Investigating the effect of accelerated weathering on the mechanical and physical properties of high content plastic solid waste (PSW) blends with virgin linear low density polyethylene (LLDPE)

In developing countries, plastic solid waste (PSW) poses a serious threat due to the increase in the dependency on landfilling as well as other environmental issues. Hence, valorising the accumulated waste is essential to promoting more environmentally friendly practices. In this work, the mechanical and physical properties of virgin linear low density (LLDPE) and LLDPE blends with PSW are reported. The formulations studied contained the following virgin to waste ratios (wt.%/wt.%): 100/0, 75/25, 50/50, 25/75 and 10/90. The effect of photo-degradation on the studied specimens was investigated using accelerated weathering tests in a UV chamber. Young's modulus showed an increase with exposure duration due to change in the samples' crystallinity. The loss of mechanical integrity (i.e. stress and strain at rupture) of the samples studied was related to the photo-degradation mechanisms, namely cross-linking and photo-oxidation. Haze and light transmission measured indicated that there was a loss of the amorphous regions in the samples studied after about 200 h of continuous exposure. The total change in colour (ΔE) was estimated but did not show a clear trend, indicating a clear dependency on wash mechanism and continuous loss of polymer colour and degradation.     

The effect of different variables on the accelerated and natural weathering of agricultural films

Lifetimes required for greenhouse cover films depend heavily on the country, especially the tradition in the country. They vary from one agricultural season (i.e. 6-9 months) to several years and are strongly dependent on the use of pesticides which destroy the photostabilisers (HALS and nickel quenchers) and on other geographic and climatic factors (solar irradiation, temperature, winds, etc.).In this work, we have measured the duration of four real agricultural films using the European Standard EN 13206:2001 conditions for the accelerated weathering test and the results have been compared to their duration under accelerated weathering using more aggressive conditions (pesticide spraying, different chamber temperatures) and under natural weathering. We have also explored the effect of the backing material in the artificial weathering test and of the starting date in the natural weathering. The final goal of this study is to obtain good correlations between accelerated weathering, natural weathering at defined, controlled conditions and weathering in real-use conditions for agricultural films.     

Effect of experimental conditions on nano-indentation response of low density polyethylene (LDPE)

Nano-indentation is an interesting tool for analyzing nano-scale mechanical properties. The analysis of nano-mechanical properties as a function of experimental conditions is very critical for designing engineering components. In this study, nano-indentation experiments were performed by considering different values of amplitude (1, 5, 10?nm), frequency (11.2, 22.5, 45?Hz), strain rate (0.02, 0.05, 0.1, 0.2, 1?s^?1), peak load (10, 30, 100?mN) and hold time (1, 3, 5, 10, 20, 50, 100?sec) to analyze their effect on the mechanical properties of LDPE. The results showed that the effect of amplitude and frequency on the nano-mechanical properties of LDPE were negligible. Load-displacement curves displayed a shift towards higher indentation depths along with a decrease in peak load from 20.6 to 14.8?mN by having a decrease in strain rate from 1 to 0.02?s^?1. Elastic modulus and hardness values exhibited a decrease with an increase in hold time. Logarithmic creep model was used to fit the experimental data of creep as a function of holding time which showed good agreement (r² ≥ 0.97) with the experimental values. Recommended holding times are also suggested to eliminate the creep and nose problem in order to achieve high accuracy in measurements.     

Effects of coating composition and surface pre-treatment on the adhesion of organic-inorganic hybrid coatings to low density polyethylene (LDPE) films

Organic-inorganic hybrid coatings, obtained through the sol-gel chemistry from tetraethoxysilane and polyethylene-poly(ethylene glycol) block copolymer, have been prepared in different compositions and applied to untreated and plasma treated LDPE films by spin coating. The mechanical properties of the coatings and the adhesion between coating and substrate have been characterized by fragmentation test. An increase in coating strength, elongation at break and adhesion has been observed with increasing the organic fraction in the hybrid coating. A plasma treatment of the LDPE surface, just before the application of the coating, lead to an increase of the adhesion between coating and substrate (interfacial shear strength), leaving almost unaffected coating strength and strain at fragmentation onset.     

Morphology and mechanical properties of blown films of a low‐density polyethylene/linear low‐density polyethylene blend

The morphologies of films blown from a low‐density polyethylene (LDPE), a linear low‐density polyethylene (LLDPE), and their blend have been characterized and compared using transmission electron microscopy, small‐angle X‐ray scattering, infrared dichroism, and thermal shrinkage techniques. The blending has a significant effect on film morphology. Under similar processing conditions, the LLDPE film has a relatively random crystal orientation. The film made from the LDPE/LLDPE blend possesses the highest degree of crystal orientation. However, the LDPE film has the greatest amorphous phase orientation. A mechanism is proposed to account for this unusual phenomenon. Cocrystallization between LDPE and LLDPE occurs in the blowing process of the LDPE and LLDPE blend. The structure–property relationship is also discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 507–518, 2002; DOI 10.1002/polb.10115     

Studies on dynamic mechanical and mechanical properties of vinyloxyaminosilane grafted ethylene propylene diene terpolymer/linear low density polyethylene (EPDM-g-VOS/LLDPE) blends

The dynamic mechanical properties of vinyloxyaminosilane grafted ethylene propylene diene terpolymer/linear low density polyethylene (EPDM-g-VOS/LLDPE) blends have been evaluated with special reference to the effect of blend ratio. It has been found that increasing the proportion of LLDPE in the blends decreases the T_g values and increases the storage modulus (E^′) and loss modulus (E^′′) due to increase in crystallinity. A gradual increase in the values of tanδ_max is observed for the blends with increase in EPDM-g-VOS concentration, which indicates that no phase inversion occurs. But however the higher increase in tanδ_max after 50 wt.% of EPDM-g-VOS composition is due to small change in crystallinity and is ascertained by SEM micrographs. Mechanical properties such as tensile strength, Young’s modulus and hardness increase with increases in LLDPE concentration in the blends and with dicumyl peroxide (DCP) concentration whereas the values of elongation at break are decreased with increase in LLDPE and DCP concentration.     

Effects of ultrasonic oscillations on linear viscoelastic behaviors of metallocene‐catalyzed linear low density polyethylene and its blends with low density polyethylene

The effects of ultrasonic oscillations on linear viscoelastic behaviors of metallocene‐catalyzed linear low density polyethylene (mLLDPE) and its blends with low density polyethylene (LDPE) were investigated in this article. The experimental results showed that ultrasonic oscillations can increase the cross modulus, characteristic time, plateau modulus, complex viscosity, zero shear viscosity, and flow activation energy of mLLDPE. Molecular weight of mLLDPE increases but molecular polydispersity index decreases in the presence of ultrasonic oscillations. It has been found for mLLDPE/LDPE blends that the addition of LDPE as well as ultrasonic oscillations can decrease the cross modulus but increase the characteristic time of the blends. The complex viscosity, zero shear viscosity, and flow activation energy of the blends increase by the addition of LDPE, but decrease in the presence of ultrasonic oscillations. Shear thinning effect of the blends is improved because of the addition of LDPE. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3030–3043, 2005     

Preparation and characterization of vinyltriethoxysilane grafted ethylene propylene diene terpolymer/linear low density polyethylene (EPDM‐g‐VTES/LLDPE) blends

Graft polymerization of vinyltriethoxysilane (VTES) onto ethylene‐propylene‐diene terpolymer (EPDM) was carried out in toluene using dicumylperoxide (DCP) as initiator. Effects of various parameters (EPDM content, VTES content, reaction time, reaction temperature and initiator concentration) on the grafting efficiency of VTES onto EPDM were investigated. At the optimum grafting efficiency conditions, EPDM‐g‐VTES was developed by melt mixing in a twin screw extruder and then linear (l), statically vulcanized (s) and dynamically vulcanized (d) blends of EPDM‐g‐VTES with linear low‐density polyethylene (LLDPE) with varying percentage compositions were prepared by melt mixing in the twin screw extruder. The grafting of VTES onto EPDM and its crosslinking was confirmed by FT‐IR. The characterization of mechanical properties such as tensile strength, elongation at break, Young's modulus and hardness, differential scanning calorimetry (DSC) analysis and morphology were studied and compared for the EPDM‐g‐VTES/LLDPE blends. The study reveals that the dynamically vulcanized blend improves the mechanical and thermal properties due to the presence of efficient interaction between component polymers when compared with other blends. Copyright © 2005 John Wiley & Sons, Ltd.     

Nonisothermal crystallisation, melting behavior and wide angle X-ray scattering investigations on linear low density polyethylene (LLDPE)/ethylene vinyl acetate (EVA) blends: effects of compatibilisation and dynamic crosslinking

Crystallisation studies on LLDPE/EVA blends and the individual components were performed with wide angle X-ray scattering (WAXS) technique and differential scanning calorimetry (DSC) DSC was used to characterise the quiescent crystallisation behavior. The heat of fusion and crystallinity of the blends were reduced by the addition of EVA. The experimental and theoretical values of crystallinity of the blends were found to be mutually agreeing. Crystallisation of LLDPE remains impeded to some extent due to the presence of amorphous EVA. Compatibilisation does not affect crystallinity whereas crosslinking decreases crystallinity. Crosslinking and compatibilisation make no significant change in the melting temperature of the blends. X-ray diffraction studies were carried out on un-crosslinked and crosslinked LLDPE/EVA blends with a view to study the effect of blend composition and crosslinking on crystallinity and lattice distance. Studies revealed that LLDPE and EVA have orthorhombic unit cell. Blending with EVA did not affect the crystalline structure of LLDPE, but the crystallinity decreases with EVA content. At low concentrations of EVA the lattice parameters remain unchanged. Above 30% EVA content however, a linear increase has been observed. Dicumyl peroxide (DCP) crosslinked samples show considerable shift of (1 1 0), (2 0 0) and (0 2 0) crystalline peaks towards lower 2θ values indicating an increase of unit cell parameters of the orthorhombic unit cell of polyethylene. At lower EVA-concentrations (<50%) the crystalline structure remains unchanged. For EVA-contents of more than 70% however, increasing DCP-content reduces the crystallinity of the blends and increases the lattice distance. This indicates that DCP-crosslinking is more effective in EVA phase than in the LLDPE phase.     

Influence of the repeated extrusion on the degradation of polyethylene. Structural changes in low density polyethylene

The influence of the repeated extrusion on the molecular parameters of low density polyethylene (LDPE) Bralen NA 7-25 was studied. Virgin polyethylene was submitted up to 20 extrusion cycles and the processed samples were fractioned using precipitation fractionation. Non-fractionated samples and the individual polymer fractions were characterized by their weight average molar masses M_w (static light scattering), number average molar masses M_n (osmometry) and limiting viscosity numbers [η] (viscometry). Rheological properties in terms of shear viscosity curve, zero shear viscosity and flow activation energy were also determined by using high pressure capillary rheometer. The course of the changes in molecular parameters of LDPE is influenced both by the initial polymer structure and by the changes induced by the mechano-chemical degradation. The suggested degradation mechanisms during multiple extrusion of Bralen are chain scission predominating in the early stage of processing followed by recombination of macromolecules resulting in crosslinking and formation of microgel, which is clearly notable for the samples extruded 3-20 times.     

Rheological investigation of the influence of molecular structure on natural and accelerated UV degradation of linear low density polyethylene

Metallocene and Ziegler-Natta (ZN) linear low density polyethylenes (LLDPEs) of different branch types and contents as well as linear high density polyethylene (HDPE) were exposed to natural and accelerated weather conditions. The degree of UV degradation of exposed samples was measured by rheological techniques and results were compared with unexposed polymers. Dynamic shear measurements were performed in an ARES rheometer in the linear viscoelastic range. The degree of enhancement or reduction in viscosity and elasticity was used as a measure of the degree of cross-linking or chain scission, respectively. The degradation results of LLDPE suggest that both cross-linking and chain scission are taking place. Chain scission dominated the degradation at high levels of short chain branching (SCB) and long exposure times. The degradation mechanism of m-LLDPE and ZN-LLDPE is similar; however, m-LLDPE showed a higher degradation rate than ZN-LLDPE of similar M_w and average SCB. ZN-LLDPE was found to be more stable than a similar m-LLDPE. Comonomer type had little influence on degradation. Dynamic shear rheology was very useful in revealing the influence of different molecular parameters and it exposed the degradation mechanism.     

Characterizing blends of linear low-density and low-density polyethylene by DSC

Summary A two-step isothermal annealing (TSIA) procedure is described that enables the endothermic peaks of low-density polyethylene (LDPE), linear low-density polyethylene (LLDPE) and their blends, to be satisfactorily resolved during analysis by differential scanning calorimetry. A modified form of multistep isothermal annealing, the TSIA procedure produces a highly characteristic profile of the blend components by facilitating the segregation of the phases based on branch density. It is proposed that the TSIA procedure may have significant merit in the identification and quantification of the components in an unknown blend as well as increasing the sensitivity in analytical procedures aimed at blend component quantification.     

UV stabilising synergies between carbon black and hindered light stabilisers in linear low density polyethylene films

The combined effects of selected carbon black pigments and hindered light stabilisers (HALS) on the UV stabilities of linear low density polyethylene film have been studied under UVA and UVB fluorescent radiation sources. While the presence of HALS do not change the chemistry of film photodegradation, whether they are low or high molecular variants, their presence significantly extends film lifetime relative to the sum of the effects of carbon black and HALS individually. These lifetime extensions may be defined in terms of a synergy factor defined with respect to film time to lose a specific percentage of a tensile property, namely t₂₀, the time to lose 20% of initial elongation-at-break, or the carbonyl index associated with this condition. It is proposed that possible causes of this synergy are a result of the UV screening effect of the carbon black particles which provide lower concentrations of polymer radicals for the HALS component to interact with and/or an accompanying thermal stabilising effect by the latter as a consequence of the higher polymer local temperature during irradiation of pigmented films.     

Restabilization of the aging resistance of compatibilized blends of pre-aged low density polyethylene and high-impact polystyrene (LDPE/HIPS)

Blends of pre-aged low density polyethylene (LDPE) with high-impact polystyrene (HIPS) compatibilized with a 1:1 mixture of styrene–butadiene block copolymer (SBS) and ethylene-propylene-diene statistical terpolymer (EPDM) were upgraded for thermooxidative resistance with N,N’-disubstituted 1,4-phenylenediamine. The impact strength after the oven test was improved. A model experiment confirmed that the efficiency of the phenylenediamine was not lost in the system after a partial sacrificial transformation of PD into the corresponding quinone diimine. The beneficial thermal effect of the upgrading used is a consequence of cooperation between the components of the blend. The system does not protect however against photooxidative stress without a suitable fortification with photostabilizers. The material properties of the upgraded blend upon oxidative stresses were assessed by monitoring of changes in the impact strength, carbonyl index and fracture surfaces on samples aged for various time intervals. It is shown that blends fortified by proper photostabilizers (carbon black or a combination of the UV absorber with photoantioxidant HAS) have sufficient stability for outdoor application.     

Effect of benzil and cobalt stearate on the aging of low-density polyethylene films

We report an investigation of the effect of benzil and cobalt stearate on the degradation behaviour of LDPE films. Thin films (70 μ) containing these additives were prepared by sheeting process. The effect of heating, exposure to UV-B and natural weathering of LDPE films in the presence/absence of additives was investigated. Changes in the tensile properties, carbonyl index and density were used to investigate the degradation behaviour. Attempts have been made to correlate the results as a function of mixed additives. In contrast to the activity of typical triplet activators, benzil was found to be incapable of initiating thermal- or photo-degradation of LDPE films. However, an accelerated rate of oxidation was observed, primarily due to cobalt stearate, in the case of compositions containing a combination of benzil and cobalt stearate. All samples were found to be more susceptible to thermo-oxidation than to UV or natural weathering.     

On the crystallinity effect on the gas sorption in semicrystalline linear low density polyethylene (LLDPE)

This article describes the solubility of carbon dioxide, ethylene and propane in 1‐octene based polyethylene of 0.94, 0.92, 0.904, and 0.87 densities. The isotherms obtained in the gas sorption experimental device display a sorption behavior similar to that of glassy polymers. We apply the dual model to semicrystalline polymers assuming that Henry's sites are related to the amorphous phase, which decreases when the crystallinity percentage increases, whereas the surface of the crystalline phase acts as a Langmuir site with higher gas‐polymer affinity than glassy polymers. The good concordance of the calculated k_D values, using the Flory‐Huggins theory of polymer diluent mixtures, with the experimental results suggest that Henry's gas sorption fulfills this theory and, therefore, it may be a suitable way to estimate polymer‐gas enthalpic interactions. Particularly, the variation of k_D with the crystallinity fraction is exponential and the proportionality of the total sorption with the amorphous content seems only apparent. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1798–1807, 2007     

Modification and photostabilization of low density polyethylene film by photodecomposition of various diazo-compounds and methyl azidocarboxylate

Various diazo-compounds, 1,2,2,6,6-pentamethylpiperidin-4-yl diazoacetate (PMPDA), 2,2,6,6-tetramethylpiperidin-4-yl diazoacetate (TMPDA), methyl diazoacetate (MDA), 1,2,2,6,6-pentamethylpiperidin-4-yl 2-diazo-3-methyloxycarbonylpropionate (PMPMDS), 1,2,2,6,6-pentamethylpiperidin-4-yl 2-diazo-4-methyloxycarbonylbutanoate (PMPMDP), and one azide, methyl azidocarboxylate (MAC), were successfully prepared and grafted on polyethylene films by UV light (λ > 210 nm) activation. The treated films were characterised by FT-IR spectroscopy and contact angle measurements. Ab-initio quantum mechanical calculations allowed simulating the IR absorption spectra of the polymer grafted species. These last and the related grafting yields are discussed with reference to the diazo-compound structure and concentration. Up to 8.6 mol% of bonded groups (grafted groups/ethylene monomeric unit) were found without affecting the polymer molecular weight distribution, as shown by GPC analysis. All modified films bearing HAS groups showed very high photo-stability.     

Preparation and physical properties of novel nonionic surfactants and their grafting copolymers with linear low density polyethylene (LLDPE)

Three nonionic surfactants, S1, S2, and S3 and their acrylates, AS1, AS2, and AS3, were synthesized with poly(ethylene oxide) and diols such as glycol, 1,6‐hexanediol, and 1,10‐decanediol as the main starting materials. Their chemical structures were characterized by means of Fourier transform infrared (FTIR) spectroscopy and ¹H NMR. The surface activity and surface tension (γ) of S1, S2, and S3 were evaluated by a drop weight method. The surface tension was found to decrease with the length of the lipophilic spacer in the molecular chains (γ_S1 < γ_S2 < γ_S3). AS1, AS2, and AS3 were adopted as functionalizing monomers and grafted onto linear low density polyethylene (LLDPE) with a melt reactive extrusion procedure. The graft degrees of LLDPE were determined by FTIR. Three grafted LLDPE samples with grafting degrees of 1.16% (AS1), 0.82% (AS2), and 0.71% (AS3) were prepared. Thermal and rheological properties of grafted LLDPE samples were studied with differential scanning calorimetry and a rotational rheometer. Crystallization rates of grafted LLDPE were faster than that of plain LLDPE at a given crystallization temperature because graft chains could act as nucleating agents. The isothermal crystallization behavior of grafted LLDPE was in accordance with the Avrami model only in the first stage, and deviated from the model with an increase in the crystallization time. Shear thinning at high shear rates and shear thickening at low shear rates were observed for the grafted LLDPE. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 314–322, 2005     

Thermal,tensile and rheological properties of linear low density polyethylene (LLDPE) irradiated by gamma-ray in different atmospheres

The aim of this paper is to investigate structural changes of linear low density polyethylene (LLDPE) modified by ionizing radiation (gamma rays) in different atmospheres. The gamma radiation process for modification of commercial polymers is a widely applied technique to promote new physical–chemical and mechanical properties. Gamma irradiation originates free radicals which can induce chain scission or recombination, providing its annihilation, branching or crosslinking. This polymer was irradiated with gamma source of ⁶⁰Co at doses of 5, 10, 20, 50 or 100 kGy at a dose rate of 5 kGy/h. The changes in molecular structure of LLDPE, after gamma irradiations were evaluated using thermogravimetric analyzer (TGA) and tensile machine and oscillatory rheology. The results showed the variations of the properties depending on the dose at each atmosphere.     

Laboratory accelerated and natural weathering of styrene-ethylene-butylene-styrene (SEBS) block copolymer

Indoor accelerated and outdoor weathering of polystyrene-b-(ethylene-co-butylene)-b-styrene (SEBS) was studied by infrared spectroscopy. Accelerated conditions involved simultaneous exposure of specimens to ultraviolet-visible radiation between 295 nm and 450 nm and each of four temperature/relative humidity (RH) environments, i.e., (a) 30 °C ± 1 °C at <1% RH, (b) 30 °C ± 1 °C at 80% RH, (c) 55 °C ± 1 °C at <1% RH, and (d) 55 °C ± 1 °C at 80% RH. Outdoor exposure was conducted in Gaithersburg, MD, in two different time periods. Similar photooxidative mechanisms were operative under all conditions. In the case of indoor accelerated exposure, the rate of photooxidation was found to depend strongly on temperature. Unlike the exposure at 55 °C, moisture-assisted photooxidation was insignificant at 30 °C. A quantitative study on the synergistic effect of environmental stressors revealed that the degrading effect of combined temperature and moisture on photooxidation was greater than the sum of the two effects exerted independently. Outdoor weathered specimens exhibited significantly slower photooxidation. Acceleration of photooxidation ranged from 2.5 to 10 times in comparison to the outdoor exposure, depending on the indoor accelerated conditions.