o-Hydroxyacetophenone thiosemicarbazone as a reagent for the rapid spectrophotometric determination of palladium

o-Hydroxyacetophenone thiosemicarbazone has been synthesized and employed as a new reagent for the spectrophotometric determination of palladium(II), which forms two complex species with it in aqueous dimethylformamide at pH 6.0, these having 1:1 and 1:2 metal-ligand ratios. The Job and molar-ratio plots have an unusual shape that is due to the stepwise conversion of the 1:1 complex into the 1:2 species. The molar absorptivity at 370 nm is 9 x 10(3) l.mole(-1).cm(-1). Beer's law is obeyed over the range 0.42-10.6 mug/ml palladium.     

Simultaneous determination of manganese and zinc in mixtures using first- and second-derivative spectrophotometry

A new direct spectrophotometric determination of manganese with 5,8-dihydroxy-1,4-naphthoquinone (naphthazarin,NAZA) is reported. Absorption maximum, molar absorptivity and Sandell's sensitivity of 1:2 (M:L) complex are 695 nm, 1.88x10(4) l mol(-1) cm(-1) and 2.92 ng cm(-2), respectively. A linear calibration graph is obtained up to a concentration of 7.2 mug ml(-1) of manganese. The optimum range for determination (Ringbom) is between 0.20 and 6.8 mug ml(-1). A rapid method for simultaneous determination of manganese and zinc in their mixture using derivative spectra is described. The range 0.28-5.6 mug ml(-1) manganese could be determined in the presence of 0.33-6.8 mug ml(-1) zinc and vice versa. The developed method was applied to the simultaneous spectrophotometric determination of manganese and zinc in some synthetic mixtures and was found to give satisfactory results.     

Spectrophotometric determination of palladium after solid-liquid extraction with 1-(2-Pyridylazo)-2-naphthol at 90 degrees C

An effective spectrophotometric determination of palladium with 1-(2-pyridylazo)-2-naphthol (PAN) using molten naphthalene as a diluent has been studied. A green complex of palladium with PAN is formed at 90 degrees C. In the range of pH 1.5-7.5, the complex is quantitatively extracted into molten naphthalene. The organic phase is anhydrously dissolved in CHCl(3) to be determined spectrophotometrically at 678 nm against the reagent blank. Beer's law is obeyed over the concentration range of 0.5-10 ppm. The molar absorptivity and Sandell's sensitivity are 1.2 x 10(4) l mol(-1) cm(-1) and 0.0070 mg cm(-2), respectively. The optimum conditions for determination are obtained. The interferences of various ions are observed in detail. The method has been applied to the determination of palladium in synthetic samples.     

Extraction and spectrophotometric determination of Pd(II) with 3,4,4a,5-tetrahydro-3,3,4a-trimethyl-7-(substituted)-pyrimido(1,6-a)-benzimidazole-1-thiol (PBT)

A method for the extraction-spectrophotometric determination of palladium with 3,4,4a,5-tetrahydro-3,3,4a-trimethyl-7-(substituted)-pyrimido(1,6-a)benzimidazole-1-thiol (PBT) is described. PBT-Pd(II) complex is extracted from an acidic aqueous solution (0.01-0.5M HClO(4)) into a chloroform layer. The absorbance is measured at 438 nm and the molar absorptivity found to be 1.033 x 10(4)M(-1) cm(-1). The complex system conforms to Beer's law over the range 1.9-28.5 mug/ml palladium(II). The effects of pH (2-6), HClO(4) concentration, PBT concentration and shaking time were studied. The ratio of metal ion to ligand molecules in the coloured complex was found to be 1:4. The tolerance limit for many metals have been determined. Finally, the method has been applied successfully to the determination of palladium in synthetic mixtures and in the standard palladium carbon powder (palladium catalyst).     

A spectrophotometric study of the determination of gold with phenothiazine

The reaction of Au(III) with phenothiazine has been studied and a reaction mechanism proposed. Optimal conditions for the reaction have been found and a new spectrophotometric method has been developed for determination of Au(III). The method is advantageous in its simplicity and reproducibility. Gold can be determined in the concentration range 2-20 mug/ml.     

Flotation-spectrophotometric method for determining palladium by means of the ion-association complex of pentabromopalladate(II) with Rhodamine 6G

The conditions for the formation of a suitable coloured palladium ion-association complex with a basic dye have been examined, and a spectrophotometric method developed for the determination of palladium with bromide and Rhodamine 6G (R6G). Benzene is used for flotation and dimethylformamide for dissolution of the ion-association complex. The molar absorptivity is 3.0 x 10(5) l. mole(-1).cm(-1) at 53Onm. Beer's law is obeyed up to a palladium concentration of 0.3 mug/ml. The composition of the complex is [R6G(+)](3)[PdBr(3-)(5)]. Platinum interferes severely but other platinum metals interfere to a lesser degree. The method has been applied to the determination of traces of palladium in metallic platinum after a preliminary separation with nickel dimethylglyoximate as collector.     

Prediction of conditions for use of spectrophotometric reagents: p-dimethylaminobenzilidenerhodanine as a spectrophotometric reagent for silver and palladium

A method for theoretical estimation of the detection limits of spectrophotometric reagents is reported. The concentration limits of Beer's law when p-dimethylaminobenzilidenerhodanine is used for determination of silver and palladium are defined on the basis of the stability constants. Conditions for determination of 2-10mug, of Ag per 25ml and 1-5mug of Pd per 25ml with standard deviation 0.03mug per 25 ml are proposed.     

Spectrophotometric determination of palladium with 5,6-dimethyl-1,3-indanedione-2-oxime

A rapid, sensitive and selective method has been developed for the determination of palladium with 5,6-dimethyl-1,3-indanedione-2-oxime in acetate buffer (pH 5.5). Beer's law is obeyed over the range 0.15-4.17 mug/ml palladium(II). The molar absorptivity at 370 nm is 2.98 x 10(4) 1.mole(-1).cm(-1). The method has been applied for the determination of palladium in synthetic mixtures corresponding to PtIr and Oakay alloys. An interesting feature of the system is the abnormal shape of the Job and molar-ratio plots obtained.     

Spectrophotometric determination of cyanide with organic disulphides

The reaction of cyanide ion with the disulphides 2,2'-dithiodipyridine, 4,4'-dithiodipyridine, 2,2'-dithiodipyrimidine, and 5,5'-dithiobis(2-nitrobenzoic acid) to displace an absorbing thiol anion has been evaluated for the spectrophotometric determination of cyanide. Reaction is somewhat slow and is applicable to cyanide determination in the range 0.2-5.0 mug ml . By variation of reactant ratios and pH the concentration range can be increased to 50 mug ml . The reaction is faster when cyanide is present at a higher concentration than the disulphide.     

Spectrophotometric flow injection determination of formetanate and m-aminophenol in water after reaction with p-aminophenol

An automated procedure has been developed for the determination of formetanate and its metabolite m-aminophenol (MAP) in water samples. MAP can be selectively determined in the presence of formetanate by direct on-line reaction with p-aminophenol and spectrophotometric measurement of the absorbance at 576 nm in the presence of KIO(4), as oxidizing agent. The method has a limit of detection of 5 x 10(-7)M, it provides a recovery percentage from 95 to 104% and permits one to carry out 120 measurements/hr. The spectrophotometric determination of formetanate must be carried out after a previous hydrolysis to MAP. To determine formetanate in the presence of MAP, two steps are necessary. Firstly, the MAP content is selectively determined as has been mentioned above. After that, the sample is treated with 0.05M NaOH at 90' degrees C, to hydrolyze the formetanate to MAP, and then the sum of both is determined spectrophotometrically. The difference between the results obtained in each step gives the formetanate concentration. The developed procedure for the determination of formetanate provides a sensitivity of 1070 absorbance units mol(-1) l and a limit of detection of 1.9 x 10(-7)M, which corresponds to 50 mug/l of formetanate hydrochloride. The method has been applied to the analysis of natural water samples fortified with formetanate and MAP, and formetanate has also been quantitatively recovered in irrigation waters at a concentration level of 1.9 x 10(-6)M which corresponds to 500 mug/l. On the other hand, working in the stopped-flow mode, for a reaction time of 100 sec, the sensitivity of the formetanate determination can be increased to 4642 absorbance units mol(-1) l but the limit of detection remains of the order of 44 mug/l.     

Simultaneous determination of hexavalent and total chromium in water and plating baths by spectrophotometry

A new spectrophotometric determination method of hexavalent chromium in waste water and plating baths is described based on the oxidation of beryllon III by chromium(VI) in 0.02M sulphuric acid medium. The decrease in the absorbance of beryllon III was measured at 482 nm with an apparent molar absorptivity of 5.15 x 10(4)1.mole(-1).cm(-1). Beer's law was obeyed for chromium(VI) over the range 0-25 mug/25 ml. After the oxidation of Cr(III) to Cr(VI) by ammonium persulphate, total chromium can be determined. Therefore, chromium(III) can be calculated by subtracting chromium(VI) from total chromium. The detection limit is 0.015 and 0.020 mug/25 ml for chromium(VI) and total chromium, respectively. A sensitive spectrophotometric method for trace Cr(III) and Cr(VI) in waste water and plating baths was developed with good precision and accuracy. The reaction is also discussed.     

Spectrophotometric determination of zinc with hydrazidazol in the presence of Triton X-100 and its application in metal analysis

A new spectrophotometric method for the determination of zinc is proposed. The chromogenic agent Hydrazidazol forms a 1:1 chelate with zinc in the presence of Triton X-100 in a medium containing 20-40% ethanol. The molar absorptivity and conditional formation constant have been found to be 2.7 x 1O(4) l.mole(-1).cm(-1) (at 640 nm) and 10(5.32) respectively. Beer's law is obeyed for zinc over the range of 0.2-0.8 mug/ml with a standard deviation of 0.024 mug/ml. The method can be applied to the determination of zinc in cadmium metal and its oxide after preconcentration by selective extraction of zinc thiocyanate into ethyl acetate in the presence of EDTA and thiosulphate as masking agents.     

Katalytische bestimmung von silberspuren in wabetariger lösung und nach extraktion

The application of the catalysed oxidation of Bromopyrogallol Red by potassium per- sulphate for silver determination is discussed. In aqueous solution silver concentrations of 0.5- 1 mug/ml can be determined and 1- 13 ng/ml in the presence of 1, 10-phenanthroline as activator. In combination with solvent extraction, catalytic determination of the extracted silver is possible even in presence of 200 mug of iron(III), cobalt(II) and palladium(II). By means of an automatic variant of the simultaneous comparison method a more sensitive determination (0.2-20 ng/ml) was achieved.     

A sensitive spectrophotometric method for the determination of methyl alcohol in air and water

A sensitive spectrophotometric method for the indirect determination of methyl alcohol in air and water is described. The methyl alcohol is oxidized to formaldehyde which is then determined in acidic medium with p-aminoazobenzene and sulphur dioxide. Beer's law is obeyed in the range 100-600 mug of methyl alcohol in 25 ml of final solution and the wavelength of maximum absorption is 505 nm. The lower limit of determination is 5 mug ml in the sample. Several common organic co-pollutants do not interfere. The method can be used for determination of methyl alcohol in blood.     

Spectrophotometric determination of molybdenum based on charge transfer complex in PVA medium

A very simple, selective and sensitive method was developed for the spectrophotometric determination of Mo in the presence of W. The method was based on the formation of color charge transfer complex, molybdotungstophosphate-3,3',5,5'-tetramethylbezidine anion, which was solubilized and stabilized in PVA medium. Following the recommended procedure, molybdenum could be determined in the linear range of 0.04-2.5 mug ml(-1) and the molar absorptivity was 1.47x10(4) l mol(-1) cm(-1) at 660 nm. The proposed method had been applied to the determination of trace molybdenum in tungsten ore with satisfactory results.     

Spectrophotometric determination of beryllium with calcichrome

A method is established for the spectrophotometric determination of small amounts of beryllium as a 1:1 complex with Calcichrome in slightly acidic solution. Beer's law is obeyed over the range 0.05-0.6 ppm Be in the final solution and the apparent molar absorptivity is 9.7 x 10(3) l.mole(-1). cm(-1) at 625 nm. Up to about 15 mug of beryllium in the final solution can be sensitively and selectively determined with a relative error of less than 2% in the presence of EDTA as masking agent.     

A simple simultaneous flow injection method based on phosphomolybdenum chemistry for nitrate and nitrite determinations in water and fish samples

A direct spectrophotometric flow injection method for the simultaneous determination of nitrite and nitrate has been developed. The method is based on the oxidation of a phosphomolybdenum blue complex by the addition of nitrite and the decrease in absorbance of the blue complex is monitored at 820 nm. The injected sample is split into two segments. One of the streams was directly reacted with the above reagent and detected as nitrite. The other stream was passed through a copperised cadmium reductor column where reduction of nitrate to nitrite occurs, and the sample was then mixed with the reagent and passed through the cell of the spectrophotometer to be detected as nitrite plus nitrate. The conditions for the flow injection manifold parameters were optimised by experimental design and the concentration of nitrite and nitrate was determined in the linear range from 0.05 to 1.15 mug ml(-1) nitrite and 0.06 to 1.6 mug ml(-1) nitrate with a detection limit of 0.01 mug ml(-1) for nitrite and 0.025 mug ml(-1) for nitrate. The method is suitable for the simultaneous determination of nitrite and nitrate in fish and water samples with a sampling rate of 25+/-2 sample per hour.     

Extraction and spectrophotometric determination of titanium(IV) with malachite green and p-chloromandelic acid, with application to mild steels

A very sensitive, selective and simple method for extraction and spectrophotometric determination of titanium(IV) with an alpha-hydroxy acid has been developed. p-Chloromandelic acid reacts with titanium in weakly acidic aqueous solution at room temperature to form a complex anion extractable into chlorobenzene with Malachite Green as counter-ion. Titanium is determined indirectly by measuring the absorbance of Malachite Green in the extract at 630 nm. The calibration graph is linear for titanium(IV) over the range 0.25-7.5muM (0.05-1.44 mug); the apparent molar absorptivity is 1.31 x 10(5) l.mole(-1).cm(-1). The method has been successfully applied to the determination of titanium in mild steels.     

Gravimetric and spectrophotometric determination of palladium with 2-hydroxy-5-methylpropiophenone oxime

2-hydroxy-5-methylpropiophenone oxime (HMP) reacts with palladium in strongly acidic media to form a yellow water-insoluble complex. Palladium has been determined gravimetrically and interference by certain ions studied. The yellow complex is extractable into carbon tetrachloride in the pH range 1-4. The absorption maximum of the complex lies at 375 mmu, and Beer's law is obeyed in the range 0-15 ppm of palladium. The sensitivity is 0.22 mug Pd/cm(2) for log I(0)/I = 0.001. The effect of a number of foreign ions has been studied and several can be tolerated to an appreciable extent. The ratio of metal: ligand in the complex is 1:2.     

A highly sensitive spectrophotometric method for determination of micro amounts of arsenic

A highly sensitive spectrophotometric method for determination of arsenic, based on the formation of an ion-association complex between arsenoantimonomolybdenum blue and Malachite Green, has been developed. The ion-association complex is soluble in the presence of Triton X-305, so arsenic can be determined directly in aqueous solution. The apparent molar absorptivity for arsenic is 1.13 x 10(5) l.mole(-1).cm(-1) at 640 nm. Beer's law is obeyed for 0-5 mug of arsenic. The lower limit of determination (absorbance = 0.01) is 4 ng ml in the final solution.