聚铬黑T修饰电极检测亚硝酸盐的研究

利用电化学聚合法将铬黑T修饰到玻碳电极表面,制得聚铬黑T修饰电极。该修饰电极对亚硝酸盐的电化学氧化具有明显的催化作用,这种催化作用主要是由于聚铬黑T薄膜与带负电荷的亚硝酸盐离子的静电相互作用,导致亚硝酸盐离子富集在电极表面/溶液界面,显著增强了亚硝酸盐的氧化电流。电子传输系数α为0.735。选用0.85V作为工作电压,对亚硝酸盐进行安培检测,在0.05μmol/L～1.0 mmol/L和1.0～20.0 mmol/L两个浓度范围内呈现良好的线性关系,检测限达到0.01μmol/L。且该修饰电极有良好的重现性和稳定性。将该修饰电极用于泡菜中亚硝酸盐的测定,获得了满意的结果。     

亚硝酸根在磷钼镍杂多酸-聚吡咯膜修饰电极上的伏安行为及其含量测定

研究了亚硝酸根(NO     

原位电化学还原制备石墨烯修饰玻碳电极及其对亚硝酸根离子的电催化氧化性能

通过原位电化学还原直接制备石墨烯修饰玻碳电极,并用电化学阻抗谱（EIS）和扫描电子显微镜（SEM）对其进行了表征,研究了亚硝酸根离子（NO2-）在石墨烯修饰玻碳电极上的电化学行为.结果表明：石墨烯修饰玻碳电极对NO2-的氧化反应有良好的电催化活性,NO2-的浓度与峰电流呈良好的线性关系,且在pH 7.0的磷酸盐缓冲液（PBS）中其氧化峰电流最高.利用该方法测定了模拟废水中NO2的含量,结果令人满意.     

NO2-在CTMAB-氧化钕纳米修饰电极上的电化学行为及其测定

制备了十六烷基三甲基溴化铵-氧化钕纳米修饰电极。用循环伏安法和示差脉冲伏安法研究了NO2-在该修饰电极上的电化学行为,结果表明,该修饰电极对NO2-的氧化具有良好的电催化能力,NO2-的氧化峰电流与其浓度在3.33×10-8～1.04×10-6mol/L范围内呈现良好的线性关系,检测限为9.86×10-9mol/L(S/N=3)。此外,该修饰电极具有良好的重现性和稳定性。本方法可用于NO2-实际样品的测定。     

Electrochemically promoted photocatalytic oxidation of nitrite ion by using rutile form of TiO2/Ti electrode

The photocatalytic oxidation of nitrite ion in a NaCl aqueous solution using the rutile form of TiO₂/Ti as the working electrode was studied. Experimental results indicate that the rutile form of TiO₂/Ti film electrode has excellent photoactivity by applying a bias potential and irradiation simultaneously. The incident photo-to-current conversion efficiency (IPCE) of this working electrode is a function of the applying bias potential. The photocurrent efficiency of nitrite ion oxidation was 33–40% at a pH of about 7. The oxidation rate of the nitrite ion in brine wastewater using the rutile form of TiO₂/Ti electrode can be estimated by photocurrent measurements. The applying bias potential, light power and pH value were the major factors affecting the oxidation rate and the photocurrent efficiency of nitrite ion oxidation, while the concentrations of nitrite ion was minor.     

Electrochemical study and flow-injection amperometric detection of trace NO(2)(-) at CuPtCl(6) chemically modified electrode

A thin film of mixed-valent CuPtCl₆ is deposited on a glassy carbon electrode by continuous cyclic scanning in a solution containing 3×10⁻³ M CuCl₂+3×10⁻³ M K₂PtCl₆+1 M KCl in the potential range from 700 to −800 mV. The cyclic voltammetry is used to study the electrochemical behaviors of nitrite on CuPtCl₆/GC modified electrode and the electrode displays a good catalytic activity toward the oxidation of nitrite. The effects of the film thickness, pH, the electrode stability and precision have been evaluated. Experiments in flow-injection analysis are performed to characterize the electrode as an amperometric sensor for the detection of nitrite. The modified electrode shows a wide dynamic range, quite a low detection limit and short response time. The linear relationship between the flow-injection peak currents and the concentrations of nitrite is at a range of 1×10⁻⁷–2×10⁻³ M with a detection limit of 5×10⁻⁸ M.     

Determination of nitrate and nitrite in mixtures with a nitrate ion electrode

A rapid method for the determination of nitrate and nitrite ions is described. The potential of a mixture of nitrate and nitrite was measured with a nitrate ion selective electrode. The nitrite in the mixture is then oxidized to nitrate with permanganate in acid solution, and the potential of the oxidized solution is also measured with the electrode. The fundamental equations for the response of the nitrate ion electrode to nitrate ion in the presence of interfering ions were used, and a new equation was developed for calculating the original nitrate concentration of the mixture. The absolute errors for solutions of known concentrations (2.5–100 p.p.m. each) were 1.8 p.p.m. nitrate and 2 p.p.m. nitrite. When the results are calculated by computer, five determinations can be performed in 30 min. The method was applied to the determination of the oxides of nitrogen in cigarette smoke as nitrite and nitrate after dissolution in basic solution.     

A sensitive and selective nitrite sensor based on a glassy carbon electrode modified with gold nanoparticles and sulfonated graphene

We describe a highly sensitive and selective amperometric sensor for the determination of nitrite. A glassy carbon electrode was modified with a composite made from gold nanoparticles (AuNPs) and sulfonated graphene (SG). The modified electrode displays excellent electrocatalytic activity in terms of nitrite oxidation by giving much higher peak currents (at even lower oxidation overpotential) than those found for the bare electrode, the AuNPs-modified electrode, and the SG-modified electrode. The sensor has a linear response in the 10 μM to 3.96 mM concentration range, a very good detection sensitivity (45.44 μA mM^?1), and a lower detection limit of 0.2 μM of nitrite. Most common ions and many environmental organic pollutants do not interfere. The sensor was successfully applied to the determination of nitrite in water samples, and the results were found to be consistent with the values obtained by spectrophotometry.

A novel nitrite sensor based on poly-1-naphthylamine doped by a ferrocenesulfonic-acid-modified electrode

A novel sensor for detecting nitrite based on poly-1-naphthylamine doped by a ferrocenesulfonic acid (PNAFc) modified electrode has been proposed. X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM) have confirmed that ferrocene-sulfonic acid (Fc) can be doped in poly-1-naphthylamine (PNA) and enhances its electrochemical activity. In a nitrite solution, the PNAFc electrode shows an excellent electrocatalytic activity for the oxidation of nitrite. Based on differential pulse voltammetry (DPV), the response was evaluated with respect to pH, scan rate, temperature, and other variables. The optimum analytical conditions for the determination of nitrite were established. Under optimum conditions, the linear range for nitrite determination was from 0.5 to 100 μM with a detection limit of 0.5 μM. The stability and anti-interference ability of the PNAFc electrode were also evaluated. The results indicate that this sensor is feasible for the determination of nitrite in real water samples. The text was submitted by the authors in English.     

Determination of nitrite based on mediated oxidation at a carbon paste electrode modified with a ruthenium polymer

The use of carbon paste electrodes modified with [Ru(bpy)(2)(PVP)(10)Cl]Cl for the mediated detection of nitrite is described. This surface modifier substantially lowers the overpotential for nitrite oxidation, hence permitting its determination at a lower potential. Various electrode characteristics were optimized, including the modifier loading and the monitoring potential, using batch amperometry. Standard calibration curves yielded slopes of 0.30 microA/microM over the linear range 5 x 10(-8)-5 x 10(-4)M nitrite with a detection limit of 3 x 10(-8)M (1.38 ppb) nitrite. The modified electrode response was shown to be relatively stable over a period of 5 days with a signal diminution of 8%. Electrode-to-electrode precision was measured as 11.4%. Flow-injection studies indicated the suitability of this electrode as a detector in flowing streams.     

亚硝酸根在纳米金修饰玻碳电极上的电催化氧化行为及其测定

采用直接电化学沉积法制备出纳米金修饰玻碳电极,研究了其对亚硝酸根的电催化氧化作用。结果表明,亚硝酸根在该修饰电极上于0.8 V处出现了一个良好的氧化峰。在最优实验条件下,亚硝酸根的峰电流与其浓度在2×10-6～2×10-3mol/L范围内呈一定的线性关系,检出限为6.0×10-7(S/N=3),提出了用循环伏安法测定亚硝酸根的方法。纳米金修饰电极用于东莞自来水水样中亚硝酸根的测定,回收率在98.1%～101.4%之间。对比本方法,用分光光度法对东莞自来水样中亚硝酸根进行了测定,结果满意。     

Electrocatalytic Oxidation and Determination of Nitrite at Multi‐walled Carbon Nanotubes Modified Carbon Ceramic Electrode

In the present work, the electrochemical oxidation of nitrite on carbon ceramic electrode (CCE) modified with multi‐walled carbon nanotubes (MWCNTs) was investigated. The modified electrode exhibited catalytic activity toward the electrooxidation of nitrite. Experimental parameters such as solution pH, scan rate, concentration of nitrite and nanotubes amount were studied. It was shown nitrite can be determined by differential pulse voltammetry (DPV) and hydrodynamic amperometry (HA) using the modified electrode. Under the optimized conditions the calibration plots are linear in the concentration ranges of 15‐220 and 50‐3000 μM with limit of detections of 4.74 and 35.8 μM for DPV and HA, respectively. The modified electrode was successfully applied for analysis of nitrite in spinach sample. The results were favorbly compared to those obtained by UV‐Visible spectrophotometric method. The results of the analysis suggest that the proposed method has promise for the routine determination of nitrite in the examined products.     

Simultaneous electrochemical determination of nitrate and nitrite in aqueous solution using Ag-doped zeolite-expanded graphite-epoxy electrode

In this work a new electrochemical sensor based on an Ag-doped zeolite-expanded graphite-epoxy composite electrode (AgZEGE) was evaluated as a novel alternative for the simultaneous quantitative determination of nitrate and nitrite in aqueous solutions. Cyclic voltammetry was used to characterize the electrochemical behavior of the electrode in the presence of individual or mixtures of nitrate and nitrite anions in 0.1 M Na₂SO₄ supporting electrolyte. Linear dependences of current versus nitrate and nitrite concentrations were obtained for the concentration ranges of 1-10 mM for nitrate and 0.1-1 mM for nitrite using cyclic voltammetry (CV), chronoamperometry (CA), and multiple-pulsed amperometry (MPA) procedures. The comparative assessment of the electrochemical behavior of the individual anions and mixtures of anions on this modified electrode allowed determining the working conditions for the simultaneous detection of the nitrite and nitrate anions. Applying MPA allowed enhancement of the sensitivity for direct and indirect nitrate detection and also for nitrite detection. The proposed sensor was applied in tap water samples spiked with known nitrate and nitrite concentrations and the results were in agreement with those obtained by a comparative spectrophotometric method. This work demonstrates that using multiple-pulse amperometry with the Ag-doped zeolite-expanded graphite-epoxy composite electrode provides a real opportunity for the simultaneous detection of nitrite and nitrate in aqueous solutions.     

Pencil Lead Electrode Modified with Hemoglobin Film as a Novel Biosensor for Nitrite Determination

In the present paper, the electrochemical reduction of nitrite at a hemoglobin modified pencil lead electrode (Hb/PLE) is described. The electrochemical properties of nitrite were studied by cyclic voltammetry and chronoamperometry. Results showed that the hemoglobin film has an excellent electrochemical activity towards the reduction of nitrite. By using voltammetric and chronoamperometric methods, α, n_α and n were calculated. Then the ability of the electrode for nitrite determination was investigated using differential pulse voltammetry. The electrocatalytic reduction peak currents were found to be linear with the nitrite concentration in the range from 10 to 220 µM with a detection limit of 5 µM. The relative standard deviation is 2 % for 3 successive determinations of a 100 µM nitrite solution. This modified electrode was successfully used for the detection of low amounts of NO₂^? in spinach sample and a spiked sample of tap water.     

Development of a paper-based,inexpensive, and disposable electrochemical sensing platform for nitrite detection

Electrochemical techniques are attractive for nitrite detection owing to their intrinsic advantages. However, traditional electrochemical sensors often suffer from the effects of fouling due to the adsorption of oxidation products on the electrode surface. In this work, a paper-based, inexpensive, disposable electrochemical sensing platform was developed for nitrite analysis based on a simple and efficient vacuum filtration system. Taking advantage of the physicochemical properties of graphene nanosheets and gold nanoparticles, the mass transport regime of nitrite at the paper-based electrode was thin layer diffusion rather than planar diffusion. In comparison with the electrochemical responses of commercial gold electrodes and glassy carbon electrodes (GCE), a considerably larger current signal was seen at the paper-based sensing interface, which significantly improved its sensitivity for nitrite detection. In particular, the paper-based electrode was a disposable sensing device, so that it effectively avoided the fouling effect arising from the adsorption of oxidation products. Moreover, the paper-based sensing platform made it possible to determine nitrite in environmental and food samples in an accurate, convenient, inexpensive, and reproducible way, indicating that the proposed system is promising for practical applications in environmental monitoring and public health.     

Electrochemical sensor of nitrite based on an inorganic film modified glassy carbon electrode

The electrocatalysis of nitrite in solutions at an inorganic film modified glassy carbon electrode was studied. The modifier was an electrodeposited thin inorganic film of the copper-heptacyanonitrosylferrate (CuHNF). Cyclic voltammetry of the modified electrode in a nitrite solution revealed that both oxidation and reduction of nitrite were catalyzed and the electrocatalytic currents were controlled by the diffusion of nitrite. Voltammetric and amperometric responses were investigated. When applied as an amperometric sensor in a flow injection system, the modified electrode permitted detection at — 0.55 V, over 500 mV lower than at the naked electrode surface. A linear response range extending from 1 × 10^–6 to 1 × 10^–3 M nitrite was obtained, with a detection limit of 3 × 10^–7 M. The relative standard deviation for 50 repetitive injections with a 5 × 10^–5 M nitrite solution was less than 4%. The procedure was applied to the determination of nitrite in saliva and nitrate.     

吸附杂多化合物对亚硝酸根的电催化还原

详细地研究了吸附在热解石墨电极表面的ＳｉＭｏ１２Ｏ４０４－以及Ｄｙ（ＳｉＭｏ１１Ｏ３９）２１３－和吸附在玻碳电极表面的Ｐ２Ｗ１８Ｏ６２６－的电化学行为，结果表明这些杂多化合物修饰电极在酸性条件下均对ＮＯ２－的还原有很好的催化作用，其催化电流与ＮＯ２－的浓度的平方根里线性关系。     

Preparation of Pt/MWCNTs Catalyst by Taguchi Method for Electrooxidation of Nitrite

Abstract—The Pt nanoparticles-functionalized multiwall carbon nanotubes (f-MWCNTs) modified glassy carbon electrodes were used to study the electrooxidation of nitrite. Pt nanoparticles were electrodeposited on the f-MWCNTs modified glassy carbon (GC) electrode by applying a constant potential to the electrode for a specific time. By applying optimized conditions (using Minitab software), Pt/MWCNTs/GC electrode was prepared by immobilizing 40 μL of f-MWCNTs on the GC electrode and applying a potential of–0.20 V vs. Ag/AgCl for 120 s. The electrooxidation of nitrite was studied on the prepared electrode in 0.1 M KCl solution. The amperometric response of the prepared electrode linearly changes with the concentration of nitrite from 4.0 μM to 2.4 mM. The detection limit of the electrode was found to be 1.5 μM (S/N = 3) with a sensitivity of 28.7 μA/mM.     

Electroreduction of nitrite on gold electrode modified with Cu-containing nitrite reductase model complex

A gold electrode modified with copper complexes containing a tridentate aromatic amine compound (bis(6-methyl-2-pyridylmethyl)amine ethyl sulfide, which is a model for the nitrite reduction centre of copper-containing nitrite reductase, catalyzed electrochemically the reduction of nitrite to nitrogen monoxide under acidic conditions.     

Nanoporous Gold Leaf for Amperometric Determination of Nitrite

Ultra‐thin free‐standing nanoporous gold leaf made by dealloying exhibits excellent electrocatalytic activities toward nitrite oxidation. The electrochemical responses of nitrite ions on this novel nano‐electrode is found not dependent on pH over a wide range from 4.5 to 8.0, which is markedly different from that of gold oxidation, a process known to be highly pH‐sensitive. Amperometric study shows a linear relationship for nitrite determination in a concentration range from 1 µM to 1 mM. This nanostructured gold electrode displays good stability, repeatability and selectivity which suggests its potential for the development of new electrochemical sensors.