Flow-injection spectrophotometric determination of chloramben

Abstract

A method for the dechlorination of PCB mixtures (Aroclor formulations) to biphenyl was extended to soils. The contaminated sample was mixed with magnesium flakes, potassium hexachloropalladiate (K₂PdCl₆), propan-2-ol and water then permitted to react for up to six hours. Biphenyl, recovered by extraction into hexane, was quantified by gas chromatography with flame ionization detection. The reaction was very efficient in propan-2-ol / water (～95%), surfactant emulsion or sand mixture and virtually complete in soil provided that excess magnesium (2 g) and the K₂PdCl₆ were added to the sample prior to the addition of water. Higher PCB loadings were readily determined in field contaminated soils either by direct determination within the matrix or by standard additions. However, analyte concentrations were appreciably over-estimated in Soxhlet or sonication extracts of a certified reference material that contained sub-ppm levels of analyte. The over-estimation is considered to result from the conversion in part of natural organic matter to biphenyl.     

Flow-injection spectrophotometric determination of ascorbic acid in pharmaceutical products with the Prussian Blue reaction

A lot of modern analytical strategies for exploiting chemistries have been developed by using flow-injection analysis. However, even after 20 years of flow-injection evolution, there still are new quantitative procedures being established using old qualitative assays. The formation of Prussian Blue is a classical test to detect Fe(2+) using hexacyanoferrate(III) as a precipitating reagent. This reaction was evaluated for spectrophotometric determination of ascorbic acid employing Fe(3+) and hexacyanoferrate(III) as chromogenic reagents. An excess of the complexing anion avoids the formation of precipitate and forms a deep blue solution when Fe(3+) is reduced to Fe(2+) by ascorbic acid. The maximum absorbance of the colored complex occurs at 700 nm and the molar absorptivity is 3.0 x 10(4) 1 mol(-1) cm(-1). Under flow-injection conditions the Prussian Blue reaction was employed with an intermittent flow of an oxalate alkaline solution for removing the colored product adsorbed on tube and flow-cell walls. Reference solutions containing 5.0 x 10(-6)-1.0 x 10(-4) M of ascorbic acid were employed to obtain the analytical curve (r = 0.9999). For all solutions the relative standard deviation was lower than 1.0% (n=10). Results obtained for ascorbic acid determination in pharmaceutical products (Cewin, Redoxon and Cebion) are in good agreement with those obtained by using a flow-injection procedure involving the reaction between triiodide and ascorbic acid. The sampling frequency is 140 h(-1) and only 430 microl of reagents is consumed in each determination.     

Flow-injection spectrophotometric determination of salbutamol with 4-aminoantipyrine

A flow-injection method is proposed for the determination of salbutamol. The method involves the condensation of salbutamol with 4-aminoantipyrine in the presence of hexacyanoferrate (III) in alkaline medium, producing a coloured quinoneimide that was detected absorptiometrically at 500 nm.

The values of four variables (two reactor lengths and two reagent concentrations) were optimised by means of the sequential simplex method and their influence studied in univariant way.

The method was validated and compared with the HPLC method established in the United States Pharmacopeia (USP). Linearity was demonstrated in the range 0–74.1 mg/L of salbutamol sulfate (r² = 0.9999). Commercial samples of pharmaceuticals containing salbutamol sulfate (tablets and oral solutions) were analysed and the results obtained with the proposed method agreed with the USP method in less than 1.6%, with precision similar to the HPLC method (1%–2% R.S.D.). The sampling frequency was 75 samples/hour.     

Flow-injection spectrophotometric determination of acetyl-coenzyme A with immobilized phosphotransacetylase

Phosphotransacetylase (PTA) is immobilized on AF-Tresyl TOYOPEARL 650 gel and used on-line in a stainless-steel column (10 × 4 mm i.d.). CoA-SH liberated enzymatically from acetyl-CoA is reacted with Ellman's reagent [5,5′-dithiobis(2-nitrobenzoic acid)] in the carrier stream. The calibration graph for acetyl-CoA is linear from 4 × 10^?6 to 4 × 10^?4 M and the detection limits is 8 × 10^?7 M. The immobilized enzyme can be employed for over 4 months without any significant decrease in activity. The enzyme retains its activity in methanol even though the initial rate of reaction is decreased.     

Flow-injection amplification for the spectrophotometric determination of iodide

A flow manifold is described in which iodide (0.05–15 μg ml^?1) in a 50-μl sample is oxidized by bromine water to iodate, most of the excess of bromine is reduced by formic acid, and the iodate is reacted with more iodide to form triiodide, which is determined spectrophotometrically. Six-fold amplification is achieved. The relative standard deviation is ca. 1%).     

Flow-injection spectrophotometric determination of trace vanadium based on catalysis of the gallic acid bromate reaction

High sensitivity is obtained by using high concentrations of gallic acid and bromate, although the uncatalyzed reaction is significant. Various reactant concentrations, reaction temperature, pH and residence times can be used to alter the linear calibration ranges and sensitivity for vanadium. With reagent streams of 1.76 M bromate and 0.06 M gallic acid at pH 3.8 (each at 1 ml min^?1), 0.2–20 ng of vanadium (20-μl injections) can be determined at 30°C. Oxidized gallic acid is detected at 380 nm. When the bromate concentration is decreased to 0.5 M and the temperature is 65°C, 0.05–4 ng of vanadium can be determined; the relative standard deviation is ca. 5% for 0.6 ng of vanadium. The toleranes for Al(III), Fe(III), Mo(VI) and iodide are 10 ng, 10 ng, 50 ng and 200 ng, respectively, for the determination of 1 ng of vanadium. About 12 samples can be injected per hour.     

Flow-injection spectrophotometric determination of enalapril in pharmaceuticals with bromothymol blue

Enalapril (1.5–60 μ gl^?1) in aqueous solution is extracted into dichloromethane as its ion-pair with bromothymol blue in an unsegmented flow system and quantified spectrophotometrically. Up to 80 samples h^?1 can be processed, with r.s.d. of 1.0–3.4%. The degradation products of enalapril and excipients in the pharmaceutical dosage form do not interfere.     

Flow-injection spectrophotometric determination of aluminium in water with pyrocatechol violet

Optimum conditions for the adaptation of the spectrophotometric pyrocatechol violet method for aluminium to a flow-injection system are described. The detection limit is 3 μg Al l^?1 and calibration graphs are linear up to 3 or 10 mg l^?1 (with 200-μl or 10-μl injection loops, respectively). The relative standard deviation is 〈 2% at 0.1 mg Al l^?1. Potential interferences of 40 common inorganic ions and of 20 organic substances, including fulvic acid, are reported. With the use of conventional masking agents and predigestion of samples with high organic content, the method is suitable for determining total aluminium in natural waters.     

Flow-injection spectrophotometric determination of periodate and iodate by their reaction with pyrogallol red in acidic media

A simple and efficient flow-injection method was used with good results to determine periodate and iodate in water. The method is based on the reaction of periodate or iodate with pyrogallol red in sulfuric acid media. The reaction was monitored spectrophotometrically by measuring the decrease in absorbance of pyrogallol red at 470 nm. The chemical and FIA variables were established using the univariate and simplex optimization methods. The calibration curve was linear over the concentration ranges of 0.8-73.0 and 2.0-100.0 microM for IO4- and IO3-, respectively. The detection limits were 0.7 and 1.0 microM for IO4- and IO3-, respectively. The sample throughput was 20 +/- 5 h(-1). The influence of potential interfering ions in the determination of the anions was tested. The relative standard deviations for 4.20 and 5.73 microM periodate and iodate were 1.8 and 2.2%, respectively.     

Flow-injection spectrophotometric determination of methyldopa in pharmaceutical formulations

A flow-injection spectrophotometric procedure is proposed for methyldopa determination in pharmaceutical preparations. The determination is based on formation of a yellow product (measured at 410 nm) after complexation of methyldopa with molybdate. Under optimal conditions, Beer's law is obeyed in a concentration range of 50-200 mg l⁻¹ methyldopa. Typical correlation between absorbance and analyte concentration was 0.9999. Usual excipients used as additives in pharmaceuticals do not interfere with the proposed method. The analytical frequency was 210 h⁻¹ and the relative standard deviation (R.S.D.) was ≤2% for sample solution containing 150 mg l⁻¹ methyldopa (n = 11). The analytical results obtained in commercial formulations by applying the proposed FIA method were in good agreement with labeled values and those obtained by the Brazilian Pharmacopoeia procedure at 95% confidence level.     

Flow-injection stopped-flow kinetic spectrophotometric determination of drugs, based on micellar-catalysed reaction with 1-fluoro-2,4-dinitrobenzene

A flow-injection stopped-flow kinetic spectrophotometric method for the determination of hydrazines, hydrazides, amines and amino-acids, based on the cetyltrimethylammonium bromide catalysed reaction with 1-fluoro-2,4-dinitrobenzene is described. With the proposed method dihydralazine, isoniazid, levodopa and aspartame can be determined at concentrations of 0.1-6 x 10(-4)M. The calibration ranges can be varied by adjusting the pH and surfactant concentration. The determination of amphetamine, cysteine, s-carboxymethylcysteine, cephalexin, tobramycin and gentamicin is also feasible. The method has been applied to the determination of levodopa, isoniazid and aspartame in commercial pharmaceutical formulations. The determination of isoniazid in formulations containing the highly coloured antibiotic rifamycin, and of aspartame in coloured beverages was also accomplished. The results were in good agreement with those obtained by reference methods and the throughput was 40 measurements per hour with 0.4-3.9% RSD.     

Flow-injection determination of proteins based on the lowry spectrophotometric method

The flow-injection system is based on the use of Folin-Ciocalteus reagent, with 1,4-dithio-D,L-threitol to accelerate the formation of the coloured complex. The calibration graph for bovine serum albumin is linear between 0.01 and 0.1 mg ml^?1; the detection limit is 0.005 mg ml^?1 albumin and up to 0.5 mg ml^?1 can be determined. The injection frequency is 20 h^?1. The results obtained by the flow-injection method and by the manual Lowry procedure show excellent correlation. Egg lysozyme, alkaline phosphatase and β-lactoglobulin are also tested.     

Flow-injection spectrophotometric determination of residual free chlorine and chloramine

2,4-Dinitrophenylhydrazine has been suggested as a new reagent for the flow-injection spectrophotometric determination of residual chlorine based on its oxidation to 2,4-dinitrophenyldiazonium ion. The measurement of the decrease in colour intensity under reversed flow-injection (reagent injection) conditions has been used for the determination of 0.1–10 mg/l Cl present as free or combined chlorine, and for its speciation. The limit of detection was 0.05 mg/l Cl. Copper (II), iron (III) and many other ions have been found not to vitiate the results.     

Flow-injection ultraviolet spectrophotometric determination of sulphate in natural waters

The proposed method is based on measurement of the absorbance of the FeSO₄⁺ complex cation at 355 nm. Sample-injection and reagent-injection procedures are described. Calibration graphs are linear in the ranges 25–600 and 10–150 mg l^?1 sulphate, respectively. The main interference is from ultraviolet-absorbing organic compounds in the waters. Methods of eliminating the interference are discussed. Results for sulphate in river waters compare satisfactorily with those obtained by the gravimetric method. Depending on the pretreatment used, 10–30 samples can be analyzed per hour.     

Flow-injection extraction spectrophotometric determination of dichromate with the tetramethylenebis(triphenylphosphonium)cation

Chromium(VI) (0–5 μg) can be determined spectrophotometrically at 365 nm after flow-injection extraction into chloroform of the ion-associate, tetramethylenebis(triphenylphosphonium) dichromate. The carrier stream is distilled water and the reagent stream contains 1 M sulphuric acid and 0.5% (w/v) tetramethylenebis(triphenylphosphonium) bromide. The sampling rate is 24 h^?1. The calibration graph is linear up to 20 μg ml^?1 and the detection limit is 0.44 μg ml?1 chromium, based on injection volumes of 250 μl. The system has been applied to the determination of chromium in a range of steels.     

Flow-injection catalytic spectrophotometric determination of nitrite using the redox reaction between naphthol green B and potassium bromate

A flow injection catalytic spectrophotometric method is proposed for the determination of nitrite based on its catalytic effect on the redox reaction between naphthol green B and potassium bromate in phosphoric acid medium. The reaction is monitored spectrophotometrically by measuring the decrease in absorbance of naphthol green B at the maximum absorption wavelength of 722 nm. The detection limit is 0.5 ng cm(-3) in a sample volume of 90 mm(3). Up to 50 samples can be analyzed per hour with a relative precision of ca. 2%. The method is free from most interferences, especially from large amounts of nitrate. The procedure was successfully applied to the determination of trace nitrite in natural waters.     

Flow-injection determination of glutathione with amperometric monitoring of the enzymatic reaction

Glutathione sulfhydryl oxidase is immobilized on oxirane-acrylic beads (Eupegit-C) and packed in a small column. The simple system for glutathione comprises the immobilized enzyme column and a flow-through membrane-covered platinum/silver/silver chloride electrode pair for detection of hydrogen peroxide. The calibration graph for glutathione was linear from 0.05 to 1.0 mM for 200-μl samples. The assay took 3 min. The relative standard deviation for 0.5 mM glutathione was 2% (n=10).     

Flow-injection spectrophotometric determination of silicate,phosphate and arsenate with on-line column separation

The simultaneous determination of silicate, phosphate and arsenate by using flow-injection analysis with on-line column separation is described. Determinations are based on measurement of the absorbance at 810 nm of the heteropoly blue formed with ascorbic acid as reducing reagent. Effects of flow rates, temperature of reaction coils and sample injection volumes are reported; optimum conditions are 0.25 ml min^?1 for the ascorbic acid stream, 95°C for the reaction coils and 300 μl for the injection volume. With the anion-exchange column (TSK-gel SAX), the optimal flow rate of the eluent is 0.75 ml min^?1. Relative retention times depend on the concentration of the KCl/NH₃/EDTA eluting solution; separation and simultaneous determination of the three ions are satisfactory at around 10^?4 mol l^?1 concentrations of the three ions.     

Flow-injection spectrophotometric determination of ascorbic acid by reduction of vanadotungstophosphoric acid

Ascorbic acid may be determined spectrophotometrically at 360 nm based on reduction of vanadotungstophosphoric acid using flow-injection analysis. The carrier stream was distilled water and the reagent streams were buffer solution (pH 3.0), 1.735 × 10^?3 M dodecatungstophosphoric acid and 1.735 × 10^?3 M sodium vanadate. The injection rate was 80 h^?1. The calibration graph was linear up to 80 μg ml^?1 ascorbic acid and the relative standard deviation for the determination of 20 μg ml^?1 ascorbic acid was 1.5% (n=10). The detection limit was 1.0 μg ml^?1 ascorbic acid, based on an injection volume of 250 μl. The system was applied to the determination of ascorbic acid in vitamin C tablets.     

Flow-injection determination of nitrites based on their reaction with thiocyanates

A technique for the flow-injection determination of nitrites with spectrophotometric signal detection was developed and studied. Additionally, a combination of the developed technique with the on-line pre-concentration of low concentrations of nitrites in surface and potable waters was investigated. The technique is based on the reaction of nitrites with thiocyanates. The product of the analytical reaction (nitroso-S-thiocyanate) and its adducts with strong acids are stable in aqueous solutions, which is supported by quantum chemical calculations. It is shown that the reaction chosen is attractive for analytical applications, because it is highly selective. A decrease in the detection limit down to 1.5 ng/mL (3s) is achieved by combining FIA with on-line ion-exchange preconcentration. The technique developed is used for monitoring nitrites in natural and waste water. The throughput capacity is 300 samples per hour.Translated from Zhurnal Analiticheskoi Khimii, Vol. 60, No. 3, 2005, pp. 323–330.Original Russian Text Copyright © 2005 by Kuznetsov, Zemyatova, Ermolenko.