等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

液晶二聚体

液晶二聚体作为半柔性主链型液晶聚合物的简化模型, 通过对其液晶性质的研究, 有助于理解更复杂聚合物体系的液晶行为. 另外, 液晶二聚体作为一类特殊的液晶也有其自身的相结构和相行为. 以分子结构与液晶态的相互关系为主线, 系统介绍了目前文献报道的对称及非对称棒状液晶二聚体(线形、H形、U形、T形)、盘状液晶二聚体(对称的盘-盘状液晶二聚体和非对称的盘-棒状液晶二聚体)和香蕉形液晶二聚体(对称的香蕉-香蕉形液晶二聚体和非对称的香蕉-棒状液晶二聚体)等各种不同类型的液晶二聚体的研究进展, 以期为新型液晶二聚体的分子设计提供一些借鉴.     

有机硅改性席夫碱聚氨酯型液晶固定相的制备、表征及色谱性能

以对苯二胺、3-氯丙醇和4-羟基苯甲醛为原料,合成对苯二(对苯丙氧基醇)亚胺液晶基元,再与对苯二异氰酸酯和1,3-双(3-氨基丙基)四甲基二硅氧烷反应,合成席夫碱型硅氧烷聚氨酯液晶聚合物。 通过红外光谱法、X射线衍射、热分析、偏光显微镜等技术手段对其结构和性能进行了表征。 结果表明,该物质为席夫碱有机硅聚氨酯液晶聚合物,属于近晶相液晶,液晶区间为103~150 ℃,热分解温度为300 ℃。 用席夫碱型硅氧烷聚氨酯液晶固定相制备填充色谱柱,考察固定液的相对极性及其对取代苯位置异构体的色谱分离性能。 合成的席夫碱型硅氧烷聚氨酯液晶聚合物的液晶温度范围为103~146 ℃,属于强极性固定液(P_x=79),各组分色谱峰的分离度为0.96~3.33。     

Polymer-Metal Nanoparticle Complexes for Improving the Performance of Liquid Crystal Displays

Summary: Here we applied metal nanoparticles as a dopant of liquid crystals. Since liquid crystal molecules are self-assembled, it is not so easy to disperse metal nanoparticles in liquid crystal media. We first prepared metal nanoparticles protected by liquid crystal molecules by reduction of metal ions in the presence of liquid crystal molecules. This liquid crystal molecule-protected metal nanoparticles can be easily dispersed in liquid crystal media to fabricate liquid crystal sol containing metal nanoparticles. A simple liquid crystal molecule, 4′-pentylbiphenyl-4-carbonitrile (abbreviated as 5CB) was used in the present experiments at first. 5CB sol containing metal nanoparticles could construct novel twisted nematic liquid crystal devices (TN-LCDs), which revealed the electrooptic properties depending on the kind of metal of nanoparticles. During the experiments we discovered that 5CB-protected metal nanoparticles could move in liquid crystal media by applying the voltage. This phenomenon is inconvenient for liquid crystal displays, especially those driven by a matrix of thin-film transistors (TFTs). In order to avoid this phenomenon, we prepared polymer-protected metal nanoparticles and applied them to liquid crystal devices, which provided good performance as the devices, i.e., low driving voltage, rapid response at low temperature, and so on.     

基于胆甾相液晶的可调制光子晶体

将胆甾相液晶填充进胶体晶体内部空隙, 通过胆甾相液晶与胶体晶体的耦合, 构建了一种新型可调制液晶光子晶体. 填充于胶体晶体内部的胆甾相液晶织构呈现典型的手性近晶相(S)特征. 由于胆甾相液晶具有特定的选择性反射, 当胶体晶体的带隙处于胆甾相液晶的反射波长范围之内, 则随着温度的改变, 胶体晶体的带隙与胆甾相液晶的带隙同时发生蓝移. 在一定温度条件下, 胆甾相液晶的带隙将与胶体晶体的带隙发生耦合, 实现了光子晶体带隙在单峰与双峰之间的可逆切换.     

Copolymerizable initiator for improved polymer dispersed liquid crystal films

The problems of photoinitiator contamination are addressed for the liquid crystal phase in polymer dispersed liquid crystal films formed by photopolymerization induced phase separation of liquid crystal from monomer solutions. Initiator contamination lowers the clearing point of the liquid crystal phase, and decreases the photostability and resistivity of the polymer dispersed liquid crystal. These problems are minimized by replacing the conventional photoinitiators with copolymerizable initiators which become incorporated in the polymer phase as it separates. Copolymerizable photoinitiators are studied and used to form polymer dispersed liquid crystals with higher clearing point liquid crystal phases, higher resistivity, and better photostability than polymer dispersed liquid crystals formed with conventional photoinitiators. These improvements provide very significant advantages for many polymer dispersed liquid crystal applications.     

近晶型聚硅氧烷侧链液晶的合成与表征

以烯丙基溴、对羟基苯甲酸、对氰基苯酚为主要原料合成了液晶基元对-烯丙氧基苯甲酸对-羟基苯氰酯,通过硅氢化加成反应将其接枝到聚甲基氢硅氧烷主链上,合成了一种新型的聚硅氧烷侧链液晶.通过傅里叶变换红外光谱仪(FT-IR)、氢核磁共振仪(1H-NMR)、差示扫描量热仪(DSC)、热台偏光显微镜(POM)和X-射线衍射仪(XR...     

Copolymerizable initiator for improved polymer dispersed liquid crystal films

Abstract

The problems of photoinitiator contamination are addressed for the liquid crystal phase in polymer dispersed liquid crystal films formed by photopolymerization induced phase separation of liquid crystal from monomer solutions. Initiator contamination lowers the clearing point of the liquid crystal phase, and decreases the photostability and resistivity of the polymer dispersed liquid crystal. These problems are minimized by replacing the conventional photoinitiators with copolymerizable initiators which become incorporated in the polymer phase as it separates. Copolymerizable photoinitiators are studied and used to form polymer dispersed liquid crystals with higher clearing point liquid crystal phases, higher resistivity, and better photostability than polymer dispersed liquid crystals formed with conventional photoinitiators. These improvements provide very significant advantages for many polymer dispersed liquid crystal applications.     

Igepal CO系列表面活性剂溶致液晶的结构特性

对壬基酚聚氧乙烯醚（IgepalCO）系列表面活性剂,生成何种溶致液晶与其EO基团数n有关,而在何浓度范围内生成溶致液晶则与生成溶致液晶的最低水含量及最大水增溶量有关．EO基团数n小于10时,生成层状液晶,n大于10时则生成六角状液晶,层状液晶两亲双层内,水与表面活性剂的最低摩尔比rmin和最高摩尔比rmax随EO基团数n增加分别是非线型增加与线型增加,在IgepalCO520（n＝5）中加入IgepalCO710（n＝10．5）,对层状液晶的生成无显著影响,在IgepalCO710中加入IgepalCO520,则对六角状液晶的生成产生显著影响,出现了六角状液晶向层状液晶的转变。     

聚合物分散液晶膜

聚合物分散液晶膜是将液晶和聚合物结合,得到的一种综合性能优异的膜材料,液晶分子赋予了聚合物分散液晶膜显著的电光特性,使其受到了广泛的研究,并有着广阔的应用前景。而聚合物作为成膜材料,起着辅助但是重要的作用,其结构和固化过程是影响聚合物分散液晶膜电光特性的重要因素。本文简要综述了聚合物分散液晶膜的制备方法、电光特性的影响因素及研究手段。     

胆甾相液晶微胶囊制备与表征

为了实现液晶的分散、保护和致稳,完成了DYE液晶的包覆。对该方法所采用的芯壁比、乳化剂含量、剪切速度和剪切时间等影响微胶囊包覆因素做了研究。首先,用自由基聚合法制备了液晶微胶囊。接着,以偏光显微镜(POM)检验液晶微胶囊的包覆效果,即在液晶微胶囊经过加热前后,液晶是否仍然保持其独有的光学特性。然后,在分析比较SEM和激光粒度仪等评价方法的性能的基础上,说明了液晶微胶囊的形貌及粒径分布。最后,利用傅里叶变换红外光谱仪再次验证了液晶微胶囊的包覆效果。实验结果表明：当芯壁比为5:4时,剪切速度为7000 rpm,剪切时间为10 min,乳化剂HSMA含量为5 ml时,微胶囊的形貌及粒径分布最优,液晶微胶囊显色性能最优。研制的DYE液晶微胶囊具有单分散性好、显色性优、耐高温能力强等优点,并以此微胶囊制备了热至变色液晶膜。