The grafting of acrylamide onto poly(ε‐caprolactone) and poly(1,5‐dioxepan‐2‐one) using electron beam preirradiation. I. Influence of dose and Mohr's salt for the grafting onto poly(ε‐caprolactone)

Poly(ε‐caprolactone) films (TONE® 787) were irradiated by electron beam in air prior to grafting in aqueous solutions of acrylamide. The grafting kinetics and molecular weight of the grafted poly(acrylamide) chains were studied with irradiation doses between 2.5 and 20 Mrad and in the Mohr's salt concentration range of 0.0025–1 wt %. The grafting rate and yield were strongly dependent on the Mohr's salt concentration. By molecular weight analysis of grafted poly(acrylamide) chains, it was shown that the molecular weight is approximately proportional to the mass of the grafted PAAm. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1643–1649, 1999     

Collapse of Four-Arm Stars Polyelectrolyte Brushes Under An Electric Field in the Presence of Trivalent Salt Coions

Langevin dynamics simulations were conducted to study the collapse of grafted partially charged 4-arm star chains onto the oppositely charged grafting electrode in the presence of trivalent salt coions. Simulation results reveal that the average charge fraction of the grafted star chains and the salt concentration play critical roles in the competitive adsorption of charged monomers and trivalent salt coions onto the oppositely charged electrode. For grafted star chains with relatively high charge fraction, charged monomers are the dominant species collapsing on the oppositely charged electrode with the emergence of charge reversal on the grafting electrode. At a low charge fraction such that the total amount of charges on a grafted star molecule is comparable to that of a trivalent salt coion, trivalent salt coions absorb more strongly onto the electrode than grafted stars even at very low salt concentration. It is found that at relatively low charge fraction of star chains, the addition of trivalent salt coions does not lead to charge overcompensation of the surface charges on the grafting electrode. The stretching of star brushes under an electric field in the presence of trivalent salt coions was also briefly investigated.     

Effects of carbonyl and aldehyde groups in the graft copolymerization of methyl methacrylate on cellulose with a ceric salt

Graft copolymerization of methyl methacrylate on cellulosic materials of various carbonyl and aldehyde contents with the use of a ceric salt as an initiator was studied. It was found that the concentration of the ceric salt which gives the maximum per cent grafting is in good agreement with the equivalent of total carbonyl content in the cellulosic material, and the number of grafted chains in copolymers is roughly proportional to it. However, the molar ratio of the number of grafted chains to total carbonyl content is quite small, being approximately 1:50, and the graft copolymerization can be explained kinetically on the assumption that the number of radicals produced on cellulose by the ceric salt leading to branching is very much smaller than the number of radicals destroyed by the ceric salt, and growing radicals can be stabilized by the termination reaction with the ceric salt or with a cellulose radical. Although both aldehyde and carbonyl groups contribute to the formation of grafted chains, the former are effective mainly at low concentrations of the ceric salt; both groups participate in the production of graft copolymers showing the maximum per cent grafting.     

Crystallization and morphology of poly(ethylene‐2,6‐naphthalene dicarboxylate) in the presence of nucleating agents

The crystallization and morphology of poly(ethylene‐2,6‐naphthalene dicarboxylate) (PEN) containing, as nucleating agents, a sodium salt of a copolymer of ethylene and acrylic acid or a sodium salt of a copolymer of ethylene and methacrylic acid, were investigated with differential scanning calorimetry, polarized optical microscopy, and small‐angle light scattering. The nucleating agents accelerated the crystallization rate at high temperatures by decreasing the surface free energy barrier hindering nucleation. Meanwhile, the nucleating agents with flexible chains could also improve the mobility of the PEN chains and increase the crystallization rate at low temperatures. Hedrites were observed when PEN was crystallized at high temperatures, whereas crystallization at low temperatures led to the formation of spherulites. Similar but smaller morphologies were obtained in the presence of nucleating agents. With nucleating agents, the spherulites formed at low temperatures were less perfect, although the optical properties of the spherulites were not influenced. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2387–2394, 2002     

Mixed brushes consisting of oppositely charged Y-shaped polymers in salt free,monovalent, and divalent salt solutions

The conformation and the internal stratification of mixed brushes formed from oppositely charged Y(−) and Y(+)-shaped chains in salt free, monovalent, and divalent salt solutions were studied by means of molecular dynamics simulations using the primitive model. Scaling relations of mixed brush height with respect to the grafting surface per chain, the ratio of the total positive to the total negative charge of polyelectrolyte chains, and salt concentrations were obtained. The simulations predicted that mixed brushes show a unique response to divalent salt (1:2) solutions. For symmetric brushes having the same spacer lengths, number of chains and charged units fractions the increase of the salt concentration leads to the enrichment of the outer brush surface with Y(+) units and the lamella microphase separation. For asymmetric brushes in high salt concentration cylindrical domain microphases are formed.     

Molecular Size and Morphology of Single Chains of Poly(sulfobetaine methacrylate)

The effects of the concentration of sodium chloride in an aqueous solution(c_NaCl) and the temperature on the molecular size of poly(sulfobetaine methacrylate)(PSBMA) were studied via viscometry and dynamic light scattering(DLS). The morphology of single-chain PSBMA was determined by atomic force microscopy(AFM). The results demonstrate that the hydrodynamic diameter of PSBMA can be expressed as a continuous function of c_NaCl, with the molecular size of PSBMA increasing and eventually approaching an asymptotic value with increasing c_NaCl. The molecular size of PSBMA at a lower c_NaCl(0.04 mol/L) increases with increasing temperature, which is the opposite of the temperature effect at a higher c_NaCl(2.0 mol/L). Therefore, the internal structure of PSBMA chains in solutions with a low salt concentration differs from that in solutions with a high salt concentration. In addition, the morphology of single chains of PSBMA appears to be spherical, containing 89% void space, and the apparent size of the dried chains is almost identical to that in solution.     

Conformation of poly(styrene sulfonate) layers physisorbed from high salt solution studied by force measurements on two different length scales

The conformation of poly(styrene sulfonate) (PSS) layers physisorbed from 1 M NaCl is determined by force measurements and imaging on two length scales. With colloidal probe technique steric forces as predicted for neutral grafted brushes are observed. On decrease and increase of the NaCl concentration, the grafting density remains constant, yet the brush thickness swells and shrinks reversibly with the salt concentration with an exponent of -0.3. At low salt conditions, the brush length amounts to 30% of the contour length, a behavior known for polyelectrolyte brushes and attributed to the entropy of the counterions trapped in the brush. Between a PSS layer and a pure colloidal silica sphere, the same steric forces are observed, and additionally at large separations (beyond the range of the steric repulsion) an electrostatic force is found. A negatively charged AFM tip penetrates the brush--a repulsive electrostatic force between the tip and surface is found, and single chains can be imaged. Thus, with the nanometer-sized AFM tip, the flatly adsorbed fraction of the PSS chains is seen, whereas the micrometer-sized colloidal probe interacts with the fraction of the chains penetrating into solution.     

The effect of additives on radiation-induced grafting of AA and SSS onto HDPE

A kind of ion-exchange membrane with strong acid and weak acid groups was prepared by radiation-induced grafting of acrylic acid (AA) and sodium styrene sulfonate (SSS) onto high-density polyethylene membrane (HDPE). The effect of additives such as sodium acetate, sodium chloride on grafting yield was studied. It was found that for either pre-irradiation method or simultaneous radiation method, the weak acid salt of strong alkali sodium acetate had a complex effect on the grafting yield by “pH effect” and “ion pair effect”, and the neutral salt sodium chloride was helpful to the increase of grafting yield by “ion pair effect”.     

Cationic polymerization of α-methylstyrene from polydienes. I. Synthesis and characterization of poly(butadiene-g-α-methylstyrene) copolymers

The preparation of poly(butadiene-g-α-methylstyrene) copolymers was investigated with three different alkylaluminum coinitiators. The alkylaluminum compounds in conjunction with polybutadiene which contained a low concentration of labile chlorine atoms initiated the polymerization of α-methylstyrene to produce graft copolymers. Trimethylaluminum gave higher grafting efficiencies than diethylaluminum chloride at comparable monomer conversions. Triethylaluminum produced only very low monomer conversions (<5%), even at long reaction times, and for this reason was not studied extensively. The number of grafts per polybutadiene backbone was determined for a number of copolymers and found to increase slightly as the allylic chlorine concentration in the polybutadiene backbone was increased. In all cases, however, only a low percentage of the available labile chlorine sites along the polybutadiene backbone resulted in grafted α-methylstyrene side chains. The addition of small quantities of water to the polymerization solvent greatly enhanced the grafting rate and ultimate monomer conversion during the synthesis of these poly(butadiene-g-α-methylstyrene) copolymers. The mechanistic role of water during these grafting reactions is unknown at the present time.     

Radiation‐assisted controlled grafting and reaction parameter optimization of an industrially important polyolefin elastomer (POE)

Controlled (low degree) grafting of a polar group to a non‐polar polymer or reverse is an important means to change the polarity of the base polymer, maintaining the properties of the polymer. In the present study, a polar monomer, methacrylic acid (MAA), was grafted onto three different types of “Engages” (a special type of polyolefin elastomer) in aqueous medium by gamma radiation. Grafting parameters (total dose, MAA concentration, and Mohr's salt concentration) were optimized for the desired amount of low‐degree grafting (less than 15 wt%). The grafting yields were measured gravimetrically. Pure and grafted Engages were characterized by Fourier transformed infrared spectroscopy, contact angle measurement, and scanning electron microscope. Fourier transformed infrared spectroscopy spectra confirmed the successful grafting of MAA onto the Engages. For all three, the best yields were found at 3‐kGy gamma radiation dose, 25‐vol% MAA, and 20‐mM Mohr's salt concentration. The grafting efficiencies follow a descending trend like Engage 8150 > Engage 7447 > Engage 8003. From contact angle measurement, it was seen that the hydrophilicities of all Engage surfaces were increased after grafting. Scanning electron microscope illustrated the best distribution of grafted MAA molecules to be on Engage 8150 surface followed by Engage 7447 and Engage 8003, respectively. The tensile testing results suggested that the mechanical properties of the base polymers remained almost unchanged after grafting. Thus, without detrimenting any basic properties, polyolefin elastomers can be grafted to achieve desired yield by an environmental‐friendly method, gamma radiation grafting, in aqueous media. Copyright © 2016 John Wiley & Sons, Ltd.     

Ion-containing reverse osmosis membranes obtained by radiation grafting method

Cationic membranes obtained by radiation grafting of acqueous acrylic acid onto low density polyethylene films followed by alkaline treatment to confer ionic character in the graft chains, were tested for reverse osmosis desalination of saline water. Selected physical properties of such membranes were investigated. The grafted membranes prossess good mechanical and electrical properties. Water uptake for the alkali-treated membrane was much higher than that of the alkali-untreated one. The effect of operation time, degree of grafting, applied pressure and feed concentration on the water flux and salt rejection for the grafted membranes was investigated. Such cationic membranes showed good durability, thermal and chemical stability, acceptable water flux and salt rejection which may make them acceptable for practical use in reverse osmosis desalination of sea water.     

Synthesis of poly(styrene sulfonate) brushes.

Dense poly(styrene sulfonate sodium salt) brushes were prepared on silicone wafers using a two-step procedure: polystyrene (PS) chains, terminated by a reactive trichlorosilane group, were first covalently grafted, and then the PS brush was converted to a poly(styrene sulfonate) brush by a soft sulfonation reaction. Ellipsometry and infrared spectroscopy in ATR were used to characterize the samples and to optimize the procedure: in particular, the sulfonation was shown to be homogeneous along the chain backbone and the neutralization complete. In some cases, the polymer layer revealed to be quite fragile: the chains were pulled out of the brush. A consolidation treatment which consisted in grafting oligomers inbetween the long PS chains significantly increased the robustness of the layer. This might be relevant for industrial applications.     

Structure and electric properties of Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>-NaPO<Subscript>3</Subscript> glasses

The influence of the SO₄²⁻ ion on the temperature and concentration dependences of electric conductivity and the structure of sodium phosphate oxide glasses was studied. The increased electric conductivity of sulfate-phosphate glasses was explained by the formation of mixed sulfate-phosphate fragments with terminal SO₄²⁻ ions in the structure of glasses in the Na₂SO₄-NaPO₃ system. The dissociation energies of the sodium sulfate fragments are lower than those of pure oxide sodium phosphate structural units. As a result, the number of dissociated sodium ions increases, the activation energy of electric conductivity falls, and the conductivity (at 25°C) increases approximately 270-fold relative to the conductivity of NaPO₃. The arrangement of SO₄²⁻ ions in the structure was evaluated from the IR spectra of the glasses.     

甲基丙烯酸烷基磺酸钠在嵌段聚醚氨酯膜上接枝聚合的研究

本文对两种新合成的亲水性单体,甲基丙烯酸已磺酸钠和甲基丙烯酸辛磺酸钠在聚醚氨酯膜上接枝聚合进行了研究。其反应分两步:首先,在过氧化氢存在下,将膜进行光氧化,引入过氧化氢基团;然后,在还原剂亚铁盐作用下,引发甲基丙烯酸烷基磺酸酯接枝聚合。单体浓度、亚铁盐浓度、反应温度对接枝速率均有影响。接枝膜与基膜相比,吸水率与抗凝血性能均有提高。辛酯接枝膜的抗凝血性能显得更好。用扫描电镜可观察到膜上接枝物的图象。     

Synthesis and characterization of silica–polyvinyl imidazole core–shell nanoparticles via combination of RAFT polymerization and grafting‐to method

The silica–polyvinyl imidazole core–shell nanoparticles (silica/PVI NPs) with controlled shell thickness and narrow distribution size were fabricated via “grafting‐to” method. First, O‐ethyl xanthate terminated PVI with various chain lengths was produced via the reversible addition–fragmentation chain transfer (RAFT) polymerization using O‐ethyl‐S‐phenyl dithiocarbonate (EPDC) as RAFT agent. Next, three synthesized PVI of different molecular weights (3.4, 6.6, and 11 kg/mol) were successfully grafted to the methacrylate modified silica NPs from solution by radical mediated grafting‐to method. These core–shell NPs were then characterized by Fourier transform infrared spectroscopy (FTIR), X‐ray photoelectron spectrum measurements (XPS), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). Polyvinyl imidazole molecular weight, reaction time, polymer concentration, and reaction temperature were all used to control the grafting reaction for PVI grafting densities and shell thicknesses. The highest grafting density obtained was close to 1.2 chains/nm² and was achieved for 3.4 kg/mol PVI at 80°C. The prepared silica/PVINP displayed efficient antifouling properties and stability in concentrated sodium chloride aqueous solutions over a broad pH range for a period of at least 7 days. Copyright © 2017 John Wiley & Sons, Ltd.     

Study of the composition and properties of products formed in interaction of Na<Subscript>2</Subscript>CO<Subscript>3</Subscript> with proton-containing reagents

Composition and properties were studied of products formed in treatment of solid Na₂CO₃ with aqueous solutions containing acetic and citric acids with mass fractions of 0.40–0.60 and 0.33–0.49, respectively, at a Na₂CO₃/H _x An molar ratio of 2–6, where H _x An = CH₃COOH and H₃(C₆H₅O₇). It was found that the content of water in the systems under study and the strength of an acid affect the yield of the double salt of carbonic acid, Na₂CO₃·NaHCO₃·2H₂O and the composition of derivative proton-containing compounds. It is noted that sodium sesquicarbonate can be formed both by the crystallization mechanism and via a transformation of the primary structure of sodium carbonate. In the resulting powder-like products, water introduced with the acid solution is predominantly consumed for formation of crystal hydrates of carbonate-containing and derivative proton-containing compounds. The hygroscopic point of the resulting salt formulations was determined to be at a level of 70–75%. It was noted that sesquicarbonate-containing salt formulation formed in “dry” neutralization of sodium carbonate by acid solutions can be regarded as a builder for obtaining synthetic household detergents.     

Preparation of poly(ε-caprolactone)-co-poly(acrylic acid) by radiation-induced grafting

Acrylic acid was grafted onto poly(ε-caprolactone) (PCL) films by using electron beam (EB) preirradiation technique. The effect of reaction time, monomer concentration, radiation dose, time between irradiation and grafting, radiation atmosphere, and polymer crystallinity on the extent of grafting were studied. Silver and tin ions were attached to the grafted chains in order to study the grafting process. The irradiation in air was initially more rapid, but the final extent of grafting was the same when irradiated in nitrogen atmosphere. Maximum grafting extents exceeding 400% could be obtained. The optimal grafting was obtained at an acrylic acid to water ratio of 30 : 70. The grafting process could be initiated at a dose as low as 12 kGy. The grafting process proved to start at the surface and was extended into the bulk with time. The ability to form crystals was reduced as the grafting extent increased. The water uptake of the poly(ε-caprolactone)-graft-poly(acrylic acid) was increasing with increasing grafting extent, but reached a maximum of ca 100% for all grafting extents above 85%. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1805–1812, 1998     

Synthesis of sodium tungstate from the system Na<Subscript>2</Subscript>C<Subscript>2</Subscript>O<Subscript>4</Subscript>-NaNO<Subscript>3</Subscript>-WO<Subscript>3</Subscript>

The physicochemical basis of the heterogeneous reaction between the components of the system (sodium oxalate)-(sodium nitrate)-(tungsten(VI) oxide) has been studied. The reaction of WO₃ with sodium oxalate-nitrate mixtures occurs at a lower temperature and at a higher rate than the reaction with pure sodium carbonate. A high-yield process for the synthesis of high-purity sodium tungstate has been developed on the basis of this study.     

Multi-responsive properties of a poly(ethylene glycol)-grafted alternating copolymers of distyrenic monomer with maleic anhydride

A series of amphiphilic copolymers were synthesized by reversible addition-fragmentation chain transfer cyclocopolymerization of a styrenic monomer with maleic anhydride followed by grafting methoxy poly(ethylene glycol) onto the anhydride groups of the polymer chain. These amphiphilic graft copolymers exhibit multiple responsiveness toward temperature, pH, and selected cations in aqueous solutions. The cloud points (CP) of the graft copolymers increase with increasing length of the side chains and with increasing pH value of the solution. The addition of KCl and LiCl to the solutions had a salting-out effect lowering the CPs of the graft copolymers. The addition of NaCl, however, first raised the CP due to the complexation of the crown ether with Na(+) and then lowered the CP. The light scattering results confirmed an increase in phase transition temperature at lower concentrations of NaCl (5 and 10 mM) and then a decrease at a higher concentration of the sodium salt (100 mM).