Redox behavior and transport properties of La0.5−2xCexSr0.5+xFeO3−δ and La0.5−2ySr0.5+2yFe1−yNbyO3−δ perovskites

The effects of doping the mixed-conducting (La,Sr)FeO_3−δ system with Ce and Nb have been examined for the solid-solution series, La_0.5−2xCe_xSr_0.5+xFeO_3−δ (x = 0–0.20) and La_0.5−2ySr_0.5+2yFe_1−yNb_yO_3−δ (y = 0.05–0.10). Mössbauer spectroscopy at 4.1 and 297 K showed that Ce⁴⁺ and Nb⁵⁺ incorporation suppresses delocalization of p-type electronic charge carriers, whilst oxygen nonstoichiometry of the Ce-containing materials increases. Similar behavior was observed for La_0.3Sr_0.7Fe_0.90Nb_0.10O_3−δ at 923–1223 K by coulometric titration and thermogravimetry. High-temperature transport properties were studied with Faradaic efficiency (FE), oxygen-permeation, thermopower and total-conductivity measurements in the oxygen partial pressure range 10⁻⁵–0.5 atm. The hole conductivity is lower for the Ce- and Nb-containing perovskites, primarily as a result of the lower Fe⁴⁺ concentration. Both dopants decrease oxide-ion conductivity but the effect of Nb-doping on ionic transport is moderate and ion-transference numbers are higher with respect to the Nb-free parent phase, 2.2 × 10⁻³ for La_0.3Sr_0.7Fe_0.9Nb_0.1O_3−δ cf. 1.3 × 10⁻³ for La_0.5Sr_0.5FeO_3−δ at 1223 K and atmospheric oxygen pressure. The average thermal expansion coefficients calculated from dilatometric data decrease on doping, varying in the range (19.0–21.2) × 10⁻⁶ K⁻¹ at 780–1080 K.     

Electrode properties of Sr doped La2CuO4 as new cathode material for intermediate-temperature SOFCs

High performance La_2−xSr_xCuO_4−δ (x = 0.1, 0.3, 0.5) cathode materials for intermediate temperature solid oxide fuel cell (IT-SOFCs) were prepared and characterized. The investigation of electrical properties indicated that La_1.7Sr_0.3CuO₄ cathode has low area specific resistance (ASR) of 0.16 Ω cm² at 700 °C and 1.2 Ω cm² at 500 °C in air. The rate-limiting step for oxygen reduction reaction on La_1.7Sr_0.3CuO₄ electrode changed with oxygen partial pressure and measurement temperature. La_1.7Sr_0.3CuO₄ cathode exhibits the lowest overpotential of about 100 mV at a current density of 150 mA cm⁻² at 700 °C in air.     

Beneficial modification of the properties of multiferroic BiFeO3 by cation substitution

The effects of modifying the well-known multiferroic BiFeO₃ by substituting Fe by Mn and Bi by La have been investigated. It is shown that both the substitutions have a favourable effect on the multiferroic properties of BiFeO₃. Thus, both BiFe_1−xMn_xO₃ and Bi_1−xLa_xFeO₃ (x = 0.0–0.3) show increased magnetization accompanied by hysteresis loops as well as improved dielectric properties. The ferroelectric transition temperature is lower than that of BiFeO₃, but is in a more accessible range. In Bi_1−xLa_xFeO₃, there is a change in structure at x = 0.2.     

Li(4−x)/3Ti(5−2x)/3CrxO4 (0 ≤ x ≤ 0.9) spinels: New negatives for lithium batteries

Members of the spinel solid solution between Li_4/3Ti_5/3O₄ and LiCrTiO₄, i.e., Li_(4−x)/3Ti_(5−2x)/3Cr_xO₄ (0 ≤ x ≤ 0.9), have been investigated as possible negative electrodes for future lithium-ion batteries. Electrochemical behaviour have been studied over the potential range 1–3.5 V vs Li⁺/Li. Results are promising with anodic capacities between 129 and 163 mA h/g with a flat operating voltage at about 1.5 V, which is attributed to the pair Ti⁴⁺/Ti³⁺. The inclusion of Cr³⁺ in the spinel structure enhances the specific capacity. In-situ X-ray diffraction experiments confirm that the reaction proceeds in a topotactic manner.     

First principles study of structure and properties of La- and Mn-modified BiFeO3

First principles calculations have been performed to study the effects of the La³⁺ and Mn³⁺ substitutions in the multiferroic BiFeO₃. The real compositions Bi_1−xLa_xFeO₃ and BiFe_1−xMn_xO₃ with x = 0.0, 0.1, 0.2, 0.3 were modeled by substitution of one, two and three Bi³⁺ or Fe³⁺ by La³⁺ or Mn³⁺ in the orthorhombic BiFeO₃ structure, respectively. Density functional theory within the generalized gradient approximation with Hubbard correction of Dudarev (GGA + U) and plane wave pseudo-potential approach has been used to track the changes that occur in the structural parameters, electronic structure, magnetic, optical and polarization properties of the modified BiFeO₃. The substitution of one Bi³⁺ with La³⁺ increases the band gap energy whereas the augmentation of La³⁺ substitutes decreases it. The substitutions of Fe³⁺ with Mn³⁺ do not change the band gap energy. The calculations predicted larger polarization of the modified BiFeO₃, antiferromagnetism for Bi_1−xLa_xFeO₃ and small ferrimagnetism for BiFe_1−xMn_xO₃. Better multiferroic properties are expected for BiFe_1−xMn_xO₃ materials (x = 0.1, 0.2) due to the increasing polarization and ferrimagnetic behavior. The optical properties were estimated by the calculated imaginary and real parts of the dielectric function. The increase of La³⁺ and Mn³⁺ substitutes lead to lower absorption intensity at energy range 2–7 eV.     

Electrochemical performance of La-doped Sr2MgMoO6−δ in natural gas

Modification of the double perovskite Sr₂MgMoO_6−δ by La substitution has shown that Sr_2−xLa_xMgMoO_6−δ with 0.6 ⩽ x ⩽ 0.8 has better performance as the anode of a solid oxide fuel cell. With a Sr_1.2La_0.8MgMoO_6−δ anode, LSGM electrolyte, SrCo_0.8Fe_0.2O_3−δ cathode, and a La_0.5Ce_0.4O_1.7−δ buffer layer between the anode and the electrolyte, a maximum power density of 550 mW/cm² has been obtained for a SOFC operating on wet methane (3%H₂O) at 800 °C. The performance of the SOFC using C₂H₆ fuel, like that of CH₄, changes little on switching from dry C₂H₆ to 3% H₂O/C₂H₆, but improvement with wet C₃H₈ shows that some steam will need to be added to a moderately desulfurized natural-gas fuel.     

Perovskite-type oxides for high-temperature oxygen separation membranes

Oxygen permeation through dense ceramic membranes of perovskite-like SrCo_0.9−xFe_0.1Cr_xO_3−δ (x = 0.01–0.05), Sr_1−x−yLn_xCoO_3−δ(Ln = La, Nd, Sm, Gd; x = 0.30–0.35; y = 0–0.10), SrCo_1−xTi_xO_3−δ (x = 0.05–0.20) and LaM_1−xNi_xO_3−δ (M = Ga, Co, Fe; x = 0–0.6) was studied. The SrCoO_3−δ-based solid solutions with cubic perovskite structure were found to exhibit highest permeation fluxes compared to other membranes. However, high thermal expansion coefficients and interaction with gas species such as carbon dioxide may complicate the employment of SrCoO_3−δ membranes for oxygen separation membranes. Alternatively, the LaGa_1−xNi_xO_3−δ (x = 0.2–0.5) perovskites, having significant permeation fluxes as well as thermal expansion coefficients in the range of (10.8–11.6) × 10⁻⁶ K⁻¹, were demonstrated to be suitable as membrane materials at oxygen pressures from 1 × 10⁻² to 2 × 10⁴ Pa. Testing oxygen permeation at oxygen partial pressures of 1–60 atm showed that only oxides with a high oxygen deficiency such as SrCo_0.85Ti_0.15F_3−δ possess sufficient oxygen permeation fluxes. The oxygen permeability of perovskites on the basis of LaGaO₃ and LaCoO_3−δ was found to be negligible at oxygen pressures above 15 atm, caused by low oxygen vacancy concentration and ionic conductivity of such ceramic materials.     

Study on the effect of Li doping in spinel Li4+xTi5−xO12 (0 ⩽ x ⩽ 0.2) materials for lithium-ion batteries

The effect of Li doping in spinel Li_4+xTi_5−xO₁₂ (0 ⩽ x ⩽ 0.2) materials on the structural and electrochemical properties were investigated. The ratio of the capacity in the voltage plateau (1.5 V) to the overall discharge capacity for Li_4.1Ti_4.9O₁₂ (x = 0.1) and Li_4.2Ti_4.8O₁₂ (x = 0.2) were higher than that of Li₄Ti₅O₁₂ especially at high current rates due to their enhanced lithium-ion and electronic conductivity by the substitution of Ti atoms by Li atoms. With the increasing of Li doping amount, lithium-ion and electronic conductivity of Li_4+xTi_5−xO₁₂ increased, however its cycling stability was depressed when the Li doping was of x = 0.2. The Li doping of x = 0.1, the appropriate Li doping amount, showed improved rate capability and better high rate performance comparing to undoped Li_4+xTi_5−xO₁₂ (x = 0).     

Hopping conduction in double layered La2−2xCa1+2xMn2O7 manganite

Double layered La_2−2xCa_1+2xMn₂O₇ manganite has been synthesized using solid state reaction method for different dopant concentration x = 0.0–0.5. Their temperature dependence of resistivity (ρ − T) has been studied in the semiconducting region. The experimental observations were compared with the theoretically simulated temperature dependence of resistivity curves based on nearest neighbour hopping, Efros–Shklovskii variable range hopping, and Mott's 2D and 3D variable range hopping models. From the analysis of these results, Mott's 3D variable range hopping mechanism seemed to be most suitable mechanism describing the semiconducting behaviour of these double layered manganites. Temperature dependent activation energy also supported the Mott's 3D variable range hopping model. The Mott's activation energy was found to vary with the dopant concentration x and it showed a minimum value for x = 0.3.     

Direct synthesis of La-Mg-Ni-Co type hydrogen storage alloys from oxide mixtures

(La_(1-x)Mg_x)_2(Ni_(0.8)Co_(0.2))_7(x = 0.125, 0.25, 0.5) alloys were synthesized from the sintered mixture of La_2O_3+ Ni O + Co O + Mg O in the molten CaCl_2 electrolyte at 750 °C and the electrochemical hydrogen storage capacities of the synthesized alloys were measured. Non-hygroscopic LaNiO_3 phase formed during sintering(at 1200 °C for 2 h) as a result of the reaction of hygroscopic La_2O_3 with NiO. Another sinter product was Mg_(0.4)Ni_(0.6)O phase. Both mixed oxide sinter products facilitated the La-Ni and Mg-Ni phase formations. X-ray diffraction peaks indicated that the first stable phase appeared in the alloy structure was LaNi_5 which formed upon reduction of La_2NiO_4 phase. Increase in Mg content caused formation of La_(1.5)Mg_(0.5)Ni_7 phase in the alloy structure and the presence of this phase improved the hydrogen storage performance of the electrodes. It was observed that(La_(1-x)Mg_x)_2(Ni_(0.8)Co_(0.2))_7(x = 0.125, 0.25, 0.5) alloys have promising discharge capacities change between 319 m Ah/g and 379 m Ah/g depending on the alloy Mg content.     

Synthesis and characterization of A-site deficient rare-earth doped BaZrxTi1−xO3 perovskite-type compounds

A-site deficient rare-earth doped BaZr_xTi_1?xO₃ (BZT) ceramics were prepared from a soft-chemistry route and by solid-state reaction (SSR). Perovskite-like single-phase diagrams for the BaTiO₃–La_2/3TiO₃–BaZrO₃ system were constructed for each method of synthesis. Infrared spectroscopy on (Ba_1?yLa_2y/3)Zr_xTi_1?xO₃ solid solution revealed a dramatic stress on the M–O (M = Ti, Zr) bonds due to the combined effect of A-site vacancies and the lower ionic radius of La³⁺ than that of Ba²⁺. A relationship between the M–O stretching vibration (υ) and the tolerance factor (t) was determined. (Ba_1?yLn_2y/3)Zr_0.09Ti_0.91O₃ (Ln = La, Pr, Nd) samples synthesized by SSR were selected for detailed studies. X-ray diffraction data were refined by the Rietveld method. Scanning electron microscopy on sintered compacts detected abnormal crystal growth and grain sizes in the range of about 1 μm up to 10 μm when the dopant concentration is 6.7 at. %. Impedance measurements exhibited that ferroelectric to paraelectric phase-transition temperature shifted to lower values as increasing rare-earth content. (Ba_1?yLn_2y/3)Zr_0.09Ti_0.91O₃ system showed a diffuse phase transition with a relaxor-like ferroelectric behaviour. Furthermore, the dielectric constant was enhanced with respect to non-doped BZT system.     

Surface modification of La0.3Sr0.7CoO3−δ ceramic membranes

The dependence of oxygen permeability of dense La_0.3Sr_0.7CoO_3−δ ceramics on membrane thickness indicates significant surface exchange limitations to the permeation fluxes, which suggests a possibility to increase membrane performance by surface activation. The cobaltite membranes with various porous layers applied onto the permeate-side surface were tested at 850–1120 K. Silver-modified La_0.3Sr_0.7CoO_3−δ membranes showed enhanced permeation at temperatures above 950 K; deposition of porous layers of PrO_x and Pr_0.7Sr_0.3CoO_3−δ had no positive effect. The maximum oxygen permeability at 850–1120 K was observed in the case of porous La_0.3Sr_0.7CoO_3−δ layers with surface density about 10 mg cm⁻². These results suggest that the surface exchange of lanthanum–strontium cobaltite membranes under an oxygen chemical potential gradient is limited by both oxygen sorption at the surface and ion diffusion through the surface oxide layers. Oxygen permeability of La_0.3Sr_0.7CoO_3−δ ceramics was found to increase with increasing grain size due to decreasing grain-boundary resistance to ionic transport.     

A quantitative colorimetric assay of H2O2 and glucose using silver nanoparticles induced by H2O2 and UV

A simple spectrophotometric assay of H2O2 and glucose using Ag nanoparticles has been carried out. Relying on the synergistic effect of H2O2 reduction and ultraviolet （UV） irradiation, Ag nanoparticles with enhanced absorption signals were synthesized. H2O2 served as a reducing agent in the Ag nanoparticles formation in which Ag＋ was reduced to Ago by O2- generated via the decomposition of H2O2 in alkaline media. On the other hand, photoreduction of Ag＋ to Ago under UV irradiations also contributed to the nanoparticles formation. The synthesized nanoparticles were characterized by TEM, XPS, and XRD. The proposed method could determine H2O2 with concentrations ranging from 5.0× 10^-7 to 6.0× 10^-5 tool/ L The detection limit was estimated to be 2.0 × 10^-7 mol/L. Since the conversion of glucose to gluconic acid catalyzed by glucose oxidase was companied with the formation of H2O2, the sensing protocol has been successfully utilized for the determination of glucose in human blood samples. The results were in good agreement with those determined by a local hospital. This colorimetric sensor thus holds great promises in clinical applications.     

Tunable lithium storage properties of metal lithium titanates by stoichiometric modulation

A simple stoichiometric modulation of Na_2 − 2xSr_xLi₂Ti₆O₁₄ was developed to achieve tunable electrochemical properties of the material. The concept was confirmed experimentally and theoretically using density functional theory (DFT) calculations. Both the operating potential and the amount of reversibly intercalated lithium ions were manipulated by simply changing the Na/Sr ratio. These unique characteristics originated from a gradual change in the electron density on the Ti atoms and the extra lithium insertion sites at SrLi₂Ti₆O₁₄. As a promising anode material for lithium-ion batteries, Na_2 − 2xSr_xLi₂Ti₆O₁₄ and its tunable electrochemical properties have significant importance in terms of the development of tailored electrodes with desirable electrochemical performance.     

Thermodynamic properties of Na2Ti6O13 and Na2Ti3O7: electrochemical and calorimetric determination

Standard values of Gibbs free energy, entropy, and enthalpy of Na₂Ti₆O₁₃ and Na₂Ti₃O₇ were determined by evaluating emf-measurements of thermodynamically defined solid state electrochemical cells based on a Na–β″-alumina electrolyte. The central part of the anodic half cell consisted of Na₂CO₃, while two appropriate coexisting phases of the ternary system Na–Ti–O are used as cathodic materials. The cell was placed in an atmosphere containing CO₂ and O₂. By combining the results of emf-measurements in the temperature range of 573⩽T/K⩽1023 and of adiabatic calorimetric measurements of the heat capacities in the low-temperature region 15⩽T/K⩽300, the thermodynamic data were determined for a wide temperature range of 15⩽T/K⩽1100. The standard molar enthalpy of formation and standard molar entropy at T=298.15 K as determined by emf-measurements are Δ_fH_m⁰=(−6277.9±6.5) kJ · mol⁻¹ and S_m⁰=(404.6±5.3) J · mol⁻¹ · K⁻¹ for Na₂Ti₆O₁₃ and Δ_fH_m⁰=(−3459.2±3.8) kJ · mol⁻¹ and S_m⁰=(227.8±3.7) J · mol⁻¹ · K⁻¹ for Na₂Ti₃O₇. The standard molar entropy at T=298.15 K obtained from low-temperature calorimetry is S_m⁰=399.7 J · mol⁻¹ · K⁻¹ and S_m⁰=229.4 J · mol⁻¹ · K⁻¹ for Na₂Ti₆O₁₃ and Na₂Ti₃O₇, respectively. The phase widths with respect to Na₂O content were studied by using a Na₂O-titration technique.     

Li2CuTi3O8–Li4Ti5O12 double spinel anode material with improved rate performance for Li-ion batteries

Ti-based anode materials with the nominal compositions Li₄Ti₅Cu_xO_12 + x (x = 0, 0.075, 0.15, 0.3, 0.6, 1.20 and 1.67) were synthesized at 800 °C by a solid-state reaction process. X-ray diffraction analysis indicated that the sintered samples were composed of intergrown spinel-type Li₄Ti₅O₁₂ and Li₂CuTi₃O₈, and a small amount of Li₂O. Scanning electron microscopy, electrical resistance measurement and galvanostatic cell cycling were also employed to characterize the structure and properties of the double spinel samples. It is proposed that the first lithiation of the component Li₂CuTi₃O₈ leads to the in situ production of Cu that can significantly improve the rate performance of Li₄Ti₅Cu_xO_12 + x. The optimal nominal composition is Li₄Ti₅Cu_0.15O_12.15.     

Study of the ionic conductivity of Ca6La4(PO4)2(SiO4)4F2 and Ca4La6(SiO4)6F2

In order to enhance our knowledge about the Ca_10−xLa_x(PO₄)_6−x(SiO₄)_xF₂ (0 ≤ x ≤ 6) series, whose chemical stability decreases as the substitution degree increases, Ca₆La₄(PO₄)₂(SiO₄)₄F₂ and Ca₄La₆(SiO₄)₆F₂ compounds were prepared through a solid-state reaction. Their ionic conductivity was measured by impedance spectroscopy. The results indicate that the conductivity increases with substitution, and fits the Arrhenius equation over the investigated temperature range. At high temperatures, a change in the activation energy has been observed, which has been related to the nature of the Ca/La–F bond, i.e. to the polarizability of lanthanum.     

Structural properties of silver nanoclusters–phosphate glass composites

The structure of the xAg₂O(100 − x)[50P₂O₅·30CaO·20Na₂O] glasses, with x = 0, 3 and 5 mol%, was investigated by means of Raman and infrared spectroscopy. The structural changes induced by the Ag₂O presence into the soda-calcium–phosphate matrix were evidenced and discussed in terms of the network depolymerization process and distortion of the PO₄ tetrahedra. The existence of silver nanoclusters inside the glass matrix, considered to be mainly responsible for the found structural behavior, was supposed by results obtained from the analysis of the UV–vis absorption spectra and further proved by transmission electron microscopy images.     

Solution synthesis and electrical properties of K2NiF4 type LaSrAlO4

K₂NiF₄ type LaSrAlO₄ was synthesised by sol–gel and combustion methods at 1300 °C and characterised by X-ray diffraction (XRD). DC electrical conductivity studies revealed that LaSrAlO₄ is an n-type conductor at low oxygen partial pressures and a p-type conductor at near atmospheric pressures with conductivity of the order of 10⁻⁴ S cm⁻¹. Dilatometric measurements indicated a nonlinear increase in the thermal expansion coefficient, corroborated by a nonlinear expansion along the a axis determined by high temperature XRD. Attempts to synthesise oxygen excess La_1+xSr_1−xAlO_4+δ phases by varying the La:Sr ratio always resulted in a La₂O₃ secondary impurity phase.     

Raman spectroscopy investigation on (Pb1−xLax)(Zr0.90Ti0.10)1−x/4O3 ceramic system

A Raman spectroscopy study at room temperature was carried out on (Pb_1−xLa_x)(Zr_0.90Ti_0.10)_1−x/4O₃ ceramics (x = 2, 3, 4 at%). The results were analyzed considering the x-ray patterns at room temperature showing a mixture of two phases: a rombohedral-ferroelectric phase and an orthorhombic-antiferroelectric, increasing the% of the second one with the lanthanum concentration. For x = 3 at%, the analysis was also carried out in a wide temperature range. Two anomalies were evaluated, one around 363 K, which has been associated to a ferroelectric-antiferroelectric phase transition; the second one around 430 K, which has been associated to a transition from an incommensurable state to a ferroelectric phase.