Oxidative Lime Pretreatment of Dacotah Switchgrass

Oxidative lime pretreatment increases the enzymatic digestibility of lignocellulosic biomass primarily by removing lignin. In this study, recommended pretreatment conditions (reaction temperature, oxygen pressure, lime loading, and time) were determined for Dacotah switchgrass. Glucan and xylan overall hydrolysis yields (72 h, 15 FPU/g raw glucan) were measured for 105 different reaction conditions involving three different reactor configurations (very short term, short term, and long term). The short-term reactor was the most productive. At the recommended pretreatment condition (120 °C, 6.89 bar O₂, 240 min), it achieved an overall glucan hydrolysis yield of 85.2 g glucan hydrolyzed/100 g raw glucan and an overall xylan yield of 50.1 g xylan hydrolyzed/100 g raw xylan. At this condition, glucan oligomers (1.80 g glucan recovered/100 g glucan in raw biomass) and xylan oligomers (25.20 g xylan recovered/100 g xylan in raw biomass) were recovered from the pretreatment liquor, which compensate for low pretreatment yields.     

Oxidative lime pretreatment of high-lignin biomass

Lime (Ca[OH]₂) and oxygen (O₂) were used to enhance the enzymatic digestibility of two kinds of high-lignin biomass: poplar wood and newspaper. The recommended pretreatment conditions for poplar wood are 150°C, 6 h, 0.1 g of Ca(OH)₂/g of dry biomass, 9 mL of water/g of dry biomass, 14.0 bar absolute oxygen, and a particle size of −10 mesh. Under these conditions, the 3-d reducing sugar yield of poplar wood using a cellulase loading of 5 filter paper units (FPU)/g of raw dry biomass increased from 62 to 565 mg of eq. glucose/g of raw dry biomass, and the 3-d total sugar (glucose + xylose) conversion increased from 6 to 77% of raw total sugars. At high cellulase loadings (e.g., 75 FPU/g of raw dry biomass), the 3-d total sugar conversion reached 97%. In a trial run with newspaper, using conditions of 140°C, 3 h, 0.3 g of Ca(OH)₂/g of dry biomass, 16 mL of water/g of dry biomass, and 7.1 bar absolute oxygen, the 3-d reducing sugar yield using a cellulase loading of 5 FPU/g of raw dry biomass increased from 240 to 565 mg of eq. glucose/g of raw dry biomass. A material balance study on poplar wood shows that oxidative lime pretreatment solubilized 38% of total biomass, including 78% of lignin and 49% of xylan; no glucan was removed. Ash increased because calcium was incorporated into biomass during the pretreatment. After oxidative lime pretreatment, about 21% of added lime could be recovered by CO₂ carbonation.     

Lime pretreatment of crop residues bagasse and wheat straw

Lime (calcium hydroxide) was used as a pretreatment agent to enhance the enzymatic digestibility of two common crop residues: bagasse and wheat straw. A systematic study of pretreatment conditions suggested that for short pretreatment times (1–3 h), high temperatures (85-135°C) were required to achieve high sugar yields, whereas for long pretreatment times (e.g., 24 h), low temperatures (50–65°C) were effective. The recommended lime loading is 0.1 g Ca(OH)₂/g dry biomass. Water loading had little effect on the digestibility. Under the recommended conditions, the 3-d reducing sugar yield of the pretreated bagasse increased from 153 to 659 mg Eq glucose/g dry biomass, and that of the pretreated wheat straw increased from 65 to 650 mg Eq glucose/g dry biomass. A material balance study on bagasse showed that the biomass yield after lime pretreatment is 93.6%. No glucan or xylan was removed from bagasse by the pretreatment, whereas 14% of lignin became solubilized. A lime recovery study showed that 86% of added calcium was removed from the pretreated bagasse by ten washings and could be recovered by carbonating the wash water with CO₂ at pH 9.5.     

Hydrolysis of Ammonia-pretreated Sugar Cane Bagasse with Cellulase, β-Glucosidase, and Hemicellulase Preparations

Sugar cane bagasse consists of hemicellulose (24%) and cellulose (38%), and bioconversion of both fractions to ethanol should be considered for a viable process. We have evaluated the hydrolysis of pretreated bagasse with combinations of cellulase, β-glucosidase, and hemicellulase. Ground bagasse was pretreated either by the AFEX process (2NH₃: 1 biomass, 100 °C, 30 min) or with NH₄OH (0.5 g NH₄OH of a 28% [v/v] per gram dry biomass; 160 °C, 60 min), and composition analysis showed that the glucan and xylan fractions remained largely intact. The enzyme activities of four commercial xylanase preparations and supernatants of four laboratory-grown fungi were determined and evaluated for their ability to boost xylan hydrolysis when added to cellulase and β-glucosidase (10 filter paper units [FPU]: 20 cellobiase units [CBU]/g glucan). At 1% glucan loading, the commercial enzyme preparations (added at 10% or 50% levels of total protein in the enzyme preparations) boosted xylan and glucan hydrolysis in both pretreated bagasse samples. Xylanase addition at 10% protein level also improved hydrolysis of xylan and glucan fractions up to 10% glucan loading (28% solids loading). Significant xylanase activity in enzyme cocktails appears to be required for improving hydrolysis of both glucan and xylan fractions of ammonia pretreated sugar cane bagasse.     

Kinetics of Lime Pretreatment of Sugarcane Bagasse to Enhance Enzymatic Hydrolysis

The objective of this work was to determine the optimum conditions of sugarcane bagasse pretreatment with lime to increase the enzymatic hydrolysis of the polysaccharide component and to study the delignification kinetics. The first stage was an evaluation of the influence of temperature, reaction time, and lime concentration in the pretreatment performance measured as glucose release after hydrolysis using a 2³ central composite design and response surface methodology. The maximum glucose yield was 228.45 mg/g raw biomass, corresponding to 409.9 mg/g raw biomass of total reducing sugars, with the pretreatment performed at 90°C, for 90 h, and with a lime loading of 0.4 g/g dry biomass. The enzymes loading was 5.0 FPU/dry pretreated biomass of cellulase and 1.0 CBU/dry pretreated biomass of β-glucosidase. Kinetic data of the pretreatment were evaluated at different temperatures (60°C, 70°C, 80°C, and 90°C), and a kinetic model for bagasse delignification with lime as a function of temperature was determined. Bagasse composition (cellulose, hemicellulose, and lignin) was measured, and the study has shown that 50% of the original material was solubilized, lignin and hemicellulose were selectively removed, but cellulose was not affected by lime pretreatment in mild temperatures (60–90°C). The delignification was highly dependent on temperature and duration of pretreatment.     

Optimization of dilute-acid pretreatment of corn stover using a high-solids percolation reactor

We have previously demonstrated that pretreatment of corn stover with dilute sulfuric acid can achieve high digestibility and efficient recovery of hemicellulose sugars with high yield and concentration. Further improvement of this process was sought in this work. A modification was made in the operation of the percolation reactor that the reactor is preheated under atmospheric pressure to remove moisture that causes autohydrolysis. This eliminated sugar decomposition during the preheating stage and led to a considerable improvement in overall sugar yield. In addition, liquid throughput was minimized to the extent that only one reactor void volume of liquid was collected. This was done to attain a high xylose concentration in the hydrolyzate. The optimum reaction and operating conditions were identified wherein near quantitative enzymatic digestibilities are obtained with enzyme loading of 15 FPU/g glucan. With a reduced enzyme loading of 5 FPU/g glucan, the enzymatic digestibility was decreased, but still reached a level of 92%. Decomposition of carbohydrates was extremely low as indicated by the measured glucan and xylan mass closures (recovered sugar plus unreacted) which were 98% and 94%, respectively. The data obtained in this work indicate that the digestibility is related to the extent of xylan removal.     

Potential of Agricultural Residues and Hay for Bioethanol Production

Production of bioethanol from agricultural residues and hays (wheat, barley, and triticale straws, and barley, triticale, pearl millet, and sweet sorghum hays) through a series of chemical pretreatment, enzymatic hydrolysis, and fermentation processes was investigated in this study. Composition analysis suggested that the agricultural straws and hays studied contained approximately 28.62-38.58% glucan, 11.19-20.78% xylan, and 22.01-27.57% lignin, making them good candidates for bioethanol production. Chemical pretreatment with sulfuric acid or sodium hydroxide at concentrations of 0.5, 1.0, and 2.0% indicated that concentration and treatment agent play a significant role during pretreatment. After 2.0% sulfuric acid pretreatment at 121 degrees C/15 psi for 60 min, 78.10-81.27% of the xylan in untreated feedstocks was solubilized, while 75.09-84.52% of the lignin was reduced after 2.0% sodium hydroxide pretreatment under similar conditions. Enzymatic hydrolysis of chemically pretreated (2.0% NaOH or H2SO4) solids with Celluclast 1.5 L-Novozym 188 (cellobiase) enzyme combination resulted in equal or higher glucan and xylan conversion than with Spezyme(R) CP- xylanase combination. The glucan and xylan conversions during hydrolysis with Celluclast 1.5 L-cellobiase at 40 FPU/g glucan were 78.09 to 100.36% and 74.03 to 84.89%, respectively. Increasing the enzyme loading from 40 to 60 FPU/g glucan did not significantly increase sugar yield. The ethanol yield after fermentation of the hydrolyzate from different feedstocks with Saccharomyces cerevisiae ranged from 0.27 to 0.34 g/g glucose or 52.00-65.82% of the theoretical maximum ethanol yield.     

Pretreatment of Rice Straw by a Hot-Compressed Water Process for Enzymatic Hydrolysis

Hot-compressed water (HCW) is among several cost-effective pretreatment processes of lignocellulosic biomass for enzymatic hydrolysis. The present work investigated the characteristics of HCW pretreatment of rice straw including sugar production and inhibitor formation in the liquid fraction and enzymatic hydrolysis of pretreated material. Pretreatment was carried out at a temperature ranging from 140 to 240 °C for 10 or 30 min. Soluble oligosaccharides were found to constitute almost all the components of total sugars in the liquid fraction. The maximal production of total glucose at 180 °C and below accounted for 4.4–4.9% of glucan in raw material. Total xylose production peaked at 180 °C, accounting for 43.3% of xylan in raw material for 10-min pretreatment and 29.8% for 30-min pretreatment. The production of acetic acid increased at higher temperatures and longer treatment time, indicating more significant disruption of lignocellulosic structure, and furfural production achieved the maximum (2.8 mg/ml) at 200 °C for both 10-min and 30-min processes. The glucose yield by enzymatic hydrolysis of pretreated rice straw was no less than 85% at 180 °C and above for 30-min pretreatment and at 200 °C and above for 10-min pretreatment. Considering sugar recovery, inhibitor formation, and process severity, it is recommended that a temperature of 180 °C for a time of 30 min can be the most efficient process for HCW pretreatment of rice straw.     

Enhancement of Enzymatic Hydrolysis and Klason Lignin Removal of Corn Stover Using Photocatalyst-Assisted Ammonia Pretreatment

Photocatalyst-assisted ammonia pretreatment was explored to improve lignin removal of the lignocellulosic biomass for effective sugar conversion. Corn stover was treated with 5.0–12.5 wt.% ammonium hydroxide, two different photocatalysts (TiO₂ and ZnO) in the presence of molecular oxygen in a batch reactor at 60 °C. Various solid-to-liquid ratios (1:20–1:50) were also tested. Ammonia pretreatment assisted by TiO₂-catalyzed photo-degradation removed 70 % of Klason lignin under the optimum condition (12.5 % ammonium hydroxide, 60 °C, 24 h, solid/liquid?=?1:20, photocatalyst/biomass?=?1:10 with oxygen atmosphere). The enzymatic digestibilities of pretreated corn stover were 85 % for glucan and 75 % for xylan with NH₃-TiO₂-treated solid and 82 % for glucan and 77 % for xylan with NH₃-ZnO-treated solid with 15 filter paper units/g-glucan of cellulase and 30 cellobiase units/g-glucan of β-glucosidase, a 2–13 % improvement over ammonia pretreatment alone.     

Dilute Ammonia Pretreatment of Sorghum and Its Effectiveness on Enzyme Hydrolysis and Ethanol Fermentation

A new pretreatment technology using dilute ammonium hydroxide was evaluated for ethanol production on sorghum. Sorghum fibers, ammonia, and water at a ratio of 1:0.14:8 were heated to 160 °C and held for 1 h under 140–160 psi pressure. Approximately, 44% lignin and 35% hemicellulose were removed during the process. Hydrolysis of untreated and dilute ammonia pretreated fibers was carried out at 10% dry solids at an enzyme concentration of 60 FPU Spezyme CP and 64 CBU Novozyme 188/g glucan. Cellulose digestibility was higher (84%) for ammonia pretreated sorghum as compared to untreated sorghum (38%). Fermentations with Saccharomyces cerevisiae D₅A resulted in 24 g ethanol /100 g dry biomass for dilute ammonia pretreated sorghum and 9 g ethanol /100 g dry biomass for untreated sorghum.     

Lime Pretreatment of Sugarcane Bagasse for Bioethanol Production

The pretreatment of sugarcane bagasse with lime (calcium hydroxide) is evaluated. The effect of lime pretreatment on digestibility was studied through analyses using central composite design (response surface), considering pretreatment time, temperature, and lime loading as factors. The responses evaluated were the yield of glucose from pretreated bagasse after enzymatic hydrolysis. Experiments were performed using the bagasse as it comes from an alcohol/sugar factory (non-screened bagasse) and bagasse in the size range from 0.248 to 1.397 mm (screened bagasse) (12-60 mesh). It was observed that the particle size presented influence in the release of fermentable sugars after enzymatic hydrolysis using low loading of cellulase and β-glucosidase (3.5 FPU/g dry pretreated biomass and 1.0 IU/g dry pretreated biomass, respectively).     

Relatively High-Substrate Consistency Hydrolysis of Steam-Pretreated Sweet Sorghum Bagasse at Relatively Low Cellulase Loading

Sweet sorghum bagasse (SSB) was steam pretreated in the conditions of 190 °C for 5 min to assess its amenability to the pretreatment and enzymatic hydrolysis. Results showed that pretreatment conditions were robust enough to pretreat SSB with maximum of 87% glucan and 72% xylan recovery. Subsequent enzymatic hydrolysis showed that the pretreated SSB at 2% substrate consistency resulted in maximum of 70% glucan-glucose conversion. Increasing substrate consistency from 2% to 16% led to a significant reduction in glucan conversion. However, the decrease ratio of glucan-glucose conversion was the minimum when the consistency increased from 2% to 12%. When the pretreated SSB consistency of 12% was applied for hydrolysis, increase in cellulase loading from 7.5 up to 20 filter paper units (FPU)/g glucan resulted only in 14% increase in glucan-glucose conversion compared to 20% increase with cellulase loading varying from 2.5 to 7.5 FPU/g glucan. More than 10 cellobiase units (CBU)/g glucan β-glucosidase supplementation had no noticeable improvement on glucan-glucose conversion. Additionally, supplementation of xylanase was found to significantly increase glucan-glucose conversion from 50% to 80% with the substrate consistency of 12%, when the cellulase and β-glucosidase loadings were at relatively low enzyme loadings (7.5 FPU/g and 10 CBU/g glucan). It appeared that residual xylan played a critical role in hindering the ease of hydrolysis of SSB. A proper xylanase addition was suggested to achieve a high hydrolysis yield at relatively high substrate consistency with relatively low enzyme loadings.     

Pretreatment of corn stover by soaking in aqueous ammonia at moderate temperatures

Soaking in aqueous ammonia at moderate temperatures was investigated as a method of pretreatment for enzymatic hydrolysis as well as simultaneous saccharification and cofermentation (SSCF) of corn stover. The method involves batch treatment of the feedstock with aqueous ammonia (15-30 wt%) at 40-90 degrees C for 6-24 h. The optimum treatment conditions were found to be 15 wt% of NH(3), 60 degrees C, 1:6 of solid-to-liquid ratio, and 12 h of treatment time. The treated corn stover retained 100% glucan and 85% of xylan, but removed 62% of lignin. The enzymatic digestibility of the glucan content increased from 17 to 85% with 15 FPU/g-glucan enzyme loading, whereas the digestibility of the xylan content increased to 78%. The treated corn stover was also subjected to SSCF test using Spezyme-CP and recombinant Escherichia coli (KO11). The SSCF of the soaking in aqueous ammonia treated corn stover resulted in an ethanol concentration of 19.2 g/L from 3% (w/v) glucan loading, which corresponds to 77% of the maximum theoretical yield based on glucan and xylan.     

Pretreatment of corn stover by soaking in aqueous ammonia

Soaking in aqueous ammonia (SAA) was investigated as a pretreatment method for corn stover. In this method, the feedstock was soaked in aqueous ammonia over an extended period (10–60 d) at room temperature. It was done without agitation at atmospheric pressure. SAA treatment removed 55–74% of the lignin, but retained nearly 100% of the glucan and 85% of the xylan. The xylan remaining in the corn stover after SAA treatment was hydrolyzed along with the glucan by xylanase present in the Spezyme CP enzyme. In the simultaneous saccharification and fermentation (SSF) test of SAA-treated corn stover, using S. cerevisiae (D₅A), an ethanol yield of 73% of theoretical maximum was obtained on the basis of the glucan content in the treated corn stover. The accumulation of xylose in the SSF appears to inhibit the cellulase activity on glucan hydrolysis, which limits the yield of ethanol. In the simultaneous saccharification and co-fermentation (SSCF) test, using recombinant E. coli (KO11), both the glucan and xylose were effectively utilized, resulting in on overall ethanol yield of 77% based on the glucan and xylan content of the substrate. When the SSCF process is used, the fact that the xylan fraction is retained during pretreatment is a desirable feature since the overall bioconversion can be carried out in a single step without separate recovery of xylose from the pretreatment liquid.     

Modeling of Pretreatment Condition of Extrusion-Pretreated Prairie Cordgrass and Corn Stover with Poly (Oxyethylen)20 Sorbitan Monolaurate

Extrusion processing has shown potential to be used as a pretreatment method for second-generation bioethanol production. Furthermore, surfactants have been shown to reduce enzyme deactivation and increase the efficiency of hydrolysis. Therefore, a sequential pretreatment technique was developed for corn stover (CS) and prairie cordgrass (PCG) in which a single screw extruder was used for the first pretreatment according to a previously optimized condition using 70?C180?°C for feed, barrel, and die zones with 65?C155?rpm screw speed. The second pretreatment was optimized in this study at 45?C55?°C, 1?C4?h, 0.15?C0.6?g Tween 20/g glucan according to response surface methodology. Optimization of surfactant pretreatment facilitated the estimation of interaction and higher-order effects for major factors involved in surfactant treatment (temperature, time, surfactant loading). Using 8.6?FPU/g glucan cellulase, the optimum conditions found by fitting appropriate quadratic models to the data increased glucose and xylose yield by 27.5 and 33?% for CS and by 21.5 and 27?% for PCG, respectively. Tween 20 concentrations and pretreatment temperature were the most significant factors affecting sugar yield (p value <0.05). Studies of SDS concentration at and beyond critical micelle concentration (5.2?C100?mM) demonstrated a decrease in sugar yield compared to control.     

Estimation of Treatment Time for Microbial Preprocessing of Biomass

Biochemical conversion of lignocellulosic biomass to ethanol involves size reduction, preprocessing, pretreatment, enzyme hydrolysis, and fermentation. In recent years, microbial preprocessing has been gaining attention as a means to produce labile biomass for lessening the requirement of pretreatment severity. However, loss of sugars due to microbial consumption is a major consequence, suggesting its minimization through optimization of nutrients, temperature, and preprocessing time. In this work, we emphasized estimation of fungal preprocessing time, at which higher sugar yields can be achieved after preprocessing and enzyme hydrolysis. The estimation is based on the enzymatic activity profile obtained by treating switchgrass with Phanerochaete chrysosporium for 28 days. Enzyme assays were conducted once in every 7 days for 28 days, for activities of phenol oxidase, peroxidase, β-glucosidase, β-xylosidase, and cellobiohydrolase. We found no activity for phenol oxidase and peroxidase, but the greatest activities for cellulases on the seventh day. We then treated switchgrass for 7 days with P. chrysosporium and observed that the preprocessed switchgrass had higher glucan (39%), xylan (17.5%), and total sugar yields (25.5%) than the unpreprocessed switchgrass (34%, 37.5%, and 20.5%, respectively, p < 0.05). This verifies the utility of using enzyme assays for initial estimation of preprocessing time to enhance sugar yields.     

Optimizing Dilute-Acid Pretreatment of Rapeseed Straw for Extraction of Hemicellulose

Biological conversion of biomass into fuels and chemicals requires hydrolysis of the polysaccharide fraction into monomeric sugars prior to fermentation. Hydrolysis can be performed enzymatically or with mineral acids. In this study, dilute sulfuric acid was used as a catalyst for the pretreatment of rapeseed straw. The purpose of this study is to optimize the pretreatment process in a 15-mL bomb tube reactor and investigate the effects of the acid concentration, temperature, and reaction time. These parameters influence hemicellulose removal and production of sugars (xylose, glucose, and arabinose) in the hydrolyzate as well as the formation of by-products (furfural, 5-hydroxymethylfurfural, and acetic acid). Statistical analysis was based on a model composition corresponding to a 3³ orthogonal factorial design and employed the response surface methodology to optimize the pretreatment conditions, aiming to attain maximum xylan, mannan, and galactan (XMG) extraction from hemicellulose of rapeseed straw. The obtained optimum conditions were: H₂SO₄ concentration of 1.76% and temperature of 152.6 °C with a reaction time of 21 min. Under these optimal conditions, 85.5% of the total sugar was recovered after acid hydrolysis (78.9% XMG and 6.6% glucan). The hydrolyzate contained 1.60 g/L glucose, 0.61 g/L arabinose, 10.49 g/L xylose, mannose, and galactose, 0.39 g/L cellobiose, 0.94 g/L fructose, 0.02 g/L 1,6-anhydro-glucose, 1.17 g/L formic acid, 2.94 g/L acetic acid, 0.04 g/L levulinic acid, 0.04 g/L 5-hydroxymethylfurfural, and 0.98 g/L furfural.     

Ammonia fiber explosion treatment of corn stover

Optimizing process conditions and parameters such as ammonia loading, moisture content of biomass, temperature, and residence time is necessary for maximum effectiveness of the ammonia fiber explosion process. Approximate optimal pretreatment conditions for corn stover were found to be temperature of 90°C, ammonia: dry corn stover mass ratio of 1∶1, moisture content of corn stover of 60% (dry weight basis), and residence time (holding at target temperature), of 5 min. Approximately 98% of the theoretical glucose yield was obtained during enzymatic hydrolysis of the optimal treated corn stover using 60 filter paper units (FPU) of cellulase enzyme/g of glucan (equal to 22 FPU/g of dry corn stover). The ethanol yield from this sample was increased up to 2.2 times over that of untreated sample. Lowering enzyme loading to 15 and 7.5 FPU/g of glucan did not significantly affect the glucose yield compared with 60 FPU, and any differences between effects at different enzyme levels decreased as the treatment temperature increased.     

Lime Pretreatment and Fermentation of Enzymatically Hydrolyzed Sugarcane Bagasse

Sugarcane bagasse was subjected to lime (calcium hydroxide) pretreatment and enzymatic hydrolysis for second-generation ethanol production. A central composite factorial design was performed to determine the best combination of pretreatment time, temperature, and lime loading, as well as to evaluate the influence of enzymatic loadings on hydrolysis conversion. The influence of increasing solids loading in the pretreatment and enzymatic hydrolysis stages was also determined. The hydrolysate was fermented using Saccharomyces cerevisiae in batch and continuous mode. In the continuous fermentation, the hydrolysates were concentrated with molasses. Lime pretreatment significantly increased the enzymatic digestibility of sugarcane bagasse without the need for prior particle size reduction. In the optimal pretreatment conditions (90 h, 90 °C, 0.47 g?lime/g bagasse) and industrially realistic conditions of hydrolysis (12.7 FPU/g of cellulase and 7.3 CBU/g of β-glucosidase), 139.6 kg?lignin/ton raw bagasse and 126.0 kg hemicellulose in the pretreatment liquor per ton raw bagasse were obtained. The hydrolysate from lime pretreated sugarcane bagasse presented low amounts of inhibitors, leading to ethanol yield of 164.1 kg?ethanol/ton raw bagasse.     

Pretreatment of sugarcane bagasse by acidified aqueous polyol solutions

Pretreatments of sugarcane bagasse by three high boiling-point polyol solutions were compared in acid-catalysed processes. Pretreatments by ethylene glycol (EG) and propylene glycol solutions containing 1.2 % H₂SO₄ and 10 % water at 130 °C for 30 min removed 89 % lignin from bagasse resulting in a glucan digestibility of 95 % with a cellulase loading of ~20 FPU/g glucan. Pretreatment by glycerol solution under the same conditions removed 57 % lignin with a glucan digestibility of 77 %. Further investigations with EG solutions showed that increases in acid content, pretreatment temperature and time, and decrease in water content improved pretreatment effectiveness. A good linear correlation of glucan digestibility with delignification was observed with R² = 0.984. Bagasse samples pretreated with EG solutions were characterised by scanning electron microscopy, Fourier transform infrared spectroscopy and X-ray diffraction, which confirmed that improved glucan enzymatic digestibility is mainly due to delignification and defibrillation of bagasse. Pretreatment by acidified EG solutions likely led to the formation of EG-glycosides. Up to 36 % of the total lignin was recovered from pretreatment hydrolysate, which may improve the pretreatment efficiency of recycled EG solution.