超临界二氧化碳对不同聚合方法制备的交联聚合物微球的塑化研究

采用分散聚合和无皂乳液聚合的方法,我们制备了粒径不同的交联聚合物微球。通过改变超临界二氧化碳的压力、处理微球的时间以及实验的温度,我们可以实现对这些微球塑化程度的调节。研究发现,随着超临界二氧化碳压力的升高,其对聚合物微球的塑化能力呈现出先增强后降低的趋势。文中我们对这种现象出现的机理也进行了相应的讨论。随着体系温度的升高或者延长处理微球的时间,超临界二氧化碳对两种微球的塑化能力都呈增强趋势。由于乳液聚合得到的聚合物的分子量通常会比分散聚合得到的聚合物的分子量大,因此在相同的条件下超临界二氧化碳对分散聚合法制备的微球塑化能力更强。     

表面富含羧基的单分散交联聚合物微球的快速自组装制备胶体晶的研究

在20～70℃范围内,用垂直沉积的方法可使表面富含羧基的单分散交联聚合物微球在不同的基底上快速自组装成三维有序的胶体晶.不同粒径的微球形成的胶体晶其光禁带峰位不同,因此可调控不同波长的光在胶体晶中的传播.利用紫外-可见光谱研究了胶体晶的光禁带峰位与组成其微球粒径之间的关系.结果表明,随着构成胶体晶微球粒径的增大,胶体晶光禁带峰位发生了红移,而随着入射光角度的增大,胶体晶的光禁带峰位发生了蓝移.利用原子力显微镜和扫描电子显微镜研究了其它条件对聚合物微球有序排列的影响,发现聚合物微球在pH值为3.0～13.0范围内可以形成三维有序自组装胶体晶.这是由于在不同的pH值下,聚合物微球表面发生羧基化及去羧基化反应,导致在自组装过程中微球之间和微球与介质之间作用力的变化     

由乙烯高效催化聚合而得的超高分子量聚乙烯的研究

本工作系研究以高效催化聚合获得的超高分子量聚乙烯的结构和性能。用扫描电子显微镜观察了高效催化剂及初生聚乙烯的形态。透射电子显微镜观察了初生聚乙烯粉未,发现毛遂边缘的超分子原纤维状织态结构。用偏光显微镜观察了不同分子量聚乙烯粉末的熔融和冷却结晶过程,生成的球晶随分子量增大而增大。用X-射线衍射、差热分析、倒换气相色谱测定了初生聚乙烯的结晶度随分子量而增大;用X-射线衍射、差热分析及密度梯度法测定经退火或热压制的聚乙烯样品的结晶度均随分子量增大而下降。X-射线衍射测定其晶粒尺寸亦随分子量增大而减小。差热分析和倒换气相色谱测定超高分子量聚乙烯粉末的结晶熔点温度(T_m)要比普通分子量聚乙烯高8-12℃。不同分子量聚乙烯的热形变曲线表明,超高分子量聚乙烯在熔融温度后出现明显的橡胶态。此外,还用差热与热重分析研究了超高分子量聚乙烯的热老化行为。测定了超高分子量聚乙烯的优异抗冲强度和沙浆磨耗量。并用扫描电镜对比观察了常规分子量和超高分子量聚乙烯试样的冲击断面的织态结构。     

聚乙二醇双丙烯酸酯在超临界二氧化碳中的光聚合研究

探索了聚乙二醇双丙烯酸酯在超临界二氧化碳中发生光聚合反应制备聚合物颗粒的过程.方法为向充满超临界二氧化碳的高压反应釜中,同时喷射二氧化碳与聚乙二醇双丙烯酸酯及光引发剂的溶液,溶液与二氧化碳形成均匀的喷雾并进一步通过反溶剂作用与超临界二氧化碳形成分散体系,当同步进行紫外光照射时,单体可以在超临界二氧化碳中发生光聚合.结果证明此方法是可行的,得到了聚合物微颗粒.研究了不同溶剂及反应原料用量对产物粒径分布的影响.采用不同溶剂,将改变反应原料及产物在超临界二氧化碳中的溶解度,进而改变产物的粒径分布;反应原料用量增加,其在超临界二氧化碳中的溶解度减小,导致产物粒径分布较宽。     

聚氧乙烯球晶上彩色环状条纹的形成

用自然白光代替偏振光在显微镜下观察聚氧乙烯球晶的生长过程, 可以更清晰地看到彩色环形条纹的形成. 当成长中的二维球晶相互碰撞后, 被挤出的熔体改变球晶的原有结晶方向, 流向饼形球晶中央而在其表面上逆向结晶, 由于被挤出的熔体数量有限, 晶层的厚度逐渐减小, 在盖玻片下方形成一个盘状的楔形真空间隙. 此间隙导致彩色环状干涉条纹的形成. 实验用肉眼直接观察到二维球晶在生长过程中结晶方式的变化, 为二次结晶理论的发展提供了实验依据.     

高压结晶PET/PC共混体系中生长在伸直链晶体内部球晶形态的观察

自从Wundedich等报道聚乙烯（PE）在高压结晶时可以生成伸直链晶体以来,相继很多有关聚合物体系的高压结晶行为方面的研究已见报道．研究结果表明,聚合物在高压下经历相转变时可产生非常丰富的微观结构,而球晶及伸直链晶体是其中最常见的两种结晶形态．但是,所观察到的这两种聚合物晶体都是分别存在,且独立生长的．到目前为止,尚未见到关于高压下球晶可以在伸直链晶体内部存在的报道．     

原子力显微镜原位观察球晶界面上片晶的生长

当结晶聚合物由熔融冷却或从浓溶液中析出结晶时 ,在不存在应力和流动的情况下 ,一般形成球晶 .球晶在一定的生长时期内呈现球形外观 ,在偏光显微镜下通常呈现Maltese黑十字消光图样 .球晶作为一种常见的结晶形态 ,由片晶堆积而成[1,2 ] .Keith和Padden认为形成球晶的体系包含杂质和聚合物链 ,由于杂质在片晶生长界面的富集导致片晶产生小角度分叉 ,这样片晶能填满球状的空间[1,2 ] .近年来的研究表明球晶是由一个片晶开始生长 ,片晶在生长过程中不断的诱导成核使片晶分叉 ,首先形成片晶捆束 ,然后片晶向各个方向发散生长 ,最终形成球晶[3…     

长链正烷烃的受限结晶研究进展

聚合物的结晶过程和最终凝聚态结构直接影响材料的加工使用性能.作为高分子材料的最大品种,聚烯烃由于分子量大,分子量分布较宽,结晶过程中形成多种亚稳态,因而从分子水平上阐明其结晶机理存在困难.与聚乙烯链结构相似的长链正烷烃可作为聚烯烃的模型化合物,研究其受限结晶行为能为复杂的聚合物受限结晶提供理想的模型体系.长链正烷烃的受限空间可以分为一维受限薄膜、二维受限微孔、三维受限微乳液或微胶囊等.相对于本体,长链正烷烃在每个受限体系中的结晶行为各不相同,这主要来源于受限体系对成核、结晶以及相转变的影响.本文重点综述了长链正烷烃在3种受限体系中的结晶特点,并结合各个体系中聚合物的结晶特点,阐述了长链正烷烃作为聚合物模型化合物的合理性.     

聚乙烯串晶在单轴拉伸形变过程中的微结构变化和机理

本文采用电子显微镜和小角Ｘ－射线散射（ＳＡＸＳ）技术研究了含有串晶结构（Ｓｈｉｓｈ—ｋｅｂａｂ）的高密度聚乙烯（ＨＤＰＥ）／超高分子量聚乙烯（ＵＨＭＷＰＥ）共混物高取向膜在单轴拉伸过程中的微结构变化．深入探讨了拉伸温度对聚乙烯在形变过程中微结构变化的影响．室温拉伸时，聚乙烯串晶结构主要发生了解结晶过程；高温（１１５℃）形变时，主要表现为折叠链片晶直接转变为伸展链纤维晶的应变诱导结晶过程．     

聚ε-己内酯/聚氯乙烯球晶表面的XPS研究

聚合物薄膜在微电子领域中的应用日益增加.聚ε-己内酯/聚氯乙烯（PCL/PVC）是研究得最广泛的聚合物共混薄膜之一.PCL与PVC以一定比例混合时,可以形成环带球晶；同时,体系分为结晶PCL相及PCL/PVC非晶混溶相.用XPS和成象XPS分析技术,对PCL/PVC膜的表面化学组成和元素分布情况进行了研究.观察到PCL在薄膜表面富集.此外,成象XPS表明,PVC在球晶边界处富集,且球晶边界宽度约15 μm.     

Morphosynthesis of hierarchical hydrozincite with tunable surface architectures and hollow zinc oxide

Hydrozincite (Zn5(CO3)2(OH)6) microspheres with a tunable surface architecture have been successfully synthesized via a homogeneous precipitation method under solvothermal conditions. For a smooth hydrozincite microsphere, various building blocks such as nanocubes, nanorods, and nanosheets are arranged to cover a spherical surface by concisely controlling reaction time and the volume of ethylene glycol. Hexagonal Zn5(CO3)2(OH)6 with nanostep structures are also prepared without any additives. The hollow ZnO microspheres with a porous surface have been successfully fabricated via a solution-based method by the room-temperature treatment of filled Zn5(CO3)2(OH)6 microspheres composed of nanocubes. A possible growth mechanism of these hollow ZnO microspheres is proposed. The similar filled ZnO microspheres can also be obtained by a direct pyrolysis of Zn5(CO3)2(OH)6 microspheres composed of nanocubes at 450 degrees C.     

Flexible transparent conducting single-wall carbon nanotube film with network bridging method

Hollow ZrO(2) microspheres with mesoporous shells have been synthesized by a novel hydrothermal reaction of zirconium oxychloride in the presence of urea, hydrochloric acid, and ethanol. The morphology and shell thickness of the hollow microspheres can be controlled by varying synthesis conditions. After calcination at high temperature, the morphologies of the hollow microspheres are essentially preserved. Pt catalyst supported on the hollow calcined ZrO(2) microspheres exhibits more excellent catalytic performance in CO oxidation than those on ZrO(2) powders derived from conventional precipitation methods.     

Preparation of hollow silica microspheres with controlled shell thickness in supercritical fluids

This article presents a novel route to prepare hollow silica microspheres with well-defined wall thickness by using cross-linked polystyrene (PS) microspheres as templates with the assistance of supercritical carbon dioxide (SC-CO₂). In this approach, the cross-linked PS templates can be firstly prepared via emulsifier-free polymerization method by using ethylene glycol dimethacrylate or divinylbenzene as cross-linkers. Then, the silica shell from the sol–gel process of tetraethyl orthosilicate (TEOS) which was penetrated into the PS template with the assistance of SC-CO₂ was obtained. Finally, the hollow silica spheres were generated after calcinations at 600 °C for 4 h. The shell thickness of the hollow silica spheres could be finely tuned not only by adjusting the TEOS/PS ratio, which is the most frequently used method, but also by changing the pressure and aging time of the SC-CO₂ treatment. Fourier transform infrared spectroscopy, transmission electron microscopy, and scanning electron microscope were used to characterize these hollow silica spheres.     

Room temperature fabrication of hollow ZnS and ZnO architectures by a sacrificial template route

Hollow ZnS and ZnO architectures are fabricated by employing Zn(5)(CO(3))(2)(OH)(6) microspheres as the sacrificial template. Zn(5)(CO(3))(2)(OH)(6) microspheres can be effectively converted into the core/shell structured ZnO/ZnS composites (in the Na(2)S solution) and hollow ZnO architectures (in the KOH solution), by a spontaneous ion replacement reaction at room temperature. Removing the core by the KOH treatment of core/shell structured ZnO/ZnS, hollow ZnS spheres with different shell thicknesses can be effectively achieved. The obtained hollow ZnO architectures exhibit unique geometrical shapes, and their walls are composed of nanocrystals, which are connected to each other to form their hemispherical or circular shape. A possible formation process from Zn(5)(CO(3))(2)(OH)(6) microspheres to core/shell structured ZnO/ZnS composites is proposed by arresting a series of intermediate morphologies.     

pH-Responsive hollow polymeric microspheres and concentric hollow silica microspheres from silica-polymer core-shell microspheres

Nearly monodispersed silica-poly(methacrylic acid) (SiO 2-PMAA) core-shell microspheres were synthesized by distillation-precipitation polymerization from 3-(trimethoxysilyl)propylmethacrylate-silica (SiO 2-MPS) particle templates. SiO 2-PMAA-SiO 2 trilayer hybrid microspheres were subsequently prepared by coating of an outer layer of SiO 2 on the SiO 2-PMAA core-shell microspheres in a sol-gel process. pH-Responsive PMAA hollow microspheres with flexible (deformable) shells were obtained after selective removal of the inorganic SiO 2 core from the SiO 2-PMAA core-shell microspheres by HF etching. The pH-responsive properties of the PMAA hollow microspheres were investigated by dynamic laser scattering (DLS). On the other hand, concentric and rigid hollow silica microspheres were prepared by selective removal of the PMAA interlayer from the SiO 2-PMAA-SiO 2 trilayer hybrid microspheres during calcination. The hybrid composite microspheres, pH-sensitive hollow microspheres, and concentric hollow silica microspheres were characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy, X-ray photoelectron spectroscopy (XPS), and energy-dispersive X-ray (EDX) analysis.     

聚合物模板微球表面电性对中空二氧化硅微球形貌的影响

分别以过硫酸钾和偶氮二异丁基脒盐酸盐为引发剂,以聚乙烯吡咯烷酮(PVP)为分散剂,在水中引发苯乙烯聚合制备了2种表面分别带负电性和正电性基团的聚苯乙烯(PS)模板微球.在氨水催化下,利用正硅酸乙酯的水解缩合,形成PS/SiO_2复合微球,去除模板后得到中空SiO_2微球,并对其进行FTIR、电子显微镜、TGA以及氮气吸附等分析表征.结果表明,PS模板微球表面的电性决定了OH-的分布,从而导致PS模板微球表面SiO_2壳层不同的形成机制.当以表面带负电的PS微球为模板时,可得到树莓状的中空SiO_2微球;而以表面带正电的PS微球为模板时,得到是表面光滑的,具有介孔结构的中空SiO_2微球.     

Anomalous effects of helium head pressure carbon dioxide in supercritical fluid chromatography and extraction

Helium head pressure carbon dioxide cylinders are commonly used to facilitate the delivery of liquid CO2 to supercritical fluid extraction and chromatographic pumps. It is usually tacitly assumed that the helium used to increase the delivery pressure of the CO2 cylinders is completely insoluble in liquid CO2 and thus remains isolated in the head space of the delivery cylinder. This assumption is invalid because up to 5 mol% helium can be entrained in the liquid CO2 delivered from helium head pressure cylinders. Significantly, contamination of liquid CO2 with even small amounts of helium can cause many unforeseen and usually deleterious effects in supercritical fluid chromatography and extraction schemes. The observed anomalies include decreased density of the fluid phase, irreproducible extraction and retention, ghost peaks, and even phase separation within the column or extraction vessel.     

An anion exchange approach to Bi(2)WO(6) hollow microspheres with efficient visible light photocatalytic reduction of CO(2) to methanol

An anion exchange strategy is explored to synthesize Bi(2)WO(6) hollow microspheres based on the microscale Kirkendall effect. The as-prepared Bi(2)WO(6) hollow microspheres display high CO(2) adsorption capacity and visible light photocatalytic conversion efficiency of CO(2) into methanol without the aid of any co-catalyst.     

超临界流体萃取在天然药物分析中的应用

按物质的不同性质综述了１９９５年以来超临界流体萃取技术在天然药物分析中的一些进展情况,常见的分析主要包括萜类、生物碱、黄酮类、挥发油及苯丙素类。超临界流体萃取作为一门新型的样品前处理技术,在天然药物的分离分析中展示了其特有的优点。该技术操作温度低,不会引起热敏性的分解变质;使用的有毒溶剂少,从而减少化学药品对药物的污染。     

超临界流体萃取-硅胶柱收集联用提取蓬莪术中有效成分

采用超临界流体CO2萃取和硅胶柱收集在线联用,提取蓬莪术中的挥发油,随后分别用正己烷、乙醇和乙醚对硅胶柱进行选择性洗脱,从而使蓬莪术挥发油中有效成分莪术二酮的相对含量由原来单一萃取的10．7％提高到34．7％。