Stable superhydrophobic fluorine containing polyfluorenes

Fluorene-based polymers containing perfluorooctyl moieties were designed and synthesized.The high electronegativity and F…H-C interactions are present in the fluorinated polymers,which slightly induce blue-shift of UV-Vis absorption in film.The fluoropolymer films prepared from fluorinated solvents show lager contact angles than those prepared in non-fluorinated solvents.     

Inferring wettability of heterogeneous surfaces by ToF-SIMS

Time-of-flight secondary ion mass spectrometry (ToF-SIMS) has been examined as a possible predictive tool for surface wettability. Heterogeneous surfaces were prepared with hydrophilic and hydrophobic regions of known surface coverage using self-assembled monolayers. The surface coverage of each component was then correlated with ToF-SIMS fragmentation of the hydrophobic and hydrophilic surface groups and static contact angle measurements. From these measurements, a clear relationship between the surface wettability and relative intensity of characteristic secondary ions was identified. Moreover, our results for planar surfaces can be extrapolated to predict the wettability of particulate samples for which direct contact angle measurements are not straightforward. The ability to infer particle wettability by ToF-SIMS is well suited to mineral characterization and in particular, the prediction of mineral flotation efficiencies.     

On the role of energy barriers in determining contact angle hysteresis

The thermodynamic model of contact angles on rough, heterogeneous surfaces developed by Long et al. [J. Long, M.N. Hyder, R.Y.M. Huang and P. Chen, Adv. Colloid Interface Sci. 118 (2005) 173] was employed to study the role of energy barriers in determining contact angle hysteresis. Major energy barriers corresponding to metastable states and minor energy barriers corresponding to secondary metastable states were defined. Distributions of major and/or minor energy barriers as a function of apparent contact angle for various surfaces were obtained. The reproducibility of contact angle measurement, the effect of vibrational energy on contact angle hysteresis and the "stick-slip" phenomenon were discussed. Quantitative relations between contact angles and vibrational energy were obtained. It was found that receding contact angles are normally poorly reproducible for hydrophilic surfaces, but for extremely hydrophobic surfaces, advancing contact angles may have a poor reproducibility. When the vibrational energy available to a system increases, the measured advancing contact angle will decrease while the receding angle will increase until both reach a common value: the system equilibrium angle. This finding not only agrees well with the experimental observations in system equilibrium contact angle measurements, but also lays a theoretical foundation for such measurements. A small vibrational energy may result in a "stick-slip" phenomenon.     

Physico-chemical and thermodynamic aspects of fibroblastic attachment on RGDS-modified chitosan membranes

In the present study, the cell attachment/spreading behaviour of L929 mouse fibroblasts on chitosan membranes was evaluated by using physico-chemical properties. For this purpose chitosan membranes were prepared and then photochemically modified with the cell adhesive peptide RGDS (Arg-Gly-Asp-Ser). The physico-chemical properties of unmodified (CHI) and RGDS-modified chitosan (CHI-RGDS) membranes were evaluated by calculating surface free energy (γ_sv) and interfacial free energy (γ_sw) values using captive bubble contact angle measurements and harmonic mean equation. The cell attachment experiments were performed both in 10% FBS containing and serum-free media with CHI and CHI-RGDS membranes. Eventually, it was not possible to predict a direct relationship between the change in physico-chemical properties and L929 cell attachment behaviour. The experimental results obtained from cell attachment agree with the theoretical prediction for the free energy of adhesion except for the cell attachment on CHI membrane in serum-free medium. Although a negative interfacial free energy of adhesion was calculated for CHI membrane in serum-free medium (ΔF_adh = −2.19 ergs/cm²), the cell attachment was poor (70%) compared to CHI-RGDS (90%) and none of the cells were spread on CHI surface to gain a fibroblastic morphology. Negative energy of adhesion was calculated for CHI and CHI-RGDS in 10% FBS medium, in which 100% of cells were attached on the membranes correlating with the thermodynamic approach. It can be suggested that, adsorption of serum proteins strongly affected the cell attachment meanwhile the presence of biosignal RGDS molecules triggered the cell spreading in serum medium.     

Review of non-reactive and reactive wetting of liquids on surfaces

Wettability is a tendency for a liquid to spread on a solid substrate and is generally measured in terms of the angle (contact angle) between the tangent drawn at the triple point between the three phases (solid, liquid and vapour) and the substrate surface. A liquid spreading on a substrate with no reaction/absorption of the liquid by substrate material is known as non-reactive or inert wetting whereas the wetting process influenced by reaction between the spreading liquid and substrate material is known as reactive wetting. Young's equation gives the equilibrium contact angle in terms of interfacial tensions existing at the three-phase interface. The derivation of Young's equation is made under the assumptions of spreading of non-reactive liquid on an ideal (physically and chemically inert, smooth, homogeneous and rigid) solid, a condition that is rarely met in practical situations. Nevertheless Young's equation is the most fundamental starting point for understanding of the complex field of wetting. Reliable and reproducible measurements of contact angle from the experiments are important in order to analyze the wetting behaviour. Various methods have been developed over the years to evaluate wettability of a solid by a liquid. Among these, sessile drop and wetting balance techniques are versatile, popular and provide reliable data. Wetting is affected by large number of factors including liquid properties, substrate properties and system conditions. The effect of these factors on wettability is discussed. Thermodynamic treatment of wetting in inert systems is simple and based on free energy minimization where as that in reactive systems is quite complex. Surface energetics has to be considered while determining the driving force for spreading. Similar is the case of spreading kinetics. Inert systems follow definite flow pattern and in most cases a single function is sufficient to describe the whole kinetics. Theoretical models successfully describe the spreading in inert systems. However, it is difficult to determine the exact mechanism that controls the kinetics since reactive wetting is affected by a number of factors like interfacial reactions, diffusion of constituents, dissolution of the substrate, etc. The quantification of the effect of these interrelated factors on wettability would be useful to build a predictive model of wetting kinetics for reactive systems.     

Wetting of heterogeneous surfaces of block copolymers containing fluorinated segments

 The wetting of well-characterized heterogeneous surfaces of block copolymers has been studied by low-rate dynamic contact angle measurements using axisymmetric drop-shape analysis. Atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) were used to investigate the roughness, the heterogeneity and the chemical composition of the surfaces. By changing the block length of polysulfone and semifluorinated polyester segments in the block copolymers, the surface heterogeneity of thin films prepared on silicon wafers could be controlled. Tapping-mode AFM measurements showed that soft, hydrophobic domains of varying size on the submicrometer length scale were obtained on these surfaces (60–250 nm). The mean roughness was of the order of several nanometers. The results of the contact angle measurements showed that neither roughness nor heterogeneity had a significant effect on the advancing contact angle of water, at the scale of the features present; however, the contact angle hysteresis increased with increasing percentage of the soft domains. We assume that liquid retention by the solid upon retraction of the three-phase line is the main cause for the observed increase in contact angle hysteresis. Concerning the molecular composition of these block copolymer surfaces, angle-resolved XPS analysis showed a surface segregation of fluorine within the surface region. A direct correlation was found between the fluorine content of the block copolymer surfaces and the advancing contact angle of water. Received: 26 May 2000 Accepted: 3 January 2001     

Determination of the second step microstructure for superhydrophobic surfaces

A selection of suitable microstructures is critical to fabrication and properties of superhydrophobic surfaces (SHS). In this study, we introduce a three‐dimensional droplet model to thermodynamically analyze the superhydrophobic properties for the purpose of determining the second step of a two‐step microstructure suitable for the SHS based on the common models within the reach of the existing macro‐machining technology. It is found that a sinusoidal microstructure is the most suitable, followed by a cone frustum and a prism in the composite wetting state, as well as the transition from hydrophilic to hydrophobic depends basically on the solid fraction rather than non‐determinative surface microscopic topography. The predictions of the model are found in quite good agreement with the experimental observations. This study will facilitate fabrication of the SHS on how to select the suitable morphology. Copyright © 2012 John Wiley & Sons, Ltd.     

Protein adsorption and wetting of the protein adsorbed surfaces studied by a new type of laser reflectometer

We have devised a new type of laser reflectometer that can measure adsorption behavior of (bio)-polymers, such as proteins, on the substrate surface and also the wetting for the surface of adsorbed layer of such (bio)-polymers. The adsorption and the wetting experiments can be conducted in a sequential manner using the same sample by this apparatus. So, the wetting of the surface of protein-adsorbed layer can be measured in virtually intact state. The reflectometry is based on the traditional optical polarimetry and the wetting measurement is due to the dropping time method (DTM) that has been reported before by the authors. The two methods are combined in an apparatus and hence we can correlate the wetting of protein layer adsorbed on the substrate surfaces with the amounts of protein molecules on the surface. As a model case we demonstrate the adsorption of several typical water soluble globular proteins on stainless steel surfaces. For this combination of the adsorbent with adsorbates, it is found that the water wetting of the protein adsorbed surface is closely related with the adsorbed amounts of proteins not depending on species.     

Status of the three-phase line tension: a review

From a thermodynamic point of view, the concept of line tension is on solid ground; it is well recognized and defined. There is a notion in the literature that there is little consensus with regards to magnitude or sign of line tension. Partly, inappropriate comparisons of line tension values may have contributed to the current uncertainty, especially some between theoretical and experimental values. A wide range of reported line tension values may not necessarily be a result of conflicting findings, but it may reflect the diversity of systems studied. However, differences among similar approaches and systems observed are sometimes caused by one or several of the following factors: difficulties in sample preparation, poor experimental techniques, non-equilibrium, or conceptual and theoretical difficulties and oversimplifications. It is important to clearly establish the magnitude and sign of line tension as it may determine its relevance to technological applications such as microfluidic systems.

This review has examined a wide range of recent and past studies on the subject of line tension. The review classifies line tension studies into theoretical and experimental; it further groups the studies into liquid–liquid–vapor and solid–liquid–vapor systems for each category. The review provides a comparison between similar studies in an attempt to clarify the current status of line tension research. The majority of theoretical line tension studies (excluding the near wetting studies) have estimates for line tension of about 10⁻¹⁰ N; however, for special cases, values as high as 10⁻⁶ N are also reported. There is less consensus regarding the sign for the line tension as theoreticians often assert that line tension can have either a positive or a negative sign. In experimental studies of liquid–liquid–vapor systems the majority of studies reported positive values for line tension; for film studies, the magnitude of line tension reported was between 10⁻⁹ and 10⁻⁷ N, whereas for studies of liquid lens values as high as 10⁻⁶ N were also reported. The clear majority of studies for solid–liquid–vapor systems reported a positive sign for line tension. In studies involving particles, line tension values ranged from 10⁻⁹ to 10⁻⁶ N. Studies using drop size dependence of contact angles reported values mostly in the span of 10⁻⁹–10⁻⁶ N; however, a clear majority of the reported values fell in the higher end of the above range. The special topic of line tension near wetting was also studied. While the interface displacement model appears to have brought about consensus with respect to certain aspects of line tension behavior near wetting, this model maybe still too phenomenological to be satisfactory from a more fundamental standing. Experimentalists have just begun studying line tension for systems near wetting, this is encouraging, but more comprehensive studies are needed.     

超疏水性材料表面的制备、应用和相关理论研究的新进展

文章总结了Wenzel方程、Cassie方程及一种具有极高精确度的,可方便测出固体表面上液滴前进角和后退角的测试方法等超疏水表面的最新理论研究成果;回顾了溶胶凝胶法、化学修饰法、喷涂法、液相法、化学蚀刻法、水热法、微相分离法、原位聚合法、静电纺丝法、阳极氧化法等近几年出现的超疏水表面的制备方法;介绍了在微物质能量、生物医学、光学、燃料以及电池应用等领域超疏水表面的最新功能性的应用。最后,客观地展望了超疏水表面制备及理论研究的发展方向。     

Effect of various treatment and glazing (coating) techniques on the roughness and wettability of ceramic dental restorative surfaces

Surface treatment procedures such as grinding and polishing are needed to provide the ceramic dental restorative materials with proper fitting and occlusion. The treated surfaces are customarily glazed to improve the strength and smoothness. Though smoothness and wetting of the dental surfaces are important to minimize bacterial plaque retention, influence of the surface treatment and glazing procedures on the final surface roughness and its correlation to wettability are overlooked.

In this work, effect of various treatment (diamond fraising, stoning, sanding and aluminum oxide and rubber polishing) and glazing (auto and overglazing) techniques on the final roughness and the resulting wettability of dental ceramic surfaces were investigated using scanning electron microscopy (SEM) observations and atomic force microscopy (AFM) scans, 75 scans per sample. The surfaces were characterized and assigned an average roughness measure, R_a. The wettability of the same surfaces was evaluated using micro-contact angle measurements (25 micro-bubbles placed on a grid on each surface) to correlate the final surface roughness and wettability.

The results show that overglazing prevails over surface irregularities from different treatment procedures and provides homegeneously smooth surfaces with mean R_a < 10 nm. It also produces uniformly wetted surfaces with low contact angles around 20°. The autoglazed surfaces are less smooth (mean R_a around 50 nm) and displays sporadic topographic irregularities. They display larger and less uniform contact angles ranging between 35° and 50°. The results suggest that overglazing should be preferred after surface treatment to obtain a smooth and well-wetted dental ceramic surface.     

Manipulating microobject by using liquid droplet as a transporting vehicle

Wetting in the system hematite–water–diisobutyl ketone was studied in the presence of an anionic surfactant, hexadecyl sulfonic acid. Adsorption isotherms of surfactant on hematite powder were measured separately at the interfaces between hematite–water and hematite–ketone, and the interfacial tension of the water–ketone interface was determined as a function of surfactant concentration. The Gibbs and Young’s equations were used to calculate contact angles from the adsorption data. For comparison, contact angles were measured as a function of surfactant concentration on the face of a hematite crystal selected from the same supply of specular hematite used for preparing the hematite powder. Overall, contact angles calculated from the equations correlate closely with measured contact angles.     

利用等离子体技术研究聚苯乙烯表面的接枝聚合反应

用O₂等离子体对聚苯乙烯(PS)进行预处理, 再用Ar等离子体引发N-乙烯基吡咯烷酮(NVP)在其表面接枝聚合. 通过接触角(CA)及表面自由能(SE)分析, 探讨了O₂等离子体预处理条件对PS表面自由能的影响, 确定了预处理的最佳条件. 通过衰减全反射红外光谱(ATR-FTIR)、X射线光电子能谱(XPS)和动态接触角(DCA)分析, 比较了O₂等离子体预处理前后和接枝聚合前后PS的表面组成及表面性能, 实验结果表明, 利用等离子体技术能成功地将NVP接枝聚合于PS表面, 接枝聚合后的PS表面由于极性高分子链和粗糙度的增加, 亲水性增强, 水滴易在其表面铺展. 由于接枝聚合后PS表面的高分子链在水中发生重构, 使后退角降低幅度较大, 接触角滞后现象明显.     

A modified Cassie–Baxter relationship to explain contact angle hysteresis and anisotropy on non-wetting textured surfaces

The Cassie–Baxter model is widely used to predict the apparent contact angles obtained on composite (solid–liquid–air) superhydrophobic interfaces. However, the validity of this model has been repeatedly challenged by various research groups because of its inherent inability to predict contact angle hysteresis. In our recent work, we have developed robust omniphobic surfaces which repel a wide range of liquids. An interesting corollary of constructing such surfaces is that it becomes possible to directly image the solid–liquid–air triple-phase contact line on a composite interface, using an electron microscope with non-volatile organic liquids or curable polymers. Here, we fabricate a range of model superoleophobic surfaces with controlled surface topography in order to correlate the details of the local texture with the experimentally observed apparent contact angles. Based on these experiments, in conjunction with numerical simulations, we modify the classical Cassie–Baxter relation to include a local differential texture parameter which enables us to quantitatively predict the apparent advancing and receding contact angles, as well as contact angle hysteresis. This quantitative prediction also allows us to provide an a priori estimation of roll-off angles for a given textured substrate. Using this understanding we design model substrates that display extremely small or extremely large roll-off angles, as well as surfaces that demonstrate direction-dependent wettability, through a systematic control of surface topography and connectivity.     

The exponential power law: partial wetting kinetics and dynamic contact angles

An equation for the kinetics of partial drop spreading is proposed. This equation was empirically derived from experimental data for the spreading kinetics of partially wetting liquids in terms of the wet area versus time. The equation has the form of an exponential power law (EPL), and transforms into the well-known power law for complete wetting, when the equilibrium contact angle approaches zero. The EPL fits very well available experimental data. To lend additional support to the validity of this generalized equation, it will be demonstrated that when it is transformed to present the dynamic contact angle (DCA), it fits very well DCA experimental data for other wetting processes, such as capillary flow and tape coating.     

Synthesis of novel soluble poly(imide-siloxane)s via hydrosilylation: Characterization and structure property behaviour

A series of novel poly(imide-siloxane)s (PIS) were synthesized by the grafting of amine terminated soluble imides to the siloxane backbone. The amine terminated imides were synthesized by choosing suitable anhydrides and amines to get the imides that are soluble in polar and non-polar solvents. The imides were grafted to the siloxane backbone by the epoxy group cleavage. All the polymers were obtained in quantitative yields with the inherent viscosities ranging from 0.22 to 1.2 dL g⁻¹. The polymers were characterized by FT-IR, ¹H and ¹³C NMR, and were examined for their thermal properties. The polymers were found to be stable up to a temperature 350 °C. The DSC results showed a single glass transition in the negative temperature, whereas the DTA revealed another glass transition in the positive end for some of the polymers showing phase separation. Polymer films were prepared employing the coupling reaction between PIS and the polydimethylsiloxane matrix by varying the amount of incorporation of PIS in the films. The polymer films had a tensile strength of 35-82 MPa with a percentage elongation of 86-271%. The contribution of polar and dispersion component towards the total surface energy was studied by the contact angle measurement and a reduction in surface tension of 14 mN m⁻¹ was achieved with the fluorine containing PIS membrane.     

液滴在不互溶液体表面上的相对界面自由能曲面及Neumann三角形的导出

根据系统的界面Helmholtz自由能自发地趋于最低的热力学原理,以浮在不互溶液体(2)表面上透镜状液滴(3)在气(1)、液₂、液₃三相交界处,气-液₃、液₂-液₃界面各自和气-液₂界面通过液滴内部的夹角θ₁、θ₂为变量(0°≤θ₁≤180°,0°≤θ₂≤180°),证明出3个界面张力γ₁₂、γ₁₃、γ₂₃各种可能组合情况下液体₃稳定时的θ₁、θ₂值与它们之间的关系,导出Neumann三角形;并按照计算数据绘出几种类型相对于气相中圆球形液滴的界面自由能曲面图。     

Calculating the surface tension between a flat solid and a liquid: a theoretical and computer simulation study of three topologically different methods

We discuss three topologically different methods for calculating the surface tension between a flat solid and a liquid from theoretical and computer simulation viewpoints. The first method, commonly used in experiments, measures the contact angle at which a static droplet of liquid rests on a solid surface. We present a new analysis algorithm for this method and explore the effects of line tension on the contact angle. The second method, commonly used computer simulations, uses the pressure tensor through the virial in a system where a thick, infinitely extended slab of liquid rests on a solid surface. The third method, which is original to this paper and is closest to the thermodynamic definition of surface tension, applies to a spherical solid in contact with liquid in which the flat solid is recovered by extrapolating the sphere radius to infinity. We find that the second and third methods agree with each other, while the first method systematically underestimates surface tension values.     

Adhesion of Cryptosporidium parvum and Giardia lamblia to solid surfaces: the role of surface charge and hydrophobicity

Adhesion of Cryptosporidium parvum and Giardia lamblia to four materials of different surface charge and hydrophobicity was investigated. Glass beads were used with and without three polymer coatings: aminosilines (A0750), fluorosilines (T2494), an amino cationic polymer. Surface charge density and hydrophobicity of the beads were characterized by measuring the zeta potential (ZP) and the contact angle, respectively. Adhesion was derived from batch experiments where negatively charged (oo)cysts were mixed with the beads and recovery was determined by counting (oo)cysts remaining in suspension using a flow cytometer. Experimental results clearly show that adhesion to solid surfaces of C. parvum is different from G. lamblia. Adhesion of C. parvum to positively charged, hydrophilic beads (82% recovery relative to control) indicated that surface charge was the more important factor for C. parvum, dominating any hydrophobic effects. Adhesion of G. lamblia cysts to negatively charged, hydrophobic beads (0% recovery relative to control) indicated that although hydrophobicity and surface charge both played a role in the adhesion of G. lamblia to solid surfaces, hydrophobicity was more important than surface charge.