Synthesis of spherical porous carbon by spray pyrolysis and its application in Li-S batteries

A spherical porous carbon (SPC) with high specific surface area is prepared by spray pyrolysis at 800 °C followed by removing silica template. The prepared SPC is employed as a conductive matrix in the sulfur cathode (S-SPC) for lithium–sulfur secondary batteries. The BET surface area of the prepared SPC sample is as high as 1,133 m² g^?1 and the total pore volume is 2.75 cm³ g^?1. The electrochemical evaluations including charge–discharge tests, cyclic voltammograms (CV), and electrochemical impedance spectrum suggest that the prepared S-SPC composite presents superior electrochemical stability when compared to the S-SP cathode. The as-prepared S-SPC composite shows improved cycle performance. The reversible discharge capacity is about 637 mAh g^?1 after 50 cycles, which is much better than that of the as-prepared sulfur–Super P carbon black composite. It may be attributed to the high porosity and excellent conductive structure of the SPC.     

Synthesis of γ-LiV2O5 nanorods as a high-performance cathode for Li ion battery

One-dimension γ-LiV₂O₅ nanorods were synthesized using VO₂(B) nanorods as precursor in this study. The as-prepared material is characterized by X-ray diffraction, X-ray photoelectron spectrometry, Fourier-transform infrared, transmission electron microscopy (TEM), cyclic voltammetry, and charge–discharge cycling test. TEM results show that LiV₂O₅ nanorods are 90–250 nm in diameter. The nanorods deliver a maximum discharge capacity of 284.3 mAh g^?1 at 15 mA g^?1 and 270.2 mAh g^?1 is maintained at the 15th cycle. Good rate performance is also observed with the discharge capacity of 250.1 and 202.6 mAh g^?1 at 50 and 300 mA g^?1, respectively. The capacity retention at 300 mA g^?1 is 84.2% over 50 cycles. The Li⁺ diffusion coefficient of LiV₂O₅ is calculated to be 10^-10–10^?9 cm² s^?1. It is demonstrated that the nanorod morphology could greatly facilitate to shorten lithium ion diffusion pathways and increase the contact area between active material and electrolyte, resulting in high capacity and rate performance for LiV₂O₅.     

Enhanced Performance of a Lithium–Sulfur Battery Using a Carbonate‐Based Electrolyte

The lithium–sulfur battery is regarded as one of the most promising candidates for lithium–metal batteries with high energy density. However, dendrite Li formation and low cycle efficiency of the Li anode as well as unstable sulfur based cathode still hinder its practical application. Herein a novel electrolyte (1 m LiODFB/EC‐DMC‐FEC) is designed not only to address the above problems of Li anode but also to match sulfur cathode perfectly, leading to extraordinary electrochemical performances. Using this electrolyte, lithium|lithium cells can cycle stably for above 2000 hours and the average Coulumbic efficiency reaches 98.8 %. Moreover, the Li–S battery delivers a reversible capacity of about 1400 mAh g^?1_sulfur with retention of 89 % for 1100 cycles at 1 C, and a capacity above 1100 mAh g^?1_sulfur at 10 C. The more advantages of this cell system are its outstanding cycle stability at 60 °C and no self‐discharge phenomena.     

Electrochemical studies of few-layered graphene as an anode material for Li ion batteries

Few-layered graphene (FLG) with specific surface area of only ~8.2 m² g^?1 was synthesized from graphene oxide (GO) using microwave-assisted exfoliation. GO was prepared using modified Hummers method. Few-layered nature of the exfoliated material was confirmed by electron microscopy, X-ray and electron diffraction, and Raman spectroscopy. Coin cells were fabricated using FLG as an anode and lithium metal as a counter electrode. The cells were tested using cyclic voltammetry and galvanostatic cycling techniques. FLG showed reversible capacity values of ~400 and ~250 mAh g^?1 at current rates of 0.1 and 1 C, respectively. Columbic efficiency was more than 98 % while cycle to cycle capacity fading was less than 2 %. Maximum discharge or charging capacity was below 0.3 V, a preferable characteristic for achieving ideal anodic behavior.     

Preparation and characterization of Li4Ti5O12 thin films by rapid thermal annealing

Li₄Ti₅O₁₂ thin films were prepared by solution deposition followed by rapid thermal annealing (RTA). The structural and electrochemical properties of the film were comparatively studied with the one prepared by conventional furnace annealing (CFA) through X-ray diffraction, scanning electron microscopy, cyclic voltammetry, galvanostatic lithium insertion–extraction experiments, and electrochemical impedance spectroscopy. The results show that the film prepared by RTA is homogeneous, crack-free, and pure spinel phase, and its grain size is smaller than that of the film prepared by CFA. The lithium extraction capacity of the film prepared by RTA is 59.5 μAh cm^?2 μm^?1, which is higher than 55.9 μAh cm^?2 μm^?1 of the film prepared by CFA. The capacity loss of the film prepared by RTA after being cycled 50 times is 3.1 %, which is 3.2 % lower than that of 6.3 % for the film prepared by CFA.     

Preparation and methane adsorption of two-dimensional carbide Ti<Subscript>2</Subscript>C

Here a novel material for methane adsorption was synthesized and studied, which is a graphene-like two-dimensional (2D) carbide (Ti₂C, a member of MXenes), formed by exfoliating Ti₂AlC powders in a solution of lithium fluoride (LiF) and hydrochloric acid (HCl) at 40 °C for 48 h. Based on first-principles calculation, theoretically perfect Ti₂C with O termination has a specific surface area (SSA) of 671 m² g^?1 and methane storage capacity is 22.9 wt%. Experimentally, 2.85 % exfoliated Ti₂C with mesopores shown methane capacity of 11.58 cm³ (STP: 0 °C, 1 bar) g^?1 (0.82 wt%) under 5 MPa and the SSA was 19.1 m² g^?1. For Ti₂C sample intercalated with NH₃·H₂O, the adsorbed amount was increased to 16.81 cm³ (STP) g^?1 at same temperature. At the temperature of 323 K, the adsorbed amount of as-prepared Ti₂C was increased to 52.76 cm³ (STP) g^?1. For fully exfoliated Ti₂C, the methane capacity was supposed to be 28.8 wt% or 1148 V (STP)v^?1. Ti₂C theoretically has much larger volume methane capacity than current methane storage materials, though its SSA is not very high.     

Lithium garnet based free-standing solid polymer composite membrane for rechargeable lithium battery

Electrolytes with high lithium-ion conductivity, better mechanical strength and large electrochemical window are essential for the realization of high-energy density lithium batteries. Polymer electrolytes are gaining interest due to their inherent flexibility and nonflammability over conventional liquid electrolytes. In this work, lithium garnet composite polymer electrolyte membrane (GCPEM) consisting of large molecular weight (W_avg ~?5?×?10⁶) polyethylene oxide (PEO) complexed with lithium perchlorate (LiClO₄) and lithium garnet oxide Li_6.28Al_0.24La₃Zr₂O₁₂ (Al-LLZO) is prepared by solution-casting method. Significant improvement in Li⁺ conductivity for Al-LLZO containing GCPEM is observed compared with the Al-LLZO free polymer membrane. Maximized room temperature (30 °C) Li⁺ conductivity of 4.40?×?10^?4 S cm^?1 and wide electrochemical window (4.5 V) is observed for PEO₈/LiClO₄?+?20 wt% Al-LLZO (GCPEM-20) membrane. The fabricated cell with LiCoO₂ as cathode, metallic lithium as anode and GCPEM-20 as electrolyte membrane delivers an initial charge/discharge capacity of 146 mAh g^?1/142 mAh g^?1 at 25 °C with 0.06 C-rate.     

Effect of crystallization route on the properties of LiMn2O4 thin films prepared by spin coating

LiMn₂O₄ thin films were prepared by spin coating through intermediate amorphous layer route (IALR) and intermediate crystallized layer route (ICLR). The phase identification, surface morphology, and electrochemical properties of the films prepared by different crystallization routes were studied by X-ray diffraction, scanning electron microscopy, and galvanostatic charge–discharge experiments. The results show that both films prepared by different crystallization routes are homogeneous and crack free. Compared with the film prepared by IALR, the film prepared by ICLR shows smaller grain size and is smoother and denser. The LiMn₂O₄ film prepared by ICLR delivers the specific capacity of 39.8 μAh?cm^?2?μm^?1, which is higher than 35.6 μAh?cm^?2?μm^?1 for the one prepared by IALR. The capacity loss of the film prepared by ICLR after being cycled 100 times is 3.4 %, which is smaller than that of 5.5 % for the film prepared by IALR. The film prepared by ICLR shows higher specific capacity and better cycling behavior than the one prepared by IALR.     

Optimising organic ionic plastic crystal electrolyte for all solid-state and higher than ambient temperature lithium batteries

Organic ionic plastic crystal (OIPC) electrolytes are among the key enabling materials for solid-state and higher than ambient temperature lithium batteries. This work overviews some of the parameter studies on the Li|OIPC interface using lithium symmetrical cells as well as the optimisation and performance of Li|OIPC|LiFePO₄ cells. The effects of temperature and electrolyte thickness on the cycle performance of the lithium symmetrical cell, particularly with respect to the interfacial and bulk resistances, are demonstrated. Whilst temperature change substantially alters both the interfacial and bulk resistance, changing the electrolyte thickness predominantly changes the bulk resistance only. In addition, an upper limit of the current density is demonstrated, above which irreversible processes related to electrolyte decomposition take place. Here, we demonstrate an excellent discharge capacity attained on LiFePO₄|10 mol% LiNTf₂-doped [C₂mpyr][NTf₂]|Li cell, reaching 126 mAh g^-1 at 50 °C (when the electrolyte is in its solid form) and 153 mAh g^-1 at 80 °C (when the electrolyte is in its liquid form). Most remarkably, at high temperature operation, the capacity retention at long cycles and high current is excellent with only a slight (3%) drop in discharge capacity upon increasing the current from 0.2 C to 0.5 C. These results highlight the real prospects for developing a lithium battery with high temperature performance that easily surpasses that achievable with even the best contemporary lithium-ion technology.     

Nanostructured Carbon/Antimony Composites as Anode Materials for Lithium‐Ion Batteries with Long Life

A series of nanostructured carbon/antimony composites have been successfully synthesized by a simple sol–gel, high‐temperature carbon thermal reduction process. In the carbon/antimony composites, antimony nanoparticles are homogeneously dispersed in the pyrolyzed nanoporous carbon matrix. As an anode material for lithium‐ion batteries, the C/Sb10 composite displays a high initial discharge capacity of 1214.6 mAh g^?1 and a reversible charge capacity of 595.5 mAh g^?1 with a corresponding coulombic efficiency of 49 % in the first cycle. In addition, it exhibits a high reversible discharge capacity of 466.2 mAh g^?1 at a current density of 100 mA g^?1 after 200 cycles and a high rate discharge capacity of 354.4 mAh g^?1 at a current density of 1000 mA g^?1. The excellent cycling stability and rate discharge performance of the C/Sb10 composite could be due to the uniform dispersion of antimony nanoparticles in the porous carbon matrix, which can buffer the volume expansion and maintain the integrity of the electrode during the charge–discharge cycles.     

The short-term cycling properties of Na/PVdF/S battery at ambient temperature

The Na/PVdF/S cells were composed of solid sodium, sulfur, and polyvinylidene fluoride–hexafluoropropene (PVdF) gel polymer electrolyte. The PVdF polymer electrolyte was prepared form tetraglyme plasticizer and NaCF₃SO₃ salt, and its electrochemical properties were studied using CV and impedance analysis. The interfacial resistance between sodium and polymer electrolyte increase with storage time, which might be associated with passivation layer. Solid-state sodium/sulfur cell using a PVdF gel polymer electrolyte has been tested. The Na/PVdF/S cell with 0.288 mA cm^?2 shows a high discharge capacity of 392 mAh g^?1 and 36 mAh g^?1 after 20 cycles. The cycle performance of Na/GPE/S cell operating at 25 °C is worse than Na/S cell at a high temperature.     

Electrochemical performance of LiVPO4F synthesized by ball-milling assisted sol-gel method

Lithium vanadium fluorophosphate, a cathode material for lithium-ion batteries, was synthesized by a ball-milling assisted sol-gel method. The micro structure, surface morphology and electrochemical performance of LiVPO₄F were investigated by X-ray diffraction (XRD), scanning electronic microscopy (SEM) and electrochemical tests. The results show that the sample synthesized at 550°C for 4 h was pure phase, possessed good crystallinity and uniform particle size distribution. At 0.1 C rate, the LiVPO₄F sample demonstrated charge and discharge capacity of about 153.2 and 125.7 mA h g^?1 at the first cycle respectively, the coulombic efficiency was 82%. The initial discharge capacity was 121.9 mA h g^?1 at the rate of 0.3 C, and it became 118.7 mA h g^?1 after 50 cycles.     

The electrochemical properties of Fe- and Ni-cosubstituted Li2MnO3 via combustion method

The Co-free Li_1.20Mn_0.54Ni _x Fe _y O₂ (x/y?=?0.5, 1.0, 2.0) materials were synthesized by combustion method. The effects of the preparation condition on the structure, morphology, and electrochemical performance were investigated by X-ray diffractometry, scanning electron microscopy, charge–discharge tests, and cyclic voltammetry (CV). The results indicate that the structure and electrochemical characteristics are sensitive to the preparation condition when a large amount of Fe is included. A pure layered α-NaFeO₂ structure with R-3m space group and the discharge capacities of over 200 mAh g^?1 were observed in some as-prepared cathode materials. Particularly, the Li_1.2Mn_0.54Ni_0.13Fe_0.13O₂ prepared by mixing an excess amount of lithium and by firing at 600 °C exhibits a second discharge capacity of 264 mAh g^?1 in the voltage range of 1.5–4.8 V under current density of 30 mA g^?1 at 30 °C and discharge capacity of 223 mAh g^?1 at 2.0–4.8 V. Nevertheless, an unpleasant capacity fading was observed and is primarily ascribed to transformation from a rock-layered structure into a spinel one according to CV testing.     

LiFePO4/C composites from carbothermal reduction method

Using the cheap raw materials lithium carbonate, iron phosphate, and carbon, LiFePO₄/C composite can be obtained from the carbothermal reduction method. X-ray diffraction (XRD) and scanning electronic microscope (SEM) observations were used to investigate the structure and morphology of LiFePO₄/C. The LiFePO₄ particles were coated by smaller carbon particles. LiFePO₄/C obtained at 750 °C presents good electrochemical performance with an initial discharge capacity of 133 mAh/g, capacity retention of 128 mAh/g after 20 cycles, and a diffusion coefficient of lithium ions in the LiFePO₄/C of 8.80?×?10^?13 cm²/s, which is just a little lower than that of LiFePO₄/C obtained from the solid-state reaction (9.20?×?10^?13 cm²/s) by using FeC₂O₄ as a precursor.     

Simple chemical route for nanorod-like cobalt oxide films for electrochemical energy storage applications

We used a simple chemical synthesis route to deposit nanorod-like cobalt oxide thin films on different substrates such as stainless steel (ss), indium tin oxide (ITO), and microscopic glass slides. The morphology of the films show that the films were uniformly spread having a nanorod-like structure with the length of the nanorods shortened on ss substrates. The electrochemical properties of the films deposited at different time intervals were studied using cyclic voltammetry (CV), galvanostatic charge–discharge (GCD), and electrochemical impedance spectroscopy (EIS). The film deposited after 20 cycles on ss gave the highest specific capacity of 67.6 mAh g^?1 and volumetric capacity of 123 mAh cm^?3 at a scan rate 5 mV s^?1 in comparison to 62.0 mAh g^?1 and 113 mAh cm^?3 obtained, respectively, for its counterpart on ITO. The film electrode deposited after 20 cycles on ITO gave the best rate capability and excellent cyclability with no depreciation after 2000 charge–discharge cycles.     

Preparation of Proton Conductive Inorganic-Organic Hybrid Films Using Epoxycyclohexylethyltrimethoxysilane and Orthophosphoric Acid

Proton conductive inorganic-organic hybrid films, which show high proton conductivity at temperatures higher than 100°C with low humidification, have been prepared from epoxycyclohexylethyltrimethoxysilane (EHTMS), 3-glycidoxypropyltrimethoxysilane, and orthophosphoric acid by the sol-gel method. Self-supporting, flexible, and brownish transparent films with a thickness ranging from 150 to 300 μm were obtained. Differential thermal analyses and thermogravimetric measurements revealed that the films were stable up to about 200°C. Ionic conductivity of the films increased with an increase in the content of phosphoric acid in the films. The films with a molar ratio of P/Si = 1.75 retained a high conductivity of about 6 × 10^?4 S cm^?1 even after holding for 150 h under 0.7% relative humidity at 130°C. The conductivity of the films increased with an increase in the relative humidity and was about 1 × 10^?2 S cm^?1 under 20% relative humidity at 130°C.     

Preparation of Li4Ti5O12 Yolk–Shell Powders by Spray Pyrolysis and their Electrochemical Properties

We have reported for the first time the preparation of yolk–shell‐structured Li₄Ti₅O₁₂ powders for use as anode materials in lithium‐ion batteries. One Li₄Ti₅O₁₂ yolk–shell‐particle powder is directly formed from each droplet containing lithium, titanium, and carbon components inside the hot wall reactor maintained at 900 °C. The precursor Li₄Ti₅O₁₂ yolk–shell‐particle powders, which are directly prepared by spray pyrolysis, have initial discharge and charge capacities of 155 and 122 mA h g^?1, respectively, at a current density of 175 mA g^?1. Post‐treatment of the yolk–shell‐particle powders at temperatures of 700 and 800 °C improves the initial discharge and charge capacities. The initial discharge capacities of the Li₄Ti₅O₁₂ powders with a yolk–shell structure and a dense structure post‐treated at 800 °C are 189 and 168 mA h g^?1, respectively. After 100 cycles, the corresponding capacities are 172 and 152 mA h g^?1, respectively (retentions of 91 and 90 %).     

Comparative study of LiMn2O4 thin film cathode grown at high, medium and low temperatures by pulsed laser deposition

LiMn₂O₄ thin films with different crystallizations were respectively grown at high, medium and low temperatures by pulsed laser deposition (PLD). Structures, morphologies and electrochemical properties of these three types of thin films were comparatively studied. Films grown at high temperature (?873 K) possessed flat and smooth surfaces and were highly crystallized with different textures and crystal sizes depending on the deposition pressure of oxygen. However, films deposited at low temperature (473 K) had rough surfaces with amorphous characteristics. At medium temperature (673 K), the film was found to consist mainly of nano-crystals less than 100 nm with relatively loose and rough surfaces, but very dense as observed from the cross-section. The film deposited at 873 K and 100 mTorr of oxygen showed an initial discharge capacity of 54.3 μAh/cm² μm and decayed at 0.28% per cycle, while the amorphous film had an initial discharge capacity of 20.2 μAh/cm² μm and a loss rate of 0.29% per cycle. Compared with the highly crystallized and the amorphous films, nano-crystalline film exhibited higher potential, more capacity and much better cycling stability. As high as 61 μAh/cm² μm of discharge capacity can be achieved with an average decaying rate of only 0.032% per cycle up to 500 cycles. The excellent performance of nano-crystalline film was correlated to its microstructures in the present study.     

A novel approach to massive preparation of LiV3O8 as a cathode material for lithium rechargeable battery

The layered cathode materials of LiV₃O₈ were successfully prepared for the lithium rechargeable battery via a wet-chemistry synthesis method. The as-synthesized materials were characterized by XRD (powder X-ray diffraction), SEM (scanning electron microscope) and galvanostatic charge-discharge test. The results indicate that this soft-synthesis technique offers reduced calcinations temperature, preferred surface morphology and better electrochemical performance. Among the thus-prepared materials, the material obtained at 350 °C demonstrates the first discharge capacity as high as 308 mAh g^-1 in the range of 4.0 ～1.7 V at a current rate of 30 mA g^-1 and remains at a stable discharge capacity of 250 mAh g^-1 within 30 cycles.     

Activated hierarchical porous carbon@π-conjugated polymer composite as cathode for high-performance lithium storage

Organic compounds become promising candidates for cathodes of rechargeable lithium battery (RLB) due to the high theoretical capacity and improved safety. However, they exhibit low conductivity and easy dissolution in electrolyte, which leads to the low utilization of active materials and poor cycling stability of RLBs. Here, we synthesize a novel composite of activated hierarchical porous carbon supporting poly(1,5-diamino-anthraquinone) (aHPC@PDAA), using Ce(SO₄)₂ as oxidant and naphthalenesulfonic acid (NSA) as soft template for PDAA. The as-synthesized composite exhibits uniformly nanoporous structure with nano-sized PDAA particles distributed homogenously inside and outside of pores. The aHPC@PDAA cathode for RLBs achieves high electrochemical performance with a discharge capacity as much as 250 mAh g^?1 at the current density of 100 mA g^?1, which still maintains 176 mAh g^?1 after 2000 charging-discharging cycles.