Annealing effects on the structural and electrical transport properties of n-type Bi2Te2.7Se0.3 thin films deposited by flash evaporation

N-type Bi₂Te_2.7Se_0.3 thermoelectric thin films with thickness 800 nm have been deposited on glass substrates by flash evaporation method at 473 K. Annealing effects on the thermoelectric properties of Bi₂Te_2.7Se_0.3 thin films were examined in the temperature range 373-573 K. The structures, morphology and chemical composition of the thin films were characterized by X-ray diffraction, field emission scanning electron microscope and energy dispersive X-ray spectroscopy, respectively. Thermoelectric properties of the thin films have been evaluated by measurements of the electrical resistivity and Seebeck coefficient at 300 K. The Hall coefficients were measured at room temperature by the Van der Pauw method. The carrier concentration and mobility were calculated from the Hall coefficient. The films thickness of the annealed samples was measured by ellipsometer. When annealed at 473 K, the electrical resistivity and Seebeck coefficient are 2.7 mΩ cm and −180 μV/K, respectively. The maximum of thermoelectric power factor is enhanced to 12 μW/cm K².     

Optical and thermoelectric characterizations of electroplated n-Bi2(Te0.9Se0.1)3

Bismuth selenotelluride (Bi₂(Te_0.9Se_0.1)₃) films were electrodeposited at constant current density from acidic aqueous solutions with Arabic gum in order to produce thin films for miniaturized thermoelectric devices. X-ray fluorescence spectroscopy determined film compositions. X-ray diffraction pattern shows that the films as deposited are polycrystalline, isostructural to Bi₂Te₃ and covered by crystallites. Mueller-matrix analysis reveals that the electroplated layers are optically like an isotropic medium. Their pseudo-dielectric functions were determined using mid-infrared spectroscopic ellipsometry. Tauc-Lorentz combined with Drude dispersion relations were successfully used. The energy band gap E_g was found to be about 0.15 eV. Moreover, the fundamental absorption edge was described by an indirect optical band-to-band transition. From Seebeck coefficient measurement, films exhibit n-type charge carrier and the value of thermoelectric power is about −40 μV/K.     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

Annealing effects on structural, optical and electrical properties of e-beam evaporated CuIn0.5Ga0.5Te2 thin films

CuIn_0.5Ga_0.5Te₂ (CIGT) thin films have been prepared by e-beam evaporation from a single crystal powder synthesized by direct reaction of constituent elements in a stoichiometric proportion. Post-depositional annealing has been carried out at 300 and 350 °C. The compositions of the films were determined by energy dispersive X-ray analysis (EDXA) and it was found that there was a remarkable fluctuation in atomic percentage of the constituent elements following to the post-depositional annealing. X-ray diffraction analysis (XRD) has shown that as-grown films were amorphous in nature and turned into polycrystalline structure following to the annealing at 300 °C. The main peaks of CuIn_0.5Ga_0.5Te₂ and some minor peaks belonged to a binary phase Cu₂Te appeared after annealing at 300 °C, whereas for the films annealed at 350 °C single phase of the CuIn_0.5Ga_0.5Te₂ chalcopyrite structure was observed with the preferred orientation along the (1 1 2) plane. The effect of annealing on and near surface regions has been studied using X-ray photoelectron spectroscopy (XPS). The results indicated that there was a considerable variation in surface composition following to the annealing process. The transmission and reflection measurements have been carried out in the wavelength range of 200-1100 nm. The absorption coefficients of the films were found to be in the order of 10⁴ cm⁻¹ and optical band gaps were determined as 1.39, 1.43 and 1.47 eV for as-grown and films annealed at 300 and 350 °C, respectively. The temperature dependent conductivity and photoconductivity measurements have been performed in the temperature range of −73 to 157 °C and the room temperature resistivities were found to be around 3.4 × 10⁷ and 9.6 × 10⁶ (Ω cm) for the as-grown and annealed films at 350 °C, respectively.     

Effect of composition and thermal annealing on the absorption and electrical conduction of Se85−xTe15Sbx glasses

The optical absorption of the as-prepared and thermally annealed Se_85−xTe₁₅Sb_x (0≤x≤9) thin films was measured. The mechanism of the optical absorption follows the rule of non-direct transition. The optical energy gap (E₀) decreased from 1.12 to 0.84 eV with increasing Sb content of the as-prepared films from 0 to 9 at.%. The as-prepared Se₇₆Te₁₅Sb₉ films showed an increase in (E₀) with increasing the temperature of annealing in the range above T_g (363 K). The electrical conductivity of the as-prepared and annealed films was found to be of Arrhenius type with temperature in the range 300-360 K. The activation energy for conduction was found to decrease with increasing both the Sb content and temperature of annealing. The results were discussed on the basis of the lone-pair electron effect and of amorphous crystalline transformation.     

Electrical transport and high thermoelectric properties of PbTe doped with Bi2Te3 prepared by HPHT

In this paper, n-type lead telluride (PbTe) compounds doped with Bi₂Te₃ have been successfully prepared by high pressure and high temperature (HPHT) technique. The composition-dependent thermoelectric properties of PbTe doped with Bi₂Te₃ have been studied at room temperature. The figure-of-merit, Z, for PbTe is very sentivite to the dopants, which could be improved largely although the doped content of Bi₂Te₃ is very small (<0.08 mol%). In addition, the maximum value reaches to 9.3×10⁻⁴ K⁻¹, which is about 20% higher than that of PbTe alloyed with Bi₂Te₃ sintered at ambient pressure (7.6×10⁻⁴ K⁻¹) and several times higher than that of small grain size PbTe containing other dopants. The improved thermoelectric performance in this study may be due to the effect of high pressure and the low lattice thermal conductivity resulting from Bi₂Te₃ as source of dopants.     

Bi-Sb-Te基热电薄膜温差电池离子束溅射制备与表征

本文采用离子束溅射Bi/Te和Sb/Te二元复合靶,直接制备n型Bi₂Te₃热电薄膜和p型Sb₂Te₃热电薄膜.在退火时间同为1 h的条件下,对所制备的Bi₂Te₃薄膜和Sb₂Te₃薄膜进行不同温度的退火处理,并对其热电性能进行表征.结果表明,在退火温度为150 ℃时,制备的n型Bi₂Te₃关键词： 薄膜温差电池 2Te₃薄膜')" href="#">Sb₂Te₃薄膜 2Te₃薄膜')" href="#">Bi₂Te₃薄膜 离子束溅射     

Low-temperature thermoelectric properties of Bi85Sb15−xNbx alloys prepared by high-press sintering

The nanocrystalline materials with the general formula Bi₈₅Sb_15−xNb_x (x=0, 0.5, 1, 2, 3) were prepared by mechanical alloying and subsequent high-pressure sintering. Their transport properties involving electrical conductivity, Seebeck coefficient and thermal conductivity have been investigated in the temperature range of 80-300 K. The absolute value of Seebeck coefficient of Bi₈₅Sb₁₃Nb₂ reaches a maximum of 161 μV/K at 105 K, which is 69% larger than that of Bi₈₅Sb₁₅ at the same temperature. The power factor and figure-of-merit are 4.45×10⁻³ WK⁻²m⁻¹ at 220 K and 1.79×10⁻³ K⁻¹ at 196 K, respectively. These results suggest that thermoelectric properties of Bi₈₅Sb₁₅ based material can be improved by Nb doping.     

Fabrication of nanostructured CuInS2 thin films by ion layer gas reaction method

CuInS₂ thin films were prepared by a two-stage ion layer gas reaction (ILGAR) process in which the Cu and In precursors were deposited on glass substrate by using a simple and low-cost dip coating technique and annealed in H₂S atmosphere at different temperatures. The influence of the annealing temperature (250-450 °C) on the particle size, crystal structure and optical properties of the CuInS₂ thin films was studied. Transmission electron microscopy revealed that the particle radii varied in the range 6-21 nm with annealing. XRD and SAED patterns indicated polycrystalline nature of the nanoparticles. The optical band gap (E_g) varied from 1.48 to 1.56 eV with variation of particle size. The variation of Urbach tail with temperature indicated higher density of the defects for the films annealed at lower temperature. From the Raman study, it was observed that the FWHM of the A₁ mode at ∼292 cm⁻¹ corresponding to the chalcopyrite phase of CuInS₂ decreased with increasing annealing temperature.     

Electrodeposition of n-type Bi2Te3−ySey thermoelectric thin films on stainless steel and gold substrates

Thermoelectric films of n-Bi₂Te_3−ySe_y were prepared by potentiostatic electrodeposition technique onto stainless steel and gold substrates at room temperature. These films were used for morphological, compositional and structural analysis by environment scanning electron microscope (ESEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The effect of different substrates on the structure and morphology of Bi₂Te_3−ySe_y films and relation between Se content in the electrodepositing solutions and in the films were also investigated. These studies revealed that Bi, Te and Se could be co-deposited to form Bi₂Te_3−ySe_y semiconductor compound in the solution containing Bi³⁺, HTeO₂⁺ and H₂SeO₃. The morphology and structure of the films are sensitive to the substrate material. The doped content of Se element in the Bi₂Te_3−ySe_y compound can be controlled by adjusting the Se⁴⁺ concentration in the electrodepositing solution. X-ray diffraction analysis indicates that the films prepared at −40 mV versus saturated calomel electrode (SCE) exhibit strong (1 1 0) orientation with rhombohedral structure.     

Effect of annealing temperature on the optical and electrical properties of amorphous As45.2Te46.6In8.2 thin films

The optical absorption of the As-prepared and annealed As_45.2Te_46.6In_8.2 thin films are studied. Films annealed at temperatures higher than 453 K show a decrease in the optical energy gap (E_o). The value of E_o increases from 1.9 to 2.43 eV with increasing thickness of the As-prepared films from 60 to 140 nm. The effect of thickness on high frequency dielectric constant (?_∞) and carrier concentration (N) is also studied. The crystalline structures of the As_45.2Te_46.6In_8.2 thin films resulting from heat treatment of the As-prepared film at different elevated temperatures is studied by X-ray diffraction. An amorphous-crystalline transformation is observed after annealing at temperatures higher than 453 K. The electrical conductivity at low temperatures is found due to the electrons transport by hopping among the localized states near the Fermi level. With annealing the films at temperatures higher than 473 K (the crystallization onset temperature) for 1 h, the electrical conductivity increases and the activation energy decreases, which can be attributed to the amorphous-crystalline transformations.     

Influence of heating rate on the crystalline properties of 0.7BiFeO3-0.3PbTiO3 thin films prepared by sol-gel process

0.7BiFeO₃-0.3PbTiO₃ (BFPT7030) thin films were deposited on SiO₂/Si substrates by sol-gel process. The influence of heating rate on the crystalline properties of BFPT7030 thin films were studied by X-ray diffraction (XRD), scanning electron microscope (SEM), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). XRD patterns of the films showed that a pure perovskite phase exists in BFPT7030 films annealed by rapid thermal annealing (RTA) technique. SEM and AFM observations demonstrated that the BFPT7030 films annealed by RTA at 700 °C for 90 s with the heating rate of 1 °C s⁻¹ could show a dense, crack-free surface morphology, and the films’ grains grow better than those of the films annealed by RTA at the same temperature with other heating rates. XPS results of the films indicated that the ratio of Fe³⁺:Fe²⁺ is about 21:10 and 9:5 for the films annealed by RTA at 700 °C for 90 s with the heating rate of 1 and 20 °C s⁻¹, respectively. That means the higher the heating rate, the higher the concentration of Fe²⁺ in the BFPT7030 thin films.     

Preference orientation and magnetic properties of CoxFe3−xO4 nanocrystalline thin films on quartz substrate

Nanocrystalline spinel ferrite thin films of Co_xFe_3−xO₄ (x=0.3$x=0.3$, 0.5, 0.8, and 1.0) have been prepared by RF sputtering on quartz substrate without a buffer layer at room temperature and annealed at the temperature range from 200 to 600 °C in air. The as-sputtered films exhibit the preferred orientation and the high magnetization and coercivity. After annealing, the preferred orientations become poor, but the magnetization and coercivity increase. The sample with a magnetization of 455 emu/cm³, a coercivity of 2.8 kOe, a remanence ratio of 0.72, and a maximum energy product of 2.4 MGOe has been obtained. The influence of Co ions and annealing temperature on the magnetic properties has been discussed.     

Synthesis and characterisation of Gd-doped BaTiO3 thin films prepared by laser ablation for optoelectronic applications

The results of gadolinium (Gd)-doped barium titanate (BaTiO₃) thin films prepared by laser ablation on glass and silicon substrates are reported. Rutherford backscattering (RBS) analyses carried out on glass samples indicated the substitution of barium (Ba) by gadolinium (Gd) after annealing, leading to a film with composition Ba_0.76TiGd_0.01O_2.5. There is a reduction in the thickness from 2.21 to 2.02 microns for as-deposited and annealed films. The films on silicon showed a higher degree of crystallinity compared to that of glass substrates due to increased annealing temperature. The average grain size calculated using the X-ray diffraction (XRD) pattern from silicon substrates was 30 nm. The film has a tetragonal structure with a “c/a” ratio of 1.03 signifying that the incorporation of Gd in BaTiO₃ led to the elongation of the c-axis. The percentage transmittance reduced from 80 to 50% due to annealing and this is probably due to structural changes in the film. Swanepoel envelope method employed on the interference fringes of the transmittance pattern led to the determination of the variation of the refractive index with wavelength. Sellmier single oscillator model was applied to determine the optical constants of the films on glass substrates. Bandgap analyses carried out showed the reduction in bandgap with annealing and also the possibility that Gd incorporation has modified the film chemistry leading to the existence of direct (4.35 eV) and indirect (3.88 eV) allowed transitions in the annealed films. Dielectric property measurement carried out under ambient conditions gave a relaxation time τ of 1.6×10⁻⁴ s and conduction by small polaron with the onset of polaron conduction set at about 7 kHz. It is conjectured that these properties, especially the high refractive index and the high bandgaps, can make Gd-doped BaTiO₃ a good candidate for optoelectronic applications.     

Laser-induced voltage characteristics of Bi2Sr2Co2Oy thin films on LaAlO3 substrates

We report the laser-induced voltage (LIV) effects in c-axis oriented Bi₂Sr₂Co₂O_y thin films grown on (0 0 1) LaAlO₃ substrates with the title angle α of 0°, 3°, 5° and 10° by a simple chemical solution deposition method. A large open-circuit voltage with the sensitivity of 300 mV/mJ is observed for the film on 10° tilting LaAlO₃ under a 308 nm irradiation with the pulse duration of 25 ns. When the film surface is irradiated by a 355 nm pulsed laser of 25 ps duration, a fast response with the rise time of 700 ps and the full width at half maximum of 1.5 ns is achieved. In addition, the experimental results reveal that the amplitude of the voltage signal is approximately proportional to sin 2α and the signal polarity is reversed when the film is irradiated from the substrate side rather than the film side, which suggests the LIV effects in Bi₂Sr₂Co₂O_y thin films originate from the anisotropic Seebeck coefficient of this material.     

High-throughput characterization of BixY3−xFe5O12 combinatorial thin films by magneto-optical imaging technique

Bi_xY_3−xFe₅O₁₂ thin films have been grown on GGG (Gd₃Ga₅O₁₂) (1 1 1) substrates by the combinatorial composition-spread techniques under substrate temperature (T_sub) ranging from 410 to 700 °C and O₂ pressure of 200 mTorr. In order to study the effect of substrates on the deposition of Bi_xY_3−xFe₅O₁₂ thin films, garnet substrates annealed at 1300 °C for 3 h were also used. Magneto-optical properties were characterized by our home-designed magneto-optical imaging system. From the maps of Faraday rotation angle θ_F, it was evident that the Faraday effect appears only when T_sub = 430-630 °C. θ_F reaches to the maximum value (∼6°/μm, λ = 632 nm) at 500 °C, and is proportional to the Bi contents. XRD and EPMA analyses showed that Bi ions are easier to substitute for Y sites and better crystallinity is obtained for annealed substrates than for commercial ones.     

Investigation of p-type behavior in Ag-doped ZnO thin films by E-beam evaporation

Ag-doped ZnO (ZnO:Ag) thin films were grown on glass substrates by E-beam evaporation technique. The structural, electrical and optical properties of the films were investigated as a function of annealing temperature. The films were subjected to post annealing at different temperatures in the range of 350-650 °C in an air ambient. All the as grown and annealed films at temperature of 350 °C showed p-type conduction. The films lost p-type conduction after post annealing treatment temperature of above 350 °C, suggesting a narrow post annealing temperature window for the fabrication of p-type ZnO:Ag films. ZnO:Ag film annealed at 350 °C revealed lowest resistivity of 7.25 × 10⁻² Ω cm with hole concentration and mobility of 5.09 × 10¹⁹ cm⁻³ and 1.69 cm²/V s, respectively. Observation of a free-to-neutral-acceptor (e,A^o) and donor-acceptor-pair (DAP) emissions in the low temperature photoluminescence measurement confirms p-type conduction in the ZnO:Ag films.     

Electrodeposition of BixSb2−xTey thermoelectric thin films from nitric acid and hydrochloric acid systems

The electrochemical behaviors of Bi^III, Te^IV and Sb^III single ions and their mixtures were investigated in nitric acid and hydrochloric acid system separately. Based on which, Bi_xSb_2−xTe_y thermoelectric films were prepared by potentiostatic electrodeposition from the solutions with different concentrations of Bi^III, Te^IV and Sb^III in the two acid systems. The morphologies, compositions, structures, Seebeck coefficients and resistivities of the deposited thin films were characterized and compared by ESEM (or FESEM), EDS, XRD, Seebeck coefficient measurement system and four-probe resistivity measuring device respectively. The results show that although Bi_xSb_2−xTe_y thermoelectric thin film which structure is consistent with the standard pattern of Bi_0.5Sb_1.5Te₃ can be gained in both of the two acid solutions by adjusting the deposition potential, their morphologies and thermoelectric properties have big differences in different acid solutions.     

Influence of temperature annealing on optical properties of SrTiO3/BaTiO3 multilayered films on indium tin oxide

We have prepared SrTiO₃/BaTiO₃ thin films with multilayered structures deposited on indium tin oxide (ITO) coated glass by a sol-gel deposition and heating at 300-650 °C. The optical properties were obtained by UV-vis spectroscopy. The films show a high transmittance (approximately 85%) in the visible region. The optical band gap of the films is tunable in the 3.64-4.19 eV range by varying the annealing temperature. An abrupt decrease towards the bulk band gap value is observed at annealing temperatures above 600 °C. The multilayered film annealed at 650 ° C exhibited the maximum refractive index of 2.09-1.91 in the 450-750 nm wavelength range. The XRD and AFM results indicate that the films annealed above 600 ° C are substantially more crystalline than the films prepared at lower temperatures which were used to change their optical band gap and complex refractive index to an extent that depended on the annealing temperature.     

C-V studies on metal-ferroelectric bismuth vanadate (Bi2VO5.5)-semiconductor structure

Ferroelectric bismuth vanadate Bi₂VO_5.5 (BVO) thin films have been successfully grown on p-type Si(100) substrate by using chemical solution decomposition (CSD) technique followed by rapid thermal annealing (RTA). The crystalline nature of the films has been studied by X-ray diffraction (XRD). Atomic force microscopy (AFM) was used to study the microstructure of the films. The dielectric properties of the films were studied. The capacitance-voltage characteristics have been studied in metal-ferroelectric-insulator-semiconductor (MFIS) configuration. The dielectric constant of BVO thin films formed on Si(100) is about 146 measured at a frequency of 100 kHz at room temperature. The capacitance-voltage plot of a Bi₂VO_5.5 MFIS capacitor subjected to a dc polarizing voltages shows a memory window of 1.42 V during a sweep of ±5 V gate bias. The flatband voltage (V_f) shifts towards the positive direction rather than negative direction. This leads to the asymmetric behavior of the C-V curve and decrease in memory window. The oxide trap density at a ramp rate of 0.2 V/s was estimated to be as high as 1.45×10¹² cm⁻².