Carborane polymers. IV. Polysiloxanes

Carboranes attached to silicon through straight-chain alkyl groups were prepared and characterized for thermal stability by TGA and molecular weight change on heating. The monomers for these polymers were prepared generally by platinum-catalyzed addition of a silylhydride to an alkenyl or dialkenyl carborane. Polymerization was effected by hydrolysis-condensation of chlorosilanes, ring opening of cyclosiloxanes, and condensation of alkoxy and chlorosilanes. Two types of polymer structures were prepared, one contained m-carborane in the chain backbone, the other contained o-carborane as pendant alkylcarborane groups. Both types were obtained as elastomers; however, higher proportions of carborane in the polymers reduced elasticity and finally resulted in nonelastomers. TGA of the backbone carborane siloxane polymer indicated degradation at 370°C. in nitrogen and at 235°C. in air. Chain scission, as determined by molecular weight decrease, was observed on heating in nitrogen at 350°C. TGA of the pendant carborane siloxane polymer indicated that degradation in nitrogen and in air occurred at greater than 400°C. However, chain scission, as determined by molecular weight decrease, was observed upon heating at 300°C. in nitrogen.     

Study of the pyrolysis of municipal solid waste for the production of valuable products

To obtain information on the potential of thermal conversion (pyrolysis) of municipal solid waste (MSW), a thermogravimetric study (TGA) is performed in a stream of nitrogen. Based on TGA results, pyrolysis experiments are carried out in a semi-batch reactor under inert nitrogen atmosphere. Slow pyrolysis is performed up to 550 °C (heating rate of 4 °C/min). Fast pyrolysis is performed at 450, 480, 510 and 550 °C and different input transfer rates (12 or 24 g material/min). The pyrolysis products are studied on composition and yield/distribution and investigated for their use as valuable product.The liquid obtained by slow pyrolysis separates spontaneously in a water rich product and an oily product. For all fast pyrolysis conditions, a viscous, brown oil which contains a poly(ethylene-co-propylene) wax is obtained. Composition analyses by GC/MS of the oil products (slow/fast pyrolysis) show that aliphatic hydrocarbons are the major compounds. The pyrolysis oils have high calorific value (between 35 and 44 MJ/kg), low wt% of water (around 6 wt%) and a low O/C value (between 0.2 and 0.3). The presence of waxy material is probably due to incomplete breakdown of poly(ethylene-co-propylene) present in MSW under study. The optimal pyrolysis conditions, regarding to oil yield, fuel properties, and wax yield is fast pyrolysis at 510 °C with 24 g material/min input transfer rate. The fast pyrolysis gases contain mainly hydrocarbons and have an averaged LHV around 20 MJ/Nm³. ICP-AES analyses of pyrolysis products reveal that almost none of the metals present in MSW are distributed within the liquid fractions.     

Investigation of physicochemical properties of biooils produced from yellow poplar wood (Liriodendron tulipifera) at various temperatures and residence times

Fast pyrolysis of yellow poplar wood (Liriodendron tulipifera) was performed under different temperature ranges and residence times in a fluidized bed reactor to maximize the yield of biooil. In this study, the pyrolysis temperature ranged from 400 °C to 550 °C, and the residence time of pyrolysis products was controlled between 1.2 and 7.7 s by inert nitrogen gas flow. The results revealed that the distribution of thermal degradation products (biooil, biochar, and gas) from the woody biomass was heavily influenced by pyrolysis temperature, as well as residence time. The highest yield of biooil was approximately 68.5 wt% (wet basis), with pyrolysis conditions of 500 °C and 1.9 s of residence time. Water content of the biooils produced at different temperatures was 25-30 wt%, and their higher heating values were estimated to be between 15 MJ/kg and 17 MJ/kg. Using GC/MS analysis, 30 chemical components were identified from the biooil, which were classified into 5 main groups: organic acids, aldehydes, ketones, alcohols, and phenols. In addition, biochar was produced as a co-product of fast pyrolysis of woody biomass, approximately 10 wt%, at temperatures between 450 °C and 550 °C. The physicochemical features of the biochar, including elemental analysis, higher heating values, and morphological properties by SEM, were also determined.     

Pyrolysis behavior of phosphorus polyesters

The pyrolysis behavior of aromatic–aliphatic polyesters containing either a pendant 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) group or a phosphine oxide group incorporated into the polymer backbone was studied using a combination of thermogravimetry and pyrolysis-GC/MS. The behavior of the phosphorus polyesters was compared to that of non-phosphorus-containing reference polymers. It could be shown that the DOPO group mainly does not interfere with the polyester decomposition. It produces two main pyrolysis products, o-hydroxybiphenyl and dibenzofuran, with the latter one requiring a higher pyrolysis temperature. Minor products containing the DOPO ring result from secondary decomposition reactions. In contrast, the phosphine oxide group strongly modifies the polyester pyrolysis behavior by decreasing the degradation temperature and changing the composition of pyrolysis products. Among of those, phosphinites and a phosphinate could be identified indicating rearrangement processes of the phosphine oxide group taking place upon pyrolysis. Mass spectra of organophosphorus products and pyrolysis schemes of polyesters are discussed.     

Fluorescent aromatic polyamides with urea binding sites and fluorene or dansyl signaling units

This work describes six novel fluorescent aromatic polyamides with bulky dansyl or fluorene pendant groups or with the fluorene moiety in the main chain. The fluorescent signaling dansyl or fluorene moieties are chemically connected to, or within, the main polymer chains through a urea group, a well-known binding site in supramolecular chemistry. These polyamides are amorphous and soluble in polar aprotic solvents and demonstrate a film-forming capability. They also show yellowish-green or blue fluorescence in solution and in the solid state depending on the signaling unit, with the former corresponding to the dansyl and the latter to the fluorene residue. The water uptake and the thermal behavior have also been evaluated and related to the chemical structure. The polar amide, urea, and sulfonamide groups give rise to a high water sorption of up to 3.8 water molecules per repeating unit. The thermal behavior has been investigated by means of DSC and TGA. The glass transition temperatures of the polymers are high (up to 331 °C) and the decomposition temperatures (around 300 °C) are due to the moderate thermal stability of the urea group.     

A review of heat treatment on polyacrylonitrile fiber

Developing carbon fiber from polyacrylonitrile (PAN) based fiber is generally subjected to three processes namely stabilization, carbonization, and graphitization under controlled conditions. The PAN fiber is first stretched and simultaneously oxidized in a temperature range of 200-300 °C. This treatment converts thermoplastic PAN to a non-plastic cyclic or a ladder compound. After oxidation, the fibers are carbonized at about 1000 °C in inert atmosphere which is usually nitrogen. Then, in order to improve the ordering and orientation of the crystallites in the direction of the fiber axis, the fiber must be heated at about 1500-3000 °C until the polymer contains 92-100%. High temperature process generally leads to higher modulus fibers which expel impurities in the chain as volatile by-products. During heating treatment, the fiber shrinks in diameter, builds the structure into a large structure and upgrades the strength by removing the initial nitrogen content of PAN precursor and the timing of nitrogen. With better-controlled condition, the strength of the fiber can achieve up to 400 GPa after this pyrolysis process.     

Controlled radical polymerization of cholesteryl acrylate and its block copolymer with styrene via the RAFT process

Reversible addition fragmentation chain transfer (RAFT) polymerization of cholesteryl acrylate (ChA) was conducted using S-1-dodecyl-S′-(α,α′-dimethyl-α′′-acetic acid)trithiocarbonate as CTA and AIBN as initiator in toluene at 80 °C. The polymerization was investigated at two different CTA concentrations (0.025 and 0.040 M). Polymerization of ChA with CTA concentration of 0.040 M proceeds in a controlled/living manner as evidenced by linear increase of the molecular weight with conversion and narrow polymer polydispersity (PDI < 1.2). With lower initial CTA concentration, namely 0.025 M, although poly(cholesteryl acrylate) (PChA) exhibiting narrow molecular weight distributions could be synthesized, the polymerization showed relatively low control with many termination products. Chain extension polymerizations were performed starting from either the PChA or the polystyrene (PS) block, and well-defined copolymers based on ChA and styrene were prepared. Thermal properties of PChA and PS-b-PChA copolymer were investigated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), and the results showed that both PChA and PS-b-PChA are amorphous polymers. PChA begins to decompose at ca. 218 °C with maximum weight loss rate at 351 °C, while PS-b-PChA shows double weight loss rate peaks located at 345 and 415 °C, respectively.     

Polyhydrazides based on 2,5-bis(4-carboxymethylene phenyl)-3,4-diphenyl thiophene

A series of polyhydrazides was synthesized from a novel dicarboxylic acid, 2,5-bis(4-carboxymethylene phenyl)-3,4-diphenyl thiophene (V) and or terephthalic acid and isophthaloyl or terephthaloyl dihydrazide by Yamazaki’s phosphorylation method using triphenyl phosphite as condensing agent. Polyhydrazides were characterized by IR spectroscopy solubility, viscosity, thermogravimetric analysis and X-ray diffraction studies.The polymers were obtained in quantitative yields. Polyhydrazides had viscosities in the range of 0.25-0.70 dL/g. The polymers derived from novel diacid (V) showed enhanced solubility than the polymers derived from terephthalic acid, which may be attributed to the presence to bulky pendant phenyl group and methylene spacer group in the polymer backbone. Polymers were soluble in most of the common aprotic polar solvents. Polyhydrazides showed considerable weight loss in the temperature range of 300-400 °C which is due to the cyclodehydration, leading to the formation of corresponding polyoxadiazoles. They showed T_max in between 500 and 600 °C which is essentially the decomposition of the polyoxadiazoles. X-ray diffraction studies showed that polyhydrazides were amorphous in nature.     

Thermal decomposition products of copoly(arylene ether sulfone)s characterized by direct pyrolysis mass spectrometry

Pyrolysis products with mass of up to 850 Da were detected by direct pyrolysis mass spectrometric (DPMS) analysis of a series of copoly(arylene ether sulfone)s (PES-PPO) synthesized by nucleophilic condensation of either 4,4′-dichlorodiphenylsulfone (CDPS) or 4,4′-bis-(4-chlorophenyl sulfonyl) biphenyl (long chain dichloride, LCDC) with different molar ratios of hydroquinone (HQ) or dihydroxydiphenylsulfone (HDPS). Pyrolysis products retaining the repeating units of the initial copolymers were formed at temperatures ranging from 420 °C to 470 °C (near the initial decomposition temperature). At temperatures higher than 450 °C were observed products containing biphenyl units, formed by the elimination process of SO₂ from diphenyl sulfone bridges. Products having biphenyl and dibenzofuran moieties were detected in the mass spectra recorded at temperatures above 550 °C. These units were formed by loss of hydrogen atom from diphenyl ether bridges. Although the EI (18 eV) mass spectra of the pyrolysis products of the samples investigated were very similar, it was found that the relative intensity of some ions reflects the molar composition of the copolymers analysed. Cyclic and linear oligomers with very low molecular mass, present in the crude copolymers, were also detected by DPMS. Thermogravimetric analysis also showed their excellent thermal stability below 400 °C. It indicates that the copolymers yield a char residue of 40-45% at 800 °C, which increases with the PPO mole fraction in the samples.     

Gas- and solid/liquid-phase reactions during pyrolysis of softwood and hardwood lignins

Pyrolytic reactions of Japanese cedar (Cryptomeria japonica, a softwood) and Japanese beech (Fagus crenata, a hardwood) milled wood lignins (MWLs) were studied with thermogravimetry (TG) and by pyrolysis in a closed ampoule reactor (N₂/600 °C). The data were compared with those of guaiacol/syringol as simple lignin model aromatic nuclei. Several DTG peaks were observed around 300-350, 450, 590 and 650 °C. The first DTG peak temperature (326 °C) of beech was lower than that (353 °C) of cedar. This indicates that the volatile formation from cedar MWL is slightly delayed in heating at 600 °C. The gas-phase reactions via GC/MS-detectable low MW products were explainable with the temperature-dependent reactions observed for guaiacol/syringol in our previous paper. The methoxyl groups became reactive at ∼450 °C, giving O-CH₃ homolysis products (catechols/pyrogallols) and OCH₃ rearrangement products (cresols/xylenols). The former homolysis products were effectively converted into gaseous products (mainly CO) at >550-600 °C. However, the GC/MS-detectable tar yields, especially syringyl unit-characteristic products, were much lower than those from guaiacol/syringol. Thus, contributions of higher MW intermediates and solid/liquid-phase reactions are more important in lignin pyrolysis. From the results of stepwise pyrolysis of char + coke fractions at 450 and 600 °C, the methoxyl group-related reactions (450 °C) and intermediates gasification (600 °C) were suggested to occur also in the solid/liquid phase. This was consistent with the DTG peaks observed around these temperatures. These solid/liquid-phase reactions reduced the tar formation, especially catechols/pyrogallols and PAHs. Different features observed between these two MWLs are also focused.     

Thermal reactions of guaiacol and syringol as lignin model aromatic nuclei

Thermal reactions of guaiacol (2-methoxyphenol) and syringol (2,6-dimethoxyphenol) were compared in a closed ampoule reactor (N₂/400-600 °C/40-600 s) to obtain information on the thermal reactivities of lignin aromatic nuclei, guaiacyl and syringyl types. For both compounds, the O-CH₃ bond homolysis, which was observed at >400 °C, initiated their decomposition. This homolysis was followed by several temperature-dependent reactions; radical-induced rearrangement to convert the aromatic OCH₃ to aromatic CH₃ structures and condensation into high molecular weight (MW) products were the next steps (≈400 °C); then, coke formation became extensive (≈450 °C); effective gas formation required higher temperature such as >550-600 °C. The syringol- and guaiacol-characteristic GC/MS-detectable low MW products were explained with the above mentioned reactions. As for the difference between guaiacol and syringol, coke and gas (especially CH₄ and CO₂) formation was more extensive in syringol. This effective coking can be explained by the influence of the additional OCH₃ group in syringol, which doubles the opportunity for coke formation. This, in turn, reduces the yields of GC/MS-detectable low MW products. Demethoxylation to form guaiacol was also observed in syringol, even though the reactivity was not so high. These reactions are discussed at the molecular level.     

Physical properties of films made of copoly(ether-imide)s with long poly(ethylene oxide) segments

Polyimides having long poly(ethylene oxide), PEO, moieties in the main chain have been synthesized by a classical two-steps polycondensation method with good yield and high molecular weight. In contrast with previous works on this topic, essentially full conversion of the polyamic acid to polyimide was attained by heating at relatively low temperatures (around 160 °C).These copolyimides undergo an increase of phase separation between the PEO part and the polyimide one after a thermal annealing. This phase separation increases gas separation properties of membranes made up of these copolymers. An exhaustive study of polymer properties as a function of the thermal treatment has been carried out in order to figure out the origin of this behavior. The analysis performed included TGA, DSC, SAXS and mechanical testing.The polymers studied in this paper have medium thermal stability. In fact, degradation of the polyether chain under nitrogen takes place at temperatures above 300 °C. However, their thermal stabilities were much lower under oxidant atmosphere.     

Thermal degradation mechanism of flame retarded epoxy resins with a DOPO-substitued organophosphorus oligomer by TG-FTIR and DP-MS

A novel phosphorus-containing oligomeric flame retardant, poly(DOPO substituted hydroxyphenyl methanol pentaerythritol diphosphonate) (PDPDP) was synthesized and applied to flame retarded epoxy resins. The thermal degradation behaviors of flame retarded epoxy composites with PDPDP were investigated by thermogravimetric analysis (TGA), thermogravimetric analysis/infrared spectrometry (TG-FTIR) and direct pyrolysis-mass spectrometry (DP-MS) techniques. The identification of pyrolysis fragment ions provided insight into the flame retardant mechanism. The results showed that the mass loss rate of the EP/PDPDP composites was clearly lower than pure EP when the temperature was higher than 300 °C in air or nitrogen atmosphere. The results also suggested that the main decomposition fragment ions of the EP/PDPDP composite were H₂O, CO₂, CO, benzene, and phenol. The incorporation of PDPDP can reduce the release of combustible gas and induce the formation of char layer, hence the fire potential hazard was reduced.     

Synthesis and characterization of new polyimides containing ethynylene linkages

We have synthesized a series of new diamines containing bis(ethynylaniline) linkages by bromine substitution reaction of ethynylaniline with 4,4′-bis(4-bromophthalimido)diphenylether (PODA) or 1,4-bis(4-bromophthalimido)benzene (PPDA). The intermediates were separated at each step, purified and characterized by the spectroscopic techniques. The model compound having imide and triple bond moiety was synthesized in order to elucidate the nature of the products formed from the ethynyl curing by FT-IR spectroscopy. The polymerization reaction of ethynylaniline diamines with various dianhydrides gave fully imidized and soluble aromatic polyimides. The thermally cured polyimide samples displayed good solvent resistance. The thermal crosslinking of triple bond moieties in the main chain was carried out by heating in the temperature range from 150 to 400 °C. The glass transition temperature of polyimide completely disappeared after heat treatment at 400 °C for 5 min. The polyimides derived from diamines containing bis(ethynylaniline) groups were thermally stable after heat treatment.     

The effects of thermal treatment on the antioxidant activity of polyaniline

The thermal stability of chemically synthesized polyaniline (PANI) was examined, including granular (G) polyaniline powders formed conventionally in an HCl medium, and nanorod (NR) samples prepared using a falling-pH synthesis. The samples were examined before and after dedoping (dd) using thermogravimetric analysis (TGA), which showed small mass losses in the 200-300 °C temperature range, and greater mass losses due to oxidative degradation at higher temperatures. Furthermore, samples were treated thermally at 100, 125, 150, 175, 200, 250 and 300 °C for 30 min in air. SEM images did not show any pronounced effect on the morphologies of the samples from thermal treatment up to 300 °C. The ratios of the intensities (Q/B) of the predominantly quinonoid (Q) and benzenoid peaks (B) from FTIR spectroscopic analysis revealed that NR-PANI and NR-PANIdd underwent cross-linking upon thermal treatment up to 175 °C and were oxidized after treatment above 175 °C. G-PANI and G-PANIdd also underwent the same chemical changes with oxidation occurring above 200 °C. The free radical scavenging capacity of the samples was evaluated using the 1,1-diphenyl-2-picrylhydrazyl (DPPH) assay, and was found to be independent of the spin concentrations of the samples. All samples exhibited a rapid decline in free radical scavenging capacity when exposed to temperatures above 200 °C, indicating that any polymer processing should be undertaken at temperatures less than this value to achieve high antioxidant activity.     

Physico-mechanical, thermal and morphological behaviour of polyurethane/poly(methyl methacrylate) semi-interpenetrating polymer networks

Semi-interpenetrating polymer networks (SIPNs) of polyurethane (PU) and poly(methyl methacrylate) (PMMA) in different weight ratios viz., 90/10, 70/30, 60/40 and 50/50 were prepared. The SIPNs were characterized for physico-mechanical properties like density, tensile strength and elongation at break. Thermal stability of IPNs was measured using thermogravimetric analysis (TGA). From the TGA thermograms it was noticed that all IPNs are stable up to 325 °C and undergo three-step thermal degradation in the temperature ranges 251-400, 378-508 and 445-645 °C for first, second and third steps, respectively. Thermal degradation kinetic parameters like activation energy (E_a) were calculated using Broido, Coats-Redfern and Horowitz-Metzger models. The values obtained by Broido and Horowitz-Metzger methods showed concurrency, whereas Coats-Redfern method showed relatively lower values. Surface morphology measured using scanning electron microscope (SEM) showed two-phase morphology for all the IPNs.     

A pyrolysis-GC–MS investigation of poly(vinyl phenyl ketone)

The thermal decomposition process and pyrolysis products of poly(vinyl phenyl ketone) (PVPK) were investigated by thermogravimetric analysis (TGA) and on-line pyrolysis-gas chromatography–mass spectrometry (Py-GC–MS). TGA showed a largest weight loss rate around 380 °C. Py-GC–MS was used for the qualitative analysis of the pyrolysis products at 350, 500, 600, 700 and 850 °C. The major volatile thermal decomposition product was found to be 1-phenyl-2-propenone, which dominated all other volatile species especially under the least severe pyrolysis conditions (<600 °C). At higher temperatures a much wider range of pyrolysis products was obtained. The results have been interpreted assuming that primary random chain scission reactions occur followed by typical unzipping mainly producing monomer units; detachment of the side-group occurs only under more severe pyrolysis conditions. Py-GC–MS showed to be effective in PVPK detection in ink and paint formulations.     

The thermal degradation of poly(vinyl acetate) and poly(ethylene-co-vinyl acetate), Part I: Experimental study of the degradation mechanism

The thermal degradation mechanism of poly(vinyl acetate) (PVAc) and poly(ethylene-co-vinyl acetate) (EVA) copolymers was investigated with solid-state NMR, thermogravimetry coupled with mass spectrometry and differential thermal analysis. Between 300 and 400 °C acetic acid is eliminated (deacetylation), leaving a highly unsaturated residue or polyene. The deacetylation of PVAc is autocatalytic. Upon incorporation of ethylene entities into the polymer backbone, autocatalysis disappears. Between 400 and 500 °C, the polyene will degrade further by chain scission reactions in inert conditions or aromatise in an oxidative environment into a char, and oxidised eventually into CO₂ beyond 500 °C.In inert conditions, the deacetylation step as well as the chain scission reaction shows endothermic effects. In an oxidative environment, large exothermal effects are found for each degradation step. This indicates the occurrence of additional oxidation reactions during deacetylation, an important reorganisation of the polyene during char formation and oxidation of the latter into CO₂.     

Degradation of polycaprolactone in supercritical fluids

The degradation of polycaprolactone (PCL) was studied in subcritical and supercritical toluene from 250 to 375 °C at 50 bar. The degradation was also investigated in various solvents like ethylbenzene, o-xylene and benzene at 325 °C and 50 bar. The effect of pressure on degradation was also evaluated at 325 °C at various pressures (35, 50 and 80 bar). The variation of molecular weight with time was analyzed using gel permeation chromatography and modeled using continuous distribution kinetics to evaluate the degradation rate coefficients. PCL degrades by random chain scission in subcritical conditions (250-300 °C) and by chain end scission (325-375 °C) in supercritical conditions in toluene. The degradation of PCL in other solvents at 325 °C was by chain end scission under both subcritical and supercritical conditions indicating that the mode of scission depends on the temperature and not on the supercriticality of the solvent. The thermogravimetric analysis of PCL was investigated at various heating rates (2-24 °C/min) and the activation energy was determined using Friedman, Ozawa and Kissinger methods. It was shown that PCL degrades by random scission at lower temperatures and by chain end scission at higher temperatures again indicating that the mode of scission is dependent on the temperature.     

Commercial fire-retarded PET formulations - Relationship between thermal degradation behaviour and fire-retardant action

Many types of fire retardants are used in poly(ethylene terephthalate), PET, formulations, and two commercial fire retardants, Ukanol^® and Phosgard^®, have been shown to improve significantly PET flame-retardancy when used as comonomers. Phosgard incorporates a phosphorus atom within the main chain whereas Ukanol incorporates a phosphorus atom as a pendent substituent. Despite their acknowledged effectiveness, the mode of action of these fire retardants remains unclear, and in this paper we present a comparison of the overall thermal degradation behaviour of PET and Ukanol and Phosgard fire-retarded formulations. DSC and particularly TGA data show that both Ukanol and Phosgard have some stabilising influence on PET degradation, especially under oxidative conditions. TGA and pyrolysis experiments both clearly indicate that neither of the additives acts as a char promoter. Only the Phosgard formulation shows any release of volatile phosphorus species which could act in the gas phase. On the other hand, the most striking feature of the pyrolysis experiments is the macroscopic structure of the chars produced by the fire-retarded formulations, which hints at their fire-retardancy action - an open-cell charred foam was obtained upon charring at 400 °C or 600 °C. This foaming layer between the degrading melt and the flame would lower the amount of fuel available for combustion, and would also limit the feedback of heat to the condensed phase.