混频＋m腔微波电子枪束流动力学特性

为了使自由电子激光器的电子束注入器具有小的能散，小的横向发射度、高的亮度，本文提出在　腔的微波电子枪中采用混频腔技术，并用解析方法研究了混频加速的　腔方案的动力学特性，所导出的表达式说明此方案能改善束流的纵向和横向粒子动力学性能；为了对比，还借助于ＰＡＲＭＥＬＡ程序对此方案进行了束流动力学模拟，结论与导出的解析表达式结果一致．     

Experimental study of the possibility to increase the pitch factor of an intense relativistic helical electron beam

We present the results of experiments on the formation of a high-quality relativistic helical electron beam (HEB) in a magnetron-injection gun. It is shown that suppression of parasitic excitation of microwaves in the input part of the transportation channel allows eliminating high-voltage breakdowns in the gun and achieving greater beam compression. A modulation of the electron beam current at the frequency of longitudinal electron oscillations between the cathode and the magnetic mirror in the trap, which is related to the instability of the helical electron beam, has been observed for the first time. The modulation depth can reach tens percent. Pickup of reflected electrons by a special diaphragm makes it possible to increase the achievable pitch factor, eliminate the beam-current modulation and, as a result, form although with a current loss on the diaphragm, an HEB with record-breaking values of the pitch factor, which exceed 2. For a moderate HEB compression, when the portion of reflected electrons is relatively low, their pickup by the diaphragm allows one to form a beam in which the total energy of the transverse motion of electrons conserves despite the loss of part of the current. After the optimization, a beam with an electron energy of 300 keV, a current of 100 A, a pitch factor of 1.5, and a velocity spread of 20% is obtained for a 15% loss of the current on the diaphragm. Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Radiofizika, Vol. 51, No. 10, pp. 855–863, October 2008.     

大回旋cusp电子注数值模拟

 新一代宽带、高增益、大功率回旋行波管需要新型的电子注,而大回旋cusp电子注为其实现提供了可能。对大回旋cusp电子注进行系统理论分析,建立了大回旋cusp电子注的物理模型,在理论分析基础上进行了大量数值计算和模拟优化,并对大回旋cusp电子枪设计中的影响因素进行探讨。设计出一支低速度零散、高速度比、低纹波,适用于高次谐波的高功率(54 kV, 2.7 A)cusp电子枪。     

Experimental study of a powerful magnetron-injection gun for relativistic gyrodevices

We show that it is possible to increase significantly (up to one-half of the Langmuir value) the current of the electron beam in a magnetron-injection gun operated in the nonadiabatic regime of formation of a relativistic helical electron beam if the velocity spread is small. The obtained beam has a current of 200 A, a velocity spread of about 10%, a pitch factor of about 1, and an electron energy of 340 keV. __________ Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Radio.zika, Vol. 49, No. 8, pp. 680–685, August 2006.     

回旋速调管双阳极磁控注入电子枪的设计与优化

 根据8 mm回旋速调管放大器对双阳极磁控注入电子枪的要求,分析了电极形状、阳极电压、磁场、注电流对电子注横纵速度比和速度零散的影响,并进行了粒子模拟。分析表明：这些因素可归根为电场和磁场的作用,阴极附近高的电场有助于提高横纵速度比和降低速度零散;而高的磁场及低的磁压缩比将降低横纵速度比,但对速度零散影响无明显规律。在此基础上通过优化电极形状、磁场分布、电流、第一阳极电压和第二阳极电压,模拟并试制出工作电压65 kV、电流12 A、磁场1.4 T的双阳极电子枪,得到的横纵速度比值为1.4,横向速度零散为4.5%, 为8 mm回旋速调管提供了稳定高质量的电子注。     

Generation of beams of charged particles with transverse energy

The paper describes the operation and construction of an electron gun designed to form beams with variable transverse energy and a variable spread of magnetic moments. Transverse energy is acquired by the electrons as the beam passes through a weakly non-adiabatic magnetic step, and in an adiabatic motion through a growing magnetic field. The small spread of magnetic moments of the beam electrons is achieved by fulfilling the so-called focusing conditions which ensure that the spread of moments resulting from different initial radii of the particles is compensated by their initial radial velocities.     

100 MeV电子直线加速器的物理设计

 能量为100 MeV左右的高性能电子直线加速器是第三代同步辐射光源注入器和自由电子激光注入器的重要组成部分,采用热阴极栅控电子枪、聚束系统和4根SLAC型加速管作为加速器主体结构,一套45 MW的速调管调制器系统和波导系统作为微波功率源系统。设计中,使用了国际通用的模拟软件对加速器的动力学特性进行了数值模拟和参数优化,电子束能量达到100 MeV以上,能散小于1%,归一化发射度小于30 mm·mrad。     

Bunch length measurement at Tsinghua Thomson scattering X-ray source

The length of electron beam from a photocathode RF gun is determined by a spectrometer, according to the relative energy spread induced by the bunch length during the acceleration in a linac. For a photocathode RF gun, different laser injected phase and beam charge are studied. The compression is changed for the different laser phases, as from 10° to 30°, and the bunch length is lengthened due to the strong longitudinal space charge force, caused by the increased charge.     

热阴极微波电子枪的改进设计

 北京自由电子激光目前所用热阴极微波电子枪输出的电子束，在经过加速管加速后，位于微波脉冲前沿的电子束团存在能量偏高的现象，使得这部分电子无法对FEL增益做贡献。根据实验数据，分析了造成该现象的原因，提出一种可行的改进措施，即通过降低微波谐振腔的品质因数缩短建场时间，来消除该现象，以便提高整个装置的输出性能。     

Simulation study of a photo-injector for brightness improvement in Thomson scattering X-ray source via ballistic bunching

Increasing the peak brightness is beneficial to various applications of the Thomson scattering X-ray source. A higher peak brightness of the scattered X-ray pulse demands a shorter scattering electron beam realized by beam compression in the electron beam-line. In this article, we study the possibility of compressing the electron beam in a typical S-band normal conducting photo-injector via ballistic bunching, through just adding a short RF linac section right behind the RF gun, so as to improve the peak brightness of the scattered x-ray pulse. Numerical optimization by ASTRA demonstrates that the peak current can increase from 50 A to > 300 A for a 500 pC, 10 ps FWHM electron pulse, while normalized transverse RMS emittance and RMS energy spread increases very little. Correspondingly, the peak brightness of the Thomson scattering X-ray source is estimated to increase about three times.     

BEPCⅡ Positron Source

BEPCⅡ— an upgrade project of the Beijing Electron Positron Collider (BEPC) is a factory type of e^＋e^－ collider. The fundamental requirements for its injector linac are the beam energy of 1.89GeV for on-energy injection and a 40mA positron beam current at the linac end with a low beam emittance of 1.6μm and a low energy spread of ±0.5% so as to guarantee a higher injection rate (≥50mA/min) to the storage ring. Since the positron flux is proportional to the primary electron beam power on the target, we will increase the electron gun current from 4A to 10A by using a new electron gun system and increase the primary electron energy from 120MeV to 240MeV. The positron source itself is an extremely important system for producing more positrons, including a positron converter target chamber, a 12kA flux modulator, the 7m focusing module with DC power supplies and the support. The new positron production linac from the electron gun to the positron source has been installed into the tunnel. In what follows, we will emphasize the positron source design, manufacture and tests.     

Design studies on a 500 kV DC gun photo-injector for the BXERL test facility

BXERL is a proposal for a test facility(Beijing X-ray Energy Recovery Linac),which requires its injector to provide an electron beam of 5 MeV,77 pC/ bunch at a repetition rate of 130 MHz(average current of 10 mA).In this paper,we present the design of the injector,which consists of a 500 kV photocathodeDC gun equipped with a GaAs cathode preparation device,a 1.3 GHz normal conducting RF buncher,two solenoids,and one cryomodule containing two 1.3 GHz 2-cell superconducting RF cavities as the energy booster.The detailed beam dynamics show that the injector can generate electron bunches with a RMS normalized emittance of 1.49 7rmm-mrad,a bunch length of 0.67 mm,a beam energy of 5 MeV and an energy spread of 0.72%.     

低速度零散会切电子枪的设计和数值仿真

根据拉格朗日方程对电子在平滑会切磁场中的径向波动与速度零散的关系进行讨论。运用Matlab,Magic软件相互结合的方法设计电子枪结构和磁场。用Matlab程序模拟单电子在给定电场、磁场中的运动,分析了单电子径向速度对零散的影响,并优化磁场分布。设计的磁场可以有效地减小单电子束径向速度,降低电子束速度零散。用Magic软件对电流为1 A、能量为30 keV的电子束在优化磁场中的运动进行仿真,得到的电子束速度比约为2,速度零散小于2.5%,轴向速度零散小于8.5%。     

Improvement of the helical electron beam quality and the gyrotron efficiency by controlling the electric field distribution near a magnetron injection gun

A technique for controlling the electric field distribution near the cathode of a magnetron injection gun is developed. The feasibility of improving the quality of a helical electron beam by optimizing the electric field distribution in a pulsed 4-mm-wave gyrotron is studied theoretically and experimentally. Field distributions are obtained that minimize the electron velocity spread in the beam, coefficient of electron reflection from a magnetic mirror, and intensity of parasitic low-frequency oscillations. It is demonstrated that the gyrotron efficiency can be increased through a rise in the beam quality at the optimized electric field distribution.     

Analysis of the triode gun and the beam dynamics of a standing waveelectron linac

The charge-density integral method is used to analyse a triode gun which will inject electrons into a standing wave electron linac. The effect of space charge on the gun output beam parameters is estimated. The beam dynamics of the entire linac system is studied. The energy spectrum, beam size and divergence at the end of the linac are evaluated neglecting space charge     

8 mm二次谐波回旋速调管放大器双阳极磁控注入电子枪的设计

 计算了8 mm二次谐波回旋速调管双阳极电子枪的设计参数，根据这些参数，采用EGUN软件进行模拟和优化，设计出了一只双阳极磁控注入电子枪，该枪的电子束纵横速度比为1.45，速度零散为5.4%，并讨论了电极形状、磁场分布、电流、控制极电压和第二阳极电压对电子注性能的影响，结果发现电子注对这些影响因子非常敏感，设计中应对它们进行充分优化。     

回旋管单阳极电子枪计算机辅助设计

 根据回旋管对电子枪的要求，采用综合法和分析法设计了该单阳极磁控注入电子枪。编制了一套大型的计算程序，利用计算机辅助设计，给出了电极形状、电子轨迹与电子注参量。计算表明，这种电子枪具有速度零散小、层流性较好、体积小等特点。该枪已用于制管实验中。由热测实验表明，它具有明显的优点，并获得了127kW的峰值功率和超过10%的效率。     

大回旋电子束双磁会切电子枪的设计

 分析了Ka波段二次谐波回旋行波管双磁会切电子枪的理论模型,计算了电子枪的设计参数;采用EGUN软件进行模拟,设计出了产生大回旋电子束的双磁会切电子枪。该枪电压为70 kV,电流为3.35 A,电子束横纵速度比为1.62,速度零散为4.2%。给出了电子束速度比、速度零散沿轴线的分布,进而讨论了阳极电压对电子束性能的影响,结果表明选择适当的阳极电压和阴极磁场对得到好的电子束参量作用明显。     

L波段强流单束团注入器的束流动力学计算

自由电子激光器要求高亮度、低能散度的电子束注入波荡器(Undulator)。本文叙述提供高亮度电子束的高频电子直线加速器中的注入器部分的设计计算。注入器由L波段(1300MHz)的十二分频和三分频两个谐振腔预聚束器和一个基波频率的变相速聚束器组成。粒子运动方程中考虑了空间电荷效应和束流负载效应。电子枪的注入参数:脉冲宽度T=4ns;电流I=5A;电子的初始动能E_0=100keV;电子束分布为高斯型。参数优化设计结果:单束团宽度小于25ps,峰值电流达400A以上,电子的平均归一化能量>4,束团内的能量差小于200keV。     

170 GHz回旋管大束流双阳极磁控注入电子枪的分析及设计

 基于绝热压缩原理和强流电子光学理论,设计了一只170 GHz回旋管双阳极磁控注入电子枪,经过理论分析及计算,采用仿真软件进行模拟和优化,最终得到的电子枪的电子注速度比为1.31,横向速度零散度为3.5%,纵向速度零散度为6.1%,束电流为51 A。讨论了阴极磁场、控制阳极电压和第二阳极电压等因素对电子注性能的影响,发现电子注的速度比和速度零散度对这些影响因子的变化都非常敏感:随着阴极磁场的增大,电子注的速度比减小,纵向速度零散度先增大后减小,横向速度零散度先减小后增大;阳极角越接近阴极倾角,纵向速度零散度越小;阳极角向着减小阴阳极间距的方向变化时横向速度零散度变小;增大第一阳极电压可以增大电子注的速度比和电子注的速度零散度。在两阳极电压不变的情况下,增大阴阳极之间的距离会使电子注的速度零散度和电子注的速度比减小。