Effect of silica content on thermal stability of fumed silica/epoxy composites

Composites of a fumed silica industrial residue and an epoxy resin were prepared and their thermal stability and thermal degradation behaviour were studied by TGA in air. Classical thermal stability parameters, based on the initial decomposition temperature (IDT), temperature of maximum rate of mass loss (T_max) and integral procedure decomposition temperature (IPDT) were calculated before and after subtraction of the filler mass from the TGA curves. Without filler mass subtraction, the thermal stability of the epoxy resin seems to be improved and the mass loss rate was reduced by the addition of fumed silica. Nevertheless, after subtraction of the filler mass, the thermal degradation behaviour of the resin was only slightly affected by the silica content. A possible negative effect of the silica content on the cure was also found.     

Enhancing mechanical and thermal properties of PLLA ligaments with fumed silica nanoparticles and montmorillonite

Nanocomposites of poly(l-lactic acid) (PLLA) containing 2.5 wt% of fumed silica nanoparticles (SiO₂) and organically modified montmorillonite (OMMT) were prepared by solved evaporation method. From SEM micrographs it was observed that both nanoparticles were well dispersed into PLLA matrix. All nanocomposites exhibited higher mechanical properties compared to neat PLLA, except elongation at break, indicating that nanoparticles can act as efficient reinforcing agents. Nanoparticles affect, also, the thermal properties of PLLA and especially the crystallization rate, which in all nanocomposites is faster than that of neat PLLA. From the thermogravimetric curves it can be seen that neat PLLA nanocomposites present a relatively better thermostability than PLLA, and this was also verified from the calculation of activation energy (E). From the variation of E with increasing degree of conversion it was found that PLLA/nanocomposites decomposition takes place with a complex reaction mechanism, with the participation of two different mechanisms. The combination of models, nth order and nth order with autocatalysis (Fn–Cn), for PLLA and PLLA/OMMT as well as the combination of Fn–Fn for PLLA/SiO₂ give the better results. For the PLLA/OMMT the values of the E for both mechanisms are higher than neat PLLA. For the PLLA/SiO₂ nanocomposite the value of the E is higher than the corresponding value for PLLA, for the first area of mass loss, while the E of the second mechanism has a lower value.     

The effect of opacifier properties on thermal conductivity of vacuum insulation panel with fumed silica

Journal of Thermal Analysis and Calorimetry - The reduction of radiation heat transfer in VIPs is an important issue. In VIPs, the radiation heat transfer is reduced by the use of opacifier....     

Surface grafting of glycidyl methacrylate on silica gel and polyethylene beads

Surface grafting of glycidyl methacrylate (GMA) on silica gel and a polyethylene bead was performed by radical polymerization and radiation-induced polymerization, respectively, in order to improve softness. Subsequently, diethylene triamine (DETA), triethylene tetraamine (TETA), and iminodiacetic acid (IDA) were introduced to the grafted GMA for use as affinity columns. The efficiency of the affinity column was investigated by use of bovine serum albumin (BSA) and hemoglobin (Hb) as model proteins. The affinity degree of BSA was higher than Hb for the DETA and TETA column, whereas the affinity degree of Hb was higher than BSA for the IDA column supported by silica gel. The affinity degree of BSA was higher than Hb for the DETA and TTA column supported by polyethylene (PE) beads.     

Comparative characterization of polymethylsiloxane hydrogel and silylated fumed silica and silica gel

Polymethylsiloxane (PMS) hydrogel (C(PMS)=10 wt%, soft paste-like hydrogel), diluted aqueous suspensions, and dried/wetted xerogel (powder) were studied in comparison with suspensions and dry powders of unmodified and silylated nanosilicas and silica gels using (1)H NMR, thermally stimulated depolarization current (TSDC), quasielastic light scattering (QELS), rheometry, and adsorption methods. Nanosized primary PMS particles, which are softer and less dense than silica ones because of the presence of CH(3) groups attached to each Si atom and residual silanols, form soft secondary particles (soft paste-like hydrogel) that can be completely decomposed to nanoparticles with sizes smaller than 10 nm on sonication of the aqueous suspensions. Despite the soft character of the secondary particles, the aqueous suspensions of PMS are characterized by a higher viscosity (at concentration C(PMS)=3-5 wt%) than the suspension of fumed silica at a higher concentration. Three types of structured water are observed in dry PMS xerogel (adsorbed water of 3 wt%). These structures, characterized by the chemical shift of the proton resonance at delta(H) approximately 1.7,3.7, and 5 ppm, correspond to weakly associated but strongly bound water and to strongly associated but weakly or strongly bound waters, respectively. NMR cryoporometry and QELS results suggest that PMS is a mesoporous-macroporous material with the textural porosity caused by voids between primary particles forming aggregates and agglomerates of aggregates. PMS is characterized by a much smaller adsorption capacity with respect to proteins (gelatin, ovalbumin) than unmodified fumed silica A-300.     

Wettability of silane films on silica fillers

Colloid and Polymer Science - Heats of immersion in waterH i W and in benzeneH i B (in joules per gramme) of four silica fillers, modified by some silane coupling agents capable of forming...     

Dispersion stabilities and rheological properties of fumed silica suspensions

Herein, we have reviewed fumed silica suspensions in dispersing fluids, polymer melts, and polymer solutions, focusing on their dispersion stability and rheological properties as a function of the surface character of fumed silica powders and the silica volume fraction, ?. Hydrophilic fumed silica powders are well dispersed at ? < 0.01 in polar dispersing fluids or polar polymer melts, and their phase states change from sol to gel with increasing ?. Such changes should also be strongly related to the rheological responses of the hydrophilic fumed silica suspensions, which change from Newtonian flow behavior to gel-like elasticity with increasing ?. On the other hand, hydrophobic fumed silica powders are stabilized in both polar and nonpolar dispersing fluids, depending on the interactions between the surface hydrophobic moieties and the dispersing fluids, in addition to those between the residual surface silanol groups and dispersing fluid, except for the particle–particle interactions. Moreover, the effects of the adsorption and desorption of polymers, as well as of non-adsorbing polymers on the dispersion stability and rheological behavior of fumed silica suspensions are discussed, by taking account of their optical microscopic observation and SANS curves.     

Rheological behavior of fumed silica filled polyethylene oxide

Influence of molecular weight of polymer matrix on nanocomposites rheology is not yet well understood. Herein dynamic rheological responses of fumed silica (FS)/polyethylene oxide (PEO) nanocomposites are investigated as a function of viscosity‐averaged molecular weight (M_η) of PEO, volume fraction (?) and surface characteristics (hydrophilic or hydrophobic) of FS. In the nanocomposites, FS does not influence the glass transition and crystallinity of PEO in the mobile PEO phase while the interfacial interactions tend to immobilize a small fraction of PEO chains that could not undergo glass transition. In spite of the common observation that the reinforcement decreases with increasing M_η of PEO and improving hydrophobicity of FS, linear rheological responses are well reproduced by the two‐phase model, revealing the crucial contribution of the non‐Newtonian matrix undergoing microscopic strain amplified by the filler. Furthermore, nonlinear rheological responses of the nanocomposites are collapsed into master curves plotted against local strain of the matrix. Analyzing the nonlinear rheology by Fourier transform and stress waveform methods reveal the dominating contribution of the matrix and the role of strain amplification played by the filler. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 397–405     

Preparation, characterization and biodegradation of biopolymer nanocomposites based on fumed silica

PLA and PCL based nanocomposites prepared by adding three different types of fumed silica were obtained by melt blending. Materials were characterized by means of Scanning Electron Microscopy (SEM), Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA) and Dynamic–Mechanical Thermal Analysis (DMTA).A good distribution of the fumed silica into both polymer matrices was observed. The highest thermo-mechanical improvements were reached by addition of the fumed silica with higher surface area. PLA and its nanocomposites were degraded in compost at 58 °C; at this temperature all samples presented a significant level of polymer degradation, but a certain protection action of silica towards PLA degradation was observed, whereas the addition of fumed silica did not show considerable influence on the degradation trend of PCL. These dissimilarities were attributed to the different degradation mechanism of the two polymers.     

Effect of resin infiltration on fumed silica-based thermal insulations

The thermal conductivities and the strengths of fumed silica-based thermal insulations prepared by the dry process and the resin infiltration method have been studied. Infiltration of the insulation samples prepared by dry processing of mixtures, consisting of fumed silica, ceramic fiber and a SiC opacifier, was performed to strengthen their binding structure. The high temperature thermal conductivities for the insulation samples obtained by the resin infiltration method were similar to those for the samples prepared by the dry process. On the other hand, the bending strengths for the former were superior to those for the latter. However, the resin-infiltrated samples were more brittle than the samples obtained by the dry process due to the occurrence of rigid bonding between the fibers and the infiltrated resin in the porous insulations. The thermosetting resin solution infiltration method appeared to be applicable to producing a dust-free fumed silica-based thermal insulation.     

Tailored rheology of a metallocene polyolefin through silane grafting and subsequent silane crosslinking

Polymer modification through silane grafting and its subsequent crosslinking allows the rheological properties of a polymer to be tuned from those of a viscous melt to those of a crosslinked elastic network. In this study, a metallocene polyolefin resin is grafted with vinyl trimethoxy silane (VTMS) using dicumyl peroxide (DCP) as the initiator and is subsequently crosslinked in an oxidative environment. Dynamic rheological experiments are conducted to elucidate the effects of DCP and VTMS concentrations on the grafting and ensuing crosslinking processes. We find that the addition of VTMS alone to the polymer produces no grafting. In contrast, the presence of DCP by itself leads to direct crosslinking between polymer chains as suggested by an increase in elastic modulus and complex viscosity. Samples containing both DCP and VTMS undergo silane grafting, with the extent of grafting increasing with increasing DCP concentration. This conclusion is borne out by both rheological and Fourier transform infrared measurements. The grafted samples undergo silane crosslinking only in an oxidative environment and at temperatures equal to or greater than 190 °C. During crosslinking, the samples undergo a transition from a viscous melt with frequency‐dependent moduli to a gel exhibiting frequency‐independent moduli with the elastic modulus exceeding the viscous modulus. However, the kinetics of crosslinking and the extent of the modulus increase are a function of the DCP concentration, with both exhibiting a maximum at a specific DCP and VTMS combination. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2468–2479, 2000     

Fumed silica synthesis. Influence of hydrogen chloride on the fumed silica particle formation process

Interaction of silicon dioxide molecule up to the small silica protoparticle and primary particle formation, and influence of hydrogen chloride (HCl), water (H₂O) and inert molecules (nitrogen N₂) “under flame condition” and “after cooling” on structure and properties of fumed silica were investigated by quantum-chemical simulations. An attempt to give definition of surface concept on atomic level was made.     

Three-phase cyanate ester composites with fumed silica and negative-CTE reinforcements

Three-phase cyanate ester adhesives have been developed using a bisphenol E cyanate ester resin, fumed silica, and negative-CTE (coefficient of thermal expansion) reinforcements: short carbon fiber or zirconium tungstate (ZrW₂O ₈ ). Fumed silica was used to impart thixotropic behavior on the resin and decrease settling in the adhesives. The cured composites were evaluated using various thermal analysis techniques for their thermal-mechanical properties. Composites with short carbon fiber showed enhanced modulus and decreased thermal expansion (70% reduction for 20 vol%) and showed little phase separation. While settling of the dense ceramic particles could not be completely eliminated for the zirconium tungstate composites through rheological modification of the adhesive with added fumed silica, a reduction in CTE of 84% was achieved in the composite (58 vol%) compared to the neat resin. In addition, the effect of thermal history on the cure and temperature induced ZrW₂O₈ phase transitions, and their corresponding influence on thermal strains vs. temperature, are examined by thermomechanical analysis.     

Characterization of the interaction of poly(ethylene oxide) with nanosize fumed silica: Surface effects on crystallization

Poly(ethylene oxide) (PEO) of 4600 molar mass (PEO‐4600) was crystallized from methanol in the presence of hydrophilic fumed silicas (A380, A200, and OX50) with nominal surface areas of 380, 200, and 50 m²/g and a hydrophobic fumed silica (R812s) modified with methyl groups. The composites were characterized by thermogravimetric analysis and differential scanning calorimetry. The inhibition of crystallization and the tendency for chain reorganization after melting were in the order of A380 > A200 > OX50 > R812s, respectively, that is, both were least for the hydrophobic silica and increased with increasing specific surface area for the hydrophilic silica. The interaction of PEO with the silica increased in the melt state as compared with the solution‐cast samples, resulting in enhanced suppression of crystallization. The following took place at a high silica content: (1) crystallization occurred at crystallization temperatures [T_c < T_c (bulk)], suggesting that the silica inhibited crystallization; (2) crystallites with melt temperatures [T_m < T_m (bulk)] were observed, indictive of smaller and/or less perfect crystals; and (3) melt entropies [ΔS_m (surface) < ΔS_m (bulk)] suggested that the interaction of surface silanols, Si_sOH, with PEO decreased both the melt entropy and crystallite size/perfection. Crystallinity was observed in solution‐cast composites when there were greater than ～0.03 PEO molecules/nm² for native and ～0.01 PEO molecules/nm² for methylated fumed silica, similar to reported plateau equilibrium adsorption values from methanol. These results were consistent with a model in which PEO interacted more strongly with native fumed silica as compared with hydrophobically modified silica because of hydrogen bonding of the ether oxygens of PEO with the acidic silanols, preventing chain mobility and crystallization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1978–1993, 2003     

气相白炭黑表面处理率的影响因素及判定

气相白炭黑是一种二氧化硅纳米材料，气相白炭黑的最主要应用是用于硅橡胶的补强，但气相白炭黑在硅橡胶中很难分散，影响了补强效果，本文用六甲基二硅氮烷对白炭黑进行表面处理并对白炭黑表面处理率问题做一些探讨。     

Surface electric and titration behaviour of fumed oxides

Adsorption of Pb(II), Sr(II), and Cs(I) on fumed silica, alumina, titania, silica/titania (ST), silica/alumina (SA), and alumina/silica/titania (AST) reveals that mixed oxides containing titania have a greater adsorptive capability in respect to metal cations than individual and SA oxides. Pyrocarbon deposits on fumed oxides enhance the adsorption of metal ions. Calculations of electrophoretic potential (ζ) with consideration for the porosity of aggregates of primary particles of AST show a significant influence of surface alumina (at pH<8) and titania and silica (at pH>8) on the ζ values. The effective diameter of particles (D_ef) of fumed oxides in aqueous media depends on pH for AST stronger than for ST (between isoelectric points (IEPs) of titania and alumina). A significant difference in the pH values of IEP and point of zero charge is observed for AST samples. A pyrocarbon influence on the ζ potential depends on the type of oxide matrix, since ζ increases for certain samples but for others it decreases. These changes depend nonlinearly on pH as well as the secondary particle size distributions (SPSDs) and D_ef.     

Surface structure and properties of mixed fumed oxides

A variety of fumed oxides such as silica, alumina, titania, silica/alumina (SA), silica/titania (ST), and alumina/silica/titania (AST) were characterized. These oxides have different specific surface areas and different primary particle composition in the bulk and at the surface. These materials were studied by FTIR, NMR, Auger electron spectroscopy, one-pass temperature-programmed desorption with mass spectrometry control (OP TPDMS), microcalorimetry, and nitrogen adsorption. Nonlinear changes in the surface content of alumina in SA and AST and titania in ST and AST samples with increasing oxide content along with simultaneous changes in their specific surface area cause complex dependencies of the heat of immersion in water and desorption of water on heating on the structural parameters. Simultaneous analysis of changes in the surface phase composition, in the concentration of hydroxyls, and in the structural characteristics reveals that at a low content of the second phase the structural characteristics (e.g., S(BET)) are predominant; however, at a large content of these oxides the phase composition plays a more important role.     

Synergistic effect between POSS and fumed silica on thermal stabilities and mechanical properties of room temperature vulcanized (RTV) silicone rubbers

In this paper, both divinyl-hexa[(trimethoxysilyl)ethyl]-POSS (DVPS) and fumed silica were firstly introduced into polydimethylsiloxane (PDMS) system using as the cross-linker and the reinforcing filler respectively. And a series of novel RTV silicone rubbers synergistically enhanced by DVPS and fumed silica were prepared. The cross-linked networks in the novel RTV silicone rubbers have been studied by attenuated total reflection infrared spectroscopy, and the dispersions of POSS and fumed silica in these novel RTV silicone rubbers have been observed by means of scanning electron microscope (SEM). And thermal stabilities, thermo-oxidative stabilities and mechanical properties of these novel RTV silicone rubbers were studied by means of thermal gravimetric analysis and universal tensile testing machine, respectively. From the obtained results, it was found that synergistic effect between POSS-rich areas and fumed silica on thermal stability and mechanical property of RTV silicone rubber indeed existed. And the experimental results also exhibited that the thermal stabilities and mechanical properties of the novel RTV silicone rubbers were far better than those of the reference materials (DVPR and MTFR). The striking enhancements in thermal properties and improvements on mechanical properties of novel RTV silicone rubbers were likely attributed to the synergistic effect between POSS-rich domains and fumed silica. Meanwhile, it was found that the mechanical properties of RTV silicone rubbers prepared with a given amount of POSS cross-linker were enhanced with the increment of the loading amount of fumed silica.     

Filler-elastomer interactions: influence of silane coupling agent on crosslink density and thermal stability of silica/rubber composites

In this work, the crosslink density and thermal stability of the silica/rubber composites treated by silane coupling agents, i.e., gamma-aminopropyl triethoxysilane (APS), gamma-chloropropyl trimethoxysilane (CPS), and gamma-methacryloxypropyl trimethoxysilane (MPS), were investigated. The chemical structures of modified silicas were studied in term of solid-state 29Si NMR spectroscopy. The crosslink density of the composites was determined by swelling measurement. The development of organic functional groups on silica surfaces treated by coupling agents led to an increase in the crosslink density of the composites, resulting in increasing final thermal stability of the composites. The composites treated by MPS showed the superior crosslink density and thermal stability in these systems. The results could be explained by the fact that the organic functional groups of silica surfaces by silane surface treatments led to an increase of the adhesion at interfaces between silicas and the rubber matrix.     

Interaction of poly(ethylene oxide) with fumed silica

Interaction of poly(ethylene oxide) (PEO, 600 kDa) with fumed silica A-300 (SBET = 316 m2/g) was investigated under different conditions using adsorption, infrared (IR), thermal analysis (TG-DTA), AFM, and quantum chemical methods. The studied dried silica/PEO samples were also carbonized in a flow reactor at 773 K. The structural characteristics of fumed silica, PEO/silica, and pyrocarbon/fumed silica were investigated using nitrogen adsorption-desorption at 77.4 K. PEO adsorption isotherm depicts a high affinity of PEO to the fumed silica surface in aqueous medium. PEO adsorbed in the amount of 50 mg per gram of silica (PEO monolayer corresponds to CPEO approximately 190 mg/g) can disturb approximately 70% of isolated surface silanols. However, at the monolayer coverage, only 20% of oxygen atoms of PEO molecules take part in the hydrogen bonding with the surface silanols. An increase in the PEO amount adsorbed on fumed silica leads to a diminution of the specific surface area and contributions of micro- (pore radius R < 1 nm) and mesopores (1 < R < 25 nm) to the pore volume but contribution of macropores (R > 25 nm) increases with CPEO. Quantum chemical calculations of a complex of a PEO fragment with a tripple bond SiOH group of a silica cluster in the gas phase and with consideration for the solvent (water) effect show a reduction of interaction energy in the aqueous medium. However, the complex remains strong enough to provide durability of the PEO adsorption complexes on fumed silica; i.e., PEO/fumed silica nanocomposites could be stable in both gaseous and liquid media.