Melamine integrated metal phosphates as non-halogenated flame retardants: Synergism with aluminium phosphinate for flame retardancy in glass fiber reinforced polyamide 66

An integrated multicomponent molecule, Melamine-poly(aluminium phosphate) (Safire^®200), its zinc and magnesium analogues namely Safire^®400 and Safire^®600 respectively were used as flame retardants for glass fiber reinforced polyamide 66 in combination with aluminium phosphinate. Characterisation, thermal stability, combustion properties, glow-wire flammability index and glow-wire ignition temperature and cone calorimetry results are reported. Lower threshold of loading of flame retardants that pass V0 rating in UL-94 vertical burning test have been determined. Effect of Zinc borate (Firebrake^®500 grade) in these formulations was investigated. Influence of additives on endothermic and exothermic transitions of polyamide 66 in these formulations were studied by differential scanning calorimetry. The formulations were evaluated against the properties and fire performances of classical commercial combination of aluminium phosphinate and melamine polyphosphate. All the new formulations down to 15% of additives loading achieve V0 rating according to UL-94 protocol. This synergistic combination of additives significantly reduces the peak of heat release rate (pHRR) and total heat release (THR) in formulations exhibiting various degrees of intumescence.     

Preparation of flame retardant polyamide 6 composite with melamine cyanurate nanoparticles in situ formed in extrusion process

This paper is focused on in situ preparation of melamine cyanurate (MCA) nanoparticles from reaction of melamine (MEL) and cyanuric acid (CA) and their flame retardant polyamide 6 (PA6) composite in the extrusion process through a novel reactive processing method. Fourier transform infrared (FT-IR), X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) were utilized to characterize the in situ formed MCA nanoparticles and their blends with PA6. Introduction of pentaerythritol (LTP) and water-bound plasticizer dioctyl phthalate (DPT) into the extrusion reaction system greatly inhibits the evaporation of water required for melamine and cyanuric acid reaction at high temperature (higher than 180 °C), laying a foundation for successful in situ preparation of MCA through reactive processing. XRD and FT-IR measurements indicate that under the effect of pentaerythritol, dioctyl phthalate and water, melamine really reacts with cyanuric acid to in situ form MCA in extrusion process. The reaction degree is close to 100%. A very important finding through SEM is that the in situ formed MCA particles, which were found to have aspect ratio of about 7.5, radial size in the range of 70-300 nm (mostly 70-90 nm) and crystallite size of less than 22 nm, are uniformly dispersed in the matrix PA6 at nanoscale. The in situ formed MCA nanoparticles greatly improve the flame retardancy and the mechanical properties of flame-retarded PA6 materials, and the introduced plasticizer dioctyl phthalate also ameliorates the related impact property. The obtained flame-retarded PA6 materials have good comprehensive performance with flame retardancy UL-94 V-0 rating at 1.6 and 3.2 mm thickness, tensile strength 48.0 MPa, elongation at break 106.3% and Izod notched impact strength 8.92 kJ/m². Compared with flame-retarded PA6 material with in situ formed MCA, the one prepared through conventional blending of PA6 with commercial MCA product has improved tensile strength but deteriorated impact strength and flame retardancy.     

Melamine cyanurate-microencapsulated red phosphorus flame retardant unreinforced and glass fiber reinforced polyamide 66

A novel microencapsulated red phosphorus (RP) was prepared through the molecular self-assembly of melamine cyanurate (MCA). Compared with the conventional encapsulated RP, MCA-encapsulated RP (MERP) shows simpler and more environment-friendly preparation process higher thermal stability and lower moisture absorption. With MERP filled in unreinforced polyamide 66 (PA66) and glass fiber (GF) reinforced PA66, flame retardant materials with satisfactory flame retardancy and mechanical performance can be obtained. The influence of the MCA/RP ratio on the flame retardancy as well as the condensed phase of MERP flame retardant PA66 was investigated to reveal the nitrogen-phosphorus (N-P) synergistic flame retarding effects between MCA and RP.     

Flame retardancy mechanisms of aluminium phosphinate in combination with melamine polyphosphate and zinc borate in glass-fibre reinforced polyamide 6,6

The fire retardancy mechanisms of aluminium diethylphosphinate in combination with melamine polyphosphate and zinc borate was analysed in glass-fibre reinforced polyamide 6,6. The influence of phosphorus compounds on the polyamide decomposition pathways was characterized using thermal analysis (TG), evolved gas analysis (TG-FTIR), and FTIR-ATR analysis of the residue. The Lewis acid-base interactions between the flame retardants, the amide unit, and the metal ions control the decomposition. The flammability (LOI, UL 94) and performance under forced-flaming conditions (cone calorimeter using different irradiations) were investigated. Fire residues were analysed with FTIR-ATR, SEM-EDX, and NMR. Aluminium phosphinate in polyamide 6,6 acts mainly by flame inhibition. Melamine polyphosphate shows some fuel dilution and a significant barrier effect. Using a combination of aluminium phosphinate and melamine polyphosphate results in some charring and a dominant barrier effect. These effects are improved in the presence of zinc borate due to the formation of boron-aluminium phosphates instead of aluminium phosphates.     

Nanoclay synergy in flame retarded/glass fibre reinforced polyamide 6

Exfoliated clay nanocomposites of flame retarded/glass fibre reinforced polyamide 6 were prepared by twin-screw extrusion compounding. A flame retardant system based on phosphorus compounds and zinc borate was used at various levels in glass fibre reinforced PA6 and nanocomposites. Thermal stability and combustion behaviours were evaluated by TGA, LOI, UL94 and cone calorimetry. Substitution of a certain fraction of the flame retardant with nanoclays was found to significantly reduce the peak heat release rate and delay ignition in the cone calorimeter. Moreover, remarkable improvements were obtained in LOI along with maintained UL94 ratings. Residue characterization by FTIR, XRD and SEM ascribed the enhanced flame retardancy of nanocomposite formulations to the formation of a glassy boron/aluminium phosphate barrier reinforced by clay layers at the nanoscale. The physically strong and consolidated barriers formed from nanocomposites were much more effective in impeding heat and mass transfer compared to those from conventional formulations.     

Flame retardation of glass-fibre-reinforced polyamide 6 by a novel metal salt of alkylphosphinic acid

Aluminum salts of phosphinic acid mixture of diisobutylphosphinic acid and monoisobutylphosphinic acid (HPA-2TBA-Al) and glass fibres were compounded with polyamide 6 to prepare a series of flame retardant GF/PA6 composites via melt blending. The flame retardance and burning behaviors of the composites were investigated by limiting oxygen index (LOI), vertical burning test (UL-94), and Cone calorimeter test. The thermal properties and decomposition kinetics were investigated by thermogravimetric analysis (TGA) under N₂ atmosphere. Addition of HPA-2TBA-Al results in an increased LOI value, a UL-94 V-0 rating together with a decrease in both the values of PHRR and THR in Cone calorimetric analysis. Visual observations and scanning electronic microscopy (SEM) after flame retardant tests confirmed the char-formation which acts as a fire barrier in condense phase. Analysis of cone calorimeter data indicates that gas phase flame retardant mechanism exists in the GFPA6/HPA-2TBA-Al system.     

Influence of maleic anhydride-grafted EPDM and flame retardant on interfacial interaction of glass fiber reinforced PA-66

In this paper, the effects of melamine polyphosphate flame retardant (MPP-FR) and maleic anhydride-grafted EPDM (MA-EPDM) on the interfacial interaction of PA66/GF were investigated by means of scanning electron microscopy (SEM), dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), rheological behavior and mechanical properties. The experimental results demonstrate that MPP-FR and MA-EPDM could effectively improve interfacial interactions between the PA66 and GF. Based on SEM, good interfacial adhesion between PA66 and GF in PA66/GF/FR and PA66/GF/FR/MA-EPDM composites was observed, however, MPP-FR destroyed the PA66 matrix. DMA results show that MPP-FR increased glass transition temperature (T_g) and storage modulus, and lower tan δ, while MA-EPDM showed a little effect on them in PA66/GF/FR/MA-EPDM composite compared with PA66/GF/FR. MPP-FR made PA66 crystallization temperature and the activation energy of the macromolecular segments transport increase clearly, and enhanced crystallization degree of PA66 according to DSC results. These results demonstrate MPP-FR presented the nucleate effect for the crystallization of PA66. At the low shear rate, MPP-FR and MA-EPDM obviously enhanced apparent viscosities of the composites. This is attributed that MPP-FR improved the interfacial interaction of the composites, and MA-EPDM promoted the formation of high molecular weight structures by the reactions between MA and amine groups. All results in this paper were consistent, and showed the good interaction among PA66, GF, MPP and MA-EPDM, which were proved by the mechanical properties of the composites.     

Effects of carbon nanotubes on the thermal stability and flame retardancy of intumescent flame-retarded polypropylene

Flame retardant mixtures of carbon nanotubes (CNTs) and intumescent flame retardant (IFR) were embedded in polypropylene (PP) to investigate what will happen if the additives exhibit two different flame retardation mechanisms. TEM tests showed that CNTs dispersed homogenously in PP matrix without any visible agglomeration. The effects of CNTs on thermal stability and flammability of PP were investigated by thermogravimetry (TG) and cone calorimetry tests, respectively. Results indicated that the introduction of CNTs only enhanced thermal stability of materials in a certain temperature range, but caused a severe deterioration of flame retardancy due to the interaction of the network structure and the intumescent carbonaceous char. Furthermore, conditions for an intumescent flame retardation system to behave with high efficiency were also discussed by a secondary combustion test.     

Effect of electrospun polyamide 6 nanofibres on the mechanical properties of a glass fibre/epoxy composite

Recently, several types of nanoparticles are frequently incorporated in reinforced epoxy resin composites. A homogeneous dispersion of these nanoparticles is still a problem. Thermoplastic nanofibrous structures can tackle this dispersion issue. Therefore, this paper investigated the effect of electrospun polyamide 6 nanofibrous structures on the mechanical properties of a glass fibre/epoxy composite. The nanofibres were incorporated in the glass fibre/epoxy composite as stand-alone interlayered structures and directly spun on the glass fibre reinforcement. Both ways of nanofibre incorporation have no negative effect on the impregnation of the epoxy. Moreover, the nanofibres remain well dispersed within the matrix. Incorporation of nanofibres increases the stress at failure in the 0°-direction, the best results are obtained when the nanofibres are directly electrospun onto the glass fibres. Optical microscopic images also demonstrate that nanofibres prevent delamination when a 90° crack reaches a neighbouring 0° ply. Furthermore, mode I tests showed a small improvement when a thin nanofibrous structure is deposited directly onto the glass fibres. When the composites are loaded under 45°, it is proven that, for an identical stress, the glass fibre composite with deposited nanofibres has less cracks than when interlayered nanofibrous structures are incorporated. Generally, it can be concluded that the addition of polyamide 6 nanofibres improves some mechanical characteristics of a glass fibre/epoxy composite.     

Mechanical properties and morphological structures of short glass fiber reinforced PP/EPDM composite

The mechanical properties and crystal morphological structures of short glass fiber (SGF) reinforced dynamically photo-irradiated polypropylene (PP)/ethylene-propylene-diene terpolymer (EPDM) composites were studied by mechanical tests, wide-angle X-ray diffraction (WAXD), optical microscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and thermogravimetric analyzer (TGA). The mechanical properties of PP/EPDM composites, especially the tensile strength were greatly strengthened by dynamically photo-irradiation and the incorporation of SGF. The results from the WAXD, SEM, DSC, and TGA measurements reveal: (i) the formation of β-type crystal of PP in the PP/EPDM/SGF composite; (ii) the fiber length in dynamically photo-irradiated PP/EPDM/SGF composites are general longer than that in corresponding unirradiated samples. The size of EPDM phase in the photo-irradiated composites reduces obviously whereas the droplet number increases; (iii) photo-irradiation improves the interface adhesion between SGF and polymer matrix; (iv) the melting and crystallization temperatures of the photo-irradiated composites are not affected greatly by increasing the SGF content; (v) the thermal analysis results show that the incorporation of SGF into PP/EPDM plays an important role for increasing its thermal stability.     

Ammonium sulfamate flame retarded polyamide 6: Morphology and thermal degradation

<正>The effect of ammonium sulfamate(AS) content on the flame retardancy of polyamide 6(PA6) was studied.It is found that the limiting oxygen index(LOI) of PA6 increases with the increase of AS content and the flame retardancy of PA6 is significantly improved.The morphology of the residues after combustion was examined by means of scanning electron microscopy(SEM).SEM results show that AS facilitates the formation of the intumescent char layer with honeycomb-like structure,which inhibits the transfer of heat and mass,and thus improves the flame retardancy of PA6.The thermal degradation of AS flame retarded PA6 was studied by thermogravimetric analysis(TGA).The Kissinger method was applied to estimate the activation energy(E_a) of the degradation.The activation energy of the thermal degradation of PA6 decreases by adding AS,indicating that AS can promote the degradation of PA6.     

Synergistic effect of SEBS-g-MA and epoxy on toughening of polyamide 6/glass fiber composites

Maleated styrene-ethylene-butylene-styrene block copolymer (SEBS-g-MA) and epoxy monomer, individually or in combination, are used to toughen polyamide 6/glass fiber composites. The epoxy monomer enhanced interaction between polyamide 6 and glass fiber. SEBS-g-MA rubber is uniformly dispersed in polyamide 6 matrix caused by the preferred compatibilizing reaction between the anhydride group of rubber and the amine terminal group of polyamide 6. The addition of epoxy does not affect the fine dispersion of SEBS-g-MA. Polyamide 6/glass fiber binary composites are brittle. The addition of epoxy monomer alone does not change their brittle features. Similarly, in the absence of epoxy monomer, adding 20 wt % of SEBS-g-MA to polyamide 6/glass fiber composites does not greatly increase the tensile ductility. Only when both SEBS-g-MA and epoxy monomer are present in some combination, do the polyamide 6/glass fiber composites show prominent ductile characteristics, such as stress-whitening and necking. This synergistic effect of epoxy monomer and SEBS-g-MA also imparts higher notched impact strengths to the ternary composites. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1448–1458, 2007     

Effects of reprocessing on the structure and properties of polyamide 6 nanocomposites

PA6 based nanocomposites (NCs) were reprocessed by repeated injection moulding to find out whether reprocessing is possible in these materials by means of the observation of the changes in the structure and mechanical properties. The studied variables were (a) the number of cycles (1-5), (b) the origin of the NC: either laboratory mixed or commercial and (c) the processing temperature (230 °C and 270 °C). Neat PA6 was also reprocessed as a reference material. In spite of the colour change, the Young's modulus, the solid state characteristics and the dispersion level were preserved upon reprocessing. The lack of change of chemical nature observed by FTIR, and the observed decreases in viscosity indicated that the main effect of reprocessing was a decrease in the molecular weight. At 230 °C the decreases in viscosity were smaller after reprocessing, and almost no change was seen in the structural parameters and properties. The decrease in the molecular weight after reprocessing at 270 °C leads to lower ductility and mainly to a decrease in the ability of the nPA6 matrix to cold draw. However, no change of the interphase conditions or agglomeration of the OMMT was detected and the NCs remained clearly ductile; thus, revealing a lack of deterioration of the interface and the ability of the NCs for recycling.     

Effect of maleic anhydride-grafted ethylene-propylene rubber on the mechanical, rheological and morphological properties of organoclay reinforced polyamide 6/polypropylene nanocomposites

Polyamide 6/polypropylene (PA6/PP = 70/30 parts) blends containing 4 phr (parts per hundred resin) of organophilic modified montmorillonite (organoclay) were compatibilized with maleic anhydride-grafted ethylene-propylene rubber (EPRgMA). The blends were melt compounded in twin screw extruder followed by injection molding. The mechanical properties of PA6/PP nanocomposites were studied by tensile and flexural tests. The microstructure of the nanocomposite were assessed by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The dynamic mechanical properties of the PA6/PP blend-based nanocomposites were analyzed by using a dynamic mechanical thermal analyzer (DMTA). The rheological properties were conducted from plate/plate rheometry via dynamic frequency sweep scans. The melt viscosity in a high shear rate region was performed by using a capillary rheometer. The strength and stiffness of the PA6/PP-based nanocomposites were improved significantly with the incorporation of EPRgMA. Adding EPRgMA to the PA6/PP blends resulted in a finer dispersion of the PP phase. TEM and XRD results revealed that the organoclay was dispersed more homogeneously in the presence of EPRgMA, however, mostly in the PA6 phase of the blends. DMTA results showed that EPRgMA worked as an effective compatibilizer. The storage (G′) and loss moduli (G″) assessed by plate/plate rheometry of PA6/PP blends increased with the incorporation of EPRgMA and organoclay. Furthermore, the apparent shear viscosity of the PA6/PP blend increased significantly for the EPRgMA compatibilized PA6/PP/organoclay nanocomposite. This was traced to the formation of an interphase between PA6 and PP (via PA6-g-EPR) and effective intercalation/exfoliation of the organoclay.     

Fire response of polyamide 6 with layered and fibrillar nanofillers

To improve the fire retardancy performance of polyamide 6 (PA 6), layered silicates are used in combination with multi-walled carbon nanotubes (CNTs) to address the issue of packing density and uniformity of the protective inorganic barrier formed at the burning surface of the nanocomposites during combustion. Benzimidazolium is used to modify the silicate layers instead of conventional alkyl ammonium surfactants to tackle the issue of thermal stability. However, the poor dispersion of the modified layered silicates in PA 6 has a significant negative effect on the fire performance of the materials and offsets the positive effect of CNTs. Also, the results point to the apparent contradictions with different fire exposure tests; that is, significant reductions in heat release and mass loss rates in the cone calorimetry test do not imply a higher rating in the UL 94 vertical burning test.     

Preparation of ZnO nanoparticle‐reinforced polyamide 6 composite by in situ‐coproduced method and their properties

Polyamide 6/ZnO nanocomposites (noted as PA6/ZnO) were prepared by an in situ co‐producing method, during which Zn₂(OH)₂CO₃ decomposed into nano‐ZnO in the process of the opening‐ring polymerization of caprolactam at high temperature. Transmission electron microscopy, X‐ray diffraction, thermogravimetric analysis, and differential scanning calorimetry were used to analyze the size and dispersive properties of nano‐ZnO, the crystallization and melting properties, the thermal properties, and crystal structure of PA6/ZnO composite, respectively. The results showed that the nano‐ZnO derived from Zn₂(OH)₂CO₃ via in situ polymerization of PA6‐ZnO was uniformly dispersed in PA6 matrix. However, the overall nano‐ZnO crystallization rate and crystal size in the PA6 matrix were hindered by the bulky PA6 molecular chains. The mechanical properties were evaluated using universal tensile and impact testing instruments. The results revealed that PA6/ZnO composite with 0.2% nano‐ZnO content possessed excellent tensile strength, enhanced by 75% in comparison with the pure PA6. The nano‐ZnO had little influence on the impact strength of PA6. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 165–170     

Morphology and properties of ternary polyamide 6/polyamide 66/elastomer blends

The aim of the work presented is to evaluate the mechanisms and phase interactions in ternary blends based on different polyamides and functionalised elastomers, and to establish a correlation between the morphology controlled by the specific binary interactions, and physical and technological properties, respectively. The properties of the ternary system polyamide 6/polyamide 66/ elastomer depend on the specific blend morphology which is determined mainly by the differences of the surface tension of the components. A phase‐in‐phase structure was observed by microscopic study (AFM) in the ternary polyamide 6/polyamide 66/elastomer blends with maleic anhydride grafted ethene‐octene copolymer, and a “quasi” phase‐in‐phase structure in blends with maleic anhydride grafted ethene‐propene‐diene copolymer as the elastomer phase. An incorporation of polyamide inside of the elastomer particles was observed in the first case due to the difunctionality of polyamide 66. This type of morphology causes an increased elongation at break and toughness of these blends. In comparison to the binary polyamide based blends the ternary blends show an increased elastic modulus, elongation at break and yield stress as well as a high impact strength at low temperatures up to ?20 °C. Copyright © 2003 John Wiley & Sons, Ltd.     

聚磷酸铵-苯并噁嗪微胶囊的制备及其对环氧树脂燃烧性能影响

以多聚甲醛、丙烯胺、苯酚为原料,通过Mannich反应合成烯丙基型苯并噁嗪单体(Bala),并通过核磁共振氢谱(~1H-NMR)确定了其化学结构.将Bala在聚磷酸铵(APP)原位开环聚合后,制备APP微胶囊(BMAPP).傅里叶变换红外(FTIR)和静态接触角测试表明,Bala在APP表面成功聚合,并有效提高APP的疏水性,与纯APP相比,BMAPP的接触角从10.8°提高到了71.3°.将BMAPP添加到环氧树脂(EP)中,制备EP/BMAPP复合材料.通过热重分析仪(TGA)、垂直燃烧(UL-94)、极限氧指数(LOI)、锥型量热仪(CONE)和动态热机械分析仪(DMA)对EP和EP/BMAPP的热性能以及燃烧性能进行对比分析.结果显示,10%的BMAPP的成炭效果最佳,有良好的阻燃性能,可使EP的LOI值从22.6%提高到33.6%,并通过UL-94 V-0级,600°C下残炭率达26.3%.同时,BMAPP可大幅度降低EP燃烧过程中烟密度和热释放速率,提高EP的玻璃化转变温度(T_g).BMAPP/EP-10%中,PBala和APP协同后使EP热释放速率峰值(PHRR)由1247 kW·m~(-2)降低到434 kW·m~(-2),生烟速率(SPR)降低67%左右,T_g从169°C提高到了173°C.     

Chain rupture and tensile deformation of polyamide 6 fibers

Summary The tensile deformation of polyamide 6 fibers gives rise to irreversible changes of its tensile properties, which apparently arise from chain rupture. This molecular failure process is usually analyzed by means of the ESR-spectroscopy. The number of ruptured chains, as obtained by this method, is, however, much too small to account for the changes of the tensile properties and for the observed strong decrease of the average molecular weight. Based on studies on energy dissipation, on structural as well on spectroscopical investigations we come to the conclusion that chain rupture is mainly responsible for the irreversible changes of the tensile properties. The dissipation of energy can be accounted for in terms of the energy release on chain rupture and energetic interactions with neighboring segments, in agreement with the data on the molecular weight decrease. The spectroscopically determined number of ruptured chains is governed by a fast recombination of the free radicals.

---

Zusammenfassung Eine Deformation von Polyamid 6 Fasern führt zu irreversiblen Veränderungen in den mechanischen Eigenschaften, die offensichtlich durch Kettenbrüche verursacht werden. Dieser molekulare Versagensprozeß wird gewöhnlich mittels der ESR-Spektroskopie analysiert. Die hierdurch erhaltene Anzahl an Kettenbrüchen ist jedoch viel zu gering, um sowohl die Veränderungen in den mechanischen Eigenschaften als auch die starke Abnahme des mittleren Molekulargewichtes erklären zu können. Auf der Grundlage unserer Untersuchungen zur Energiedissipation, aus Streuexperimenten und spektroskopischen Untersuchungen kommen wir zu dem Schluß, daß Kettenbrüche für die Veränderungen der Eigenschaften allein verantwortlich sind. Die Energiedissipation läßt sich vollständig auf die Energiefreisetzung beim Kettenbruch und energetische Wechselwirkungen mit umgebenden Segmenten zurückführen, in Einklang mit den Ergebnissen zur Molekulargewichtserniedrigung. Die spektroskopisch bestimmte Anzahl an Kettenbrüchen wird durch eine schnelle Rekombination der freien Radikale beeinträchtigt.