Spectrophotometric extractive titrations-III Simultaneous determination of silver and copper in high purity lead

A procedure for the simultaneous determination of silver and copper in high-purity lead is given. After dissolution of the sample the majority of the lead is removed by precipitation with ammonium sulphate. Silver and copper are then determined by spectrophotometric extractive titration at pH 4.3-5.5 with dithizone. Changes of absorbance are measured at 550 mmu. The procedure has been checked by the method of standard additions and by comparison with conventional methods. The procedure is highly selective. The limit of determination is 2.5 x 10(-5)% of silver and 1.1 x 10(-5)% of copper.     

Estimation of individual thio-salts and sulphate in flotation mill solutions

This paper presents methods found to be suitable for the determination of thio-salts and sulphate in flotation mill solutions. Thiosulphate, tetrathionate and trithionate are estimated spectrophotometrically after cyanolysis. A modified iodimetric procedure is used for sulphite and a titrimetric method for direct determination of sulphate. The observation that dithionate is not oxidized by hydrogen peroxide but is oxidized to sulphate by potassium chlorate-nitric acid mixture is the basis for estimation of dithionate.     

Rapid spectrophotometric determination of chromium(III)

A spectrophotometric procedure is suggested for the determination of Cr(III). The reaction between Cr(III) and 2-(5-bromo-2-pyridylazo)-5-dimethylaminophenol is accelerated by sodium dodecyl sulphate(SDS), sodium benzoate causes a further increase in the absorbance of the chelate. The optimum pH range for the reaction is 5-5.8(benzoate buffer). The chelate exhibits maximum absorbance at 590 nm, obeys Beer's law over the concentration range 0.02-0.56 microg/ml of Cr(III), has molar absorptivity of 7.8 x 10(4) 1. mol(-1) cm(-1) and a Sandell sensitivity of 0.66 ng/cm. The metal to ligand ratio is 1:2 in the absence of SDS and 1:1 in its presence. A procedure for the determination of Cr(III) and Cr(VI), when present together, is described. The method has been applied to the analysis of Cr(III) in tap water.     

The indirect spectrophotometric determination of the sulphate ion with 2-aminoperimidine

A new spectrophotometric determination of the sulphate ion is described which uses 2-aminoperimidine hydrochloride as a precipitating reagent. The excess of the reagent is measured at 305 nm. The procedure deals with sulphate in the range 4–120 p.p.m., and relies on simple calibration. The relative standard deviation for 50 p.p.m. of sulphate is 3.7%. The interference of 100 p.p.m. of phosphate, fluoride and nitrate is only slight in the determination of 50 p.p.m. of sulphate. The method is recommended for the determination of sulphate in rain and surface waters.     

Sulphate determination after its reduction to hydrogen sulphide and volatile separation by molecular absorption spectrometry

A rapid spectrophotometric method for sulphate determination in a discontinuous mode is described. The method is based on sulphate reduction to hydrogen sulphide followed by its volatilization and absorption in an alkaline solution. The reduction is obtained when a sulphate sample is heated to 287 degrees C for 15 min, with a mixture of Fe(o)/KI and phosphoric acid. The resulting gas is swept by nitrogen flow into a 0.1 M sodium hydroxide solution and the absorbance of the sulphide ions is measured directly at 230 nm. The proposed method enabled us to determine 50-700 mug of total sulphate with a relative standard deviation of the order of 5%. The method has been applied for the determination of sulphates in liquid (mineral waters) and solid (gypsiferous soils) samples.     

Sulphate preconcentration by anion exchange resin in flow injection and its turbidimetric determination in water

A preconcentration procedure was established for sulphate determination in rain waters at the mg/l level, employing a small column packed with the AG1-X8 (200-400 mesh) anionic resin inserted into a flow injection system. Sulphate determination was performed by using the turbidimetric method based on reaction with barium. For concentrations within 0.10 and 2.0 MgSO(2-)(4)/l, a throughput of 50 determinations/hr was achieved, and the relative standard deviation of results was better than 2%.     

Titrimetric determination of vanadium(IV) with cerium (IV)sulphate at room temperature using ferroin as indicator

A procedure has been developed for the visual titrimetric determination of vanadium(IV) with cerium(IV) sulphate, using ferroin is redox indicator. The method has been extended to the determination of iron(II) and vanadium(IV) in mixtures.     

Sensitive spectrophotometric determination of traces of zirconium with 2-(6-bromo-2-benzothiazolylazo)-5-diethylaminophenol in the presence of sodium lauryl sulphate

A simple and highly sensitive procedure for spectrophotometric determination of zirconium has been developed. At pH 4.6, zirconium reacts with 2-(6-bromo-2-benzothiazolylazo)-5-diethylaminophenol in the presence of sodium lauryl sulphate to form a red-violet complex, which has an absorption maximum at 520 nm. The molar absorptivity at 520 nm is 4.4 × 10⁵ 1.mole⁻¹ .cm⁻¹. Beer's law is obeyed for 0.25–1.50 μg of zirconium in 25 ml of solution. The method has been used in the determination of zirconium in aluminium alloy and steel samples.     

Determination of sulphate by pH titration

A simple and inexpensive method has been developed for the determination of sulphate and other very weak bases and acids. It utilizes the partial protonation of the weak base or the partial dissociation of the weak acid, which has not been exploited for analytical purposes thus far. The procedure consists of three pH titrations: one with a test solution of known sulphate content, the second with the sulphate sample, and the third with a blank. This method can be used in the presence of several inorganic ions and organic matrices, including non-aqueous solvents. In aqueous medium sulphate contents above 10(-3)M can be determined. The use of solvent mixtures may increase the sensitivity of the method by two orders of magnitude.     

Capillary electrophoresis determinations of trace concentrations of inorganic ions in large excess of chloride: soft modelling using artificial neural networks for optimisation of electrolyte composition

In this work, using a combination of experimental design (ED) and artificial neural networks (ANN), the composition of a triethanolamine-buffered chromate electrolyte was optimised for determination of sulphate anions in the presence of high chloride excess. The optimal electrolyte, allowing a baseline-resolved separation of sulphate from chloride present in a 1500 multiple excess in less than 170 s, consists of 10 mmol/L CrO(3), 2 mmol/L hexamethonium hydroxide, 10% methanol, and triethanolamine added to adjust the pH to 8.0. The method is suitable to a wide concentration range of chloride (4-1757 mg/L) and sulphate (4-590 mg/L) with linear calibration plots (R(2) = 0.9937-0.9999). Relative standard deviations are less than 2.0% for both anions for migration times and peak areas. The detection limits (hydrodynamic injection of 1 s) were 0.6 mg/L for sulphate and 0.5 mg/L for chloride. The method was successfully applied to determination of sulphate in mineral waters containing a high chloride concentration and to determination of sulphate traces in an anticancer drug injection preparation containing a physiological level of chloride. It was shown that alpha-cyclodextrin as an electrolyte additive has a significant potential for further increasing the separation selectivity for inorganic anions.     

Differential pulse polarographic study of the hydrolysis of endosulfan and endosulfan sulphate in emulsified medium. Application to the determination of binary mixtures of organochlorine pesticides

Hydrolysis reactions of endosulfan and endosulfan sulphate in the emulsified medium formed with ethyl acetate and a mixture of the two surfactants Hyamine 2389 and Triton X-405 are studied by differential pulse polarography. Besides the heptachlor-endosulfan sulphate pair, whose peak potentials are sufficiently different at pH 8.0 to allow their simultaneous determination, the organochlorine pesticide binary mixtures endosulfan-endosulfan sulphate, dieldrin-endosulfan and dieldrin-endosulfan sulphate can be determined based on their hydrolysis reactions in basic medium and on their different reaction rates. The endosulfan-endosulfan sulphate pair can be determined by allowing the mixture to hydrolyse at pH 11.0 and measuring the endosulfandiol peak for the determination of endosulfan. The analysis of the mixture dieldrin-endosulfan is based on endosulfan hydrolysis at pH 12.0 in which dieldrin is not hydrolysed. Dieldrin and endosulfan sulphate can also be determined simultaneously in a 0.5M sodium hydroxide medium. When determining one pesticide in binary mixtures containing a 5.0 x 10(-6)M concentration of the other pesticide, the lower limits of the calibrations obtained were: endosulfan-endosulfan sulphate mixture, 4.0 x 10(-6) and 1.0 x 10(-6)M respectively; heptachlor-endosulfan sulphate mixture, 2.0 x 10(-6)M for endosulfan sulphate; all other cases, 3.0 x 10(-6)M.     

The analytical kinetics of the titanium(III)-perchlorate reaction-I Homogeneous reaction kinetics

A spectrophotometric investigation has been made of the analytically relevant kinetics of the titanium(III)-perchlorate reaction in chloride and sulphate media. Sulphate media give better and more reproducible results. The reaction in sulphate medium is first-order in titanium(III) and hydrogen ion, but of fractional order in perchlorate. The pseudo third-order rate constant k(3)' for the rate equation has a value of 4.22 +/- 0.15 l(2) mol(-2) s(-1) at 49 degrees C. The energy of activation in sulphate medium is 84 +/- 4 kJ mol(-1), and in chloride medium is 80 +/- 12 kJ mol(-1). Small amounts of chloride m a sulphate medium, or of sulphate in a chloride medium, retard the reaction. The basis has been laid for a rate-measurement method for determination of perchlorate at low concentrations.     

Kinetochromic spectrophotometry-III Determination of fluoride by catalysis of the zirconimn-Methylthymol blue reaction

The determination of 0.5-4.75 mug of fluoride ion by its catalytic action upon the slow reaction between Methylthymol Blue and zirconium(IV) in aqueous solution is described. Calibration curves obtained after 60 min under optimal conditions are smooth, and yield an effective molar absorptivity of 3.23 x 10(4) 1.mole(-1)mm(-1) at 586 nm. There is considerably less cationic interference than in the alizarin complexan-cerium(III) or lanthanum procedure, but more serious anionic interference is encountered when phosphate, arsenate and, to a lesser extent, sulphate ions are present in the sample solution.     

Colorimetric determination of some important hydrazine derivatives

A simple and rapid colorimetric method for the determination of isoniazid, isocarboxazid, iproniazid phosphate, phenelzine sulphate and phenylhydrazine hydrochloride is described. The method is based on the formation of ferroin, when the studied drugs react with a mixture of iron (III) and 1,10-phenanthroline, and measurement of the absorbance at 512 nm. The procedure has been successfully applied to the assay of the pharmaceutical preparations of the studied drugs and the results are favorably comparable to the official methods.     

The titrimetric determination of sulphate,thiosulphate and polythionates in mining effluents

A titrimetric procedure is described for the determination of various forms of sulphur (sulphate, sulphite, thiosulphate, dithionate, tri- and tetrathionates after conversion to sulphate) in mining effluents. Metal ions are removed, after an oxidizing step, by a cationexchange resin, and the sulphate is precipitated with a known excess of 0.01 M barium chloride at pH 3.5. The excess of barium is back-titrated with standard 0.01 M ethylenediaminetetraacetic acid (EDTA) solution to a o-cresolphthalein complexone end-point at pH 11.0. The results obtained are in good agreement with those obtained by lengthy gravimetric procedures. Indirectly, dithionate can be determined, and sulphate and oxidizable thio salts such as thiosulphate and di-, tri-, and tetrathionates can be distinguished.     

Die bestimmung des gesamtschwefels in vulkanisierten gummimischungen

A method is described in which by means of a resin ion-exchanger the interference of foreign cations, particularly iron and chromium, can be prevented in the determination of total sulphur in vulcanized rubbers. The procedure allows the use of rapid volumetric methods for determining sulphate even when analyzing mixtures containing iron oxide or chromium oxide pigments. Here, the sulphate is precipitated with benzidine and determined by titration with sodium hydroxide solution. The method is quicker and more certain than the usual barium sulphate gravimetric procedure.     

Determination of Sulphate by Titrimetric and Colorimetric Measurement of Equivalent Displaced Zinc Ion

Abstract

Two methods are described for the determination of sulphate in the range of 200 μg to 100 mg by dissolving precipitated barium sulphate in excess of EDTA at pH 12.5. A titrimetric procedure involves back titration of excess EDTA with a standard zinc solution, while a complementary spectrophotometric method makes use of the stability of the barium EDTA complex in the presence of an excess of zinc ions; the latter are reacted with zincon and are equivalent to the amount of sulphate present.     

Quantitative Bestimmung von Sulfat und Sulfid (nach Oxydation) mit Hilfe des Orion-„Ionalizers“

A potentiometric procedure for the determination of sulphate has been tested. The analysis requires approx. 10–15 min time. The determination of the end-point is free from individual influences. In the determination of 0.1 N sodium sulphate an average error of the single measurement of fm=± 0.7% was observed. The more detailed complexometric method according to ?Deutsche Einheitsverfahren“ yielded an average mistake of fm=±2%. The method was applied to the determination of sulphate from sulphide (after oxidation of the latter). No considerable deviation from the gravimetrically ascertained values was noted. Borate does not interfere.     

Direct and rapid determination of sulphate in environmental samples with diffuse reflectance Fourier transform infrared spectroscopy using KBr substrate

The feasibility of employing diffuse reflectance Fourier transform infrared spectroscopy (DRS-FTIR) as a sensitive tool in the submicrogram level determination of sulphate (SO₄²⁻) was checked in this work. This paper presents the development of a new, rapid and precise analytical method for ppb levels of sulphate (SO₄²⁻) in environmental samples like coarse and fine aerosol particles, dry deposits and soil. The determination of submicrogram levels of sulphate is based on the selection of a quantitative analytical peak at 617 cm⁻¹ among the three observed vibrational peaks and preparing calibration curve using different known concentrations of sulphate by diffuse reflectance-Fourier transform infra red spectrometric (DRS-FTIR) technique. Pre-weighed and ground IR grade KBr was used as substrate over which remarkably wide range of known concentration of sulphate was sprayed and dried. The dried sample was analysed by DRS-FTIR. Three calibration curves for three different concentration ranges of sulphate were prepared for samples containing low and relatively higher sulphate contents. The relative standard deviation (n = 8) for the sulphate concentration ranges, 2.5-35.5, 25.5-165, 55-1000 μg/0.5 g KBr, as used to prepare calibration curves, were 2.4%, 2.1% and 1.5%, respectively. The relative standard deviation for the sulphate concentration in real samples were found to be in the range, 3.11-5.76% (n = 16), 4.05-7.75% (n = 16) and 1.48-3.52% (n = 10) for aerosol, dry deposits and soil, respectively. The LOD of the method is 0.20 μg/g SO₄²⁻. The F- and t-tests were performed to check the analytical quality assurance test. The noteworthy feature of the reported method is the non-interference of any of the associated anions and cations. The results were compared with that of ion-chromatographic method with high degree of acceptability. The method can be applied in wide concentration ranges. A method for sulphate determination was introduced that did not require pretreatment of samples. This method employed the direct determination of the sulphate. The method is reagent less, nondestructive, very fast, repeatable, and accurate and has high sample throughput value.     

A study of the direct spectrophotometric determination of uranium(VI) in trialkylamine extracts with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

A straightforward spectrophotometric method is described for the determination of uranium(VI) in trialkylamine sulphate extracts in kerosene diluent; 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP) is used for colour formation without resort to backextraction into an aqueous phase. The method provides good tolerance to sulphate ion and rapid colour development and appears to be free from interference when applied to extracts from uranium sulphate leach liquors.