighter contrast, while the elemental mappings in EFTEM and EELS spectra reveal that the wire consists of Si and O elements. The SiO₂ nanowires are amorphous with featureless contrast in HRTEM images after RTA at 900°C. Furthermore, the nanowire length and diameter are found to be dependent on the initial Pt film thickness. It is suggested that a high SiO₂ growth rate of >1 μm/min can be achieved by RTA, showing a promising way to enable large-area fabrication of nanowires.     

Inelastic electron scattering observation using energy filtered transmission electron microscopy for silicon -- germanium nanostructures imaging

This paper presents a new technique using energy filtered TEM (EFTEM) for inelastic electron scattering contrast imaging of Germanium distribution in Si-SiGe nanostructures. Comparing electron energy loss spectra (EELS) obtained in both SiGe and Si single crystals, we found a spectrum area strongly sensitive to the presence of Ge in the range [50-100 eV]. In this energy loss window, EELS spectrum shows a smooth steeply shaped background strongly depending on Ge concentration. Germanium mapping inside SiGe can thus be performed through imaging of the EELS background slope variation, obtained by processing the ratio of two energy filtered TEM images, respectively, acquired at 90 and 60 eV. This technique gives contrasted images strongly similar to those obtained using STEM Z-contrast, but presenting some advantages: elastic interaction (diffraction) is eliminated, and contrast is insensitive to polycrystalline grains orientation or specimen thickness. Moreover, since the extracted signal is a spectral signature (inelastic energy loss) we demonstrate that it can be used for observation and quantification of Ge concentration depth profile of SiGe buried layers.     

Energy-filtered TEM imaging and EELS study of ODS particles and argon-filled cavities in ferritic-martensitic steels

Oxide-dispersion-strengthened (ODS) ferritic-martensitic steels with yttrium oxide (Y(2)O(3)) have been produced by mechanical alloying and hot isostatic pressing for use as advanced material in fusion power reactors. Argon gas, usually widely used as inert gas during mechanical alloying, was surprisingly detected in the nanodispersion-strengthened materials. Energy-filtered transmission electron microscopy (EFTEM) and electron energy loss spectroscopy (EELS) led to the following results: (i) chemical composition of ODS particles, (ii) voids with typical diameters of 1-6 nm are formed in the matrix, (iii) these voids are filled with Ar gas, and (iv) the high-density nanosized ODS particles serve as trapping centers for the Ar bubbles. The Ar L(3,2) energy loss edge at 245 eV as well as the absorption features of the ODS particle elements were identified in the EELS spectrum. The energy resolution in the EEL spectrum of about 1.0 eV allows to identify the electronic structure of the ODS particles.     

A combined SNMS and EFTEM/EELS study on focused ion beam prepared vanadium nitride thin films

We investigated the diffusion profiles and core-loss fine-structures (ELNES) of thin vanadium nitride films by electron energy-loss spectroscopy (EELS) and energy filtering transmission electron microscopy (EFTEM). The nitride layers have been produced by rapid thermal processing in a NH₃ or N₂ atmosphere and have then been cross-sectioned with a focused ion beam instrument (FIB) under mild milling conditions to maintain crystallography. For the high-resolution electron energy-loss spectroscopy studies (HREELS), a recently developed TEM gun monochromator, implemented into a 200 kV field emission gun column was used in combination with a new post-column spectrometer. It was found that, dependent on substrate and atmosphere, layers with different vanadium and nitrogen content were formed, showing distinct differences in their ELNES. With an energy resolution at the 0.2 eV level and a TEM beam spot size of approximately 2 nm these layers could be unambiguously identified when compared to theoretical ELNES simulations from the literature.     

Measurement of γ′ precipitates in a nickel-based superalloy using energy-filtered transmission electron microscopy coupled with automated segmenting techniques

Precipitates of the ordered L1₂ γ′ phase (dispersed in the face-centered cubic or FCC γ matrix) were imaged in Rene 88 DT, a commercial multicomponent Ni-based superalloy, using energy-filtered transmission electron microscopy (EFTEM). Imaging was performed using the Cr, Co, Ni, Ti and Al elemental L-absorption edges in the energy loss spectrum. Manual and automated segmentation procedures were utilized for identification of precipitate boundaries and measurement of precipitate sizes. The automated region growing technique for precipitate identification in images was determined to measure accurately precipitate diameters. In addition, the region growing technique provided a repeatable method for optimizing segmentation techniques for varying EFTEM conditions.     

Nano-scale copper oxidation on leadframe surface

Copper oxidation studies were carried out by means of field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS) and electron energy loss spectroscopy (EELS) techniques. The growth of copper oxide occurs as a copper surface comes in an oxygen containing environment. The reaction sequence leading to oxidation of the copper surface is generally accepted to be oxygen chemisorption, nucleation and growth of the surface oxide and bulk oxide growth. HRTEM examination of the cross section of the oxidized copper sample revealed the interface region in between the copper and copper oxide. At high oxidation temperature, formation of micro-voids and separations were observed along this interface region. Poor adhesion at this interface region due to micro-voids and separation were found to be the root cause of delamination issue. EELS analysis determined that for regions with intact interface the oxidation system is Cu/CuO/Cu₂O/CuO, however, in regions containing micro-voids or separation it is found to be Cu/Cu₂O/CuO.     

Phase transitions in Co nanoclusters grown by pulsed laser deposition

The crystalline structure of Co clusters embedded in an amorphous Al₂O₃ matrix was studied by transmission electron microscopy (TEM) and electron diffraction (TED). In the first stage of the growth a metastable structure (body-centred-cubic) is observed. A face-centred-cubic phase (fcc) is found when the size of the clusters increases ( diameter > 4 nm). The hexagonal-close-packed phase arises in the fcc phase by a succession of stacking faults at the largest sizes. The mechanisms of phase transformation have been determined by using high resolution electron microscopy (HREM). The chemical nature of the clusters, in particular the existence of Co-O bonds, was investigated by using electron energy loss spectroscopy (EELS). Received 03 July 2000 and Received in final form 22 December 2000     

Elemental electron energy loss mapping of a precipitate in a multi-component aluminium alloy

The elemental distribution of a precipitate cross section, situated in a lean Al-Mg-Si-Cu-Ag-Ge alloy, has been investigated in detail by electron energy loss spectroscopy (EELS) and aberration corrected high angle annular dark field scanning transmission electron microscopy (HAADF-STEM). A correlative analysis of the EELS data is connected to the results and discussed in detail. The energy loss maps for all relevant elements were recorded simultaneously. The good spatial resolution allows elemental distribution to be evaluated, such as by correlation functions, in addition to being compared with the HAADF image.The fcc-Al lattice and the hexagonal Si-network within the precipitates were resolved by EELS. The combination of EELS and HAADF-STEM demonstrated that some atomic columns consist of mixed elements, a result that would be very uncertain based on one of the techniques alone. EELS elemental mapping combined with a correlative analysis have great potential for identification and quantification of small amounts of elements at the atomic scale.     

HRTEM and TEM studies of amorphous structures in ZrNiTiCu base alloys obtained by rapid solidification or ball milling

Amorphous structure of Ti(25)Zr(17)Ni(29)Cu(29) composition was studied. Alloys were prepared either by rapid solidification using melt spinning or by high-energy ball milling. The composition of multi-component eutectic in slowly cooled samples of ZrNiTiCu alloy was determined using EDS measurements in scanning microscope of slowly cooled cast samples. The alloys of eutectic composition were melt-spun or ball-milled. Transmission electron microscopy (TEM) studies of melt-spun ribbons from alloys near eutectic composition did not show presence of nanocrystals within the amorphous structure. TEM studies of ball-milled powders showed presence of nanocrystallites of size 2-5 nm. The electron diffraction pattern showed intense diffused ring due to the presence of the amorphous phase and a weak spot due to crystalline phases which were difficult to identify. The high temperature high-pressure compaction in vacuum of amorphous ball-milled powders resulted in a similar structure like in the powders showing nanocrystals embedded in the amorphous matrix. The crystallites were imaged using HREM. Interplanar distances were measured in pictures obtained by inverse fast Fourier transform (IFFT) of atomic planes to obtain better contrast. Analysis of the IFFT from high-resolution micrographs allowed to identify Cu(10)Zr(7) phase. Point analysis and elemental mapping performed using nondispersive X-ray energy spectroscopy showed uniform elements distribution indicating that chemical segregation to nanocrystals is within measurement error.     

Transmission electron microscopy and X-ray diffraction study of microstructural evolution in magnetoresistive Cu–Fe–Ni ribbons

The evolution of the microstructure of a granular Cu₈₀Fe₁₀Ni₁₀ (at%) melt-spun ribbon is studied by transmission electron microscopy (TEM), energy-filtered transmission electron microscopy (EFTEM) and X-ray diffraction. This system is interesting as large giant magnetoresistance (GMR) values have been measured for this composition. We have shown the presence of two face-centred cubic phases, an (Fe,Ni)-rich phase and a Cu-rich phase. The lattice parameters of these two phases are close and no diffraction or elastic contrast is involved in displaying the two phases in TEM bright-field mode. With EFTEM imaging, we have shown the presence of a fine-scale (Fe,Ni)-rich precipitation inside the Cu-rich fcc matrix. The precipitates are 2–4 nm in the as-spun state and 4–6 nm after annealing for 2 h at 400°C. The lattice parameter of the Cu-rich phase in the as-spun sample is 0.3608 nm and 0.3610 nm for the (Fe,Ni)-rich phase. After a 24-h annealing treatment at 600°C, the mean diameter of the particle is 20 nm and the lattice parameter of the (Fe,Ni)-rich phase has decreased to 0.3600 nm, while that of the Cu-rich phase has increased to 0.3613 nm, which is consistent with a segregation of Fe and Ni in the precipitates. The composition and volume fraction of the two phases measured for this annealed sample are in good agreement with the Thermocalc® predictions.     

Generation of Soft Ferrite Nanoparticles by Pulsed Laser Ablation in Liquids

We generate Mn–ferrite nanoparticles (NPs) by Nd:YAG (1064 nm) laser irradiation in distilled water. We characterize such NPs in terms of the size distribution, shape and chemical composition using transmission electron microscopy (TEM), energy-dispersive X rays (EDS), and Fourier-transform infrared spectroscopy (FTIR). Using a magnetic force microscope (MFM), we show the magnetic properties of the generated nanoparticles.     

Synthesis of nitrogen-doped single-walled carbon nanotubes and monitoring of doping by Raman spectroscopy

Nitrogen-doped single-walled carbon nanotubes （CNx-SWNTs） with tunable dopant concentrations were synthesized by chemical vapor deposition （CVD）, and their structure and elemental composition were characterized by using transmission electron microscopy （TEM） in combination with electron energy loss spectroscopy （EELS）. By comparing the Raman spectra of pristine and doped nanotubes, we observed the doping-induced Raman G band phonon stiffening and 2D band phonon softening, both of which reflect doping-induced renormalization of the electron and phonon energies in the nan- otubes and behave as expected in accord with the n-type doping effect. On the basis of first principles calculations of the distribution of delocalized carrier density in both the pristine and doped nanotubes, we show how the n-type doping occurs when nitrogen heteroatoms are substitutionally incorporated into the honeycomb tube-shell carbon lattice.     

Focused ion beam milling and ultramicrotomy of mineralised ivory dentine for analytical transmission electron microscopy

The use of focused ion beam (FIB) milling for preparation of sections of mineralised ivory dentine for transmission electron microscopy (TEM) is investigated. Ivory dentine is essentially composed of fibrillar type-I collagen and apatite crystals. The aim of this project is to gain a clearer understanding of the relationship between the organic and inorganic components of ivory dentine using analytical TEM, in order to utilise these analytical techniques in the context of common skeletal diseases such as osteoporosis and arthritis. TEM sections were prepared in both single and dual beam FIB instruments, using two standard lift-out techniques, in situ and ex situ. The FIB sections were systematically compared with sections prepared by ultramicrotomy, the traditional preparation route in biological systems, in terms of structural and chemical differences. A clear advantage of FIB milling over ultramicrotomy is that dehydration, embedding and section flotation can be eliminated, so that partial mineral loss due to dissolution is avoided. The characteristic banding of collagen fibrils was clearly seen in FIB milled sections without the need for any chemical staining, as is commonly employed in ultramicrotomy. The FIB milling technique was able to produce high-quality TEM sections of ivory dentine, which are suitable for further investigation using electron energy-loss spectroscopy (EELS) and energy-filtering TEM (EFTEM) to probe the collagen/apatite interface.     

HAADF-STEM investigation of the structures of electrolytically deposited CoP and CoNiP alloys

The structure and chemical composition of electrolytically deposited films of CoP and CoNiP amorphous alloys are studied by means of high-angle annular dark-field scanning transmission electron microscopy in the z-contrast mode, and via EELS and EDS spectroscopy with high locality. It is shown that variations in chemical composition correlate with heterogeneities in film structure.     

High-Temperature Behavior of SiO2 at Grain Boundaries in TZP

The chemical reaction between SiO₂ and tetragonal zirconia polycrystal (TZP) was directly observed using a TEM in-situ heating technique in order to understand the behavior of SiO₂ in TZP at high temperatures. Their dynamic interaction was recorded up to about 1400°C using a CCD camera-video system connected to the TEM. Most of SiO₂ phase dissolved into the ZrO₂ grains above 1300°C. On the other hand, during cooling from the high temperature to around 400°C, amorphous SiO₂ reprecipitated from the surface of ZrO₂ grains and formed a thin layer around the ZrO₂ grains. This result agrees well with the fact that silicon segregates in the vicinity of grain boundaries in SiO₂-doped TZP. In order to confirm the grain boundary segregation at high temperatures, we investigated grain boundaries in quenched specimens by high resolution electron microscopy (HREM), energy dispersive X-ray spectroscopy (EDS) and electron energy-loss spectroscopy (EELS). It was found that no amorphous phase was present between two adjacent grains in the quenched samples. EDS analysis revealed that silicon segregated at the grain boundaries and that the segregation layer was wider than that in as-sintered specimens. The electron energy loss near edge structure (ELNES) of O K-edge was measured from both grain boundary and grain interior in quenched specimen, and their spectra were interpreted by a first principles molecular-orbital (MO) calculation using the discrete-variational (DV)-X method.     

Composition of the “GaAs” quantum dot,grown by droplet epitaxy

Self-assembled strain-free quantum dot (QD) structures were grown on AlGaAs surface by the droplet epitaxal method. The QDs were developed from pure Ga droplets under As pressure. The QDs were investigated by atomic force microscopy (AFM) and transmission electron microscopy (TEM). Both techniques show that the QDs are very uniform in size and their distribution on the surface is also homogeneous. The high resolution cross-sectional TEM investigation shows perfect lattice matching between the QD and the substrate, and also the faceting of the side walls of QD can be identified exactly by lattice planes. Analytical TEM (elemental mapping by EELS) unambiguously identifies the presence of Al in the QD.     

TEM characterization of chemically synthesized copper–gold nanoparticles

Dodecanethiol-capped Cu–Au nanoparticles, synthesized via a successive two-phase (water/toluene) and galvanic-exchange procedure, were characterized using transmission electron microscopy (TEM). The size range of the particles is around 1–7 nm. Electron-induced morphological evolution was observed under high resolution (HR) TEM. Cuboctahedral morphology was found to be thermodynamically stable. Electron-induced aggregation of two particles was also observed. Chemical ordering of cuboctahedral particles was studied by atomic-resolution high angle annular dark field (HAADF) imaging in scanning TEM (STEM) mode and energy dispersive X-ray (EDX) element mapping using a silicon drift detector (SDD). The particles were found to be Cu–Au mixed, and to be stable in air. Surface plasmon resonance (SPR), which is dependent on local structure and morphology, was investigated by electron energy loss spectroscopy (EELS).