Electrochemistry and Electrocatalysis of a Nafion/Nano‐CaCO3/Hb Film Modified Carbon Ionic Liquid Electrode Using BMIMPF6 as Binder

In this paper a room temperature ionic liquid 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆) was used as binder for the construction of carbon ionic liquid electrode (CILE) and a new electrochemical biosensor was developed for determination of H₂O₂ by immobilization of hemoglobin (Hb) in the composite film of Nafion/nano‐CaCO₃ on the surface of CILE. The Hb modified electrode showed a pair of well‐defined, quasi‐reversible redox peaks with E_pa and E_pc as ?0.265 V and ?0.470 V (vs. SCE). The formal potential (E°′) was got by the midpoint of E_pa and E_pc as ?0.368 V, which was the characteristic of Hb Fe(III)/Fe(II) redox couples. The peak to peak separation was 205 mV in pH 7.0 Britton–Robinson (B–R) buffer solution at the scan rate of 100 mV/s. The direct electrochemistry of Hb in the film was carefully investigated and the electrochemical parameters of Hb on the modified electrode were calculated as α=0.487 and k_s=0.128 s^?1. The Nafion/nano‐CaCO₃/Hb film electrode showed good electrocatalysis to the reduction of H₂O₂ in the linear range from 8.0 to 240.0 μmol/L and the detection limit as 5.0 μmol/L (3σ). The apparent Michaelis–Menten constant (K_M^app) was estimated to be 65.7 μmol/L. UV‐vis absorption spectroscopy and FT‐IR spectroscopy showed that Hb in the Nafion/nano‐CaCO₃ composite film could retain its native structure.     

Redox Properties of the Iron Complexes of Orally Active Iron Chelators CP20, CP502, CP509, and ICL670

Redox cycling of iron is a critical aspect of iron toxicity. Reduction of a low‐molecular‐weight iron(III)‐complex followed by oxidation of the iron(II)‐complex by hydrogen peroxide may yield the reactive hydroxyl radical (OH^.) or an oxoiron(IV) species (the Fenton reaction). Complexation of iron by a ligand that shifts the electrode potential of the complex to either to far below ?350 mV (dioxygen/superoxide, pH=7) or to far above +320 mV (H₂O₂/HO^., H₂O pH=7) is essential for limitting Fenton reactivity. The oral chelating agents CP20, CP502, CP509, and ICL670 effectively remove iron from patients suffering from iron overload. We measured the electrode potentials of the iron(III) complexes of these drugs by cyclic voltammetry with a mercury electrode and determined the dependence on concentration, pH, and stoichiometry. The standard electrode potentials measured are ?620 mV, ?600 mV, ?535 mV, and ?535 mV with iron bound to CP20, ICL670, CP502, and CP509, respectively, but, at lower chelator concentrations, electrode potentials are significantly higher.     

Electrochemical Behavior of a Glassy Carbon Electrode Chemically Modified with Nickel Pentacyanonitrosylferrate in Presence of Sulfur Compounds

The glassy carbon electrode was modified with a nickel pentacyanonitrosylferrate film by electrodeposition of Ni and subsequent derivatization with NaPCNF. The film was characterized by XPS and electrochemical methods. Cyclic voltammetry of the NiPCNF onto the GC shows a redox couple (Fe^III/Fe^II) with E°′ of 538 mV (I_pa/I_pc around 1) and ΔE_p of 93 mV in 0.5 mol L^?1 KNO₃, with a diffusion‐controlled process. There was a decrease of anodic peak currents of the film in the presence of sulfide and 2‐propanethiol due to a precipitation reaction on the film surface by nucleophilic attack.     

Atom Transfer Radical Polymerization of Methyl Methacrylate with α,α,α′,α′‐Tetrachloroxylene as an Initiator

The homogeneous ATRP of methyl methacrylate (MMA) using α,α,α′,α′‐tetrachloroxylene (TCX)/CuCl/N,N,N′,N″,N″–pentamethyldiethylenetriamine (PMDETA) as the initiating system has been successfully carried out. The kinetic plots showed first order relationship vs. monomer concentration. Well‐controlled polymerizations with low polydispersities (M_w/M_n=1.15?1.25) polymers have been achieved. The molecular weights increased linearly with monomer conversions and were close to the theoretical values, indicating high initiation efficiency. The polymerization rate increased significantly with an increase of TCX concentration. The rate of polymerization was about 0.6 orders with respect to the concentration of initiator. The polymerization rate increased significantly with an increase of CuCl concentration. The dependence of ln k_p ^app on ln ([CuCl]₀) indicated a 0.91 order. The apparent activation energy was calculated ΔE_app ^≠=43.3 KJ/mol, and the enthalpy of the equilibrium, ΔH_eq ⁰, was estimated to be 21.1 KJ/mol. The structure of obtained PMMA was analyzed by means of ¹H NMR spectroscopy. The result proved that the TCX acted as a bifunctional initiator for ATRP of MMA.     

Voltammetric Studies of Cadmium‐ and Zinc‐Containing Metallothioneins at Nafion‐Coated Mercury Thin Film Electrodes

Voltammetric studies of rabbit liver metallothioneins (MTs, containing both Zn and Cd ions) and Zn₇‐MT were carried out at Nafion‐coated mercury film electrodes (NCMFEs). The accumulation of MT molecules into the NCMFEs enhances the voltammetric signals and the electrostatic interaction between the Nafion membrane and MT facilitates facile electron transfer reactions. Two well‐defined redox waves, with reduction potential (E_pc) values at ?0.740 and ?1.173 V, respectively, were observed. The peak at E_pc =?0.740 V is attributable to the reduction of the Cd‐MT complex, whereas that at E_pc=?1.173 V was assigned to the reduction of the Zn‐MT complex. Zn₇‐MT exhibits only one redox wave with E_pc=?1.198 V. The NCMFE was found to be more advantageous than thin mercury film electrode (MFE), because the pristine metal ions in MTs (e.g., Cd²⁺ and/or Zn²⁺) are not significantly replaced by Hg²⁺. The NCMFE is also complementary to Nafion‐coated bismuth film electrode in that it has a greater hydrogen overpotential, which allows the reduction of the Zn‐MT complex to be clearly observed. Moreover, intermetallic compound formation between Cd and Zn appears to be less serious at NCMFEs. Consequently, the amounts of Cd and Zn deposited into the electrode upon the reduction reactions can be quantified more accurately.     

Atom transfer radical polymerization of n-octyl acrylate under microwave irradiation

The atom transfer radical polymerization (ATRP) of n-octyl acrylate (OA) was successfully carried out using ethyl-2-bromobutyrate as an initiator, and CuBr/2,2^′-bipyridine (bpy) as a catalyst under microwave irradiation (MI) at 76.8 °C. The polymerization of n-octyl acrylate under MI showed linear first-order rate plots, a linear increase of the number-average molecular weight M_n with conversion, and low polydispersities, 1.1<M_w/M_n<1.4, where M_w is weight-average molecular weight. The ATRP of n-octyl acrylate is well controlled. Under the same experimental conditions, the apparent rate constant, k_p^app, under MI is larger apparently than that under conventional heating. In addition, the effects of concentration of catalyst and other factors on polymerization are reported.     

ATRP/OMRP/CCT Interplay in Styrene Polymerization Mediated by Iron(II) Complexes: A DFT Study of the α‐Diimine System

A DFT study of various model systems has addressed the interference of catalytic chain transfer (CCT) as a function of the R² substituent in the atom‐transfer radical polymerization (ATRP) of styrene catalyzed by [FeCl₂(R¹N?C(R²)?C(R²)?NR¹)] complexes. All model systems used R¹=CH₃ in place of the experimental Cy and tBu substituents and 1‐phenylethyl in place of the polystyrene (PS) chain. A mechanistic investigation of 1) ATRP activation, 2) radical trapping in organometallic‐mediated radical polymerization (OMRP), and 3) pathways to the hydride CCT intermediate was conducted with a simplified system with R²=H. This study suggests that CCT could occur by direct hydrogen‐atom transfer without any activation barrier. Further analysis of more realistic models with R²=p‐C₆H₄F or p‐C₆H₄NMe₂ suggests that the electronic effect of the aryl para substituents significantly alters the ATRP activation barrier. Conversely, the hydrogen‐atom‐transfer barrier is essentially unaffected. Thus, the greater ATRP catalytic activity of the p‐NMe₂ system makes the background CCT process less significant. The DFT study also compares the [FeCl₂(R¹N?C(R²)?C(R²)?NR¹)] systems with a diaminobis(phenolato) derivative for which the CCT process shows even greater accessibility but has less incidence because of faster ATRP chain growth and interplay with a more efficient OMRP trapping. The difference between the two systems is attributed to destabilization of the Fe^II catalyst by the geometric constraints of the tetradentate diaminobis(phenolato) ligand.     

Preparation of hydrophobic tannins‐inspired polymer materials via low‐ppm ATRP methods

The novel hydrophobic coating material was received for the first time by a two‐step synthetic route. Firstly, the 15‐functional brominated macroinitiator was prepared by the esterification methodology. Next step covers synthesis of star‐like polymers by poly(n‐butyl acrylate) (PBA) arms polymerization via three low‐ppm atom transfer radical polymerization (ATRP) approaches including application of copper and silver wire in SARA and ARGET ATRP, respectively, as driving forces in redox cycle of catalyst, and an external stimulus in the form of electric current (seATRP) as the third approach in copper(II) regeneration system. As expected, the electrochemically mediated technique allows synthesis of tannic acid‐inspired coating polymers in precisely controlled manner during the entire polymerization process, proved by linear first‐order kinetics plot in contrast to above‐mentioned methods, low dispersity (Ð = 1.18) of star‐shaped polymers, and high efficiency of initiation (? _i = 81%) determined after detaching of polymers side arms. Macromolecules received by all low‐ppm ATRP solutions were characterized by preserved chain‐end functionality (theoretical dead chain fraction; DCF_theo <1%). Adhesive and hydrophobic properties of received polymer materials were investigated by contact angles (θ) and free surface energy (FSE) calculations. Prepared polymer films besides excellent hydrophobic properties have great potential as a self‐healing solution.     

Electrocatalytic reduction of O2 at pyrolytic graphite electrode modified by a novel copper(II) complex with 2-[bis(2-aminoethyl)amino]ethanol and imidazole ligands

A new complex formed by Cu(II) with 2-[bis(2-aminoethyl)amino]ethanol and imidazole is prepared, and its electrochemical properties are studied. The electrochemical experiments are carried out in deaerated pH 7.0 buffer solution through cyclic voltammetry by scanning the potential from 0.1 to −0.5 V with this copper(II) complex-modified electrode as the working electrode. One redox process is observed, which could be assigned to Cu(II)/Cu(I). The formal potential E _0′ = (E _pa + E _pc)/2, where E _pa and E _pc are anodic and cathodic peak potentials, is −248 mV vs. SCE. A straight line, obtained from the plot of I _pc vs. v, indicated a surface-controlled reaction. The modified electrode is very stable and exhibits catalytic activity for oxygen reduction. The possible mechanism for the catalytic reduction of oxygen is studied by cyclic voltammetry and chronoamperometry. The results show that the dioxygen is reduced via a pathway of four-electron reduction to form water. Chronoamperometric measurements show the potentiality of the use of this working electrode as an amperometric sensor for dissolved dioxygen in aqueous media. Published in Russian in Elektrokhimiya, 2006, Vol. 42, No. 8, pp. 975–979. The text was submitted by the authors in English.     

A Hydrogen Peroxide Biosensor Based on Room Temperature Ionic Liquid Functionalized Graphene Modified Carbon Ceramic Electrode

A room temperature ionic liquid (IL) 1‐butyl‐3‐methylimidazolium hexafluorophosphate functionalized graphene (GE) was prepared and a hydrogen peroxide (H₂O₂) biosensor was fabricated by immobilizing hemoglobin (Hb) into the IL‐GE composite film. UV‐visible and Fourier transform infrared spectra of the composite film indicated that Hb retained its native structure in the film. Electrochemical investigation of the biosensor showed a pair of well‐defined, quasi‐reversible redox peaks with E_pa=?0.209 V and E_pc= ?0.302 V (vs. SCE) in pH 7.0 phosphate buffer solution at the scan rate of 100 mV/s. To the reduction of H₂O₂, the biosensor had a good linear range from 8.0×10^?7 to 1.8×10^?4 mol/L with a detection limit of 3.0×10^?7 mol/L. The apparent Michaelis‐Menten constant K^app_M was estimated to be 3.4×10^?5 mol/L.     

Voltammetric Determination of 8‐Nitroquinoline Using a Silver Solid Electrode and Its Application to Model Samples of Drinking and River Water

This work is focused on the application of a silver solid electrode (AgE) for the development of modern voltammetric methods for the determination of submicromolar concentrations of biologically active compounds present in the environment. 8‐Nitroquinoline (8‐NQ), a well‐known chemical carcinogen, was chosen as a model substance. Differential pulse voltammetry (DPV) was used to study electrochemical behavior of 8‐NQ in different aqueous matrices. The following optimal conditions for determination of 8‐NQ in the concentration ranges from 2 to 100 µmol L^?1 were used: Britton? Robinson (BR) buffer of pH 3.0, the regeneration potentials cycles (E_in=?1000 mV, E_fin=?100 mV) and constant cleaning potential ?2000 mV. Practical applicability of AgE for the determination of micromolar concentrations of 8‐NQ was verified on model samples of drinking and river water.     

Effect of Nanoclay on Styrene and Butyl Acrylate AGET ATRP in Miniemulsion: Study of Nucleation Type,Kinetics, and Polymerization Control

Poly(styrene‐co‐butyl acrylate)/clay nanocomposites were synthesized in miniemulsion via activators generated by electron transfer (AGET) for atom transfer radical polymerization (ATRP). Optimum amounts of catalyst and reducing agent were chosen by considering a linear increase in ln([M₀]/[M]) versus time, narrow molecular distribution, and low polydispersity index (PDI). Critical micelle concentration and cross‐sectional surface area per surfactant head group were determined by surface tension analysis. Calculations show that droplet nucleation is the dominant mechanism of nucleation in a miniemulsion system, and there is no micelle in the system. Gel permeation chromatography was used to characterize molecular weight, PDI, and molecular weight distribution. After determination of appropriate conditions, poly(styrene‐co‐butyl acrylate)/clay nanocomposite latexes were synthesized. Low PDI, narrow molecular weights, and first‐order kinetics of the nanocomposites justify that polymerization is well controlled. Kinetics of polymerization decreases by clay loading. The apparent propagation rate constant (k_app) of polymerization in the case of poly(styrene‐co‐butyl acrylate) is 4.079 × 10^?6, which becomes 0.558 × 10^?6 in the case of poly(styrene‐co‐butyl acrylate)/clay nanocomposite with 2% nanoclay. A decrease in the polymerization rate is related to the hindrance effect of nanoclay layers on monomer diffusion toward the loci of growing macroradicals.     

Simple and effective one‐pot synthesis of (meth)acrylic block copolymers through atom transfer radical polymerization

The synthesis of di‐ and triblock copolymers using atom transfer radical polymerization (ATRP) of n‐butyl acrylate (BA) and methyl methacrylate (MMA) is reported. In particular, synthetic procedures that allow for an easy and convenient synthesis of such block copolymers were developed by using CuBr and CuCl salts complexed with linear amines. Polymerizations were successfully conducted where the monomers were added to the reactor in a sequential manner. Poor cross‐propagation between poly(n‐butyl acrylate) (PBA) macroinitiators and MMA was minimized, and therefore control of molecular weights and distributions was realized, by using halogen exchange—a technique involving the addition of CuCl to the MMA during the chain extension of the PBA macroinitiator. High molecular weight (M_n ∼ 90,000) and low polydispersity (M_w /M_n < 1.35) ABA triblock copolymers were also prepared and their structure and properties in bulk have been preliminary characterized indicating the potential of ATRP for the production of all‐acrylic thermoplastic elastomers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2023–2031, 2000     

Copolymerization of methacrylic acid with methyl methacrylate by SET‐LRP

Single‐electron transfer living radical polymerization (SET‐LRP) has developed as a reliable, robust and straight forward method for the construction well‐defined polymers. To span an even larger variety of functional monomers, we investigated the copolymerization of methyl methacrylate with methacrylic acid by SET‐LRP. Copolymerizations were catalyzed by Cu(0)/Me₆‐TREN and performed in MeOH/H₂O mixtures at 50 °C. The SET‐LRP copolymerizations of varying methacrylic acid content were evaluated by kinetic experiments. At low (2.5%) and moderate (10%) MAA loadings, the copolymerizations obeyed perfect first order kinetics (k_p^app = 0.008 min^?1 and k_p^app = 0.006 min^?1) and exhibited a linear increase in molecular weights with conversion providing narrow molecular weight distributions. The SET‐LRP of MMA/25%‐MAA was found to be significantly slower (k_p^app = 0.0035 min^?1). However, a reasonable first‐order kinetics in monomer consumption was maintained, and the control of the polymerization process was preserved since the molecular weight increased linearly with conversion and could therefore be adjusted. This work demonstrates that the copolymerization of methacrylic acid by SET‐LRP is feasible and the design of well‐defined macromolecules comprising acidic functionality can be achieved. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Facile synthesis of AB2‐type miktoarm star polymers through the combination of atom transfer radical polymerization and ring‐opening polymerization

A novel miktofunctional initiator ( 1 ), 2‐hydroxyethyl 3‐[(2‐bromopropanoyl)oxy]‐2‐{[(2‐bromopropanoyl)oxy]methyl}‐2‐methyl‐propanoate, possessing one initiating site for ring‐opening polymerization (ROP) and two initiating sites for atom transfer radical polymerization (ATRP), was synthesized in a three‐step reaction sequence. This initiator was first used in the ROP of ?‐caprolactone, and this led to a corresponding polymer with secondary bromide end groups. The obtained poly(?‐caprolactone) (PCL) was then used as a macroinitiator for the ATRP of tert‐butyl acrylate or methyl methacrylate, and this resulted in AB₂‐type PCL–[poly(tert‐butyl acrylate)]₂ or PCL–[poly(methyl methacrylate)]₂ miktoarm star polymers with controlled molecular weights and low polydispersities (weight‐average molecular weight/number‐average molecular weight < 1.23) via the ROP–ATRP sequence. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2313–2320, 2004     

Synthesis of amphiphilic copolymer brushes: Poly(ethylene oxide)‐graft‐polystyrene

A well‐defined amphiphilic copolymer brush with poly(ethylene oxide) as the main chain and polystyrene as the side chain was successfully prepared by a combination of anionic polymerization and atom transfer radical polymerization (ATRP). The glycidol was first protected by ethyl vinyl ether to form 2,3‐epoxypropyl‐1‐ethoxyethyl ether and then copolymerized with ethylene oxide by the initiation of a mixture of diphenylmethylpotassium and triethylene glycol to give the well‐defined polymer poly(ethylene oxide‐co‐2,3‐epoxypropyl‐1‐ethoxyethyl ether); the latter was hydrolyzed under acidic conditions, and then the recovered copolymer of ethylene oxide and glycidol {poly(ethylene oxide‐co‐glycidol) [poly(EO‐co‐Gly)]} with multiple pending hydroxymethyl groups was esterified with 2‐bromoisobutyryl bromide to produce the macro‐ATRP initiator [poly(EO‐co‐Gly)_(ATRP). The latter was used to initiate the polymerization of styrene to form the amphiphilic copolymer brushes. The object products and intermediates were characterized with ¹H NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, Fourier transform infrared, and size exclusion chromatography in detail. In all cases, the molecular weight distribution of the copolymer brushes was rather narrow (weight‐average molecular weight/number‐average molecular weight < 1.2), and the linear dependence of ln[M₀]/[M] (where [M₀] is the initial monomer concentration and [M] is the monomer concentration at a certain time) on time demonstrated that the styrene polymerization was well controlled. This method has universal significance for the preparation of copolymer brushes with hydrophilic poly(ethylene oxide) as the main chain. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4361–4371, 2006     

Model Reduction in Emulsion Polymerization Using Hybrid First Principles/Artificial Neural Networks Models, 2

Summary: A “series” hybrid model based on material balances and artificial neural networks to predict the evolution of weight average molecular weight, , in semicontinuous emulsion polymerization with long chain branching kinetics is presented. The core of the model is composed by two artificial neural networks (ANNs) that calculate polymerization rate, R_p, and instantaneous weight‐average molecular weight, from reactor process variables. The subsequent integration of the material balances allowed to obtain the time evolution of conversion and , along the polymerization process. The accuracy of the proposed model under a wide range of conditions was assessed. The low computer‐time load makes the hybrid model suitable for optimization strategies.

Effect of the monomer feed rate on .     

Cu(II)‐Mediated Atom Transfer Radical Polymerization of Methyl Methacrylate via a Strategy of Thermo‐Regulated Phase‐Separable Catalysis in a Liquid/Liquid Biphasic System: Homogeneous Catalysis,Facile Heterogeneous Separation,and Recycling

A strategy of thermo‐regulated phase‐separable catalysis (TPSC) is applied to the Cu(II)‐mediated atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in a p‐xylene/PEG‐200 biphasic system. Initiators for continuous activator regeneration ATRP (ICAR ATRP) are used to establish the TPSC‐based ICAR ATRP system using water‐soluble TPMA as a ligand, EBPA as an initiator, CuBr₂ as a catalyst, and AIBN as a reducing agent. By heating to 70 °C, unlimited miscibility of both solvents is achieved and the polymerization can be carried out under homogeneous conditions; then on cooling to 25 °C, the mixture separates into two phases again. As a result, the catalyst complex remains in the PEG‐200 phase while the obtained polymers stay in the p‐xylene phase. The catalyst can therefore be removed from the resultant polymers by easily separating the two different layers and can be reused again. It is important that well‐defined PMMA with a controlled molecular weight and narrow molecular weight distribution could be obtained using this TPSC‐based ICAR ATRP system.

     

Novel superhydrophobic silica/poly(siloxane‐fluoroacrylate) hybrid nanoparticles prepared via surface‐initiated ATRP and their surface properties: The effects of polymerization conditions

A series of superhydrophobic poly(methacryloxypropyltrimethoxysilane, MPTS‐b‐2,‐2,3,3,4,4,4‐heptafluorobutyl methacrylate, HFBMA)‐grafted silica hybrid nanoparticles (SiO₂/PMPTS‐b‐PHFBMA) were prepared by two‐step surface‐initiated atom transfer radical polymerization (SI‐ATRP). Under the adopted polymerization conditions in our previous work, the superhydrophobic property was found to depend on the SI‐ATRP conditions of HFBMA. As a series of work, in this present study, the effects of polymerization conditions, such as the initiator concentration, the molar ratio of monomer and initiator, and the polymerization temperature on the SI‐ATRP kinetics and the interrelation between the kinetics and the surface properties of the nanoparticles were investigated. The results showed that the SI‐ATRP of HFBMA was well controlled. The results also showed that both the surface microphase separation and roughness of the hybrid nanoparticles could be strengthened with the increase of the molecular weight of polymer‐grafted silica hybrid nanoparticles. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

An efficient way to tune grafting density of well‐defined copolymers via an unusual Br‐containing acrylate monomer

A series of well‐defined amphiphilic graft copolymers, containing hydrophilic poly(acrylic acid) backbone and hydrophobic poly(butyl acrylate) side chains, were synthesized by sequential reversible addition fragmentation chain transfer (RAFT) polymerization and atom transfer radical polymerization (ATRP) without any postpolymerization functionality modification followed by selective acidic hydrolysis of poly(tert‐butyl acrylate) backbone. tert‐Butyl 2‐((2‐bromopropanoyloxy)methyl)‐acrylate was first homopolymerized or copolymerized with tert‐butyl acrylate by RAFT in a controlled way to give ATRP‐initiation‐group‐containing homopolymers and copolymers with narrow molecular weight distributions (M_w/M_n < 1.20) and their reactivity ratios were determined by Fineman‐Ross and Kelen‐Tudos methods, respectively. The density of ATRP initiation group can be regulated by the feed ratio of the comonomers. Next, ATRP of butyl acrylate was directly initiated by these macroinitiators to synthesize well‐defined poly(tert‐butyl acrylate)‐g‐poly(butyl acrylate) graft copolymers with controlled grafting densities via the grafting‐from strategy. PtBA‐based backbone was selectively hydrolyzed in acidic environment without affecting PBA side chains to provide poly(acrylic acid)‐g‐poly(butyl acrylate) amphiphilic graft copolymers. Fluorescence probe technique was used to determine the critical micelle concentrations in aqueous media and micellar morphologies are found to be spheres visualized by TEM. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2622–2630, 2010