Co@N-石墨烯/C催化甲苯衍生物氧化胺化研究（英文）

核壳结构纳米催化剂的发展一直备受化学家的关注.我们通过热解碳担载乙酸钴和1,10-菲啰啉复合物制备出具有核壳结构的氮掺杂石墨烯包裹钴催化剂,并对其进行了系统的表征和催化性能研究.研究发现,该催化剂在TBHP和H_2共存的条件下,在催化硝基苯和甲苯的选择性还原-氧化胺化合成N-烷基化胺反应中展现出较好的催化性能和良好的官能团耐受性.透射电镜表征表明氧化钴纳米颗粒被厚度约1.12~1.87 nm的含氮石墨烯壳包裹.X射线光电子能谱表征发现壳层中的石墨烯氮和作为核的氧化钴纳米颗粒间具有较明显的相互作用.我们对催化体系的普适性以及反应机理也进行了较为系统的研究.     

包钯纳米颗粒的中空介孔硅铝酸盐纳米球的合成及其在多步催化反应和尺寸选择催化氢化中的应用

最近, 具有中空核壳结构的纳米材料在催化领域中有着深入的研究和广泛的应用. 在本文中, 我们使用一种简单易行的方法合成了一种包裹钯纳米颗粒的中空介孔硅铝酸盐纳米球(简写为Pd@HMAN). 首先, 通过一种先原位合成钯纳米粒子再对其进行二氧化硅包裹的方法, 在Brij56-环己烷-水的反相胶束中合成了具有核壳结构的包裹钯纳米颗粒的二氧化硅纳米球(简写为Pd@SiO₂). 然后, 使用CTAB, Na₂CO₃和NaAlO₂试剂, 通过简单的碱性条件下刻蚀Pd@SiO₂的过程, 我们成功得到了具有多孔性能的中空核壳型Pd@HMAN纳米催化剂. 由于硅铝酸盐外壳具有酸催化作用, 并且内核钯纳米颗粒又是一种高活性的催化媒介, 因此, 这种复合的多功能纳米催化剂能够很好的应用于多步催化反应中. 此外, 通过一个简单的热处理的方法, 能够缩小硅铝酸盐外壳上的孔道, 我们发现这种孔道调节后的Pd@HMAN纳米催化剂在尺寸选择性氢化反应中有很好的应用前景.     

氮掺杂还原氧化石墨烯/四氧化三钴双功能催化剂的制备及表征

采用尿素作为氮源,通过热退火法制备氮掺杂还原氧化石墨烯,然后以乙酰丙酮钴作为钴源通过水热法制备氮掺杂还原氧化石墨烯/四氧化三钴杂化纳米片作为催化氧还原和氧析出反应的双功能催化剂。利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线电子能谱仪(XPS)等对其进行形貌结构表征,通过旋转圆盘电极等电化学测试对其电催化性能进行分析,可以看出该催化剂具有良好的氧还原和氧析出催化性能。     

原位合成钴/还原氧化石墨烯纳米粒子催化氨硼烷制氢

采用简单的原位还原合成方法,利用具有温和还原性能的氨硼烷作为还原剂,在室温下一步还原氧化石墨烯和氯化钴混合溶液制备了还原氧化石墨烯负载钴纳米复合材料催化剂. 利用所制备的钴/还原氧化石墨烯催化剂催化氨硼烷水解制氢,发现钴/还原氧化石墨烯具有优异的催化性能. 相对于没有负载的钴纳米粒子以及采用硼氢化钠作为还原剂制备的钴/还原氧化石墨烯催化剂,采用氨硼烷还原制备的钴/还原氧化石墨烯催化剂表现出更加优越的催化性能. 动力学测试表明,钴/还原氧化石墨烯催化氨硼烷水解反应为零级反应,同时钴/还原氧化石墨烯催化剂催化氨硼烷水解反应的活化能为27.10 kJ·mol^-1,低于大部分已报道的其它催化剂,甚至一些贵金属催化剂的活化能. 钴/还原氧化石墨烯催化剂有着稳定的循环使用性,特别是其具有的磁性使得它能够直接从溶液中通过磁力回收,极具应用前景. 这种简单有效的合成方法有望推广到其它的金属-还原氧化石墨烯纳米复合材料体系.     

石墨烯负载的金属氧化物纳米颗粒的可控制备及催化性能

采用直接浸渍法、过氧化氢均相氧化沉积法和氨水催化水解法制备了石墨烯负载的铁、钴、镍金属氧化物纳米颗粒.研究了三种沉积方法对颗粒尺寸分布的影响;采用透射电子显微镜、傅里叶变换红外光谱、X射线衍射和X射线光电子能谱表征了催化剂的形貌与结构.用过氧化氢均相氧化沉淀法可制得粒径分布最均匀的纳米颗粒.过氧化氢的氧化作用可使石墨烯表面的氧化基团含量最大化,为纳米颗粒提供了足够的吸附与成核点.氨水加速了金属离子的水解与成核,导致纳米颗粒的粒径增大与不均.以苯甲醇氧化为探针反应考察了催化剂的性能.催化剂的活性按以下顺序逐渐下降:过氧化氢辅助沉积法>直接浸渍法>氨水催化水解法,与纳米颗粒尺寸增长趋势一致.纳米催化剂颗粒尺寸与其活性的良好关联性显示,发展石墨烯负载尺寸可控的纳米催化剂的方法具有重要意义.     

原位合成钴/还原氧化石墨烯纳米粒子催化氨硼烷制氢（英文）

采用简单的原位还原合成方法,利用具有温和还原性能的氨硼烷作为还原剂,在室温下一步还原氧化石墨烯和氯化钴混合溶液制备了还原氧化石墨烯负载钴纳米复合材料催化剂.利用所制备的钴/还原氧化石墨烯催化剂催化氨硼烷水解制氢,发现钴/还原氧化石墨烯具有优异的催化性能.相对于没有负载的钴纳米粒子以及采用硼氢化钠作为还原剂制备的钴/还原氧化石墨烯催化剂,采用氨硼烷还原制备的钴/还原氧化石墨烯催化剂表现出更加优越的催化性能.动力学测试表明,钴/还原氧化石墨烯催化氨硼烷水解反应为零级反应,同时钴/还原氧化石墨烯催化剂催化氨硼烷水解反应的活化能为27.10 kJ·mol-1,低于大部分已报道的其它催化剂,甚至一些贵金属催化剂的活化能.钴/还原氧化石墨烯催化剂有着稳定的循环使用性,特别是其具有的磁性使得它能够直接从溶液中通过磁力回收,极具应用前景.这种简单有效的合成方法有望推广到其它的金属-还原氧化石墨烯纳米复合材料体系.     

原位合成氮掺杂石墨烯负载钯纳米颗粒用于催化香兰素高选择性加氢反应

通过原位合成法制备了氮掺杂石墨烯负载钯纳米颗粒催化剂Pd@N/C-2,用于催化香兰素选择性加氢反应.采用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)等方法对Pd@N/C-2催化剂进行结构与性能的表征,分析表明石墨烯层在活性钯纳米颗粒表面起到了保护作用,提高了催化剂在反应条件下的稳定性,在五次循环回收实验后催化剂仍保持很高的反应活性.通过对石墨烯掺杂氮原子引入了催化反应的化学活性中心和金属纳米颗粒沉积的锚定中心,从而使石墨烯在加氢催化反应中的性能得到进一步提高.并且通过对溶剂的调控实现了香兰素分别高选择性生成香草醇和对甲基愈创木酚,在优化的反应条件下,香草醇和对甲基愈创木酚的产率分别为89%和99%.     

基于内嵌钴/氮掺杂多孔碳三维石墨烯笼的抗团聚高效氧还原电催化剂

氧还原反应是决定燃料电池、金属-空气电池等多种新型清洁能源存储与转化技术之性能与应用的关键反应. 铂及其合金是目前催化活性最好的氧还原反应催化剂,但其高昂的成本限制了规模化应用. 在小尺寸效应作用下,微纳米结构催化剂颗粒在电极制备与电化学反应过程中的团聚限制了催化剂本征催化活性的充分发挥. 本文基于喷雾热解技术,发展了一种基于内嵌钴/氮掺杂多孔碳三维石墨烯笼的高活性、抗团聚非贵金属氧还原反应催化剂. 此结构中,金属有机骨架化合物ZIF-67衍生的钴/氮掺杂多孔碳纳米结构是催化氧还原反应的活性中心,包覆其外的三维石墨烯笼不仅可在钴/氮掺杂碳纳米结构之间构建连续的三维载流子传导网络,且可高效抑制其在催化剂制备与电化学反应过程中的团聚与活性损失. 在碱性电解液中,此类非贵金属催化剂表现出可与铂基催化剂媲美的氧还原反应活性和优异的稳定性.     

核壳结构镍的制备及催化性能

利用软化学方法制备出了聚苯乙烯(PS)/镍核壳结构和纳米镍催化剂, 并利用SEM和XRD对材料的形貌和结构进行了表征. 将上述催化剂应用于亚甲基蓝染料加氢反应, 一步实现染料褪色和硼氢化钠水解制氢. 研究表明, 核壳结构极大地提高了镍的催化能力. 在相同条件下, 核壳结构镍的加氢催化效率是纳米镍的1.42倍, 产氢效率是纳米镍的4.76倍, 这说明核壳结构在催化领域具有一定的优势.     

超稳纳米金催化剂—走在实用化的路上

纳米金的催化性能受载体影响巨大,选择合适的载体或设计金属-载体界面精细结构能显著影响纳米金的催化性能.迄今发现各种载体包括酸、碱金属氧化物、碳材料以及有机聚合物均可作为纳米金的有效载体.相应的各种金催化剂均展现出独特的催化活性与选择性.一个典型的例子是核壳结构的Au/NiO催化剂,基于该催化剂催化异丁烯醛制备异丁烯酸甲酯的化工厂己于2008年开始兴建.金催化剂在AsH3气体传感器和汞收集器等环境分析方面也开始实际应用.因而,金催化剂的稳定性和使用寿命成为当前关注的焦点问题.目前报道的长寿命金催化剂典型例子有MINTEK催化剂和YD-3烟台催化剂,后者是由α-Fe2O3和La2O3改性氧化铝负载的金催化剂.中国科学院大连化学物理研究所张涛院士和王军虎研究员团队在近期研究中发现高温焙烧条件下Au纳米颗粒与羟基磷灰石(HAP)载体之间会发生金属-载体强相互作用(Strong Metal-Support Interaction简称SMSI)效应.SMSI效应导致载体对Au纳米颗粒形成包裹,可以有效提升Au纳米颗粒的抗烧结性能,但其对活性位的覆盖也会导致催化剂活性的下降.最近,该团队通过向载体HAP中添加TiO2进行修饰,成功设计开发出Au/HAP-TiO2催化剂.该催化剂上Au纳米颗粒与HAP接触的一侧被HAP薄层包裹,与TiO2接触的一侧裸露,呈现出独特的半包裹结构.通过这种纳米尺度的结构设计,该金催化剂经过8000℃的高温焙烧后不仅对一系列反应均表现出可观的催化活性和优异的抗烧结性能,且在模拟汽车尾气CO消除反应中表现出优于商业三效催化剂的反应稳定性.该工作为负载型纳米金催化剂的应用,特别是在高温催化反应中的实际应用提供了新途径,因此有望促进负载型金催化剂的实用化乃至商业化进程.     

One-pot synthesis to engineer a Co-KIT-6 catalyst for the ring opening of methylcyclopentane

Co-KIT-6 mesoporous materials with Ia3d symmetry and Si/Co ratios of 50, 25, and 10 were prepared using hydrothermal one-pot synthesis. The Co-KIT-6 mesoporous materials were characterized by X-ray diffraction, N₂ adsorption–desorption isotherms, scanning electron microscopy, transmission electron microscopy, Fourier transform infrared, and X-ray photoelectron spectroscopy. The physicochemical characterization results show that all of the samples have well-ordered cubic mesostructures and that the structural integrity is preserved for n_Si/n_Co ratios as high as 10. It was found that most of the cobalt ions exist as isolated framework species, but for Co-KIT-6 with an n_Si/n_Co ratio of 10, the presence of extra-framework species/small cobalt oxide clusters cannot be excluded. The ability of these catalysts was tested by examining the conversion of the reaction of methylcyclopentane with hydrogen at atmospheric pressure and temperatures between 200 and 450 °C. The catalytic results show that their catalytic activity increases significantly with increasing cobalt content. The active sites, tetrahedrally coordinated Co and isolated atomic Co sites, were responsible for the endocyclic CC bond rupture between substituted secondary–tertiary carbon atoms, whereas the small clusters serve as active sites for the successive CC bond rupture. The ring-opening selectivity can be improved by increasing the density of isolated cobalt atom sites at low reaction temperatures.     

Preparation of MnCo/MCM-41 catalysts with high performance for chlorobenzene combustion

MCM-41 was synthesized by a soft template technique. The specific surface area and pore volume of the MCM-41 were 805.9 m²/g and 0.795 cm³/g, respectively. MCM-41-supported manganese and cobalt oxide catalysts were prepared by an impregnation method. The energy dispersive X-ray spectroscopy clearly confirmed the existence of Mn, Co, and O, which indicated the successful loading of the active components on the surface of MCM-41. The structure and function of the catalysts were changed by modulating the molar ratio of manganese to cobalt. The 10%MnCo(6:1)/MCM-41 (Mn/Co molar ratio is 6:1) catalyst displayed the best catalytic activity according to the activity evaluation experiments, and chlorobenzene (1000 ppm) was totally decomposed at 270 °C. The high activity correlated with a high dispersion of the oxides and was attributed to the exposure of more active sites, which was demonstrated by X-ray diffraction and high-resolution transmission electron microscopy. The strong interactions between MnO₂, Co₃O₄, MnCoO_x, and MCM-41 indicated that cobalt promoted the redox cycles of the manganese system. The bimetal-oxide-based catalyst showed better catalytic activity than that of the single metal oxide catalysts, which was further confirmed by H₂ temperature-programmed reduction. Chlorobenzene temperature-programmed desorption results showed that 10%MnCo(6:1)/MCM-41 had higher adsorption strength for chlorobenzene than that of single metal catalysts. And stronger adsorption was beneficial for combustion of chlorobenzene. Furthermore, 10%MnCo(6:1)/MCM-41 was not deactivated during a continuous reaction for 1000 h at 260 °C and displayed good resistance to water and benzene, which indicated that the catalyst could be used in a wide range of applications.     

介孔氧化铝负载Ni-Co氧化物催化剂上丙烷氧化脱氢制丙烯

以非离子型三嵌段共聚物作为模板剂, 异丙醇铝为氧化铝的前驱物, 采用一锅法合成了一系列介孔氧化铝负载镍氧化物、钴氧化物以及镍-钴双金属氧化物催化剂, 并以介孔氧化铝为载体, 采用浸渍法制备了负载Ni-Co 氧化物催化剂. 采用N₂吸附-脱附、高分辨透射电镜(HRTEM)、X射线粉末衍射(XRD)、H₂程序升温还原(H₂-TPR)以及激光拉曼光谱(LRS)等技术对催化剂的结构与性质进行表征, 并考察了催化剂的丙烷氧化脱氢反应性能. 结果表明: 一锅法制备的各催化剂均有大的比表面积和规整的孔道结构, 且负载的金属氧化物高度分散; 而浸渍法制备的催化剂, 其载体的介孔结构被破坏并有Co₃O₄晶相生成. 在考察的催化剂中, 一锅法合成的介孔氧化铝负载Ni-Co 氧化物催化剂表现出最佳的丙烷氧化脱氢性能. 在450 °C、C₃H₈:O₂:N₂的摩尔比为1:1:4和空速(GHSV)为10000 mL·g^-1·h^-1条件下, 该催化剂上丙烯产率为10.3%, 远高于浸渍法制备的催化剂上所获得的丙烯产率(2.4%). 关联催化剂表征和反应结果, 讨论了催化剂结构与性能之间的关系.     

Effect of cobalt weight content on the structure and catalytic properties of Co/CNT catalysts in the fischer–tropsch synthesis

Cobalt-based Fischer–Tropsch synthesis (FTS) catalysts containing 1 to 40 wt % cobalt supported on multi-walled carbon nanotubes (CNTs) have been investigated. The CNTs have been characterized by low-temperature nitrogen adsorption, scanning electron microscopy, and X-ray photoelectron spectroscopy. All catalysts have been prepared by impregnating, with an ethanolic solution of cobalt nitrate, the CNTs preoxidized with concentrated nitric acid and have been tested in the FTS at 220°C and atmospheric pressure. Correlations have been established between the cobalt weight content of the catalyst and the Co particle size determined by transmission electron microscopy and X-ray diffraction. The Co content and particle size have an effect on the activity and selectivity of the catalyst and on the target fraction (C₅₊) yield in the FTS. The highest CO conversion is observed for the catalyst containing 20 wt % Co; the highest selectivity and activity, for the catalyst containing 5 wt % Co; the highest C₅₊ yield, for the catalyst containing 10 wt % Co.     

Co/Ce0.5Zr0.5O2催化剂的制备及甲烷部分氧化制合成气

利用共沉淀法制备了具有介孔结构的Ce_0.5Zr_0.5O₂固溶体载体,然后浸渍不同质量分数(10%、20%、30%)的活性组分钴,制备了系列Co/Ce_0.5Zr_0.5O₂催化剂。利用N₂物理吸附(BET)、X射线粉末衍射(XRD)、H₂-程序升温还原(H₂-TPR)、扫描电子显微镜(SEM) 、透射电子显微镜(TEM) 、 程序升温氧化(TPO)和热重(TG)等手段对制备和反应后的催化剂进行了表征,研究了它们对甲烷部分氧化制合成气反应的催化性能。研究结果表明,铈锆固溶体负载的钴比较容易被还原,该系列催化剂具有较高的活性和对H₂及CO的选择性,且随Co含量的增加,催化剂的活性和对H₂和CO的选择性得到提高的同时,也增强了催化剂的抗积炭性能。     

Cobalt Single‐Atom Catalysts with High Stability for Selective Dehydrogenation of Formic Acid

Metal–organic framework (MOF)‐derived Co‐N‐C catalysts with isolated single cobalt atoms have been synthesized and compared with cobalt nanoparticles for formic acid dehydrogenation. The atomically dispersed Co‐N‐C catalyst achieves superior activity, better acid resistance, and improved long‐term stability compared with nanoparticles synthesized by a similar route. High‐angle annular dark‐field–scanning transmission electron microscopy, X‐ray photoelectron spectroscopy, electron paramagnetic resonance, and X‐ray absorption fine structure characterizations reveal the formation of Co^IIN_x centers as active sites. The optimal low‐cost catalyst is a promising candidate for liquid H₂ generation.     

水热合成Co3O4的制备参数调变及其催化分解N2O性能

以十六烷基三甲基溴化胺（CTAB）为模板剂,通过调变CTAB浓度水热合成了氧化钴前驱体,焙烧制得棒状形貌的Co₃O₄,在其表面浸渍K₂CO₃溶液制得K改性的Co₃O₄催化剂,用于N₂O分解。用X射线衍射（XRD）、N₂物理吸附（BET）、扫描电镜（SEM）、X射线光电子能谱（XPS）、H₂程序升温还原（H₂-TPR）和O₂程序升温脱附（O₂-TPD）等技术对催化剂进行了表征,考察了CTAB/钴及尿素/钴物质的量比等制备参数对Co₃O₄催化分解N₂O活性的影响。结果表明,CTAB浓度为0.05 mol/L、CTAB/钴离子物质的量比为1、尿素/钴离子物质的量比为4时,所制备的Co₃O₄催化剂具有较高的N₂O分解活性,而K改性可以进一步提升其催化性能。K改性的Co₃O₄在有氧有水气氛中400℃下进行N₂O分解反应,50 h后N₂O转化率仍保持在91%以上。     

Hydrothermal synthesis of cobalt carbonates using different counter ions: An efficient precursor to nano-sized cobalt oxide (Co3O4)

Synthesis of submicrometer crystalline particles of cobalt carbonate was achieved hydrothermally using different cobalt salts and urea with a molar ratio from 1:3 to 1:20 (cobalt salt:urea) in aqueous solutions at 160 °C for 24-36 h, in the presence of cetyltrimethylammonium bromide (CTAB) as a surfactant. Nanoparticles of Co₃O₄, with an average size from 30 to 39 nm, were obtained by thermal decomposition of CoCO₃ samples at 500 °C for 3 h in an electrical furnace. The as-synthesized products were characterized by powder X-ray diffraction (XRD), Fourier transform infrared spectra (FT-IR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), UV-Vis spectra and thermal analysis. Studying the optical properties of the as-prepared cobalt oxide nanoparticles showed the presence of two band gaps, the values of which confirmed the semiconducting properties of the prepared Co₃O₄.     

负载型钌催化剂催化山梨醇氢解制乙二醇(英)

Supported Ru catalysts were prepared by wet impregnation to evaluate the role of different oxide supports（Al₂O₃,SiO₂,TiO₂,ZrO₂） in sorbitol hydrogenolysis to glycols.X-ray diffraction,transmission electron microscopy,hydrogen chemisorption,X-ray photoelectron spectroscopy,and NH3temperature-programmed desorption were used to characterize the catalysts,which were active in the hydrogenolysis of sorbitol.The support affected both the physicochemical properties and catalytic behavior of the supported Ru particles.The characterization results revealed that the Ru/Al₂O₃catalyst has a high surface acidity,partially oxidized Ru species on the surface,and a higher surface Ru/Al atomic ratio,which gave it the highest selectivity and yield to glycols.     

Facile Synthesis of AuPd Nanochain Networks on Carbon Supports and Their Application as Electrocatalysts for Oxygen Reduction Reaction

The present work reports the facile synthesis and characterization of carbon‐supported porous Pd shell coated Au nanochain networks (AuPdNNs/C). By using Co nanoframes as sacrificial templates, AuPdNNs/C series have been prepared by a two‐step galvanic replacement reaction (GRR) technique. In the first step, the Au metal precursor, HAuCl₄, reacts spontaneously with the formed Co nanoframes through the GRR, resulting in Au nanochain networks (AuNNs). The second GRR is performed with various concentrations of Pd precursor (0.1, 1, and 10 mM PdCl₂), resulting in AuPdNNs/C. The synthesized AuPdNNs/C series are investigated as electrocatalysts for oxygen reduction reaction (ORR) in alkaline solution. The physical properties of the AuPdNNs/C catalysts are characterized by scanning electron microscopy (SEM), high‐resolution transmission electron microscopy (HRTEM), UV‐vis absorption spectroscopy, and cyclic voltammetry (CV). Rotating disk electrode (RDE) voltammetric studies show that the Au_0.8Pd_0.2NNs/C (prepared using 1 mM PdCl₂) has the highest ORR activity among all the AuPdNNs/C series, which is comparable to commercial Pt catalyst (E‐TEK). The ORR activity of AuPdNNs/C is presumably due to the enhanced Pd surface area and high porosity of Pd nanoshells.