Simultaneous measurement of absolute OH concentration,temperature and flow velocity in a flame by photothermal deflection spectroscopy

We demonstrate the use of photothermal deflection spectroscopy for a simultaneous measurement of absolute minority-species concentration, temperature and flow velocity in a flame from the analysis of a single data trace. The ability to make absolute concentration measurements, as well as the ability to measure three important combustion parameters simultaneously, may make this technique quite useful in many circumstances. Received: 27 August 2002 / Revised version: 26 September 2002 / Published online: 11 December 2002 RID="*" ID="*"Corresponding author. Fax: +1-479/575-4580, E-mail: rgupta@uark.edu     

Influence of temperature and frequency on the electrical parameters of thermally evaporated metal-free phthalocyanine H<Subscript>2</Subscript>Pc thin films

The ac electrical properties of metal-free phthalocyanine (H₂PC) thin films have been studied in the frequency range from 10² to 2×10⁴ Hz and in the temperature range from 150 to 475 K. The ac conductivity σ was found to vary as ω^s with the index s≤1. Although these general values of s appear to be consistent with a hopping process, the present σ values do not increase monotonically with temperature. At low frequency, the capacitance and loss tangent were found to be constant over the entire frequency range, in good qualitative agreement with the equivalent circuit model consisting of an inherent capacitance in parallel with a resistive element. Moreover, at constant frequency, the two parameters increased with increasing temperature up to approximately 300 K. Above this temperature, another sharp decrease in both capacitance and loss tangent was obtained. This type of behavior was interpreted in terms of nomadic (delocalized) polarization, which leads to an increase in the dielectric constant. The drastic decrease of the capacitance and loss tangent observed above room temperature is thought to be related to the decrease in the dielectric constant, which results from the inability of the domains to hold the increases in free charge carrier concentration due to the increase of temperature. Received: 6 December 2001 / Accepted: 7 January 2002 / Published online: 19 July 2002 RID="*" ID="*"Corresponding author. Fax: +972-2/279-6960, E-mail: asaleh@science.alquds.edu     

Field emission from single-walled carbon nanotubes aligned on a gold plate using a self-assembly monolayer

Field emission from single-walled carbon nanotubes (SWNTs) aligned on a patterned gold surface is reported. The SWNT emitters were prepared at room temperature by a self-assembly monolayer technique. SWNTs were cut into sub-micron lengths by sonication in an acidic solution. Cut SWNTs were attached to the gold surface by the reaction between the thiol groups and the gold surface. The field-emission measurements showed that the turn-on field was 4.8 V/μm at an emission current density of 10 μA/cm². The current density was 0.5 mA/cm² at 6.6 V/μm. This approach provides a novel route for fabricating CNT-based field-emission displays. Received: 3 May 2002 / Accepted: 6 May 2002 / Published online: 4 December 2002 RID="*" ID="*"Corresponding author. Fax: +82-54/279-8298, E-mail: ce20047@postech.ac.kr     

Temperature dependence of conductance character in nanotube peapods

Recent electrical transport measurements on metallofullerene-doped nanotube peapods are reviewed. In temperature-dependent conductance measurements, it was found that the temperature plays a crucial role in charge transfer between the nanotube and entrapped metallofullerenes and it is shown that the metallofullerenes can function as electron donors and transfer charge to the carbon nanotube host. The amount of charge transferred varies with temperature. At room temperature, the doped nanotube shows p-type conduction. As the temperature decreases, the conductance becomes n-type and even metallic behavior is observed at still lower temperatures, indicating the degenerate state caused by doping. Received: 4 November 2002 / Accepted: 7 November 2002 / Published online: 10 March 2003 RID="*" ID="*"Corresponding author. E-mail: chiu@fkf.mpg.de     

Influence of velocity in nanoscale friction processes

Force-microscopy images of boric acid crystals were obtained experimentally and simulated with the use of a two-dimensional mechanical model. An analysis of the stick and slip movement of the microscope tip shows that the energy-dissipation mechanism is strongly influenced by the non-linear dynamics of the sliding system. The contributions of stick and viscous forces on the energy dissipation (or friction forces) are studied as a function of the relative scanning velocity. At low relative velocities, the stick forces are shown to be responsible for the energy dissipation. This energy is velocity-dependent, due to the coupling between the two degrees of freedom of the sliding system. As the scanning velocity increases the stick forces are damped; the viscous force is then predominant in the energy-dissipation process. Received: 30 October 2001 / Accepted: 17 May 2002 / Published online: 22 November 2002 RID="*" ID="*"Corresponding author. Fax: +55-21/2295-9397, E-mail: prioli@vdg.fis.puc-rio.br     

Electro-responsive asymmetric nanopores in polyimide with stable ion-current signal

For the preparation of a single asymmetrically shaped nanopore in a polyimide membrane, Kapton foils were irradiated with single heavy ions and subsequently etched from one side in sodium hypochlorite (NaOCl). The other side of the membrane was protected from etching by a stopping medium containing a reducing agent for hypochlorite ions (OCl^-). The resulting conical nanopore rectified ion current and exhibited a stable ion-current flow. Received: 23 May 2002 / Accepted: 2 September 2002 / Published online: 15 January 2003 RID="*" ID="*"Corresponding author. Fax: +49-6159/712-179, E-mail: Z.Siwy@gsi.de     

Tritium recovery from co-deposited layers using 193-nm laser

Recovery of tritium from co-deposited layers formed in deuterium–tritium plasma operations of the TFTR (Tokamak Fusion Test Reactor) was investigated by the use of an ArF excimer laser operating at the wavelength of 193 nm. At the laser energy density of 0.1 J/cm², a transient spike of the tritium-release rate was observed at initial irradiation. Hydrogen isotopes were released in the form of hydrogen-isotope molecules during the laser irradiation in vacuum, suggesting that tritium can be recovered readily from the released gases. In a second experiment, hydrogen (tritium) recovery from the co-deposited layers on JT-60 tiles that had experienced hydrogen-plasma operations was investigated by laser ablation with a focused beam of the excimer laser. The removal rate of the co-deposited layers was quite low when the laser energy density was smaller than the ablation threshold (1.0 J/cm²), but reached 1.1 μm/pulse at the laser energy density of 7.6 J/cm². The effective absorption coefficient in the co-deposited layers at the laser wavelength was determined to be 1.9 μm^-1. The temperature of the surface during the irradiation at the laser energy density of 0.5 J/cm² was measured on the basis of Planck’s law of radiation, and the maximum temperature during the irradiation decreased from 3570 K at the initial irradiation to 2550 K at the 1000th pulse of the irradiation. Received: 5 August 2002 / Accepted: 7 August 2002 / Published online: 28 October 2002 RID="*" ID="*"Corresponding author. Fax: +81-29/2825917, E-mail: shu@tpl.tokai.jaeri.go.jp     

Axial non-uniformity of longitudinal hollow-cathode discharges for laser applications: numerical modeling and comparison with experiments

It is demonstrated by means of numerical modeling that longitudinal hollow-cathode discharges (HCDs) typically used for laser applications are strongly non-uniform in the axial direction. Two kinds of HCDs are investigated; those having one anode ring and those having two anode rings at opposite ends of the HCD tube. The HCD under study was made of copper and operated in a mixture of helium and argon. The calculated potential varied considerably in the axial direction. The densities of the major plasma species showed no maxima in the middle of the HCD, but rather at the anode side(s). The same applied to the sputtering rate at the cathode and the electron-impact ionization and excitation rates in the plasma. The calculation results for both configurations have been compared with measured data, i.e. with the electric current and the optical emission intensities of He (I) and Cu (I) lines as a function of axial position, and reasonable agreement has been reached. Received: 25 June 2002 / Revised version: 29 August 2002 / Published online: 22 November 2002 RID="*" ID="*"Corresponding author. Fax: +32-3/820-23-76, E-mail: annemie.bogaerts@ua.ac.be     

Laser induced decomposition of a designed and a commercial polymer studied by ns-interferometry and shadowgraphy

Commercially available polymers often exhibit quite poor laser ablation properties for irradiation wavelengths around 248 nm. At these wavelengths, the absorption is due to photostable aromatic groups. Photolabile triazene polymers were developed to compare the influence of a photolabile group on the laser ablation process. The photochemically active triazene group has a strong absorption band at 332 nm, whereas the second absorption maximum at 220 nm is due to the photostable aromatic group. By irradiating at 308 nm and 193 nm, the influence of the photochemically active group on the ablation process can be studied. The etching of the triazene polymer starts and ends with the laser pulse. No surface swelling, which is assigned to photothermal ablation, is detected for fluences above the threshold of ablation. The expansion of the laser ablation induced shockwave was measured for the photolabile triazene polymer and the photostable polyimide. The speed of the shockwave increases with fluence and is higher for irradiation with 193 nm than with 308 nm. A shockwave with equal or higher velocity is observed for the triazene polymer compared with polyimide. Received: 28 August 2002 / Accepted: 20 September 2002 / Published online: 28 May 2003 RID="*" ID="*"Corresponding author. Fax: +41-56/310-4412, E-mail: thomas.lippert@psi.ch     

Diffusion of Ta in α-Ti

The diffusion of Ta in the hcp (α) phase of high-purity Ti (99.99%) was studied at different temperatures from 911 K up to 1123 K. The Rutherford Backscattering Spectrometry (RBS) and Heavy Ion RBS (HIRBS) techniques were used to obtain the penetration profiles. The evolution of the diffusion coefficient, D, as a function of temperature follows prediction of the Arrhenius law. The activation energy of the diffusion process is (318±7)kJ/mol, similar to that corresponding to self-diffusion in α-Ti. On the other hand, the measured values of D are systematically lower than those corresponding to self-diffusion by a factor of approximately 5. This reduction could be explained by taking into account the mass difference between Ta and Ti. An increase of the diffusion coefficient was measured when the diffusion proceeds on a less pure Ti (99.9%) matrix. This increment is higher at lower temperatures. Received: 12 November 2001 / Accepted: 12 March 2002 / Published online: 5 July 2002 RID="*" ID="*" RID="*" ID="*" RID="**" ID="**"Corresponding author. Fax: +54-11/6772-7362, E-mail: dyment@cnea.gov.ar RID="*" ID="*"Members of the Carrera del Investigador Científico del Consejo Nacional de Investigaciones Científicas y Técnicas (CONICET), Argentina     

Inhomogeneity of calcium phosphate coatings deposited by laser ablation at high deposition rate

Calcium phosphate coatings were deposited with a KrF excimer laser onto titanium alloy to study their homogeneity. Deposition was performed at a high deposition rate under a water vapour atmosphere of 45 Pa and at a substrate temperature of 575 °C. Samples were also submitted to annealing under the same conditions of deposition for different times just after deposition. The effects of the annealing were also investigated. The morphology of the coatings was studied by scanning electron microscopy. Their structure and phase distribution was analysed by X-ray diffractometry and infrared and micro-Raman spectroscopies. Besides the non-uniform thickness, the results reveal an inhomogeneity in the spatial distribution of calcium phosphate phases in the coatings. The phase distribution can be almost completely correlated with the deposition rate. High deposition rates (0.5 nm/pulse) occurring in the centre of deposition results in the formation of amorphous calcium phosphate, while lower deposition rates favour the presence of hydroxyapatite and alpha tricalcium phosphate. At intermediate deposition rates, beta tricalcium phosphate is found, probably because the superimposed effect of energetic particles bombardment. The annealing process promotes the crystallisation of the amorphous material. The importance of the deposition rate in the phases obtained is stated after comparing these results with a previous work where homogeneous hydroxyapatite coatings were obtained under the same conditions of laser fluence, temperature and pressure, but at lower deposition rates. Received: 22 November 2001 / Accepted: 12 March 2002 / Published online: 5 July 2002 RID="*" ID="*"Corresponding author. Fax: +34-93/402-1138, E-mail: jmfernandez@fao.ub.es     

Time-resolved spectroscopy measurements of a titanium plasma induced by nanosecond and femtosecond lasers

We have studied the plasma induced at the surface of a titanium target following irradiation with femtosecond and nanosecond laser pulses. Time-resolved imaging and spectroscopic measurements allowed us to evidence some features specific to the femtosecond-laser-induced plasma. In this ultrashort interaction regime, we could discriminate between three different velocity populations in the plasma expansion. Coulomb explosion firstly creates highly energetic Ti⁺ ions, which are followed by atomic neutral titanium and lastly by nanoscale titanium oxide clusters. Received: 28 September 2001 / Accepted: 9 July 2002 / Published online: 25 October 2002 RID="*" ID="*"Corresponding author. Fax: +33-1/6931-9996, E-mail: albert@ensta.fr     

Spiral and curved periodic crack patterns in sol-gel films

Thin silicate sol-gel films with four different crack patterns were created reproducibly by controlling the film deposition parameters. The crack geometry, periodicity, and amplitude were studied experimentally as a function of the film thickness, curing time, and temperature. Direct evidence was found that the physical interplay between stress relief through film cracking and stress relief through film warping results in sawtooth, spiral, closed loop, or straight line crack trajectories. Received: 25 March 2002 / Accepted: 1 July 2002 / Published online: 17 December 2002 RID="*" ID="*"Corresponding author. Fax: +1-941-359-4396, Email: sendova@ncf.edu     

100-W average-power, high-energy nanosecond fiber amplifier

We report on the fiber-based amplification of a Q-switched Nd:YAG thin-disk laser. At repetition rates between 3 and 50 kHz output powers up to 100 W are generated. Pulse energies up to 4 mJ, with diffraction-limited beam quality, are generated in a 30-μm Yb-doped large-mode-area fiber, furthermore pulse energies up to 8 mJ are achieved from a multimode fiber amplifier. Received: 8 May 2002 / Revised version: 10 July 2002 / Published online: 25 October 2002 RID="*" ID="*"Corresponding author. Fax: +49-3641/65-7680, E-mail: Jens.Limpert@uni-jena.de     

Dispersion and alignment of carbon nanotubes in polycarbonate

Dispersion and alignment of carbon nanotubes in thermoplastic polymers such as polycarbonate have been studied. Dispersion was accomplished by mixing in a conical twin-screw extruder and alignment was carried out using a fiber-spinning apparatus. The effects of mixing time and fiber draw rates on dispersion and alignment were investigated. Uniform dispersions were produced with relatively short residence times in the extruder. Excellent alignment of carbon nanotubes in nanocomposite filaments was obtained when the fiber draw rate was greater than 70 m/min. The ability to closely control the dispersion and alignment of carbon nanotubes in polymers is expected to lead to the development of nanocomposites with desirable electronic and structural properties. Received: 7 January 2002 / Accepted: 11 April 2002 / Published online: 10 September 2002 RID="*" ID="*"Corresponding author. Fax: +1-508/233-5521, E-mail: Michael.Sennett@natick.army.mil     

Carbon nanotubes formed in graphite after mechanical grinding and thermal annealing

Multi-walled carbon nanotubes with cylindrical and bamboo-type structures are produced in a graphite sample after mechanical milling at ambient temperature and subsequent thermal annealing up to 1400 °C. The ball milling produces a precursor structure and the thermal annealing activates the nanotube growth. Different nanotubular structures indicate different formation mechanisms: multi-wall cylindrical carbon nanotubes are probably formed upon micropores and the bamboo tubes are produced because of the metal catalysts. A two-dimensional growth governed by surface diffusion is believed to be one important factor for the nanotube growth. A potential industrial production method is demonstrated with advantages of large production quantity and low cost. Received: 17 May 2002 / Accepted: 12 September 2002 / Published online: 4 December 2002 RID="*" ID="*"Corresponding author. Fax: +61-2/6125-8338, E-mail: ying.chen@anu.edu.au     

Energy and mass dependence of isotopic enrichment in sputtering

Silver, copper, and boron (from a boron nitride target) were sputtered with xenon ions. The isotopic composition of secondary ions of silver was measured at ion energies ranging from 300 eV to 3 keV and, for copper and boron, at 2.0, 2.5, and 3.0 keV. An ion gun was used to generate the ion beam. The secondary ions were detected at a small emission angle by a quadrupole mass spectrometer. The secondary-ion flux of silver was found to be enriched in heavy isotopes at lower incident-ion energies. The heavy-isotope enrichment was observed to decrease with increasing primary-ion energy. Beyond 500 eV, light isotopes of silver were sputtered preferentially with the enrichment increasing to a constant value of 1.018. The sputtered flux of copper and boron also indicated constant enrichments (1.008 and 1.281 for copper and boron respectively) in light isotopes at high ion energies. Received: 2 August 2002 / Accepted 9 August 2002: / Published online: 4 December 2002 RID="*" ID="*"Present address: Pacific Northwest National Laboratory, Richland, WA 99 352, USA RID="**" ID="**"Present address: Philips Display Components Company, Ottawa, OH 45 875 USA RID="***" ID="***"Corresponding author. Fax: +1-334/727-8090, E-mail: pkray@tusk.edu     

Production of biologically inert Teflon thin layers on the surface of allergenic metal objects by pulsed laser deposition technology

Allergic-type diseases are current nowadays, and they are frequently caused by certain metals. We demonstrated that the metal objects can be covered by Teflon protective thin layers using a pulsed laser deposition procedure. An ArF excimer laser beam was focused onto the surface of pressed PTFE powder pellets; the applied fluences were 7.5–7.7 J/cm². Teflon films were deposited on fourteen-carat gold, silver and titanium plates. The number of ablating pulses was 10000. Post-annealing of the films was carried out in atmospheric air at oven temperatures between 320 and 500 °C. The thickness of the thin layers was around 5 μm. The prepared films were granular without heat treatment or after annealing at a temperature below 340 °C. At 360 °C a crystalline, contiguous, smooth, very compact and pinhole-free thin layer was produced; a melted and re-solidified morphology was observed above 420 °C. The adhesion strength between the Teflon films and the metal substrates was determined. This could exceed 1–4 MPa depending on the treatment temperature. It was proved that the prepared Teflon layers can be suitable for prevention of contact between the human body and allergen metals and so for avoidance of metal allergy. Received: 12 June 2002 / Accepted: 13 June 2002 / Published online: 4 November 2002 RID="*" ID="*"Corresponding author. E-mail: bhopp@physx.u-szeged.hu     

Photofabrication of periodic microstructures in azodye-doped polymers by interference of laser beams

Volume holographic gratings and two-dimensional periodic microstructures in azodye-doped polymethylmethacrylate were fabricated, respectively, by interference of two coherent beams of a femtosecond laser and by interference of three coherent beams of a nanosecond laser. The dependence of the first-order Bragg diffraction efficiency and the photoinduced refractive-index modulation of the gratings on the intensity of the writing light was investigated. The measurements of the absorption spectra before and after irradiation with the writing light suggest that the photoinduced gratings were refractive-index-modulated gratings, which arose from a photoinduced decomposition reaction of the azodye molecules through multiphoton absorption. In the experiments involving the interference of three beams, the period of the two-dimensional periodic microstructures was changed by adjusting the angle between the three writing beams. Received: 10 July 2002 / Revised version: 5 September 2002 / Published online: 20 December 2002 RID="*" ID="*"Corresponding author. Fax: +81-774/955206, E-mail: jhsi@photon.jst.go.jp