Self-assembled monolayers of dendron thiols for electrodeposition of gold nanostructures: toward fabrication of superhydrophobic/superhydrophilic surfaces and pH-responsive surfaces

This paper describes the fabrication of surfaces with different wettability, superhydrophobic/superhydrophilic, and pH-responsive properties. We used a self-assembled monolayer (SAM) of a dendron thiol as the underlying surface for electrodeposition of gold nanostructures. After this modification with a SAM of n-dodecanethiol or 11-mercaptoundecanol, the surface shows remarkable superhydrophobic properties with a contact angle of about 155 degrees and a tilt angle of less than 2 degrees or superhydrophilic properties with a contact angle of about 0 degrees , respectively. Moreover, a large-scale pH-responsive surface was obtained by modification with 2-(11-mercaptoundecanamido)benzoic acid (7) (MUABA). The pH-responsive behavior was amplified by using rough surfaces.     

A transparent and photo-patternable superhydrophobic film

A transparent superhydrophobic TiO2 film, prepared by spin-coating a TiO2 slurry on a glass substrate and modifying the resultant TiO2 film with fluoroalkylsilane molecules, was patterned by illumination with ultraviolet light through a photomask, producing a superhydrophobic/superhydrophilic surface micropattern with very small superhydrophilic areas, which we were able to selectively fill with alginate hydrogel.     

Reversible wettability of a chemical vapor deposition prepared ZnO film between superhydrophobicity and superhydrophilicity

A superhydrophobic ZnO thin film was fabricated by the Au-catalyzed chemical vapor deposition method. The surface of the film exhibits hierarchical structure with nanostructures on sub-microstructures. The water contact angle (CA) was 164.3 degrees, turning into a superhydrophilic one (CA < 5 degrees) after UV illumination, which can be recovered through being placed in the dark or being heated. The film was attached tightly to the substrate, showing good stability and durability. The surface structures were characterized by scanning electron microscopy and atomic force microscopy.     

Fabrication of superhydrophobic cellulose-based materials through a solution-immersion process

An industrial waterproof reagent [(potassium methyl siliconate) (PMS)] was used for fabricating a superhydrophobic surface on a cellulose-based material (cotton fabric or paper) through a solution-immersion method. This method involves a hydrogen bond assembly and a polycondensation process. The silanol, which was formed by a reaction of PMS aqueous solution with CO 2, was assembled on the cellulose molecule surface via hydrogen bond interactions. The polymethylsilsesquioxane coatings were prepared by a polycondensation reaction of the hydroxyl between cellulose and silanol. The superhydrophobic cellulose materials were characterized by FTIR spectroscopy, thermogravimetry, and surface analysis (XPS, FESEM, AFM, and contact angle measurements). Analytical characterization revealed that nanoscale roughness protuberances uniformly covered the surface, thus transforming the cellulose from superhydrophilic to superhydrophobic with a water contact angle of 157 degrees . The superhydrophobic coatings were satisfactory with regard to both chemical and mechanical durability, and because of the transparency of the coatings the native cotton fabric displayed no changes with regard to either morphology or color. The easy availability of the materials and simplicity of this method render it convenient for mass production.     

微图案化钙磷盐膜层的电化学构筑及其生物性能

基于表面分子自组装和光催化转印技术,在TiO2膜层表面获得超亲/超疏水阵列微图案模板,结合电化学沉积技术,成功制备了微图案化钙磷盐膜(CaP)层.扫描电子显微镜(SEM)和电子探针分析(EPMA)结果表明,通过超亲/超疏水阵列微图案模板可构筑高空间分辨的微图案化钙磷盐膜层.微图案化钙磷盐膜层的体外MG-63细胞培养证实,细胞对钙磷盐膜层微单元有强烈的选择性粘附作用,从而可望控制细胞在微单元中的贴壁生长,实现高通量评价细胞行为.     

UVO-tunable superhydrophobic to superhydrophilic wetting transition on biomimetic nanostructured surfaces

A novel strategy for a tunable sigmoidal wetting transition from superhydrophobicity to superhydrophilicity on a continuous nanostructured hybrid film via gradient UV-ozone (UVO) exposure is presented. Along a single wetting gradient surface (40 mm), we could visualize the superhydrophobic (thetaH2O > 165 degrees and low contact angle hysteresis) transition (165 degrees > thetaH2O > 10 degrees ) and superhydrophilic (thetaH2O < 10 degrees within 1 s) regions simply through the optical images of water droplets on the surface. The film is prepared through layer-by-layer assembly of negatively charged silica nanoparticles (11 nm) and positively charged poly(allylamine hydrochloride) with an initial deposition in a fractal manner. The extraordinary wetting transition on chemically modified nanoparticle layered surfaces with submicrometer- to micrometer-scale pores represents a competition between the chemical wettability and hierarchical roughness of surfaces as often occurs in nature (e.g., lotus leaves, insect wings, etc).     

The impact of ultraviolet light on bacterial adhesion to glass and metal oxide-coated surface

Biofouling of glass and quartz surfaces can be reduced when the surface is coated with photocatalytically active metal oxides, such as TiO2 (anatase form) or SnO2. We measured the attachment of eight strains of bacteria to these two metal oxides (TiO2 and SnO2), and to an uncoated glass (control; designated Si-m) before and after exposure to UV light at wavelengths of 254 nm (UVC) or 340 nm UV (UVA). TiO2-coated surfaces were photocatalytically active at both 254 and 340 nm as evidenced by a decrease in the water contact angle of the surface from 59 degrees +/-2 to <5 degrees. The water contact angle of the SnO2 surface was reduced only at 254 nm, while contact angle of the Si-m glass surface was not altered by light of either wavelength. Bacterial adhesion decreased by 10-50% to photocatalyzed glass surfaces. In all cases, bacteria exposed to the UV light were completely killed due to a combination of exposure to UV light and the photocatalytic activity of the glass surfaces. These results show that UV light irradiation of TiO2-coated surfaces can be an effective method of reducing bacterial adhesion.     

Biomimetic superhydrophobic and highly oleophobic cotton textiles

We report a biomimetic procedure to prepare superhydrophobic cotton textiles. By in situ introducing silica particles to cotton fibers to generate a dual-size surface roughness, followed by hydrophobization with polydimethylsiloxane (PDMS), normally hydrophilic cotton has been easily turned superhydrophobic, which exhibits a static water contact angle of 155 degrees for a 10 microL droplet. The roll-off angle of water droplets depends on the droplet volume, ranging from 7 degrees for a droplet of 50 microL to 20 degrees for a 7 microL droplet. When a perfluoroalkyl chain is introduced to the silica particle surface, the superhydrophobic textile also becomes highly oleophobic, as demonstrated by a static contact angle of 140 degrees and a roll-off angle of 24 degrees for a 15 microL sunflower oil droplet.     

Superhydrophilic surface modification of copper surfaces by Layer-by-Layer self-assembly and Liquid Phase Deposition of TiO(2) thin film

A new method has been developed for the superhydrophilic surface modification of copper using versatile solution-based fabrication techniques. The high surface area of TiO(2) nanoparticles was exploited to create a thin film with increased surface energy that transformed copper materials from relatively hydrophobic to superhydrophilic. Copper exposed to ambient conditions resulting in a thin layer of copper oxide has a water contact angle near 90°, but following TiO(2) modification, the contact angle dropped to 0°. The thin film responsible for this drastic improvement in wettability proved durable by retaining its excellent properties throughout an extended application of thermal stress. SEM and Raman Spectroscopic analysis confirmed the structural integrity of the film before and after a durability test.     

Preparation and photocatalytic wettability conversion of TiO2-based superhydrophobic surfaces

We present here a facile method for the preparation of TiO2-based superhydrophobic surfaces. It consists of two steps: (1) roughening of the TiO2 surface with a rf (radio frequency) plasma with CF4 as an etchant and (2) modification of the roughened TiO2 surface with an octadodecylphosphonic acid (ODP) monolayer. Plasma etching caused the thinning of the TiO2 film but at the same time enhanced its surface roughness. A discontinuous wedgelike surface microtexture was formed after etching for 30 s, which, after modification with a monolayer of ODP, showed Cassie-type water super-repellency with a contact angle (CA) hysteresis smaller than 2 degrees . The state of water super-repellency (water CA >165 degrees) could be converted to the state of superhydrophilicity (water CA approximately 0 degrees) by means of ultraviolet (UV) illumination as a result of the photocatalytic decomposition of the ODP monolayer by TiO2. Readsorption of ODP molecules leads directly to the recovery of water super-repellency.     

Study of superhydrophobic electrospun nanocomposite fibers for energy systems

Polystyrene (PS) and polyvinyl chloride (PVC) fibers incorporated into TiO(2) nanoparticles and graphene nanoflakes were fabricated by an electrospinning technique, and then the surface morphology and superhydrophobicity of these electrospun nanocomposite fibers were investigated. Results indicated that the water contact angle of the nanocomposite fiber surfaces increases to 178° on the basis of the fiber diameter, material type, nanoscale inclusion, heat treatment, and surface porosity/roughness. This is a result of the formation of the Cassie-Baxter state in the fibers via the nanoparticle decoration, bead formation, and surface energy of the nanofiber surface. Consequently, these superhydrophobic nanocomposite fibers can be utilized in designing photoelectrodes of dye-sensitized solar cells (DSSCs) as self-cleaning and anti-icing materials for the long-term efficiency of the cells.     

Recoverable and thermally stable superhydrophobic silica coating

A facile route to methyltrimethoxysilane (MTMS) based recoverable superhydrophobic silica coatings with dual-scale roughness obtained through the single step base catalyst sol–gel process. Superhydrophobic silica coatings have shown static water contact angle near about 170 ± 1° and dynamic water contact angle up to 2 ± 1°. Superhydrophobic-superhydrophilic switching feature also achieved by alternating heat treatment and bath surface modification with Trimethylchlorosilane (TMCS) at room temperature (26 °C). Furthermore, the superhydrophobic state could be transformed into superhydrophilic state by slow rate heat treatment. These studies present a very simple strategy for the fabrication of recoverable superhydrophobic surfaces.     

Superhydrophobic perpendicular nanopin film by the bottom-up process

We first fabricated the superhydrophobic film with a water contact angle of 178 degrees based on a perpendicular nanopin fractal structure by a bottom-up process. Until now, only materials with an original water contact angle larger than 90 degrees , which is classified as hydrophobicity, could be used to fabricate the superhydrophobic film (>170 degrees ) according to the possible fractal structure by a top-down process. Now, in this work, a water contact angle of about 178 degrees can be achieved using a lauric acid-coated film with an original contact angle of 75 degrees , which is classified as hydrophilicity, based on an ideal fractal structure for the superhydrophobic surface which is fabricated by the nanosize pin with 6.5 nm diameter.     

Superhydrophilic and superwetting surfaces: definition and mechanisms of control

The term superhydrophobicity was introduced in 1996 to describe water-repellent fractal surfaces, made of a hydrophobic material, on which water drops remain as almost perfect spheres and roll off such surfaces leaving no residue. Today, superhydrophobic surfaces are defined as textured materials (and coatings) on (nonsmooth) surfaces on which water forms contact angles 150° and larger, with only a few degrees of contact angle hysteresis (or sliding angle). The terms superhydrophilicity and superwetting were introduced a few years after the term superhydrophobicity to describe the complete spreading of water or liquid on substrates. The definition of superhydrophilic and superwetting substrates has not been clarified yet, and unrestricted use of these terms sometimes stirs controversy. This Letter briefly reviews the superwetting phenomenon and offers a suggestion on defining superhydrophilic and superwetting substrates and surfaces.     

Electrospun poly(styrene-block-dimethylsiloxane) block copolymer fibers exhibiting superhydrophobicity

Block copolymer poly(styrene-b-dimethylsiloxane) fibers with submicrometer diameters in the range 150-400 nm were produced by electrospinning from solution in tetrahydrofuran and dimethylformamide. Contact angle measurements indicate that the nonwoven fibrous mats are superhydrophobic, with a contact angle of 163 degrees and contact angle hysteresis of 15 degrees . The superhydrophobicity is attributed to the combined effects of surface enrichment in siloxane as revealed by X-ray photoelectron spectroscopy and surface roughness of the electrospun mat itself. Additionally, the fibers are shown by transmission electron microscopy to exhibit microphase-separated internal structures. Calorimetric studies confirm the strong segregation between the polystyrene and poly(dimethylsiloxane) blocks.     

A topography/chemical composition gradient polystyrene surface: toward the investigation of the relationship between surface wettability and surface structure and chemical composition

In this paper, we have prepared of a topography/chemical composition gradient polystyrene (PS) surface, i.e., an orthogonal gradient surface, to investigate the relationship between surface wettability and surface structure and chemical composition. The prepared surface shows a one-dimensional gradient in wettability in the x, y, and diagonal directions, including hydrophobic to hydrophilic, superhydrophobic to hydrophobic, superhydrophobic to superhydrophilic gradients, and so forth. These one-dimensional gradients have different gradient values, gradient range, and contact angle hysteresis, which lie on both the surface roughness and the surface compositions. From the trend of variation of contact angle hysteresis, it can be concluded that the transition from the Cassie's model to the Wenzel's model occurs both by decreasing surface roughness and by increasing surface hydrophilic compositions. Moreover, the transition is more effective via changing surface chemical composition than changing surface roughness herein.     

Smart Titanium Wire Used for the Evaluation of Hydrophobic/Hydrophilic Interaction by In-Tube Solid Phase Microextraction

Evaluation of the hydrophobic/hydrophilic interaction individually between the sorbent and target compounds in sample pretreatment is a big challenge. Herein, a smart titanium substrate with switchable surface wettability was fabricated and selected as the sorbent for the solution. The titanium wires and meshes were fabricated by simple hydrothermal etching and chemical modification so as to construct the superhydrophilic and superhydrophobic surfaces. The micro/nano hierarchical structures of the formed TiO₂ nanoparticles in situ on the surface of Ti substrates exhibited the switchable surface wettability. After UV irradiation for about 15.5 h, the superhydrophobic substrates became superhydrophilic. The morphologies and element composition of the wires were observed by SEM, EDS, and XRD, and their surface wettabilities were measured using the Ti mesh by contact angle goniometer. The pristine hydrophilic wire, the resulting superhydrophilic wire, superhydrophobic wire, and the UV-irradiated superhydrophilic wire were filled into a stainless tube as the sorbent instead of the sample loop of a six-port valve for on-line in-tube solid-phase microextraction. When employed in conjunction with HPLC, four kinds of wires were comparatively applied to extract six estrogens in water samples. The optimal conditions for the preconcentration and separation of target compounds were obtained with a sample volume of 60 mL, an injection rate of 2 mL/min, a desorption time of 2 min, and a mobile phase of acetonile/water (47/53, v/v). The results showed that both the superhydrophilic wire and UV-irradiated wire had the highest extraction efficiency for the polar compounds of estrogens with the enrichment factors in the range of 20–177, while the superhydrophobic wire exhibited the highest extraction efficiency for the non-polar compounds of five polycyclic aromatic hydrocarbons (PAHs). They demonstrated that extraction efficiency was mainly dependent on the surface wettability of the sorbent and the polarity of the target compounds, which was in accordance with the molecular theory of like dissolves like.     

Superamphiphilic Janus fabric

Janus fabrics with superamphiphilicity were fabricated via electrospinning of polyacrylonitrile (PAN). PAN nanofibrous mats were formed on an aluminum foil substrate and then thermally treated to cause hydrolysis. An identical PAN solution was subsequently electrospun onto the hydrolyzed PAN layer, followed by peeling off of the bicomposite film from the collector substrate to produce a free-standing Janus fabric. On one side, the electrospun PAN mat exhibited superhydrophobic properties, with a water contact angle of 151.2°, whereas the initially superhydrophobic PAN sheet on the opposite side of the fabric was converted to a superhydrophilic surface (water contact angle of 0°) through hydrolysis of the surface functional groups induced by the thermal treatment. The resulting Janus fabrics exhibited both superhydrophobicity, repelling water on the one side, and superhydrophilicity, absorbing water on the other side. The organic solvent resistance of the PAN nanofibrous sheets was remarkably improved by incorporation of a tetraethyl orthosilicate. This facile and simple technique introduces a new route for the design and development of functional smart, robust fabrics from an inexpensive, commercially available polymer.     

Controlling the wettability of hierarchically structured thermoplastics

Surfaces play an important role in defining the properties of materials, controlling wetting, adsorption, or desorption of biomolecules, and sealing/bonding of different materials. We have combined microscale features with plasma-etched nanoscale roughness and chemical modification to tailor the wettability of the substrates. Cyclic olefin polymers and copolymers (COPs/COCs) were processed to make a range of surfaces with controlled superhydrophobic or -hydrophilic properties. The hydrophobic properties of the polymers were increased by the introduction of microstructures of varying geometry and spacing through hot embossing. The COC/COP substrates were functionalized by plasma activation in O(2), CF(4), and a mixture of both gases. The plasma etching introduces nanoscale roughness and also chemically modifies the surface, creating either highly hydrophilic or highly hydrophobic (contact angle >150°) surfaces depending on the gas mixture. The influence of geometry and chemistries was characterized by atomic force microscopy, contact angle measurements, and X-ray photoelectron spectroscopy. Measurements of the contact angle and contact angle hysteresis demonstrated long-term stability of the superhydrophobic/superhydrophilic characteristics (>6 months).     

To adjust wetting properties of organic surface by in situ photoreaction of aromatic azide

This article describes development of a simple and convenient method to provide stable low-surface-energy coatings on organic surfaces, by designing and synthesizing a surface-reactive molecule 4-azido-N-dodecylbenzamide, which bears an azide group as the reactive surface anchor and an alkyl chain as the hydrophobic tail. After the hydrophobic modification, rough organic surfaces with contact angle of about 0 degrees can change their surface wetting properties from superhydrophilicity to superhydrophobicity, whose contact angles are above 152 degrees and tilt angles lower than 5 degrees. Moreover, by changing the alkyl chain to a PEO segment, a similar concept can be used to adjust the surface wetting properties from hydrophobic (contact angle approximately 130 degrees) to superhydrophilic (contact angle approximately 0 degrees).