Electronic conduction in vitreous semiconductors in the pseudo-binary system (As2S3)1-x(PbS)x

AC conductivity and dielectric relaxation measurements of the bulk amorphous compositions in the pseudo-binary system (As₂S₃)_1-x(PbS)_x (x = 0, 0.1, 0.4 and 0.5) in the frequency range 500 Hz-10 kHz and in the temperature span 180–450 K are reported. The temperature dependence of the ac conductivity, σ_ac(ω), has a broad structure at all frequencies in compositions with x = 0.1, 0.4 and 0.5 whose peak position is not thermally activated. A similar structure was also observed in the data on the dielectric constant, ε₁, which peaked at a frequency of 1 kHz in the composition with x = 0.5. Analysis of the results using the correlated barrier hopping model revealed that the electronic conduction takes place by single polaron and bipolaron hopping processes at high and low temperatures, respectively, in compositions containing Pb. The microstructure and phase-separation in the glasses containing Pb influence the electrical transport and dielectric dispersion. This study has revealed the possible presence of a phase transformation at around 300 K at a frequency of 1 kHz in the dielectric dispersion behaviour of composition with x = 0.5.     

Elastic properties of GexAsySe100−x−y glasses

The elastic properties of Ge_xAs_ySe_100−x−y (0x30; 10y40) glasses have been studied. The results were analyzed in terms of the dependence on the theoretical mean coordination number (mean number of covalent bonds per atom) m (m=2+(2x+y)×0.01). Three ranges of m (2.1m2.51, 2.51<m2.78, 2.78<m3) were revealed, where different dependencies of elastic moduli (Young’s modulus, shear modulus) and Poisson’s ratio of glasses on m were observed.     

Anomalous behavior of excess energy curves of InxGa1−xN grown on GaN and InN

We worked out the excess energies for bulk In_xGa_1−xN and In_xGa_1−xN thin films on GaN and InN in order to investigate their thermodynamic stabilities. It has been found that the excess energy maximum shifted toward x0.80 for InGaN/GaN and x0.10 for InGaN/InN due to the lattice constraint in contrast with x0.50 for bulk. Moreover, it has been revealed that the excess energy for InGaN/GaN is larger than that for bulk at x>0.65. This suggests that In-rich films are less stable on GaN than bulk state. These results indicate that the lattice constraint has a significant influence on thermodynamic stabilities of thin films.     

Compositional dependence of the optical gap in Ge1−xSx, Ge40−xSbxS60 and (As2S3)x(Sb2S3)1−x non-crystalline systems

An attempt is made to calculate the compositional dependence of the optical gap (E_g) in Ge_1−xS_x, Ge_40−xSb_xS₆₀ and (As₂S₃)_x(Sb₂S₃)_1−x non-crystalline systems in an alloy-like approach. From the comparison of both the experimental dependence of E_g and the calculated ones using the Shimakawa relation [E_{g AB} = YE_{g A} + (1−Y)E_{g B}] it is assumed that this equation is useful for such systems or parts of the systems which behave like almost ideal solutions.     

Atomic structure of Al55(Cr1−xMnx)15Si30 metallic glasses observed by neutron diffraction

An atomic structure of Al₅₅(Cr_1−xMn_x)₁₅Si₃₀ (x = 0, 0.49,1) metallic glasses was studied by neutron diffraction. An advantage of the neutron diffraction technique was fully exploited by utilizing the negative scattering length of Mn to form a neutron zero scattering ‘alloy’ for the component Cr_0.51Mn_0.49 in this quaternary Al---(Cr, Mn)---Si alloy. This allows the atomic distribution of the resulting quasibinary Al---Si metallic glass to be derived directly. Moreover, the (Al, Si)---TM (TM = Mn, Cr) and TM---TM pair correlations were also extracted by taking appropriate linear combinations of the atomic structures for the Al₅₅(Cr_1−xMn_x)₁₅Si₃₀ (x = 0, 0.49, 1) metallic glasses. A sharp first peak in the (Al,Si) ---TM pair correlations thus obtained led to the conclusion that a strong attractive interaction exists between (Al, Si) and TM atoms and, hence, that the presence of the TM atoms is responsible for the formation of an amorphous phase.     

Compositional control of CdxZn1−xSe grown by photoassisted organometallic vapor phase epitaxy

The photoassisted OMVPE growth technique is important for the fabrication of blue/green laser diodes based on Cd_xZn_1−xSe quantum wells. Low temperature growth with photoassistance is key to the fabrication of these devices, however, the compositional control of Cd_xZn_1−xSe becomes increasingly difficult as the growth temperature is reduced. We have studied the compositional control of Cd_xZn_1−xSe using the sources DMCd, DMZn, and DMSe, with irradiation from a Hg arc lamp. We studied the dependence of the composition on the growth temperature, irradiation intensity, and source mass flows. The composition x increases with increasing temperature and decreases with increasing irradiation intensity. The solid-phase composition is a non-linear function of the gas-phase composition X. The slope of this characteristic, dx/dX, should be minimized for good compositional control. At 475°C without photoassistance, dx/dX is 1.75 near a composition of 20%, as determined from the data of Parbrook et al. Decreasing the temperature increases dx/dX. At 370°C with 12 mW/cm², dx/dX ≈ 13 and at 350°C with 58 mW/cm² dx/dX ≈ 60. We have investigated this behavior at 370°C with 12 mW/cm² irradiation by studying both the composition and the growth rate as a function of the gas-phase composition. The growth rate is non-monotonic, and is minimum for a gas-phase composition of 0.20. The behavior is quite complex, and is not fully understood at the present time. Nonetheless, our results indicate that the Cd-bearing precursor is adsorbed much more strongly than the Zn-bearing precursor. In addition to this, the introduction of the DMCd strongly inhibits the growth of ZnSe. We have achieved sufficiently good compositional control at 370°C and 12 mW/cm² to grow ZnSe/Cd_xZn_1−xSe/ZnSe multiple quantum well structures. More work is necessary in order to clarify the roles of irradiation intensity and VI/II ratio so that good compositional control can be achieved at lower growth temperatures.     

Cd1−xZnxTe: Growth and characterization of crystals for X-ray and gamma-ray detectors

The choice a suitable crystal growth method and a reasonable x value is of profound importance in the preparation of high quality Cd_1−xZn_xTe crystals for x-ray and gamma-ray detectors. The present paper reviews the evolution and development of Cd_1−xZn_xTe crystal growth for x-ray and gamma-ray detectors. At the same time, emphasis is put upon finding the relationship between the x value and the quality of the Cd_1−xZn_xTe. Three sets of Cd_1−xZn_xTe ingots with different x values, specifically 0.10, 0.15, and 0.20 were grown by the vertical Bridgman method (VBM) and characterized. Their x specification was then correlated with their dislocation densities, Te precipitates, inclusions, IR transmission, resistivities, and impurity concentrations, respectively. It was found that VBM Cd_0.85Zn_0.15Te as grown in this paper possessed the best choice of qualities with respect to defects and impurities.     

High carbon doping of Ga1−xInxAs (x≈0.01) grown by molecular beam epitaxy

We have grown layers of Ga_1−xIn_xAs:C (x ≈ 0.01) on (100) GaAs by molecular beam epitaxy. As C source a graphite filament was used. Structures coherent with the substrate were obtained by adjusting properly the In and C concentrations. With simultaneous incorporation of In and C the strain is compensated and, consequently, the defect density is reduced. A maximum hole concentration value of p = 6×10¹⁹ cm⁻³ was achieved, which is twice higher than the saturation value of C doping of GaAs produced under the same conditions. There is evidence that this value is not in the saturation limit. The product of the hole density times the mobility increases, so the resistance decreases with higher C doping. Raman spectra show that the C_As peak broadens and shifts to lower frequencies for increasing concentration of indium. In H-passivated samples, Raman spectroscopy shows that C_As is surrounded by Ga atoms only. Indium atoms are thus present only in the second group III shell.     

XPS and electroluminescence studies on SrS1−xSex and ZnS1−xSex thin films deposited by atomic layer deposition technique

SrS_1−xSe_x and ZnS_1−xSe_x thin films were deposited by the atomic layer deposition (ALD) technique using elemental selenium as the Se source, thus avoiding use of H₂Se or organometallic selenium compounds. X-ray diffraction (XRD) analysis showed that the films were solid solutions and X-ray photoelectron spectroscopy (XPS) data showed that the surface of both ZnS_1−xSe_x and SrS_1−xSe_x were covered with an oxide and carbon-containing contaminants from exposure to air. The oxidation of SrS_1−xSe_x extended into the film and peak shifts from sulfate were found on the surface. Luminance measurements showed that emission intensity of the ZnS_1−xSe_x:Mn alternating current thin film electroluminescent (ACTFEL) devices at fixed voltage was almost the same as that of the ZnS:Mn device, while emission intensity of the SrS_1−xSe_x:Ce devices decreased markedly as compared to the SrS:Ce device. Emission colors of the devices were altered only slightly due to selenium addition.     

Electronic traps in mixed Si1−xGexO2 films

Thermally stimulated luminescence (TSL) and infrared (IR) spectroscopy were measured in plasma grown Si_1−xGe_xO₂ (x=0, 0.08, 0.15, 0.25, 0.5) with different thicknesses (12–40 nm). A comparison with the TSL properties of thermally grown SiO₂ and GeO₂ was also performed. A main IR absorption structure was detected, due to the superposition of the peaks related to the asymmetric O stretching modes of (i) Si–O–Si (at ≈1060 cm⁻¹) and (ii) Si–O–Ge (at 1001 cm⁻¹). Another peak at ≈860 cm⁻¹ was observed only for Ge concentrations, x>0.15, corresponding to the asymmetric O stretching mode in Ge–O–Ge bonds. A TSL peak was observed at 70°C, and a smaller structure at around 200°C. The 70°C peak was more intense in all Ge rich layers than in plasma grown SiO₂. Based on the thickness dependence of the signal intensity we propose that at Ge concentrations 0.25x0.5 TSL active defects are localised at interfacial regions (oxide/semiconductor, Ge poor/Ge rich internal interface, oxide external surface/atmosphere). Based on similarities between TSL glow curves in plasma grown Si_1−xGe_xO₂, thermally grown GeO₂ and SiO₂ we propose that oxygen vacancy related defects are trapping states in Si_1−xGe_xO₂ and GeO₂.     

Effect of Yb content on purity and crystal growth of Ba2NaNb5O15

Growth by the micro-pulling-down technique (μ-PD) of homogeneous and crack-free fiber single crystals with composition Ba₂Na_1−xYb_xNb₅O₁₅ (0<x<0.08) is reported. The effect of Yb³⁺ addition to barium sodium niobate (BNN, x=0), having the tungsten bronze-type structure, was examined by room temperature X-ray powder diffraction and differential thermal analysis coupled to thermogravimetry. In the region of the monophased field the structure is tetragonal from x=0.02 to 0.16. Volume change is mainly by variation of the a-axis length. Addition of Yb³⁺ to BNN could be effective for the production of high optical quality, crack-free, bulk crystals by the Czochralski technique.     

Low-temperature growth of epitaxial layers of ZnSe1−xTex solid solutions

The layers of ZnSe_1−xTe_x (0 < x < 1.0) solid solutions have been grown by liquid-phase epitaxy in a closed tube at 620–680 °C. Zinc chloride served as a solvent. ZnTe and ZnSe crystals were used as sources and substrates with orienting surfaces (110) and (111) for ZnSe and (110) for ZnTe. The composition of the grown layer was specified by the relative content of the ZnSe and the ZnTe in the solution and was controlled by X-ray analysis. The position of the exciton bands in the photoluminescence spectra of ZnSe_1−xTe_x over the interval 0.3 < x < 1.0 is in agreement with the free exciton energies calculated for these compositions. Relatively low-ohmic (of about 10² Ω cm) epitaxial layers of ZnSe_1−xTe_x solid solutions were grown.     

Growth of Cu(AlxGa1−x)SSe pentenary alloy crystals by iodine chemical vapor transport method

Single crystals of Cu(Al_xGa_1−x)SSe pentenary alloys were successfully grown by the vapor transport technique using iodine as a transport agent. Systematic measurements of the basic crystal properties were carried out using powder X-ray, photoluminescence (PL), photoreflectance (PR), and Van der Pauw methods. Dependence of the lattice constants, exciton transition energies, and PL peak energies on Al composition, x, were examined in detail. The lattice constants obeyed Vegard's law. A quadratic dependence of exciton transition energies on x was found. The broadening parameters in the PR spectrum increase monotonically with increasing x, the results showing that the crystal quality degrades with increasing x. Exciton-related PL peaks were found for 0 ≤ x ≤ 0.77 at 77 K.     

Small-angle X-ray scattering studies of a-Si1−xGex: H alloys

Small-angle X-ray scattering (SAXS) is used to study a-Si:H, a-Ge:H, and a-Si_1−xGe_x: H alloys prepared by plasma-enhanced CVD methods. These amorphous semiconductors show various types of scattering characteristics related to their composition, deposition method, and deposition conditions. For poor quality alloys at low scattering vectors, h, the scattering curve shows an I(h)h⁻² dependence, because of the fractal nature of the inhomogeneities present. Also, a-Ge:H shows these features. Therefore, it is concluded that the inhomogeneities arise principally from clustering of Ge atoms.     

Elastic constant anomaly in Fe80−xMoxB20 metallic glasses

The extensional sound velocities V_E of Fe_80−xMo_xB₂₀(x = 6, 7, 8) metallic glasses have been measured between 100 and 600 K in a saturating magnetic field. Young's modulus (E = _E², = density) shows anomalous temperature dependence at and below the magnetic transition temperature of each glass studied. These anomalies are interpreted as arising from the change of long-range spin coupling energy at the Curie temperature in a molecular field approximation. Comparison is made with similar effects in other crystalline and non-crystalline magnetic materials.     

Laser-induced structural transformation of AsxSe1-x thin amorphous films

The changes in the optical and holographic recording properties of amorphous As_xSe_1-x films with 0 ≤ x ≤ 0.2 under laser irradiation have been measured. The dependence of the transmissivity and diffraction efficiency on the irradiation energy density shows two qualitatively different regions. Below an energy density threshold, E_th, only small changes in the local structure of the system can be detected. In this low-E region, the transmissivity varies reversibly with exposure. Qualitative explanation of the observed behavior may be based on associating such with alteration of deep defect states. Above E_th, the changes were attributed to crystallization transformation. The Raman spectra reveal the progressive transformation of the system from amorphous into the crystalline phase under laser irradiation.     

Effect of Asi on the optical properties of Ga1−xInxAs/InP grown by molecular beam epitaxy

This report focuses on the effect of the As species and the V/III ratio on the optical properties of Ga_1−xIn_xAs/InP grown by molecular beam epitaxy (MBE). The band gap energies of the layers were measured by low temperature photoluminescence (PL) while the indium contents x were determined by X-ray for samples in the investigated range of 0.50<x<0.56. For the analysis of these data we considered the model of Kuo et al. which we confined with a correction for the different measurement temperatures in PL (4.2 K) and X-ray (300 K). Using As₄ with an effective V/III ratio higher than 1.3, we find the best agreement of the band gap energies and predictions of the theory. A lower V/III ratio always implies a reduction of the band gap energy to values 5-15 meV lower than expected. In contrast, using As₂ the PL data fit quite well independent of the effective V/III ratio above unity.     

InxGa1−xAs/GaAs quantum wire structures grown on GaAs (100) patterned substrates with [001] ridges

In_xGa_1−xAs/GaAs (x = 0.12-0.23) quantum well (QW) structures were grown by molecular beam epitaxy (MBE) on [001] ridges with various widths (1.1-12 μm) of patterned GaAs (100) substrate. The smallest lateral width of the InGaAs/GaAs quantum wire (QWR) structures was estimated to be about 0.1 μm by high-resolution scanning electron microscope (SEM). The In contents of the grown InGaAs/GaAs QWs on the ridges were studied as a function of ridge top width (ridge width of the MBE grown layer) by cathodoluminescence (CL) measurements at 78 K. Compared to the InGaAs QW grown on a flat substrate, the In content of the InGaAs/GaAs QW on the ridge increases from 0.22 to 0.23 when the ridge top width decreases to about 2.9 μm, but it decreases steeply from 0.23 down to 0.12 with a further decrease of the ridge width from 2.9 to 0.05 μm. A simulation of MBE growth of InGaAs on the [001] ridges shows that this reduced In content for narrow ridges is due to a large migration of Ga atoms to the (100) ridge top region from {110} side facets.     

X-ray scattering studies of the short and medium range ordering in AsxTe1−x glasses

The structures of As_xTe_1−x(x = 0.2, 0.4, and 0.5) glasses are studied using the differential X-ray anomalous scattering technique. The partial distribution functions have also been obtained for the stoichiometric As₂Te₃ glass, giving information on the medium range ordering. All the glasses show chemical disorder to differing extents, the As₂Te₃ glass being the most disordered. The Te coordination number undergoes a change at x=0.4 where it is 2.5 compared with 2 for AsTe. This change indicates the existence of about 50% of threefold Te sites in the stoichiometric glass, as well as in the Te-rich glasses. Some of the physical properties of the glasses may be explained based on these results.     

Photocurrent measurements on GaAs1−xNx epilayers grown by metalorganic chemical vapor deposition

GaAs_1−xN_x epilayers were grown on a GaAs(0 0 1) substrate by metalorganic chemical vapor deposition. Composition was determined by high resolution X-ray diffraction. Band gap was measured from 77 to 400 K by using photocurrent measurements. The photocurrent spectra show clear near-band-edge peak and their peak energies drastically decrease with increasing nitrogen composition due to band gap bowing in the GaAs_1−xN_x epilayers. Those red shifts were particularly notable for low nitrogen compositions. However, the shifts tended to saturate when the nitrogen composition become higher than 0.98%. When the nitrogen composition is in the range 1.68–3.11%, the measured temperature dependence of the energy band gap was nicely fitted. However, the properties for the nitrogen composition range 0.31–0.98% could not be fitted with a single fitting model. This result indicates that the bowing parameter reaches 25.39 eV for low nitrogen incorporation (x=0.31%), and decreases with increasing nitrogen composition.