Hydrothermal and plasma nitrided electrospun carbon nanofibers for amperometric sensing of hydrogen peroxide

Microchimica Acta - A fluorometric method is presented for sensitive deternination of microRNA. It is making use of carbon dots (C-dots) loaded with a DNA probe as fluorophore and MnO2 nanosheets...     

The preparation and adsorption properties of electrospun aramid nanofibers

The focus of this work is the preparation of aramid nanofibers via electrospinning technology and the study of their adsorption properties. In this article, aramid nanofibers were prepared by electrospinning aramid fibers solution with the addition of lithium chloride (LiCl). It showed a good adsorption capacity when methylene blue (MB) was used as the model target. There were much larger adsorption amounts and faster kinetics of uptaking target species of electrospun aramid nanofibers to MB than that of electrospun polyethersulfone (PES) nanofibers. Compared with activated carbon, aramid nanofibers also have a much faster adsorption rate to MB. Aramid nanofibers were subsequently used to effectively remove endocrine disruptors such as bisphenol A (BPA), phenol (Phe), and p‐hydroquinone (BPhe) from their aqueous solutions. Additionally, molecule imprinted technology enhances aramid nanofibers with much higher adsorption amounts and special adsorption property for endocrine disruptors. These results showed that aramid nanofibers have the potential to be used in environmental applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Low-temperature adsorption of hydrogen on nanoporous aluminophosphates: effect of pore size

Several nanoporous aluminophosphates (AlPOs) have been used to analyze the effect of pore diameter on the hydrogen adsorption characteristics. The heat of adsorption and adsorption capacity per unit micropore volume increase with decreasing pore size. AlPOs with smaller micropores favorably adsorb hydrogen at relatively low pressures. This work demonstrates that small pore size and large micropore volume are beneficial for high hydrogen uptake.     

Methane adsorption on microporous carbon adsorbent with wide pore size distribution

Methane adsorption on a microporous carbon adsorbent with a bimodal pore size distribution is studied at temperatures of 303–333 K at pressures up to 30 MPa. The total micropore volume of the adsorbent, as determined by the Dubinin method, is as large as 1.02 cm³/g. Maximum values of methane adsorption of ≈18 mmol/g are attained at a temperature of 303 K and a pressure of 30 MPa. Methane adsorption isosteres are plotted based on experimental data, and adsorption equilibria at low temperatures are calculated using the linearity of the plots. Experimental isotherms of methane adsorption are compared with the isotherms calculated by the Dubinin–Nikolaev equation with variations in parameters E and n. Temperature dependences of these parameters are determined. Specific characteristics of methane adsorption accumulation are calculated.     

Functionalized electrospun carbon nanofibers for removal of cationic dye

Electrospun carbon nanofibers (ECNFs) have attracted significant attention in recent years as relatively inexpensive alternative to carbon nanotubes for adsorption organic pollutants. In this study, ECNFs were fabricated from polyacrylonitrile (PAN) using an electrospinning technique, followed by carbonization and oxidation via treatment with a H₂SO₄/HNO₃ mixture. The prepared oxidized electrospun carbon nanofibers (O-ECNFs) were characterized using scanning and transmission electron microscopy (SEM and TEM), Fourier transform infrared (FT-IR), Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). The O-ECNFs were used as nano-adsorbents for the adsorption of methylene blue (MB) from aqueous solution. The adsorption of MB by the O-ECNFs was studied as a function of pH, time, adsorbent dosage, MB concentration, and temperature. ECNF functionalization enhanced the adsorption capacity towards MB dye compared pristine ECNFs. Detailed analysis of the adsorption kinetics showed that the adsorption process followed a pseudo-second-order model. The adsorption isotherm was best fit by the Langmuir model. The thermodynamic results showed that MB adsorption onto the O-ECNFs was endothermic and spontaneous.     

Tuning the hydrogen and hydroxyl adsorption on Ru nanoparticles for hydrogen electrode reactions via size controlling

Controlling the particle size of catalyst to understand the active sites is the key to design efficient electrocatalysts toward hydrogen electrode reactions including hydrogen oxidation and evolution (HOR/HER). Herein, the hydrogen and hydroxyl adsorption on Ru/C could be effectively tuned for HOR/HER by simple controlling the particle sizes. It is found that the metallic Ru (Ru⁰) is the active site for HOR/HER, while oxidized Ru (Ru^x+) will hinder the adsorption and desorption of hydrogen on the catalyst. For the HOR, catalyst with small particles is more efficient, due to it is a three-phase interface reaction of gas on the surface of the catalyst. For the HER, the metallic state of Ru is crucial. The deconvolution of hydrogen peaks indicates that the catalytic sites with low hydrogen binding energy (HBE) shoulder the majority of the HOR activity. CO stripping curve further demonstrates that the stronger hydroxyl species (OH_ad) affinity is beneficial to promote the HOR performance. The results indicate that the design of efficient HOR/HER catalyst should focus on the balance between particle size and metallic states.     

Effects of fluorination modification on pore size controlled electrospun activated carbon fibers for high capacity methane storage

Electrospun carbon fibers were prepared as a methane storage medium. Chemical activation was carried out using potassium carbonate to develop the pore structure, which can provide sites for the uptake of methane, and then fluorination surface modification was conducted to enhance the capacity of storage. Chemical activation provided a highly microporous structure, which is beneficial for methane storage, with a high specific surface area greater than 2500 m²/g. The pore size distribution showed that the prepared samples have pore sizes in the range of 0.7–1.6 nm. The effect of fluorination surface modification was also investigated. The functional groups, which were confirmed by XPS analysis, played an important role in guiding methane gas into the carbon silt pores via the attractive force felt by the electrons in the methane molecules due to the high electronegativity of fluorine. Eventually, the methane uptake increased up to 18.1 wt.% by the synergetic effects of the highly developed micropore structure and the guiding of methane to carbon pores by fluorine.     

Ethane adsorption on microporous carbon adsorbent with a wide pore size distribution

Russian Chemical Bulletin - A microporous carbon adsorbent MPU-007 with a wide pore size distribution (specific micropore volume W0 calculated within the framework of the theory of micropore volume...     

Ordered porous carbon with tailored pore size for electrochemical hydrogen storage application

Ordered porous carbon with tailored pore size represents an innovative concept in electrochemical hydrogen storage. This work deals with physical characteristics and electrochemical hydrogen storage behavior of the ordered porous carbons with well-tailored pore size, synthesized by a replica technique using hexagonal mesoporous silica as templates. By using a mixture of two surfactants (HTAB and C16EO8) at different ratios, it is possible to control the wall thickness of silica and, consequently, the pore diameter of carbons within a narrow range of 2.1-2.8 nm. In addition, highly developed ultramicroporosity (pore size smaller than 0.7 nm), which plays a predominant role in hydrogen storage, can be produced in the ordered porous carbons. A discharge capacity of up to 527 mAh/g (corresponding to 1.95 wt % hydrogen storage) has been achieved in 6 M KOH for the ordered porous carbon. Furthermore, the ordered porous carbons also possess excellent capacity retainability after charge-discharge cycles and rate capability.     

Nonenzymatic hydrogen peroxide sensor based on a glassy carbon electrode modified with electrospun PdO-NiO composite nanofibers

A glassy carbon electrode was modified with PdO-NiO composite nanofibers (PdO-NiO-NFs) and applied to the electrocatalytic reduction of hydrogen peroxide (H₂O₂). The PdO-NiO-NFs were synthesized by electrospinning and subsequent thermal treatment, and then characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. Factors such as the composition and fraction of nanofibers, and of the applied potential were also studied. The sensor exhibits high sensitivity for H₂O₂ (583.43 μA?·?mM^?1?·?cm^?2), a wide linear range (from 5.0 μM to 19 mM), a low detection limit (2.94 μM at an SNR of 3), good long term stability, and is resistant to fouling.

Lignin bio-oil-based electrospun nanofibers with high substitution ratio property for potential carbon nanofibers applications

We reported a new approach for development of lignin bio-oil-based electrospun nanofibers (LENFs) that had high substitution ratio (up to 80 wt%) and good morphology. This approach was particularly unique and translatable as it used small molecule lignin bio-oil with high reactivity and low heterogeneity obtained via lignin depolymerization reaction to produce well-oriented LENFs. Firstly, effects of various blends solutions ratios and electrospinning parameters on the characteristics of the obtained LENFs were analyzed. The results showed that the optimal parameters that resulted in the best electrospun nanofibers were as follows: blend solution ratio, the 20 wt% blend solution containing 80 wt% straw lignin bio-oil (SLB) and 20 wt% polyacrylonitrile (PAN), flow rate, 1 mL/h, voltage, 20 kV, rotational speed, 500 r/min and the distance between needle and collection screen, 20 cm. Secondly, used the best LENFs, we also applied to prepare lignin bio-oil-based carbon nanofibers (LCNFs) and estimated its properties by scanning electron microscope (SEM), X-ray diffraction (XRD) patterns, Raman spectroscopy and tension testing. Our results demonstrated that compared with pure PAN carbon nanofibers (PCNFs), the as-prepared LCNFs had similar smooth surfaces, similar crystallinity and similar mechanical properties. This work can promote the utilization of lignin depolymerization main-products to produce lignin-based materials, while also help to reduce use of high-cost PAN.     

A nonenzymatic sensor for xanthine based on electrospun carbon nanofibers modified electrode

Xanthine (Xa) determination is of considerable importance in clinical analysis and food quality control. Therefore, a sensitive nonenzymatic amperometric sensor for Xa based on carbon nanofibers (CNFs) has been proposed. The CNFs, which were prepared by electrospinning technique and subsequent thermal treatment, were used to modify carbon paste electrode (CNF-CPE) to construct the amperometric sensor device without any oxidation pretreatment. In application to Xa electrochemical determination, the CNF-CPE exhibited high electrocatalytic activity and fast amperometric response. Various experimental parameters, such as pH and applied potential were optimized. Under the optimal conditions, the dynamic linear range of Xa was 0.03-21.19 μM (R = 0.9992) with the detection limit low to 20 nM (S/N = 3). With good selectivity and sensitivity, the present system was successfully applied to estimate the freshness of fish and determine Xa in human urine, which provides potential application in food quality control and clinical analysis.     

Experimental study on high-pressure adsorption of hydrogen on activated carbon

A systematic measurement of H2 adsorption on activated carbon over a wide scope of conditions was completed for the first time using a novel cryostat developed by the present authors. The equilibrium temperatures covered 77-298 K with the space of about 20 K, and the equilibrium pressures increased from 0 to about 7MPa. A set of adsorption/desorption isotherms was obtained by a standard volumetric method. This set of experimental data was fitted to all the well-known models of type-I isotherms, and Dubinin-Astakhov (D-A) equation was found to be the best-fit one On the basis of D-A model one can predict adsorption with relative error of ±4%. A 3-dimensional adsorption surface was also constructed, and the isosteric heat of adsorption was analytically determined. Except in the low pressure area, the calculated values agreed well with the experimental ones. Finally, the troubles encountered in applying D-A equation to supercritical adsorption is discussed.     

Salt induced irreversible protein adsorption with extremely high loadings on electrospun nanofibers

LiCl is a kosmotrope that generally promotes protein salvation in aqueous solutions. Herein we report that LiCl embedded in electrospun polymeric nanofibers interestingly induced an abnormal protein adsorption and substantially augmented the adsorption capacity of the fibers. As a result, equilibrium protein loadings reached over 64% (w/w) of the dry mass of fibers, 9-fold higher than that observed in the absence of the salt. The adsorption appeared to be irreversible such that little protein loss was observed even after washing the fibers vigorously with fresh buffer solutions. We further examined the application of such intensified protein adsorption for enzyme immobilization. Proteins including bovine serum albumin (BSA) and protamine were first adsorbed, followed by covalent attachment of an outer layer of an enzyme, α-chymotrypsin. Such a multilayer-structured nanofibrous enzyme exhibited extremely high stability with no obvious activity loss even after being incubated for 8 months at 4 °C in aqueous buffer solution. The LiCl induced irreversible protein adsorption, which has been largely ignored in previous studies with electrospun materials, rendering an interesting scenario of interfacial protein-material interactions. It also reveals a new mechanism in controlling and fabricating molecular interactions at interfaces for development of a broad range of biomaterials.     

Uniaxially aligned carbon nanofibers derived from electrospun precursor yarns

Unlike conventional electrospun polymer fibers deposited on a target electrode as a randomly oriented mesh, poly(p‐xylenetetrahydrothiophenium chloride) was electrospun into centimeters‐long yarns vertically on the surface of the electrode but parallel to the electric field. The diameter of the yarn was strongly affected by the concentration, spinning rate, and viscosity of the polymer solution, but less dependent on the applied voltage. The subsequent carbonization of thus‐electrospun yarns at 600–1000 °C resulted in uniaxially aligned carbon nanofibers with average diameters of 127–184 nm. On the basis of Raman spectra, the graphitic crystallite size and the molar fraction of graphite were estimated to be 1.2–1.4 and 0.21–0.24 nm, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 305–310, 2008     

Comparative study of hydrogen adsorption on carbon and BN nanotubes

The physisorption and chemisorption of hydrogen in BN nanotubes, investigated by density functional theory (DFT), were compared with carbon nanotubes. The physisorption of H2 on BN nanotubes is less favorable energetically than on carbon nanotubes; BN nanotubes cannot adsorb hydrogen molecules effectively in this manner. Chemisorption of H2 molecules on pristine BN nanotubes is endothermic. Consequently, perfect BN nanotubes are not good candidates for hydrogen storage by either mechanism. Other strategies must be utilized if BN nanotubes are to be employed as hydrogen storage media such as utilizing them as supporting media for hydrogen-absorbing metal nanoclusters.     

Calculation of pore size from adsorption data

Spherical pores (voids) with 1 to 6 round necks are used to estimate the probable disagreement between the average diameter and Kelvin equivalent size. This disagreement is due to the delay in irreversible capillary condensation in such pores [1, 2].     

Functionalized graphene oxide-reinforced electrospun carbon nanofibers as ultrathin supercapacitor electrode

Graphene oxide has been used widely as a starting precursor for applications that cater to the needs of tunable graphene. However, the hydrophilic characteristic limits their application, especially in a hydrophobic condition. Herein, a novel non-covalent surface modification approach towards graphene oxide was conducted via a UV-induced photo-polymerization technique that involves two major routes; a UV-sensitive initiator embedded via pi-pi interactions on the graphene planar rings, and the polymerization of hydrophobic polymeric chains along the surface. The functionalized graphene oxide successfully achieved the desired hydrophobicity as it displayed the characteristic of being readily dissolved in organic solvent. Upon its addition into a polymeric solution and subjected to an electrospinning process,non-woven random nanofibers embedded with graphene oxide sheets were obtained. The prepared polymeric nanofibers were subjected to two-step thermal treatments that eventually converted the polymeric chains into a carbon-rich conductive structure. A unique morphology was observed upon the addition of the functionalized graphene oxide, whereby the sheets were embedded and intercalated within the carbon nanofibers and formed a continuous structure. This reinforcement effectively enhanced the electrochemical performance of the carbon nanofibers by recording a specific capacitance of up to 140.10 F/g at the current density of 1 A/g, which was approximately three folds more than that of pristine nanofibers.It also retained the capacitance up to 96.2% after 1000 vigorous charge/discharge cycles. This functionalization technique opens up a new pathway in tuning the solubility nature of graphene oxide towards the synthesis of a graphene oxide-reinforced polymeric structure.     

Highly sensitive composite electrode based on electrospun carbon nanofibers and ionic liquid

A novel composite electrode has been developed using electrospun carbon nanofibers (CNF) and the ionic liquid 1-butyl-4-methylpyridinium hexaflurophosphate (PFP). The highly pure CNF without any pretreatment exhibited very low background noise and high voltammetric responses. When applied to sensing of biomolecules under physiological conditions, the CNF/PFP electrode provided attractive electrochemical performances, such as high sensitivity and good selectivity for simultaneous detection of dopamine, ascorbic acid and uric acid, guanine and adenine, as well as high signal-to-noise ratio and good stability for amperometric detection of NADH.     

Enhancement of conductivity by diameter control of polyimide-based electrospun carbon nanofibers

Oxydianiline-pyromellitic dianhydride poly(amic acid) (ODA-PMDA PAA) was polymerized with a catalyst support of triethyl amine for controlling molecular weight. This polymer was used for electrospinning in the preparation of PAA nanofibers, a precursor of carbon nanofibers. Here the amount of catalyst and concentration of PAA solution were optimized to produce polyimide-based carbon nanofibers approximately 80 nm in diameter. The effects of molecular weight of PAA, bias voltage, and spinning rate on the morphology of electrospun PAA and polyimide nanofibers have been evaluated. We showed that the conductivity of the carbon nanofiber mat decreased with increasing nanofiber diameter, where the conductivity of polyimide-based carbon nanofiber mat was much higher than those of other types of carbon nanofiber mat. The key ingredient to increase conductivity in a carbon nanofiber mat was found to be the number of cross junctions between nanofibers.