Biosynthesis and characterization of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) copolymer from wild-type Comamonas sp. EB172

Poly(3-hydroxybutyrate) [P(3HB)] homopolymer and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) [P(3HB-co-3HV)] copolymer was produced by Comamonas sp. EB172 using single and mixture of carbon sources. Poly(3-hydroxyvalerate) P(3HV) incorporation in the copolymer was obtained when propionic and valeric acid was used as precursors. Incorporation of 3HV fractions in the copolymer varied from 45 to 86 mol% when initial pH of the medium was regulated. In fed-batch cultivation, organic acids derived from anaerobically treated palm oil mill effluent (POME) were shown to be suitable carbon sources for polyhydroxyalkanoate (PHA) production by Comamonas sp. EB172. Number average molecular weight (M_n) produced by the strain was in the range of 153-412 kDa with polydispersity index (M_w/M_n) in the range of 2.2-2.6, respectively. Incorporation of higher 3HV units improved the thermal stability of P(3HB-co-3HV) copolymer. Thus the newly isolated bacterium Comamonas sp. EB172 is a suitable candidate for PHA production using POME as renewable and alternative cheap raw materials.     

Improved synthesis of P(3HB-co-3HV-co-3HHx) terpolymers by mutant Cupriavidus necator using the PHA synthase gene of Chromobacterium sp. USM2 with high affinity towards 3HV

Unlike polyhydroxyalkanoates (PHAs) copolymers, the controlled and efficient synthesis of PHA terpolymers from triglycerides and fatty acids are yet to be established. This study demonstrates the production of P(3HB-co-3HV-co-3HHx) terpolymer with a wide range of 3HV monomer compositions from mixtures of crude palm kernel oil and 3HV precursors using a mutant Cupriavidus necator PHB⁻4 transformant harboring the PHA synthase gene (phaC) of a locally isolated Chromobacterium sp. USM2. The PHA synthase of Chromobacterium has an unusually high affinity towards 3HV monomer. P(3HB-co-3HV-co-3HHx) terpolymers with 3HV monomer composition ranging from 2 to 91 mol% were produced. Generation of 3HHx monomers was affected by the concentration and feeding time of 3HV precursor. P(3HB-co-24 mol% 3HV-co-7 mol% 3HHx) exhibited mechanical properties similar to that of common low-density polyethylene. P(3HB-co-3HV-co-3HHx) terpolymers with a wide range of 3HV molar fraction had been successfully synthesized by adding lower concentrations of 3HV precursors and using a PHA synthase with high affinity towards 3HV monomer.     

Changes in the mechanical properties of compression moulded samples of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) degraded by Streptomyces omiyaensis SSM 5670

Streptomyces omiyaensis SSM 5670 was characterized by its ability to use compression moulded samples of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) as its sole carbon source. Biodegradation of PHBV in liquid mineral salts medium was investigated using scanning electron microscopy, gravimetric measurements, capillary viscometry, tensile testing and wide angle X-ray spectroscopy. The biodegradation of PHBV proceeds via surface erosion mechanism, resulting in the formation of pits by microbial attack. PHBV specimens lost about 45% of their original weight after 45 days of exposure. During the degradation process the elastic modulus reduces less than 10%. The formation of pores and microcracks initiated at the degraded pits determines the reduction of the elongation and stress at break. However, the true stress at break is practically independent of the degradation time. No significant changes of PHBV molecular weight or crystallinity were observed during biodegradation. The polymer chain cleavage occurred only at the specimen surface and does not discriminate between crystalline and amorphous states.     

Characterization of biosynthesized P(3HB-co-3HA)s swellable in organic solvents

Polyhydroxyalkanoate (PHA) copolymers consisting of (R)-3-hydroxybutyrate (3HB) and medium-chain-length (R)-3-hydroxyalkanoate (3HA), P(3HB-co-3HA), are usually solved in chloroform. However, we found that some of the P(3HB-co-3HA) aged for more than 1 month under ambient conditions were not solved in chloroform, but instead swelled when the 3HA fraction was over 14 mol%. On the basis of differential scanning calorimetry and wide-angle x-ray diffraction analyses, we predicted that swellable P(3HB-co-3HA) contained numerous P(3HB) microcrystals, which may form physical crosslinks between adjacent PHA polymer chains.     

Mechanical properties, structure analysis and enzymatic degradation of uniaxially cold-drawn films of poly[(R)-3-hydroxybutyrate-co-4-hydroxybutyrate]

Poly[(R)-3-hydroxybutyrate-co-4-hydroxybutyrate] (P(3HB-co-4HB)) films were prepared by uniaxial cold-drawing from an amorphous preform at a temperature below, but close to the glass transition temperature. Molecular and highly-ordered structures and physical properties of cold-drawn films were investigated by tensile testing, wide-angle X-ray diffraction and small-angle X-ray scattering. Enzymatic degradation of P(3HB-co-4HB) films was performed using an extracellular polyhydroxybutyrate depolymerase purified from Ralstonia pickettii T1. Tensile strength, elongation to break and Young’s modulus of P(3HB-co-4HB) with cold-drawn ratio 1200% reached 290 MPa, 58% and 2.8 GPa, respectively. X-ray fibre diagrams of cold-drawn P(3HB-co-4HB) films showed a strong reflection on the equatorial line, indicating a planar zigzag conformation (β-form) together with 2₁ helix conformation (α-form). The β-form seems to contribute to the high tensile strength, and a new mechanism of generation of the β-form is proposed. The enzymatic degradation rate increased with increasing draw ratio, and increased greatly with increasing 4HB content.     

Thermal degradation and their kinetics of biodegradable poly(butylene succinate-co-butylene terephthate)s under nitrogen and air atmospheres

In this study, thermal degradation and their related kinetics have been investigated mainly by means of thermal gravimetrical analyzer (TGA) under the dynamic nitrogen and air atmospheres for the chemically prepared biodegradable aliphatic-aromatic copolyesters of poly(butylene succinate-co-butylene terephthalate) (PBST). To further shed new lights on the comonomer molar composition and experimental condition dependences of thermal degradation kinetics, the as-known Friedman model was at first applied to quantitatively evaluate the kinetic parameters in terms of activation energy (E), degradation reaction order (n) and the frequency factor (Z). The results clearly demonstrated that thermal stabilities of these PBST copolyesters were substantially enhanced with the incorporation of more rigid butylene terephthalate comonomer, and tended to be much better in nitrogen than in air. Furthermore, the Friedman, Freeman-Carroll and Chang models were concurrently employed to quantitatively evaluate the thermal degradation kinetic parameters of the PBST copolyesters in nitrogen at different heating rates of 1, 2 and 5 K/min. It was found that the thermal degradation kinetic parameters for the PBST copolyesters were strongly dependent on the heating rate and calculating models. In addition, life-time parameters of the biodegradable PBST copolyesters were first calculated to predict the maximum usable temperatures, and this would be useful for practical application of these new bio-based green plastics.     

The morphological effects upon enzymatic degradation of poly(butylene succinate-co-butylene terephthalate)s (PBST)

In this work, the enzymatic degradation of poly(butylene succinate-co-butylene terephthalate) (PBST) copolyesters was studied using the lipase from Pseudomonas (Lipase PS^®). The biodegradation behavior was found to strongly depend on the overall impacts of several important factors as the BT comonomer structure and molar content, thermal characteristics, morphology, the enzyme-substrate, and so forth. Further, the biodegraded residual film samples were allowed to be analyzed by means of gel permeation chromatography (GPC), proton nuclear magnetic resonance (¹H NMR), differential scanning calorimeter (DSC), small angle X-ray scattering (SAXS), and scanning electron microscope (SEM). On the experimental evidences, an exo-type mechanism of enzymatic chain hydrolysis preferentially occurring in the amorphous region was suggested for the PBST film samples.     

Effect of the permeants/polymer interactions on the pervaporative separation properties of the P(VDF-co-HFP) membrane

In this paper, the acetone-cast poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-co-HFP)) membranes were prepared by isothermally vacuum-dried at 60 °C and were employed in pervaporation of methyl acetate (MeAc) or ethyl acetate (EtAc) dissolved water solutions. DSC study on the swelling process indicated that two states of both MeAc and EtAc in their swollen P(VDF-co-HFP) membranes might exist which were the ‘bound state’ and ‘bulk state’. In addition, relative to the pure EtAc, the pure MeAc had stronger interaction with the P(VDF-co-HFP) membrane, making for its higher solubility in and lower diffusivity through the membrane. However, there is a competition between the organic permeants/water interactions and the organic permeants/polymer interactions when the P(VDF-co-HFP) membrane was tested for its pervaporative separating properties. With respect to MeAc in its water mixtures, EtAc in its water mixtures had higher solubility in the membrane instead because of its weaker interaction with water. As a result, better separating properties (higher permeate flux and separation factor) when the P(VDF-co-HFP) membrane was in pervaporation of the EtAc/water mixtures were obtained.     

Engineering of pha operon on Cupriavidus necator chromosome for efficient biosynthesis of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) from vegetable oil

Cupriavidus necator H16C_Ac, previously constructed for production of poly((R)-3-hydroxybutyrate-co-(R)-3-hydroxyhexanoate) [P(3HB-co-3HHx)] from soybean oil, was further engineered aiming to increase 3HHx composition in the copolyester. PHA synthase gene derived from Aeromonas caviae on the H16C_Ac chromosome was replaced by a gene encoding the N149S/D171G mutant and this recombination enhanced PHA productivity as well as slightly increased 3HHx composition. Manipulation of phaA_Cn locus partially reduced the amount of 3HB unit concomitantly with relative increase of 3HHx composition, whereas deletion of phaB1_Cn resulted in drastic decline of 3HB unit in P(3HB-co-3HHx). Insertion of phaJ_Ac encoding (R)-specific enoyl-CoA hydratase from A. caviae into pha operon significantly enlarged 3HHx fraction without negative effects on the cell growth and polyester accumulation. Consequently, efficient production of P(3HB-co-3HHx) with 3HHx composition of 5.7-9.9 mol% was successfully achieved from soybean oil by the engineered strains.     

n-Hexane sorption in poly(ethylene-co-1-octene)s: Effect on phase composition and character

Diffusion of small-molecule penetrants in semi-crystalline polymers is retarded by two factors: penetrant detour bypassing impenetrable crystals and the constraining effect of the crystals on the amorphous component. Previous experiments have shown that the latter factor becomes much less important at higher penetrant concentration in the polymer. Structural changes in a series of poly(ethylene-co-1-octene)s occurring on saturation in n-hexane at 296 K, covering a wide range of crystallinity (17-75 wt.%), were studied by wide-angle X-ray scattering, Raman spectroscopy and NMR spectroscopy. Densification of the crystal unit cell and partial dissolution of the interfacial component on n-hexane sorption are the main experimental findings. The conclusion is that the penetrant molecules increase the mobility of the polymer chain segments adjacent to the crystal interface, enabling better packing of the crystal stems and importantly also causes a reduction in the constraining factor (β) for diffusion.     

Biodegradation of microbial polyesters P(3HB) and P(3HB-co-3HV) under the tropical climate environment

The biodegradation of poly(3-hydroxybutyrate), P(3HB), and its copolymer poly(3-hydroxybutyrate-co-3-hydroxyvalerate), P(3HB-co-3HV) produced by a locally isolated bacteria identified as Erwinia sp. USMI-20 were carried out by using soil burial test and immersion test method at various places under the tropical environment in West Sumatra, Indonesia. The isolation of P(3HA)-degrading microorganisms was done by the in vitro rapid plate test method and was further characterized by using biochemical reactions. Our results showed that P(3HB) biodegraded at a rate of 3.6% per week in activated sludge, 1.9% per week in soil, 1.5% per week in lake water and 0.8% per week in Indian Ocean sea water. The degradation rates for P(3HB-co-3HV) were 17.8% per week in activated sludge, 6.7% per week in soil, 3.2% per week in lake water and 2.7% per week in Indian Ocean sea water. The biodegradation of both polymers were highest after burial into activated sludge with a half-life (T_1/2) of 14 weeks and the time for 100% degradation (T_100%) of 28 weeks for P(3HB), and a T_1/2 of 3 weeks and T_100% at 6 weeks for P(3HB-co-3HV). In this study, 10 bacteria which were responsible for the biodegradation of P(3HB) and P(3HB-co-3HV) film were isolated and identified from the various places studied under the tropical environment. They were Bacillus sp. FAAC-2202, Enterobacter sp. FAAC-2207, Bacillus sp. FAAC-2209 and Proteus sp. FAAC-2203 obtained from activated sludge, Bacillus sp. FAAC-2201 and Alcaligenes sp. FAAC-2210 from soil, Alcaligenes sp. FAAC-2205, Micrococcus sp. FAAC-2206 and Pseudomonas sp. FAAC-2208 from lake water and Proteus sp. FAAC-2204 from Indian Ocean sea water.     

Stereoselective synthesis of (E)-β-arylvinyl bromides by microwave-induced reaction of anti-3-aryl-2,3-dibromopropanoic acids using an AgOAc-AcOH system

(E)-β-Arylvinyl bromides were stereoselectively prepared in high yields by microwave irradiation of the corresponding anti-3-aryl-2,3-dibromopropanoic acids in AcOH in the presence of AgOAc for 0.5-3.0 min.     

Morphology of polystyrene-block-poly(styrene-co-acrylonitrile) and polystyrene-block-poly(styrene-co-acrylonitrile-co-5-vinyltetrazole) diblock copolymers prepared by nitroxide-mediated radical polymerization and “click” chemistry

Well-defined polystyrene-block-poly(styrene-co-acrylonitrile) PS-block-P(S-co-AN) and poly(styrene-co-acrylonitrile-co-5-vinyltetrazole) PS-block-P(S-co-AN-co-5VT) block copolymers with various content of acrylonitrile units in the statistical block were synthesized by nitroxide mediated radical polymerization (NMRP) and post-functionalized using efficient “click” chemistry process. In the second step, acrylonitrile units were successfully modified using 1,3-dipolar cycloaddition (“click” chemistry) type polymer analogue reaction. The original pristine diblock copolymers can be molecularly dissolved in THF and dioxane while the “tetrazolated” versions aggregate to clusters as determined by dynamic light scattering (DLS). Small-angle X-ray scattering (SAXS) and Transmission Electron Microscopy (TEM) revealed ordered lamellar morphology with interlamellar spacing d = 60 nm increasing to d = 80 nm for “tetrazolated” diblock copolymers. The morphological features of diblock copolymer thin layers observed by Atomic Force Microscopy (AFM) depend on the tunable content of both acrylonitrile and 5-vinyltetrazole units and on the quality (polarity) of the solvents used.     

十八烷/聚(St-MMA)相变微胶囊制备及表征

采用乳液聚合的方法,分别选取聚苯乙烯(PS)、聚甲基丙烯酸甲酯(PMMA)或苯乙烯和甲基丙烯酸甲酯的共聚物为壁材,正十八烷为芯材,十二烷基苯磺酸钠(SDBS)为乳化剂,制作相变储能微胶囊。用粒径分析仪、透射电子显微镜(TEM)、热重分析仪(TG)和示差扫描量热测试仪(DSC)对微胶囊的形貌、相变热性能和热稳定性分别进行表征。结果表明:壁材选取两者共聚物,当两种单体的比例为St∶MMA=1∶5,SDBS用量为1.5g(总质量的3%)时,微胶囊粒径大小均匀,粒子分散性好,壁材的包裹性好。微胶囊的放热峰为起始温度为27.3℃,终止温度为31.9℃,相变温度为28.9℃,相变焓为48.4J/g。TG表明长期使用温度不能超过131℃。IR分析微胶囊中含有芯材和壁材。这种十八烷/聚(St-MMA)相变微胶囊可以用于诸能材料。     

Cyclization of C-phosphorylated (P) arylformamidines to 3H-1,3-benzazaphospholes

A synthesis of 3H-1,3-benzazaphospholes starting from C-phosphorylated P(III) arylformamidines has been developed. Electron-donating substituents were found to enhance markedly the rate of the cyclization, with substituents at the meta position having the greatest effect. A plausible mechanism of the cyclization was proposed based on DFT calculations.     

Preparation of poly(lactide-co-glycolide-co-caprolactone) nanoparticles and their degradation behaviour in aqueous solution

The tri-component copolymer poly(lactide-co-glycolide-co-caprolactone) (PLGC) was synthesized to prepare nanoparticles by the modified spontaneous emulsification solvent diffusion method (modified-SESD method); and the method was also modified by using the Tween60 instead of poly(vinyl alcohol) (PVA) as dispersing agent. The obtained nanoparticles have spherical shape and good particle distribution with mean size in the range from 100 to 200 nm. The in vitro degradation behaviour of PLGC nanoparticles was investigated. It was found that PLGC nanoparticles could remain stable during the degradation with no agglomeration. Compared with PLA and PLGA nanoparticles, the degradation rate of PLGC nanoparticles is faster. After 9 weeks of hydrolysis, the M_n of PLGC is less by 10% of the original M_n. The mean radius of the nanoparticles increases from 68 nm to 80 nm continuously during the first stage, and after 4 weeks of degradation, the particles' size decreases gradually from 80 nm to about 40 nm. These results suggest that the PLGC nanoparticles may show degradation-controlled drug release behaviour and seem to be a promising drug delivery system.     

Preparation of telechelic oligomers by controlled thermal degradation of isotactic poly(1-butene) and poly(propylene-ran-1-butene)

It was found that telechelic isotactic oligo(1-butene) and telechelic oligo(propylene-ran-1-butene) could be isolated as nonvolatile oligomers from polymer residues resulting from the thermal degradation of isotactic poly(1-butene) and poly(propylene-ran-1-butene), respectively. Their structures were determined by ¹H and ¹³C NMR with attention being paid to their reactive end groups. The maximum average number of terminal vinylidene groups per molecule (f_TVD) was 1.8, indicating that about 80 mol% were α,ω-diene oligomers having two terminal vinylidene groups. This useful new telechelic oligomer had a lower polydispersity than the original polymer, in spite of its lower molecular weight and T_m. The composition of end groups of nonvolatile oligomers obtained by thermal degradation of poly(propylene-ran-1-butene) could be explained by the differences in bond dissociation energy and activation energy of elementary reactions during thermal degradation, based on the monomer composition of the original polymer.     

聚（甲基丙烯酸甲酯—二甲基二烯丙基氯化铵）的合成及表征

以水和乙醇作混合溶剂，用逐步滴加甲基丙烯酸甲酯的方法，通过自由基聚合，由溶解性和共聚活性差异较大的两种单体ＭＭＡ和二甲基二烯丙基氯化铵合成了新型含阳离子共聚物聚，并用ＩＲ和＾１Ｈ－ＮＭＲ进行了分析表征。该共聚物溶于丙酮和水组成的二元溶剂，并与Ｐ（ＭＭＡ－ＭＡＡ）有较强的分子复合能力。     

Thermal degradation of poly(p-phenylene-graft-?-caprolactone) copolymer

The thermal degradation of poly(p-phenylene-graft-?-caprolactone) (PPP), synthesized by Suzuki polycondensation of poly(?-caprolactone) (PCL) with a central 2,5-dibromo-1,4-benzene on the chain with 1,4-phenylene-diboronic acid, has been studied via direct pyrolysis mass spectrometry. The thermal degradation occurred mainly in two steps. In the first step, decomposition of PCL chains occurred. A slight increase in thermal stability of PCL chains was noted. In the second stage of pyrolysis, the decomposition of the polyphenylene backbone takes place. The evolution of CL monomer or small CL segments left on the phenyl ring continued also in the temperature region where degradation of PPP backbone started.