Pretreatment with ammonia water for enzymatic hydrolysis of corn husk, bagasse, and switchgrass

Bagasse, corn husk, and switchgrass were pretreated with ammonia water to enhance enzymatic hydrolysis. The sample (2 g) was mixed with 1–6 mL ammonia water (25–28% ammonia) and autoclaved at 120°C for 20 min. After treatment, the product was vacuum-dried to remove ammonia gas. The dried solid could be used immediately in the enzymatic hydrolysis without washing. The enzymatic hydrolysis was effectively improved with more than 0.5 and 1 mL ammonia water/g for corn husk and bagasse, respectively. In bagasse, glucose, xylose, and xylobiose were the main products. The adsorption of CMCase and xylanase was related to the initial rate of enzymatic hydrolysis. In corn husks, arabinoxylan extracted by pretreatment was substantially unhydrolyzed because of the high ratio of arabinose to xylose (0.6). The carbohydrate yields from cellulose and hemicellulose were 72.9% and 82.4% in bagasse, and 86.2% and 91.9% in corn husk, respectively. The ammonia/water pretreatment also benefited from switchgrass (Miscanthus sinensis and Solidago altissima L.) hydrolysis.     

Soaking Pretreatment of Corn Stover for Bioethanol Production Followed by Anaerobic Digestion Process

The production of ethanol and methane from corn stover (CS) was investigated in a biorefinery process. Initially, a novel soaking pretreatment (NaOH and aqueous-ammonia) for CS was developed to remove lignin, swell the biomass, and improve enzymatic digestibility. Based on the sugar yield during enzymatic hydrolysis, the optimal pretreatment conditions were 1?% NaOH?+?8?% NH₄OH, 50°C, 48?h, with a solid-to-liquid ratio 1:10. The results demonstrated that soaking pretreatment removed 63.6?% lignin while reserving most of the carbohydrates. After enzymatic hydrolysis, the yields of glucose and xylose were 78.5?% and 69.3?%, respectively. The simultaneous saccharification and fermentation of pretreated CS using Pichia stipitis resulted in an ethanol concentration of 36.1?g/L, corresponding only to 63.3?% of the theoretical maximum. In order to simplify the process and reduce the capital cost, the liquid fraction of the pretreatment was used to re-soak new CS. For methane production, the re-soaked CS and the residues of SSF were anaerobically digested for 120?days. Fifteen grams CS were converted to 1.9?g of ethanol and 1337.3?mL of methane in the entire process.     

Potential of Potassium Hydroxide Pretreatment of Switchgrass for Fermentable Sugar Production

Chemical pretreatment of lignocellulosic biomass has been extensively investigated for sugar generation and subsequent fuel production. Alkaline pretreatment has emerged as one of the popular chemical pretreatment methods, but most attempts thus far have utilized NaOH for the pretreatment process. This study aimed at investigating the potential of potassium hydroxide (KOH) as a viable alternative alkaline reagent for lignocellulosic pretreatment based on its different reactivity patterns compared to NaOH. Performer switchgrass was pretreated at KOH concentrations of 0.5–2 % for varying treatment times of 6–48 h, 6–24 h, and 0.25–1 h at 21, 50, and 121 °C, respectively. The pretreatments resulted in the highest percent sugar retention of 99.26 % at 0.5 %, 21 °C, 12 h while delignification up to 55.4 % was observed with 2 % KOH, 121 °C, 1 h. Six pretreatment conditions were selected for subsequent enzymatic hydrolysis with Cellic CTec2® for sugar generation. The pretreatment condition of 0.5 % KOH, 24 h, 21 °C was determined to be the most effective as it utilized the least amount of KOH while generating 582.4 mg sugar/g raw biomass for a corresponding percent carbohydrate conversion of 91.8 %.     

Oxidative Lime Pretreatment of Alamo Switchgrass

Previous studies have shown that oxidative lime pretreatment is an effective delignification method that improves the enzymatic digestibility of many biomass feedstocks. The purpose of this work is to determine the recommended oxidative lime pretreatment conditions (reaction temperature, time, pressure, and lime loading) for Alamo switchgrass (Panicum virgatum). Enzymatic hydrolysis of glucan and xylan was used to determine the performance of the 52 studied pretreatment conditions. The recommended condition (110°C, 6.89 bar O₂, 240 min, 0.248 g Ca(OH)₂/g biomass) achieved glucan and xylan overall yields (grams of sugar hydrolyzed/100 g sugar in raw biomass, 15 filter paper units (FPU)/g raw glucan) of 85.9 and 52.2, respectively. In addition, some glucan oligomers (2.6 g glucan recovered/100 g glucan in raw biomass) and significant levels of xylan oligomers (26.0 g xylan recovered/100 g xylan in raw biomass) were recovered from the pretreatment liquor. Combining a decrystallization technique (ball milling) with oxidative lime pretreatment further improved the overall glucan yield to 90.0 (7 FPU/g raw glucan).     

Enzymatic Hydrolysis of Sodium Dodecyl Sulphate (SDS)—Pretreated Newspaper for Cellulosic Ethanol Production by Saccharomyces cerevisiae and Pichia stipitis

Fermentation of enzymatic hydrolysate of waste newspaper was investigated for cellulosic ethanol production in this study. Various nonionic and ionic surfactants were applied for waste newspaper pretreatment to increase the enzymatic digestibility. The surfactant-pretreated newspaper was enzymatically digested in 0.05 M sodium citrate buffer (pH 4.8) with varying solid content, filter paper unit loading (FPU/g newspaper), and ratio of filter paper unit/β-glucosidase unit (FPU/CBU). Newspaper pretreated with the anionic surfactant sodium dodecyl sulphate (SDS) demonstrated the highest sugar yield. The addition of Tween-80 in the enzymatic hydrolysis process enhanced the enzymatic digestibility of newspaper pretreated with all of the surfactants. Enzymatic hydrolysis of SDS-pretreated newspaper with 15% solid content, 15 FPU/g newspaper, and FPU/CBU of 1:4 resulted in a newspaper hydrolysate conditioning 29.07 g/L glucose and 4.08 g/L xylose after 72 h of incubation at 50 °C. The fermentation of the enzymatic hydrolysate with Saccharomyces cerevisiae, Pichia stipitis, and their co-culture produced 14.29, 13.45, and 14.03 g/L of ethanol, respectively. Their corresponding ethanol yields were 0.43, 0.41, and 0.42 g/g.     

Combined steam pretreatment and enzymatic hydrolysis of starch-free wheat fibers

Steam treatment of an industrial process stream, denoted starch-free wheat fiber, was investigated to improve the formation of monomeric sugars in subsequent enzymatic hydrolysis for further bioconversion into ethanol. The solid fraction in the process stream, derived from a combined starch and ethanol factory, was rich in arabinose (21.1%), xylose (30.1%), and glucose (18.6%), in the form of polysaccharides. Various conditions of steam pretreatment (170–220°C for 5–30 min) were evaluated, and their effect was assessed by enzymatic hydrolysis with 2 g of Celluclast + Ultraflo mixture/ 100 g of starch-free fiber (SFF) slurry at 5% dry matter (DM). The highest overall sugar yield for the combined steam pretreatment and enzymatic hydrolysis, 52g/100 g of DM of SFF, corresponding to 74% of the theoretical, was achieved with pretreatment at 190°C for 10 min followed by enzymatic hydrolysis.     

Lime Pretreatment of Sugarcane Bagasse for Bioethanol Production

The pretreatment of sugarcane bagasse with lime (calcium hydroxide) is evaluated. The effect of lime pretreatment on digestibility was studied through analyses using central composite design (response surface), considering pretreatment time, temperature, and lime loading as factors. The responses evaluated were the yield of glucose from pretreated bagasse after enzymatic hydrolysis. Experiments were performed using the bagasse as it comes from an alcohol/sugar factory (non-screened bagasse) and bagasse in the size range from 0.248 to 1.397 mm (screened bagasse) (12-60 mesh). It was observed that the particle size presented influence in the release of fermentable sugars after enzymatic hydrolysis using low loading of cellulase and β-glucosidase (3.5 FPU/g dry pretreated biomass and 1.0 IU/g dry pretreated biomass, respectively).     

Microbial Lipid Production from Corn Stover via Mortierella isabellina

Microbial lipid is a promising source of oil to produce biofuel if it can be generated from lignocellulosic materials. Mortierella isabellina is a filamentous fungal species featuring high content of oil in its cell biomass. In this work, M. isabellina was studied for lipid production from corn stover. The experimental results showed that M. isabellina could grow on different kinds of carbon sources including xylose and acetate, and the lipid content reached to 35 % at C/N ratio of 20. With dilution, M. isabellina could endure inhibition effects by dilute acid pretreatment of corn stover (0.3 g/L furfural, 1.2 g/L HMF, and 1 g/L 4-hydroxybenozic acid) and the strain formed pellets in the cell cultivations. An integrated process was developed combining the dilute acid pretreatment, cellulase hydrolysis, and cell cultivation for M. isabellina to convert corn stover to oil containing fungal biomass. With 7.5 % pretreated biomass solid loading ratio, the final lipid yield from sugar in pretreated biomass was 40 % and the final lipid concentration of the culture reached to 6.46 g/L.     

Oxidative Lime Pretreatment of Dacotah Switchgrass

Oxidative lime pretreatment increases the enzymatic digestibility of lignocellulosic biomass primarily by removing lignin. In this study, recommended pretreatment conditions (reaction temperature, oxygen pressure, lime loading, and time) were determined for Dacotah switchgrass. Glucan and xylan overall hydrolysis yields (72 h, 15 FPU/g raw glucan) were measured for 105 different reaction conditions involving three different reactor configurations (very short term, short term, and long term). The short-term reactor was the most productive. At the recommended pretreatment condition (120 °C, 6.89 bar O₂, 240 min), it achieved an overall glucan hydrolysis yield of 85.2 g glucan hydrolyzed/100 g raw glucan and an overall xylan yield of 50.1 g xylan hydrolyzed/100 g raw xylan. At this condition, glucan oligomers (1.80 g glucan recovered/100 g glucan in raw biomass) and xylan oligomers (25.20 g xylan recovered/100 g xylan in raw biomass) were recovered from the pretreatment liquor, which compensate for low pretreatment yields.     

Oxidative lime pretreatment of high-lignin biomass

Lime (Ca[OH]₂) and oxygen (O₂) were used to enhance the enzymatic digestibility of two kinds of high-lignin biomass: poplar wood and newspaper. The recommended pretreatment conditions for poplar wood are 150°C, 6 h, 0.1 g of Ca(OH)₂/g of dry biomass, 9 mL of water/g of dry biomass, 14.0 bar absolute oxygen, and a particle size of −10 mesh. Under these conditions, the 3-d reducing sugar yield of poplar wood using a cellulase loading of 5 filter paper units (FPU)/g of raw dry biomass increased from 62 to 565 mg of eq. glucose/g of raw dry biomass, and the 3-d total sugar (glucose + xylose) conversion increased from 6 to 77% of raw total sugars. At high cellulase loadings (e.g., 75 FPU/g of raw dry biomass), the 3-d total sugar conversion reached 97%. In a trial run with newspaper, using conditions of 140°C, 3 h, 0.3 g of Ca(OH)₂/g of dry biomass, 16 mL of water/g of dry biomass, and 7.1 bar absolute oxygen, the 3-d reducing sugar yield using a cellulase loading of 5 FPU/g of raw dry biomass increased from 240 to 565 mg of eq. glucose/g of raw dry biomass. A material balance study on poplar wood shows that oxidative lime pretreatment solubilized 38% of total biomass, including 78% of lignin and 49% of xylan; no glucan was removed. Ash increased because calcium was incorporated into biomass during the pretreatment. After oxidative lime pretreatment, about 21% of added lime could be recovered by CO₂ carbonation.     

Evaluation of Ethanol Production from Corncob Using Scheffersomyces (Pichia) stipitis CBS 6054 by Volumetric Scale-up

In scale-up, the potential of ethanol production by dilute sulfuric acid pretreatment using corncob was investigated. Pretreatments were performed at 170 °C with various acid concentrations ranging from 0% to 1.656% based on oven dry weight. Following pretreatment, pretreated biomass yield ranged from 59% to 67%. More than 90% of xylan was removed at 0.828% of sulfuric acid. At same pretreatment condition, the highest glucose yield obtained from pretreated biomass by enzymatic hydrolysis was about 76%, based on a glucan content of 37/100 g. In hydrolysate obtained by pretreatment, glucose concentration was low, while xylose concentration was significantly increased above 0.368% of sulfuric acid. At 1.656% of sulfuric acid, xylose and glucose concentration was highest. In subsequent, fermentation with hydrolysate, maximal ethanol yield was attained after 24 h with 0.368% of sulfuric acid. The fermentation efficiency of hydrolysate obtained by enzymatic hydrolysis reached a maximum of 75% at an acid charge of 0.368%.     

Pretreatment of corn stover using wet oxidation to enhance enzymatic digestibility

Corn stover is an abundant, promising raw material for fuel ethanol production. Although it has a high cellulose content, without pretreatment it resists enzymatic hydrolysis, like most lignocellulosic materials. Wet oxidation (water, oxygen, mild alkali or acid, elevated temperature and pressure) was investigated to enhance the enzymatic digestibility of corn stover. Six different combinations of reaction temperature, time, and pH were applied. The best conditions (60g/L of corn stover, 195°C, 15 min, 12 bar O₂, 2 g/L of Na₂CO₃) increased the enzymatic conversion of corn stover four times, compared to untreated material. Under these conditions 60% of hemicellulose and 30% of lignin were solubilized, whereas 90% of cellulose remained in the solid fraction. After 24-h hydrolysis at 50°C using 25 filter paper units (FPU)/g of dry matter (DM) biomass, the achieved conversion of cellulose to glucose was about 85%. Decreasing the hydrolysis temperature to 40°C increased hydrolysis time from 24 to 72 h. Decreasing the enzyme loading to 5 FPU/g of DM biomass slightly decreased the enzymatic conversion from 83.4 to 71%. Thus, enzyme loading can be reduced without significantly affecting the efficiency of hydrolysis, an important economical aspect.     

Evaluation and Optimization of Organic Acid Pretreatment of Cotton Gin Waste for Enzymatic Hydrolysis and Bioethanol Production

This paper investigates the efficiency of the organic acids on the pretreatment of an industrially generated cotton gin waste for the removal of lignin, thereby releasing cellulose and hemicellulose as fermentable sugar components. Cotton gin waste was pretreated with various organic acids namely lactic acid, oxalic acid, citric acid, and maleic acid. Among these, maleic acid was found to be the most efficient producing maximum xylose sugar (126.05?±?0.74 g/g) at the optimum pretreatment condition of 150 °C, 500 mM, and 45 min. The pretreatment efficiency was comparable to the conventional dilute sulfuric acid pretreatment. A lignin removal of 88% was achieved by treating maleic acid pretreated biomass in a mixture of sodium sulfite and sodium chlorite. The pretreated biomass was further evaluated for the release of sugar by enzymatic hydrolysis and subsequently bioethanol production from hydrolysates. The maximum 686.13 g/g saccharification yield was achieved with maleic acid pretreated biomass which was slightly higher than the sulfuric acid (675.26 g/g) pretreated waste. The fermentation of mixed hydrolysates(41.75 g/l) produced 18.74 g/l bioethanol concentration with 2.25 g/l/h ethanol productivity and 0.48 g/g ethanol yield using sequential use of Saccharomyces cerevisiae and Pichia stipitis yeast strains. The production of bioethanol was higher than the ethanol produced using co-culture in comparison to sequential culture. Thus, it has been demonstrated that the maleic acid pretreatment and fermentation using sequential use of yeast strains are efficient for bioethanol production from cotton gin waste.     

Enhancement of enzymatic hydrolysis of corncob by microwave-assisted alkali pretreatment and its effect in morphology

Bioethanol produced from a conventional fermentation process using Saccharomyces cerevisiae utilizing pretreated and hydrolyzed corncob as a substrate was studied. It was found that the morphology of corncob was significantly changed after microwave-assisted alkali pretreatment was applied. An increase in the crystallinity index and surface area of the pretreated corncob was also observed. The highest total sugar concentration of 683.97 mg/g of pretreated corncob, or 45.60 g L^?1, was obtained from the optimum pretreatment conditions of 2 % NaOH at 100 °C for 30 min in a microwave oven. Microwave-assisted alkali pretreatment was an efficient way to improve the enzymatic hydrolysis accessibility of corncob in a shorter amount of time and at a lower temperature, compared to other methods.     

Optimization of steam pretreatment of SO2-impregnated corn stover for fuel ethanol production

In this study, corn stover with a dry matter content of 20% was impregnated with SO₂ and then steam pretreated for various times at various temperatures. The pretreatment was evaluated by enzymatic hydrolysis of the solid material and analysis of the sugar content in the liquid. The maximum overall yield of glucose, 89% of the theoretical based on the glucan in the raw material, was achieved when the corn stover was pretreated at 200°C for 10 min. The maximum overall yield of xylose, 78%, was obtained with pretreatment at 190°C for 5 min.     

Sequential Extrusion-Ozone Pretreatment of Switchgrass and Big Bluestem

Pretreatment is one of the biggest challenges in utilizing lignocellulosic feedstocks to meet the mandatory requirements for biofuels around the world. Earlier researchers evaluated extrusion and ozone pretreatment separately and found that sugar recovery can be improved significantly from 15–20 to 40–75 % for different feedstocks. To further improve sugar recoveries, extrusion-ozone sequential pretreatment was explored. Accordingly, optimal extruded switchgrass (176?°C, 155 rpm, 20 % moisture, and 8 mm) and big bluestem (180?°C, 155 rpm, 20 % moisture, and 8 mm) at 25–75 % moisture content were exposed to an ozone flow rate of 37–365 mg/h for 2.5 to 10 min. Pretreated samples were then subjected to enzymatic hydrolysis to determine sugar recovery. Statistical analyses confirmed significant effects of the independent variables and their interactions on sugar recoveries for both feedstocks. Maximum glucose, xylose, and total sugar recovery of 66.4, 82.3, and 70.4 %, respectively, were obtained when a low-moisture (25 %) extruded switchgrass was ozonated for 2.5 min at a flow rate of 37 mg/h. Respectively, this represents increases of 3.42, 5.01, and 3.42 times that of the control. When big bluestem at 25 % moisture was extruded and then ozonated for 2.5 min at a flow rate of 365 mg/h, resulting glucose, xylose, and total sugar recoveries of 90.8, 92.2, and 87.5 %, respectively, were obtained. These represent increases of 4.5, 2.7, and 3.9 times than that of the control. It is also noteworthy that furfural and hydroxymethyl furfural were not detected in any of the pretreatments, and only low levels (0.14–0.18 g/l) of acetic acid were measured. The results show that sequential pretreatment using extrusion and ozone is an efficient way to improve sugar recovery from herbaceous biomass feedstocks.     

Hydrothermal pretreatment conditions to enhance ethanol production from poplar biomass

Pretreatment has been recognized as a key step in enzyme-based conversion processes of lignocellulose biomass to ethanol. The aim of this study is to evaluate two hydrothermal pretreatments (steam explosion and liquid hot water) to enhance ethanol production from poplar (Populus nigra) biomass by a simultaneous saccharification and fermentation (SSF) process. The composition of liquid and solid fractions obtained after pretreatment, enzymatic digestibility, and ethanol production of poplar biomass pretreated at different experimental conditions was analyzed. The best results were obtained in steam explosion pretreatment at 210°C and 4 min, taking into account cellulose recovery above 95%, enzymatic hydrolysis yield of about 60%, SSF yield of 60% of theoretical, and 41% xylose recovery in the liquid fraction. Large particles can be used for poplar biomass in both pretreatments, since no significant effect of particle size on enzymatic hydrolysis and SSF was obtained.     

Effect of pretreatment severity on the enzymatic hydrolysis of bamboo in hydrothermal deconstruction

Bamboo was subjected to hydrothermal deconstruction to release xylans for the enhancement of enzymatic hydrolysis. The de-waxed and de-starched bamboo culm was non-isothermally pretreated in a batch reactor at a solid to liquid ratio of 1:10 g/mL at 120–240 °C. With the increase of the maximum heating temperature from 120 to 240 °C, the pH value of the liquor decreased from 5.98 to 2.71. A maximum yield of the non-volatile components in the liquid was achieved at a pretreatment severity of 4.20. With the increase of the pretreatment severity from 1.18 to 4.82, the yield of the solid residue decreased from 99.52 to 59.91 %, accompanying a decrease of xylan content from 28.86 to 0 %, an increase of glucan content from 42.80 to 59.14 % and an increase of lignin content from 28.10 to 40.57 %. The solid residues after the hydrothermal pretreatment were comprehensively characterized by FT IR, XRD, and element analysis. Enzymatic hydrolysis of the solid residues was assayed by commercial cellulase. Under enzymatic hydrolysis for 96 h, the enzymatic hydrolysis of the pretreated bamboo at the pretreatment severity of 4.82 was 81.16 %, which equaled to 4.7 times of that of the untreated bamboo. This study provided an environmentally friendly process to pretreat biomass for the production of energy.     

Application of xylanase from thermomyces lanuginosus IOC-4145 for enzymatic hydrolysis of corncob and sugarcane bagasse

Xylanases have significant current and potential uses for several industries including paper and pulp, food, and biofuel. For the biofuel industry, xylanases can be used to aid in the conversion of lignocellulose to fermentable sugars (e.g., xylose). We investigated the thermophilic fungus Thermomyces lanuginosus was yielded for xylanase production and found that the highest activity (850 U/mL) was yielded after 96 h of semisolid fermentation. The enzyme was used for hydrolyzing agricultural residues with and without pretreatment. Such residues were characterized in relation to the maximum xylose content by total acid hydrolysis. The highest xylose yields realized by enzymatic hydrolysis were 24 and 52%, achieved by using 3000 U/g (dried material) of sugarcane bagasse and corncob, respectively, which received both alkali and thermal pretreatment.     

Summary of findings from the Biomass Refining Consortium for Applied Fundamentals and Innovation (CAFI): corn stover pretreatment

The Biomass Refining Consortium for Applied Fundamentals and Innovation, with members from Auburn University, Dartmouth College, Michigan State University, the National Renewable Energy Laboratory, Purdue University, Texas A&M University, the University of British Columbia, and the University of California at Riverside, has developed comparative data on the conversion of corn stover to sugars by several leading pretreatment technologies. These technologies include ammonia fiber expansion pretreatment, ammonia recycle percolation pretreatment, dilute sulfuric acid pretreatment, flowthrough pretreatment (hot water or dilute acid), lime pretreatment, controlled pH hot water pretreatment, and sulfur dioxide steam explosion pretreatment. Over the course of two separate USDA- and DOE-funded projects, these pretreatment technologies were applied to two different corn stover batches, followed by enzymatic hydrolysis of the remaining solids from each pretreatment technology using identical enzyme preparations, enzyme loadings, and enzymatic hydrolysis assays. Identical analytical methods and a consistent material balance methodology were employed to develop comparative sugar yield data for each pretreatment and subsequent enzymatic hydrolysis. Although there were differences in the profiles of sugar release, with the more acidic pretreatments releasing more xylose directly in the pretreatment step than the alkaline pretreatments, the overall glucose and xylose yields (monomers + oligomers) from combined pretreatment and enzymatic hydrolysis process steps were very similar for all of these leading pretreatment technologies. Some of the water-only and alkaline pretreatment technologies resulted in significant amounts of residual xylose oligomers still remaining after enzymatic hydrolysis that may require specialized enzyme preparations to fully convert xylose oligomers to monomers.