Determination of Selenium(IV) by Stripping Voltammetry at a Mercury-Film Electrode

A procedure was proposed for the determination of selenium(IV) by stripping voltammetry on a mercury-film electrode at an electrolysis potential of +0.4 V versus the saturated silver–silver chloride reference electrode in a 1 M H₂SO₄ solution. The current of the cathodic peak is a linear function of the selenium(IV) concentration in the range from 5 × 10^–3 to 3 × 10^–1 mg/L (6.3 × 10^–8 to 3.8 × 10^–6 M) at a time of electrolysis of 30 s (t _el). The detection limit for selenium is 1 × 10^–4 mg/L (1.3 × 10^–9 M) at t _el = 300 s. It was shown that selenium(IV) can be determined in the presence of 10 mg/L Zn(II), 1 mg/L Cd(II), 0.5 mg/L Pb(II), and 0.2 mg/L Cu(II). A procedure for the determination of selenium in natural, mineral, and potable water was proposed.     

Synthesis and Electrochemical Studies of Ruthenium(II) Dicarbonyl Bis(ferrocenyl-β-diketonates)

The reaction of [Ru₃(CO)₁₂] ( 1 ) with six equiv. of FcC(O)CH₂C(O)R ( 2a , R = Me; 2b , R = Fc; Fc = Fe(η⁵-C₅H₄)(η⁵-C₅H₅)) produced the Ru^II compounds [Ru(CO)₂(FcC(O)CHC(O)R)₂] ( 3a , R = Me; 3b , R = Fc) in moderate yields. IR studies and single-crystal X-ray analysis ( 3a ) confirmed that the CO ligands are cis-oriented and that the respective β-diketonates O,O'-chelate-bonded setting-up an octahedral surrounding at Ru^II. Electrochemical (cyclic and square-wave voltammetry) and spectroelectrochemical (UV/Vis-NIR, IR) measurements were additionally carried out. Compounds 3a , b display two ( 3a : E₁^o' = 140; E₂^o' = 255 mV; ΔE^o' = 115 mV for [ 3a ]⁺/[ 3a ]²⁺) or four ( 3b : E₁^o' = 80 mV, E₂^o' 190 mV (ΔE^o' = 110 mV, [ 3b ]⁺/[ 3b ]²⁺), E₃^o' = 355 mV (ΔE^o' = 165 mV, [ 3b ]²⁺/[ 3b ]³⁺), E₄^o' = 490 mV (ΔE^o' = 135 mV, [ 3b ]³⁺/[ 3b ]⁴⁺)) electrochemical reversible one-electron redox processes indicating electrostatic interactions among the ferrocenyl groups as oxidation progresses, which was confirmed by UV/Vis-NIR and in situ IR spectroscopy. One ferrocenyl group on each β-diketonate ligand is by this means 1^st oxidized before the 2^nd ferrocenyl group of the same β-diketonate building block follows.     

Calorimetric determination enthalpy of the formation of natural pyromorphite

A calorimetric study of natural pyromorphite Pb₅[PO₄]₃Cl was performed. Its enthalpy of formation was determined by melt solution calorimetry from elements Δ_f H _el^∘(298.15 K) = −4124 ± 20 kJ/mol. Value Δ_f G _el^o(298.15 K) = −3765 ± 20 kJ/mol was calculated.     

Ferrocenyl-Pyrenes,Ferrocenyl-9,10-Phenanthrenediones,and Ferrocenyl-9,10-Dimethoxyphenanthrenes: Charge-Transfer Studies and SWCNT Functionalization

The synthesis of 1-Fc- ( 3 ), 1-Br-6-Fc- ( 5 a ), 2-Br-7-Fc- ( 7 a ), 1,6-Fc₂- ( 5 b ), 2,7-Fc₂-pyrene ( 7 b ), 3,6-Fc₂-9,10-phenanthrenedione ( 10 ), and 3,6-Fc₂-9,10-dimethoxyphenanthrene ( 12 ; Fc=Fe(η⁵-C₅H₄)(η⁵-C₅H₅)) is discussed. Of these compounds, 10 and 12 form 1D or 2D coordination polymers in the solid state. (Spectro)Electrochemical studies confirmed reversible Fc/Fc⁺ redox events between −130 and 160 mV. 1,6- and 2,7-Substitution in 5 a (E°′=−130 mV) and 7 a (E°′=50 mV) influences the redox potentials, whereas the ones of 5 b and 7 b (E°′=20 mV) are independent. Compounds 5 b , 7 b , 10 , and 12 show single Fc oxidation processes with redox splittings between 70 and 100 mV. UV/Vis/NIR spectroelectrochemistry confirmed a weak electron transfer between Fe^II/Fe^III in mixed-valent [ 5 b ]⁺ and [ 12 ]⁺. DFT calculations showed that 5 b non-covalently interacts with the single-walled carbon nanotube (SWCNT) sidewalls as proven by, for example, disentangling experiments. In addition, CV studies of the as-obtained dispersions confirmed exohedral attachment of 5 b at the SWCNTs.     

Effect of the Peptidic Scaffold in Copper(II) Coordination and the Redox Properties of Short Histidine‐Containing Peptides

A linear decapeptide containing three His and one Asp residues and a β‐turn‐inducing dProPro unit was synthesised. A detailed potentiometric, mass spectrometric and spectroscopic study showed that at a 1:1 ratio of C_Cu/C_peptide this peptide formed a major [CuH(O_dPro?Asp)]²⁺ species (pH range 5.5–7.0), in which the Cu²⁺ ion was bound to the His and Asp residues in square‐planar or square‐pyramidal geometries. The stability constant corrected for protonated species (log K*=9.33) is almost equal to the value obtained for the parent [CuH(O?Asp)]²⁺ species (log K*_CuH(O‐Asp)=9.28), but lower than that obtained for the cyclic [CuH(C?Asp)]²⁺ complex (log K*_CuH(C‐Asp)=10.79) previously published. Thus, the replacement of the ProGly unit by the stronger β‐turn‐inducing dProPro unit did not generate a more stable copper(II) species, although the O_dPro?Asp peptide was structured in solution, as shown by circular dichroism (CD) spectroscopy. Interestingly, the calculated value of K_eff showed that this peptide behaved similarly to the O?Asp or C?Asp counterparts, depending on the pH value. The cyclic voltammetry data indicated that the most easily reducible species were [CuH(O?Asp)]²⁺ (E′⁰=262 mV versus a normal hydrogen electrode (NHE)) and [CuH(O_dPro?Asp)]²⁺ (E′⁰=294 mV versus NHE) complexes, the peptidic scaffolds of which are open. A lower value was obtained for [CuH(C?Asp)]²⁺ (E′⁰=24 mV versus NHE). A different degree of non‐reversibility was observed for the three copper(II) complexes; this could reflect a different degree of flexibility in their respective peptidic scaffolds.     

Synthesis and Structural Studies of 2-(hydroxyimino)-1-methylpropylideneamino-phenyliminobutan-2-one Oxime, Ligand and its Complexes with Cu(II) and Ni(II)

A new ligand incorporating a dioxime moiety, (2E,3E)-3-[(2-{[(1E,2E)-2-(hydroxyimino)-1-methylpropylidene]amino}phenyl)imino]butan-2-one oxime, (H₂Phmdo) (3) has been prepared by reacting 2,3-butanedionemono-{O-[4-(1-methyl-2-oxo-propylideneaminooxy)-2,3-bis-(1-methyl-2-oxo-propylideneaminooxy-methyl)-but-2-enyl]-oxime} (2) with 1,2-phenylenediamine. Mono-, di- and trinuclear copper(II) and/or nickel(II) complexes of H₂Phmdo were characterized by elemental analyses, magnetic moments, ¹H-n.m.r. and ¹³C-n.m.r., i.r. and mass spectral studies. The mononuclear copper(II) and nickel(II) complexes of H₂Phmdo were found to have a 1:1 metal:ligand ratio. Elemental analyses, stoichiometric and spectroscopic data of the metal complexes indicated that the metal ions are coordinated to the oxime and imine nitrogen atoms (C=N). In the dinuclear complexes, in which the first Cu^(II) or Ni^(II) ion was complexed with nitrogen atoms of the oxime and imine groups, the second Cu^(II) ion is ligated with dianionic oxygen atoms of the oxime groups and are linked to the 1,10-phenanthroline nitrogen atoms. The data support the proposed structure of H₂Phmdo and its complexes.     

Synthesis and structural studies of (2E,3E)-3-[(6-{[(1E,2E)-2-(hydroxyimino)-1-methylpropylidene]amino}pyridin-2-yl)imino]butan-2-one oxime, ligand and its mono-, di- and trinuclear copper(II) complexes

A new dioxime ligand, (2E,3E)-3-[(6-{[(1E,2E)-2-(hydroxyimino)-1-methylpropylidene]amino}-pyridin-2-yl)imino]butan-2-one oxime, (H₂Pymdo) (3) has been synthesized in H₂O by reacting 2,3-butenedione monoxime (2) with 2,6-diaminopyridine. Mono-, di- and tri-nuclear copper(II) complexes of the dioxime ligand (H₂Pymdo) and/or 1,10-phenanthroline have been prepared. The dioxime ligand (H₂Pymdo) and its copper(II) complexes were characterized by ¹H-n.m.r., ¹³C-n.m.r. and elemental analyses, magnetic moments, i.r. and mass spectral studies. The mononuclear copper(II) complex of H₂Pymdo was found to have a 1:1 metal:ligand ratio. Elemental analyses, stoichiometric and spectroscopic data of the metal complexes indicated that the metal ions are coordinated to the oxime and imine nitrogen atoms (C=N). In the dinuclear complexes, in which the first Cu(II) ion was complexed with nitrogen atoms of the oxime and imine groups, the second Cu(II) ion is ligated with dianionic oxygen atoms of the oxime groups and are linked to the 1,10-phenanthroline nitrogen atoms. The trinuclear copper(II) complex (6) was formed by coordination of the third Cu(II) ion with dianionic oxygen atoms of each of two molecules of the mononuclear copper(II) complexes. The data support the proposed structure of H₂Pymdo and its Cu(II) complexes.     

Anodic Stripping Potentiometric Determination of Cu,Pb, Cd and Zn In Natural Waters on a Novel Combined Electrode System

Abstract

A method is described for the reliable determination of copper, lead, cadmium and zinc in natural waters by anodic stripping potentiometry with the use of a novel combined electrode. The method involves two stripping cycles during which copper is initially determined on its own, followed by simultaneous determination of lead, cadmium and zinc after addition of gallium (III) ions. The optimum conditions include 0.01 M HCl as supporting electrolyte, 10 mg/L Hg (II) as chemical oxidant; E_dep(Cu) -700 mV vs Ag/AgCl; E_{dep(Pb,Cd,Zn)} -1200 mV vs Ag/AgCl; t_dep 10s; 150 μg/L Ga (III); sample rotation rate 5 and rest period 30s. Under these conditions, as low as 0.06 μg/L Cu (0.7% RSD); 0.2 μg/L Pb (13% RSD); 0.04 μg/L Cd (7.8% RSD) and 0.06 μg/L Zn (5.5% RSD) can be determined reliably. A linear concentration range of 0–110 μg/L was obtained for the four metals. The successful application of the method to reference fresh water, creek water and tap water is demonstrated.     

Synthesis,Structure, and Characterization of [FeIIILCl3] (L = 1, 4, 8‐Triazacycloundecane, 1, 4, 7‐Triazacyclononane)

The structures of [Fe^III(tacud)Cl₃] ( 1 ) and [Fe^III(tacn)Cl₃] ( 2 ) (tacud = 1, 4, 8‐triazacycloundecane, tacn = 1, 4, 7‐triazacyclononane) are reported. Both compounds crystallize in the orthorhombic space group Pnma with a = 12.5570(9), b = 12.0028(9), c = 8.2577(6) Å, V = 1244.59(16) ų, and Z = 4 for 1 and a = 12.095(4), b = 11.125(4), c = 7.963(3) Å, V = 1071.5(6) ų, and Z = 4 for 2 . The structures of 1 and 2 feature iron(III) in distorted octahedral arrangement with three facially coordinated nitrogen ligands and three chlorides. Bidirectional intermolecular hydrogen bonding between N–H groups and coordinated chlorides is seen for 1 and 2 . Compound 1 is the first example of iron(III) bonded to tacud and compound 2 is only the second structure reported of a 1:1 complex between iron and tacn. The Fe^3+/2+ redox couple for 1 is observed at E_1/2 = 0.25 V (ΔE_p = 99 mV), and for 2 at E_1/2 = 0.09 V (ΔE_p = 108 mV) versus NHE in DMF at 298 K. Comparison of structural, magnetic, and electrochemical properties for 1 and 2 reveal subtle differences consistent with the stronger coordinating properties of tacn relative to tacud.     

Correlation Between Polarographic Half-Wave Potentials and Electronic Spectra of Cis-Trans Complexes of Chromium (III) and Rhodium (III)

A linear correlation between half-wave potential (E^1/2) for the process M(III)→M(II) and the first d-d transition band (v) of the types cis and trans-[M(en)₂X₂]ⁿ⁺ (M=Cr(III) and Rh(III), X=ONO^?, NCS^?, F^?, Cl^?, Br^?, I^?, H₂O, DMF, DMSO, n=1, 3) was found. The plots of the difference in half-wave potential (ΔE_1/2) against the difference in the first d-d transition hand (Δv) for the cis and trans isomer are straight lines. The equations, E_1/2=β/nαF+K₁ and ΔE_1/2=(β/NαF)Δ were derived, and used to describe the linear correlations between polarographic behavior and electronic spectrum.     

Synthesis of All Four Stereoisomers of (E)-Vitamin KT (Phylloquinone), Analysis of Their Diastereoisomeric and Enantiomeric Purities and Determination of Their Biopotencies

All four stereoisomers of (E)-vitamin Kb i. e. (2¹E, ⁷R, 11¹R)-l (= 1a), (2¹E, 7¹ R, l1¹S)-1 (= 1b), (2¹E, 7¹ S, 11¹S) 1 ( = 1c), and (2¹E, 7¹S, 11¹R)-l ( = Id), have been synthesized in a state of high chemical and stereoisomeric purity. The synthesis of stereoisomers lb-d relied on the use of the optically active Cf¹* and C*¹⁰-building blocks (R)- or (S)-4-(benzyloxy)-3-methylbutanal ((R)- or (S)-2) and (R)- or (S)-citronellal ((R)- or (S)- 3 ) which had been secured by the Rh¹-catalyzed allylamine-to-enamine isomerization technology. For the synthesis of the natural (E)-vitamin-K1 stereoisomer 1a , a new route starting from natural phylol was developed, based on an O-alkylation/rearrangement procedure. A HPLC method was developed which separates with remarkable efficiency all four stereoisomers of (E)- as well as three out of the four stereoisomers of (Z)-vitamin K¹ on optically active poly(trityl methacrylate) as the chiral stationary phase supported on Nucleosil. By this method, the stereoisomeric content of the stereoisomers 1b-d synthesized was shown to be in the range of 96-98 %, while the natural isomer 1a was configurationally uniform. The biological activity of the four (E)-vitamin-K₁ stereoisomers was determined by means of the curative prothrombin time test with vitamin-K-depleted chicks. A high precision of the results was obtained with the recently introduced up-and-down organization of the test and the statistical evaluation according to an estimation procedure. With the natural (E)-vitamin-K₁ stereoisomer 1a as standard (set at 1. 0), activities of 0. 93, 1. 19, and 0. 99 were found for stereoisomers 1b, 1c , and 1d , respectively. Within the confidence limits, these activity ratios can be regarded as identical, A very similar efficacy was obtained by comparison of (E, all-rac )-vitamin K₁ ((2¹E, RS, 11′ RS)- 1 ; equimolar mixture of the four stereoisomers 1a-d) with the natural (E)-vitamin-K₁ stereoisomer 1a ). A synergistic effect was not detectable, as was the case with the eight α-tocopheryl-acetate stereoisomers.     

Adsorptive Stripping Square-Wave Voltammetry of Creatine

ABSTRACT

An adsorptive stripping square-wave voltammetric method for quantitative determination of creatine is developed. The basic redox properties of creatine are investigated by means of square-wave and cyclic staircase voltammetry. Creatine undergoes an irreversible reduction in neutral and acidic medium at a hanging mercury drop electrode. The square-wave voltammetric response of creatine depends on the parameters of the SW excitation signal as well as on the concentration and type of the supporting electrolyte, the accumulation time and the potential and pH of the medium. The optimal experimental conditions for quantitative determination of creatine are as follows: supporting electrolyte 0.1 mol/L KNO₃ buffered with 0.1 mol/L acetate buffer to pH = 4 and accumulation potential -1.2 V. The optimal SW parameters found are: frequency f = 120 Hz, amplitude E _sw = 30 mV, and scan increment dE = 4 mV. A detection limit of 6.6 x 10^?8 mol/L creatine was obtained after 30 s preconcentration period at accumulation potential -1.2 V. The correlation coefficients of the calibration curves at concentration levels of 10^?7 to 10^?5 mol/L creatine are greater than 0.99. The results of recovery tests range from 92.18% to 102.51%.     

Synthesis and Structural Studies of 2,2′-[(2E,5E)-hexane-2,5-diylidenedi-nitrilo]-dibenzenethiol and 2-Hydroxybenzaldehyde (2E,5E)-hexane-2,5-diylidenehydrazone ligands and their Mononuclear Cu(II) and Ni(II) Complexes

Monomeric copper(II) and nickel(II) complexes with tetradentate two new ligands, 2,2′-[(2E,5E)-hexane-2,5-diylidenedi- nitrilo]dibenzenethiol(H₂L) and 2-hydroxybenzaldehyde (2E,5E)-hexane-2,5-diylidenehydrazone(H₂L¹) have been synthesized and characterized by elemental analyses, magnetic moments, molar conductance, ¹H-NMR and ¹³C-NMR, IR, mass spectral studies, theoretical calculations (MM2 and AM1) molecular methods. The mononuclear metal complexes of H₂L and (H₂L¹) were found to have a 1:1 metal:ligand ratio. Elemental analyses, stoichiometric and spectroscopic data of metal complexes indicated that the metal ions were coordinated to the sulphur (-SH) and/or (-OH) oxygen and imine nitrogen atoms (C = N). All of the data obtained from spectral, and molecular mechanics (MM2) or semi empirical calculations (AM1) studies support the structural properties of ligands and its Cu(II) and Ni(II) metal complexes.     

Formation of polymeric chain assemblies of transition metal complexes with a multidentate Schiff-base

The new multidentate Schiff-base (E)-6,6′-((1E,1′E)-(ethane-1,2-diylbis(azan-1-yl-1-ylidene))bis(methan-1-yl-ylidene))bis(4-methyl-2-((E)(pyridine-2-ylmethylimino)methyl)phenol) H₂L and its polymeric binuclear metal complexes with Cr(III), Mn(II), Fe(II), Co(II), Ni(II), Cu(II), Zn(II), Cd(II) and Hg(II) are reported. The reaction of 2,6-diformyl-4-methyl-phenol with ethylenediamine in mole ratios of 2:1 gave the precursor 3,3′-(1E,1′E)-(ethane-1,2-diylbis(azan-1-yl-1ylidene))bis(methan-1-yl-1-ylidene)bis(2-hydroxy-5-methylbenzaldehyde) W. Condensation of the precursor with 2-(amino-methyl)pyridine in mole ratios of 1:2 gave the new N₆O₂ multidentate Schiff-base ligand H₂L. Upon complex formation, the ligand behaves as a dibasic octadentate species with the involvement of the nitrogen atoms of the pyridine groups in coordination for all complexes. The mode of bonding and overall geometry of the complexes were determined through physico-chemical and spectroscopic methods. These studies revealed octahedral geometries for Cr(III), Mn(II), Fe(II), Co(II), Ni(II), Cu(II), Cd(II) and Hg(II) complexes of general formulae [Cr₂^III(L)Cl₂]Cl₂, [Ni₂^II(L)(H₂O)₂]Cl₂ and [M₂(L)Cl₂] and five co-ordinate Zn(II) complex of general formula [Zn₂^II(L)]Cl₂.     

Electrochemistry and Electrocatalysis of a Nafion/Nano‐CaCO3/Hb Film Modified Carbon Ionic Liquid Electrode Using BMIMPF6 as Binder

In this paper a room temperature ionic liquid 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆) was used as binder for the construction of carbon ionic liquid electrode (CILE) and a new electrochemical biosensor was developed for determination of H₂O₂ by immobilization of hemoglobin (Hb) in the composite film of Nafion/nano‐CaCO₃ on the surface of CILE. The Hb modified electrode showed a pair of well‐defined, quasi‐reversible redox peaks with E_pa and E_pc as ?0.265 V and ?0.470 V (vs. SCE). The formal potential (E°′) was got by the midpoint of E_pa and E_pc as ?0.368 V, which was the characteristic of Hb Fe(III)/Fe(II) redox couples. The peak to peak separation was 205 mV in pH 7.0 Britton–Robinson (B–R) buffer solution at the scan rate of 100 mV/s. The direct electrochemistry of Hb in the film was carefully investigated and the electrochemical parameters of Hb on the modified electrode were calculated as α=0.487 and k_s=0.128 s^?1. The Nafion/nano‐CaCO₃/Hb film electrode showed good electrocatalysis to the reduction of H₂O₂ in the linear range from 8.0 to 240.0 μmol/L and the detection limit as 5.0 μmol/L (3σ). The apparent Michaelis–Menten constant (K_M^app) was estimated to be 65.7 μmol/L. UV‐vis absorption spectroscopy and FT‐IR spectroscopy showed that Hb in the Nafion/nano‐CaCO₃ composite film could retain its native structure.     

New insights on the Cd UPD on Au(111)

The Cd underpotential deposition (UPD) process on Au(111) was analyzed by means of combined electrochemical measurements and in situ scanning tunneling microscopy (STM). In the underpotential range 300?ΔE (mV) ?400, 2D Cd islands are formed on the fcc regions of the Au(111)‐(√3 × 22) reconstructed surface without lifting the reconstruction. At lower underpotentials, the 2D Cd islands grow and, simultaneously, new 2D islands nucleate and coalesce with the previous ones forming a complete condensed Cd monolayer (ML). STM images and long time polarization experiments performed at ΔE = 70 mV demonstrate the formation of an Au? Cd surface alloy. At ΔE = 10 mV, the formation of the complete Cd ML is accompanied by a significant Au? Cd surface alloying and the kinetic results reveal two different solid‐state diffusion processes. The first one, with a diffusion coefficient D₁ = 4 × 10^?17 cm² s^?1, could be ascribed to the mutual diffusion of Au and Cd atoms through a highly distorted (vacancy‐rich) Au? Cd alloy layer. The second and faster diffusion process (D₂ = 7 × 10^?16 cm² s^?1) is associated with the appearance of an additional peak in the anodic stripping curves and could be attributed to the formation of another Cd_zAu_x alloy phase. Copyright © 2008 John Wiley & Sons, Ltd.     

Thermal,magnetic and spectral studies of metal-quinone complexes. Part II. Media effect on Coligation of Aqua Ligands

Syntheses of phthiocol complexes with Cu(II) in inert media resulted in anhydrous monomer Cu-4: [Cu(NQ)₂] and dimer Cu-5: [Cu(NQ)(NSQ)]₂, however synthesis in air generates polymeric hydrated Cu-6: [Cu(NQ)₂(H₂O)₂]_n. Media and colligation give rise to charge transfers in coordination compounds and lead to different redox ligations of 3-methyl-2-hydroxy-1,4-naphthoquinone. These redox forms are determined from quantitization of activation energies (E _a) of different pyrolytic steps in TG using the rising temperature expression of Coats and Redfern. 'Tyrosinase'-type mechanism is discussed for the redox-type ligation. Characteristic six-line EPR signals of dimeric Cu-5 lead to zero field splitting parameters D=0.01608 cm^-1and E=0.01576 cm^-1. Cu-6 shows molecular association through hydrogen bonding. Variable temperature magnetic measurement data of Cu-6 from 6 to 300 K is fitted to the polymeric expression of Bonner and Fisher model. The best fit was obtained with antiferrromagnetic exchange coupling constantJ=-2 cm^-1, g=2.2 having R=4.2·10^-4. This revised version was published online in July 2006 with corrections to the Cover Date.     

Analysis of a quasi-reversible two-electron cyclic voltammetric wave for an organometallic ir(III)/ir(I) couple at platinum and mercury electrodes

^*CpIr(η-C₆Me₆)^2+/0 (^*Cpη⁵-C₅Me₅) displays Nernstian two-electron voltammetry at a Hg electrode, but quasi-reversible charge transfer kinetics at solid electrodes. Cyclic voltammetry (CV) peak shapes and separations change drastically from one solvent to another at Pt, ΔE_p values being as small as 170 mV in acetone and as large as 350 mV in CH₃CN (v = 0.03 V/s). These variations arise from changes in the relative E° values of the one-electron Ir(III)/Ir(II) and Ir(II)/Ir(I) couples, and from changes in charge-transfer rates. It is concluded that the Ir(II)/Ir(I) couple has a significantly lower charge-transfer rate than the Ir(III)/Ir(II) couple at platinum electrodes. The sensitivity of the CV curves to the relative E° values allows the approximate determination of the individual E° values for each one-electron process. In contrast, Nernstian conditions allow only the average of the two one-electron E° potentials to be determined. Solvents with higher solvating power are shown to facilitate the thermodynamics of the two-electron transfer process by moving E°₂ positive with respect to E°₁. Possible reasons for the abnormally slow charge transfer rates at Pt electrodes are discussed.     

Electroanalytical Studies on Cobalt(II) Ion‐Selective Sensor of Polymeric Membrane Electrode and Coated Graphite Electrode Based on N2O2 Salen Ligands

Poly(vinyl chloride)‐based membranes of salen ligands, 2‐((E)‐((1R,2S)‐2‐((E)‐5‐tert‐butyl‐2‐hydroxybenzylideneamino)cyclohexylimino)methyl)‐4‐tert‐butyl phenol (S₁) and 2‐((E)‐((1R,2S)‐2‐((E)‐3,5‐di‐tert‐butyl‐2‐hydroxybenzylideneamino)cyclohexylimino)methyl)‐4,6‐di‐tert‐butylphenol (S₂) were fabricated and explored as cobalt(II) selective electrodes. The performance of the polymeric membrane electrode (PME) and coated graphite electrode (CGE) were compared and it was observed that CGE showed a wide working concentration range of 1.1×10^?8 to 1.0×10^?1 mol L^?1 with a limit of detection of 7.0×10^?9 mol L^?1 exhibiting the Nernstian slope 29.6 mV/decade of activity in the pH range 3.0–9.0. It was used for the determination of cobalt(II) ions in water, soil, beer, pharmaceutical samples and medicinal plants and would be used as an indicator electrode in potentiometric titration with EDTA.     

Synthesis and structural studies of (2 E ,3 E ,6 R ,9 E ,11 E )-6-isopropenyl-3,6,10-trimethyl-5,8-dioxa-4,9-diazadodeca-3,9-diene-2,11-dione dioxime, ligand and its Mono-, homo, and heterodinuclear copper(II)/nickel(II) complexes

This article describes the synthesis of a new (2E,3E,6R,9E,11E)-6-isopropenyl-3,6,10-trimethyl-5,8-dioxa-4,9-diazadodeca-3,9-diene-2,11-dione dioxime (H₂hmdm), and its mono-, homo, and heterodinuclear copper(II)/nickel(II) complexes. Elemental analyses, stoichiometric and spectroscopic data of the metal complexes indicated that the metal ions are coordinated to the oxime and imine nitrogen atoms (C=N). The Cu(H₂hmdm), molecule coordinates to the second copper(II) ion through the oximate oxygens to afford a binuclear structure doubly bridged by the oximate groups in the cis arrangement. In the dinuclear complexes, in which the first Cu^II ion was complexed with nitrogen atoms of the oxime and imine groups, the second Cu^II ion is ligated with the 1,10-phenanthroline nitrogen atoms. Ligand and its mononuclear copper(II), homo and heterodinuclear copper(II)–nickel(II) complexes of (H₂hmdm) were characterized by elemental analyses, magnetic moments, ¹H-n.m.r. and ¹³C-n.m.r., i.r., and mass spectral studies. The data support the proposed structure of H₂hmdm and its complexes.