Rapid mass-spectrometric determination of boron isotopic distribution in boron carbide

Boron isotopic ratios are measured in boron carbide by thermionic ionization mass spectrometry with no prior chemical separation. A powder blend of boron carbide and sodium hydroxide is prepared, a small portion is transferred to a tantalum filament, the filament is heated to produce sodium borate, and the filament is transferred to the mass spectrometer where the(11)B/(10)B ratio is measured, using the Na(2)BO(2)(+) ion. Variables investigated for their effect on preferential volatilization of (10)B include the sodium hydroxide-boron carbide ratio and the temperature and duration of filament heating. A series of boron carbide pellets containing natural boron, of the type proposed for the control rods of the Fast Flux Test Facility reactor, were analysed with an apparently unbiased result of 4.0560 for the (11)B/(10)B ratio (standard deviation 0.0087). The pellets contained over 3% metal impurities typically found in this material. Time of analysis is 45 min per sample, with one analyst.     

Determination of isotopic ratio of boron in boric acid using laser mass spectrometry.

A reflectron time-of-flight mass spectrometer (RTOFMS) with a laser ablation ion source was used to determine the isotopic ratio of 10B/11B present in boric acid solutions, using graphite as the matrix. The atom % 10B values obtained were within +/-1% of the actual ones. The determination of the boron isotopic ratio using this method is, in comparison to other methods, faster, less expensive and easier to perform. The results are compared with the values determined using thermal ionization mass spectrometry.     

Complexes of morin and quercetin with boric acid and oxalic acid in acetic acid medium. Fluorimetric determination of boron

The binary and ternary fluorescent complexes of morin or quercetin with boric acid and oxalic acid in an anhydrous acetic acid medium are described. The physico-chemical and spectral properties and chemical composition of these complexes have been established. The ternary complexes are suitable for fluorimetric determinations of boron. The limits of detection are 0.1 ng B ml^-1 and 0.3 ng B ml^-1, for the morin and quercetin complexes, respectively, and calibration graphs are linear up to 10 μg B ml^-1.     

Determination of boron as boric acid in eye lotions using a sequential injection system

A simple and reliable sequential injection analysis (SIA) system is described for the determination of boron as boric acid in eye lotions. This method is based on the complexation reaction between d-sorbitol and boric acid followed by the acid-base reaction with methyl orange (MO). The colour change reaction is monitored at 520 nm. The system is able to monitor boron at a frequency of 30 samples per h with a relative standard deviation of less than 0.6%. The calibration graph is linear up to 12-mg l(-1). The system has a detection limit of 0.06-mg l(-1). No significant differences (at 95% probability level) were found between the proposed SIA method and the reference method.     

N,N-Dimethyl formamide facilitated formation of hexagonal boron nitride from boric acid

In this paper, we report on a promoting novel process for the formation of h-BN plates by using N,N-dimethyl formamide-treated boric acid (DMF-BA). Using this B source, the formation of h-BN can be indeed improved greatly compared to using pure boric acid (BA). This method effectively reduces the content of boric acid and amorphous boric oxide, enhancing the transformation rate of h-BN. For preparation of pure h-BN, it can obviously lower the resultant temperature without further purification process. Via graphitization index (G.I.) calculation and thermostability analysis, the pure h-BN plates obtained from the DMF-BA would be a promising candidate for raw material of c-BN and low-temperature applications in the air.     

Application of PIGE method for quantification of total boron in neutron absorbers and shielding materials and isotopic composition in in-house prepared enriched boron carbide samples

Journal of Radioanalytical and Nuclear Chemistry - The in situ current normalized particle induced gamma-ray emission method using 4 MeV proton beam was utilized for total boron...     

Column chromatographic boron isotope separation at 5 and 17 MPa with diluted boric acid solution

Boron isotopic fractionation factor (S) between boron taken up in strongly basic anion exchange resin and boron in aqueous solution was determined by breakthrough column chromatography at 5 and 17 MPa at 25 degrees C, using 0.1 mM boric acid solution as feed solution. The S values obtained were 1.018 and 1.012, respectively, which were smaller than the value reported by using the same chromatographic method at the atmospheric pressure at 25 degrees C with the boron concentration of 10mM, but were larger than the values under the same condition with much higher concentration of 100 and 501 mM. Calculations based on the theory of isotope distribution between two phases estimated that 21% (5 MPa) and 47% (17 MPa) of boron taken up in the resin phase was in the three-coordinated B(OH)(3)-form, instead of in the four-coordinated B(OH)(4)-form, at high pressures even with a very diluted boric acid solution. We discussed the present results by introducing (1) hydration and (2) a partial molar volume difference between isotopic molecules. Borate may have been partially dehydrated upon transfer from the solution phase to the resin phase at high pressures, which resulted in smaller S values compared with those at the atmospheric pressure. Instead, it may be possible that the difference in the isotopic partial molar volume difference between B(OH)(3) and B(OH)(4)(-) caused the S value to decrease with increasing pressure.     

Fast isotopic separation of 10B and 11B boric acid by capillary zone electrophoresis

Fast isotopic separation of ¹⁰B and ¹¹B boric acid by CZE was demonstrated. The BGE contained 25 mM phenylalanine and 5 mM putrescine (рН 8.95). The running conditions were +25 kV at 20°C with indirect photometric detection at 210 nm. Baseline separation was achieved in less than 9 min. RSD of migration times and corrected peak areas were less than 0.5 and 3%, respectively (n = 5). Linearity was demonstrated in the range 0.2–2 mM for ¹¹B and 0.2–0.5 mM for ¹⁰B.     

Avidin self-associates with boric acid gel suspensions: an affinity boron carrier that might be developed for boron neutron-capture therapy

It has been shown in preliminary studies that the antibacterial protein avidin self-associates with the boric acid gel polymer, and avidin-coated gel particles in the micrometer and submicrometer size ranges are of interest for boron neutron-capture therapy (BNCT), which is neutron-induced fission of boron-10 to produce intense alpha radiation for tumor destruction. The gel particles carry large amounts of boron-10 and are theoretically able effect a meaningful tissue dosing through BNCT. A gross precipitation of gel particles occurs within 46 min of mixing when the avidin/colloid ratio is about 0.34 g avidin/g colloid. This is a minimum time if gel and avidin concentrations are in the low microgram/milliliter range, but at higher proportions of avidin the time delay to precipitation increases significantly; i.e., the colloid surface becomes blocked, inhibiting lattice formation. The avidin-coated gel particles eventually cross-link, forming a solid matrix and precipitating on a timescale measured on the order of an hour. At shorter exposure times rapid agglutination-like reactions were observed with biotinylated bovine albumin, suggesting that two-stage pretargeting of specific tissues should be possible with biotinylated antitumor antibodies. However, for BNCT to be practical, avidin's interaction with the gel needs to be strengthened, and all aryl-B(OH)(2) groups on the particle surfaces must be blocked, or else the particles will interact strongly and nonspecifically with each other and with the carbohydrate groups present on most cell surfaces. Glyceric acid delays the precipitation of the particle suspensions while most simple and complex carbohydrates accelerate it.     

Kinetic analysis of formation of boron trioxide from thermal decomposition of boric acid under non-isothermal conditions

Journal of Thermal Analysis and Calorimetry - This study investigated the kinetic analysis of the dehydration process of boric acid (H3BO3) and its transformation into boron trioxide (B2O3) under...     

Improving effect of boron carbide on the combustion and thermal oxidation characteristics of amorphous boron

Boron carbide (B₄C) is one of the main products from the primary combustion of boron (B)-based propellants and has a significant influence on the secondary combustion of B. To systematically evaluate its effects on the secondary combustion of B, mixtures of B₄C and B in different mass ratios were prepared. To study the ignition temperatures and combustion flames of the samples, a xenon lamp ignition experimental system and a flame shape test system were designed, respectively. A thermogravimetry–differential scanning calorimetry–Fourier transform infrared spectroscopy combined thermal analysis system was used to study the thermal oxidation characteristics and analyze the gaseous products of the samples. The results indicate that B₄C reduces the heat absorption at the beginning of the ignition, but subsequently prevents the rapid rise of sample temperature. During the stable combustion stage, the maximum flame length under optical density 10⁻⁴ (OD4) filter was 20.4 mm, and the maximum flame length under 580 nm + OD4 filters (represents the combustion of B element) was 16.7 mm. The samples contained a small amount of HBO₂ and H₃BO₃, which led to slight mass loss during the low temperature section of the thermal oxidation process. During the high temperature section, the oxidation of B and B₄C caused considerable mass gain. The gaseous products of the thermal oxidation process include CO₂, CO, and H₂O. In general, the B content of 60% was the most beneficial to decrease the oxidation temperature, increase the combustion intensity, and improve the heat-releasing ability of the samples.

     

Voltammetry and controlled-potential coulometry with boron carbide electrodes

With the boron carbide electrode, E_{p$\text{p}\text{2}$} values were determined for the reduction of the following ions: Cd(II), Co(II), Cu(II), Fe(III), Ni(II), Pb(II), Ru(IV), Sb(V), and U(VI). The linear dependence of peak current on concentration is demonstrated for the U(VI) → U(IV) and Fe(III) → Fe(II) reductions at the boron carbide electrode. The suitability of the electrode for the controlled-potential coulometric ti trations of Fe(II) → Fe(III), Fe(III) → Fe(II), and U(VI) → U(IV) was studied; the results were inconclusive because of the small surface area that could be used conveniently and the possibility of oxygen leaks in the cell.     

Developments in accurate and traceable chemical measurements

In recent years there has been considerable interest in the application of the principles of measurement science to chemistry. This has led to the recognition of 'metrology in chemistry' as an area of relevance to analytical chemistry research. This tutorial review describes the benefits to chemistry of the implementation of the principles of measurement science and explains how they are able to improve the reliability and accuracy of chemical measurements.     

Solvation of sulphonic acid groups in Nafion® membranes from accurate conductivity measurements

The wide degree of scatter of experimental data shows unambiguously that Nafion^®117 conductivity is very sensitive to climatic conditions, temperature and relative humidity. In order to allow equilibrium with the surrounding atmosphere to be reached rapidly, a conductivity cell, adapted to a small size membrane samples, has been designed. Conductivity measurements have been carried out by electrochemical impedance spectroscopy (EIS) between 10 °C and 95 °C in a broad domain of relative humidity, i.e., 10–98%. The measurement set up provides reproducible data with a total uncertainty of 30% in a large range of conductivity values. These accurate data enable a power relationship to be proposed at constant temperature between conductivity and relative humidity. This suggests that the solvation process of a sulphonic acid group involves four water molecules. Based on the assumption that a proton mobility depends weakly on temperature, a solvation enthalpy of a sulphonic acid group by water of −135 kJ mol⁻¹ is deduced from conductivity variations with the temperature.     

Influence of boric acid on electrospray ionization efficiency

Liquid chromatography electrospray ionization mass-spectrometry (LC-ESI-MS) was used to analyze 9-fluorenylmethylmethoxycarbonyl chloride (Fmoc-Cl) and diethyl ethoxymethylenemalonate (Deemm) derivatives of three amino acids and five other compounds. Influence of boric acid on their ionization was investigated and dramatic impact on the signal was observed. The strongest signal suppression (6% of signal remains) was observed for the Deemm derivative of beta-Alanine (with ammonium acetate in eluent). With only formic acid as the eluent pH modifier, signal enhancement was observed, being largest for Fmoc-Cl derivative of Phenylalanine, 267%. Investigation of the influence of boric acid shows that it is a possible signal enhancer for LC-ESI-MS analysis.