Crystallization behaviors and morphology of biodegradable poly(3-hydroxybutyrate-co-4-hydroxybutyrate)

Crystallization behaviors and spherulitic morphology of poly(3-hydroxybutyrate-co-4-hydroxybutyrate) [P(3HB-co-4HB)] with different 4-hydroxybutyrate (4HB) molar fraction were investigated by differential scanning calorimetry and polarized optical microscopy. Crystallization behaviors of P(3HB-co-4HB) are significantly affected by 4HB molar fraction. The melting temperature (T _m), glass transition temperature (T _g), and crystallinity (X _c) decrease with the increase of 4HB molar fraction. Banded spherulites are observed in poly (3-hydroxybutyrate) (PHB) and P(3HB-co-4HB) copolymers. The band spacing decreases with the increase of 4HB molar fraction. The morphology and growth rate of the spherulites strongly depend on 4HB molar fraction and the crystallization temperatures. The introduction of 4HB unit can inhibit the emergence of cracks in PHB spherulites.     

Radiolytic stabilization of poly(hydroxybutyrate)

Stabilization against gamma irradiation effects on Brazilian poly(hydroxybutyrate) (PHB) films was investigated by using commercial additives. With the most effective additive the G value of main chain scissions decreased from 8.6 to 1.5 scissions/100 eV in the absorbed dose range up to 35 kGy. Irradiation increased the biodegradability of the samples, whereas the additives-induced reduction in biodegradability. Irradiation treatment did not influence the degree of crystallinity. Protonic nuclear magnetic resonance (NMR-¹H) analysis revealed formation of hydroxyl-terminal groups upon irradiation.     

Effects of gamma irradiation on poly(vinyl chloride)/polystyrene blends: Investigation of radiolytic stabilization and miscibility of the mixture

Commercial polystyrene (PS) has been studied as a modifier for commercial poly(vinyl chloride) (PVC) when it was submitted to gamma irradiation. PVC/PS blends were prepared with 100/0, 95/05 and 90/10 compositions. Results for gamma-irradiated (⁶⁰Co) blends are reported and changes in viscosity-average molar mass (M_v) were analyzed. The study showed that the addition of PS into PVC decreased by 73% (95/05) and 79% (90/10) the number of scissions/100 eV in the dose range of 25-100 kGy. Viscosity analyses by the Pan et al. criterion and analyses of FT-IR spectra in the C-Cl vibration region showed negligible intermolecular interactions between the components of PVC/PS blends. However when the films of blends were irradiated to 50 kGy, certain intermolecular interactions were observed by the viscosity method. The addition of PS to PVC and the main scission effect induced by gamma irradiation decreased crosslink density of blends causing changes in the elongation of break and Young's modulus.     

Infrared Spectroscopy and X-Ray Diffraction Studies of C?H…O Hydrogen Bonding and Thermal Behavior of Biodegradable Poly(hydroxyalkanoate)

Infrared (IR) spectra and wide-angle X-ray diffraction (WAXD) patterns of poly(3-hydroxybutyrate) (PHB) and its copolyester, poly(3-hydroxybutyrate-co-3-hydroxyhexanoate), P(HB-co-HHx) (HHx = 12 mol%) were measured over a temperature range of 20 °C to higher temperatures (PHB, 185 °C, HHx = 12 mol%, 140 °C) to explore their structure change and thermal behavior and molecular interaction. The WAXD measurements revealed that the a lattice parameter increases significantly with temperature, while the b lattice parameter varies a little in the crystalline PHB and P(HB-co-HHx). It seems that the intermolecular interaction between the CO group of one helical structure and the CH₃ group of the other helical structure decreases along the a axis of crystalline PHB and P(HB-co-HHx) with temperature. The temperature-dependent IR spectral variations were analyzed for the CH stretching, CO stretching, CH₃ deformation, and C O C stretching variation regions, and bands characteristic of crystalline and amorphous parts were identified in each region. It was found from the anomalous frequencies of the CH₃ asymmetric stretching and CO stretching bands of PHB and P(HB-co-HHx) and the X-ray crystallographic structure of PHB that there is an intermolecular interaction (C H…OC hydrogen bond) between the CO group and the CH₃ group combining two helical structures in PHB and P(HB-co-HHx). In this review paper we discuss the role of the C H…OC hydrogen bonding and the crystal and lamella structure of PHB and P(HB-co-HHx) (HHx = 12 mol %) in comparison with the structure of Nylon.     

Gamma Irradiation Effects on Mechanical and Thermal Properties and Biodegradation of Poly(3-hydroxybutyrate) Based Films

Summary: Their biodegradable properties make polyhydroxyalkanoates (PHAs) ideal candidates for innovative applications. Many studies have been primarily oriented to poly(3-hydroxybutyrate) (PHB) and poly(3-hydroxybutyrate-co-3-valerate) (PHBV) and afterwards to blends of PHAs with synthetic biodegradable polymers, such as poly(ε-caprolactone) (PCL). Medical and pharmaceutical devices require sterilization and γ irradiation could provide a proper alternative since it assures storage stability and microbiological safety. This contribution presents the effect of γ irradiation on the mechanical and thermal properties and on the biodegradation of PHB, PHBV and a commercial PHB/PCL blend. Samples, prepared by compression moulding, were irradiated in air at a constant dose rate of 10 kGy/h, from 10 to 179 kGy. Polymer chain scission was assessed by changes in the molecular weight, thermal properties and tensile behaviour. The correlation between absorbed dose and changes in the mechanical properties and biodegradation is discussed in detail. The optimum dose to guarantee microbiological sterilization without damage of the structure or meaningful loss of the mechanical properties is also reported.     

Adsorption effects of poly(hydroxybutyric acid) depolymerase on chain-folding surface of polyester single crystals revealed by mutant enzyme and frictional force microscopy

Adsorption effects of poly(hydroxybutyric acid) (PHB) depolymerase from Ralstonia pickettii T1 on various polymer single crystals were studied using a catalytically inactive mutant of PHB depolymerase by means of transmission electron microscopy (TEM), atomic force microscopy (AFM), and frictional force microscopy (FFM). Six types of polymer single crystals, poly[(R)-3-hydroxybutyric acid] (P(3HB)), poly[(R)-3-hydroxybutyric acid-co-6 mol% (R)-3-hydroxyvaleric acid] (P(3HB-co-6 mol% 3HV)), poly[(R)-3-hydroxybutyric acid-co-8 mol% (R)-3-hydroxyhexanoic acid] (P(3HB-co-8 mol% 3HH)), poly(l-lactic acid) (PLLA), poly(d-lactic acid) (PDLA), and polyethylene (PE), were prepared to examine the influence of an ester bond and stereoregularity of a polymer on the enzymatic adsorption. The numbers of PHB depolymerase enzymes adsorbed on P(3HB) and P(3HB-co-6 mol% 3HV) single crystals were determined as 171 and 183 enzymes/μm² by AFM, respectively. AFM observation revealed that the concentration of PHB depolymerase enzymes adsorbed onto PLLA and PDLA single crystals is much higher compared to those on a P(3HB) single crystal, whereas the concentration of enzyme adsorbed onto PE and P(3HB-co-8 mol% 3HH) single crystals is much less. In addition, the single crystals of each polymer were characterized by TEM and FFM before and after enzymatic treatment by mutant for 1 h at 37 °C. The surface properties of P(3HB), P(3HB-co-6 mol% 3HV), and P(3HB-co-8 mol% 3HH) single crystals were changed by the enzymatic adsorption, whereas the internal structures were not affected. On the basis of these results, the properties of the binding domain of PHB depolymerase to polymer chain-folding surfaces have been discussed.     

Silver sulfide/poly(3-hydroxybutyrate) nanocomposites: Thermal stability and kinetic analysis of thermal degradation

The non-isothermal degradation of poly(3-hydroxybutyrate) (PHB) and silver sulfide/poly(3-hydroxybutyrate) (Ag₂S/PHB) nanocomposites was investigated using thermogravimetric (TG) analysis. In the composite materials, Ag₂S caused the degradation of PHB at a lower temperature as opposed to that of neat PHB. Moreover, an increase Ag₂S loading in the PHB decreased the onset temperature (T_onset) of thermal degradation, whereas it was raised upon augmenting the heating rate. From Kissinger plots, the observed trend of the degradation activation energy, E_d, was attributed to polymer-particle surface interactions and the agglomeration of Ag₂S. The thermal degradation rate constant, k, was linearly related to the Ag₂S loading in PHB. Thus, the Ag₂S nanoparticles effectively catalyzed the thermal degradation of PHB in the Ag₂S/PHB nanocomposites. Differential scanning calorimetry (DSC) data also supported the catalytic property of Ag₂S.     

Synthesis, characterization and degradability of the novel aliphatic polyester bearing pendant N-isopropylamide functional groups

The synthesis, characterization, and degradability of the novel aliphatic polyester bearing pendant N-isopropylamide functional group are reported for the first time. 2-(N-Isopropyl-2-carbamoylethyl)cyclohexanone (CCH) was first synthesized by the Michael reaction of N-isopropylacrylamide with cyclohexanone and was subsequently converted into 6-(N-isopropyl-2-carbamoylethyl)-?-caprolactone (CCL) by the Baeyer-Villiger oxidation reaction using 3-chloroperoxybenzoic acid (mCPBA) as the oxidant. Finally, the novel functionalized poly(?-caprolactone) bearing the pendant N-isopropylamide functional groups, poly(6-(N-isopropyl-2-carbamoylethyl)-?-caprolactone-co-?-caprolactone)s (poly(CCL-co-CL)), were carried out successfully by bulk ring-opening polymerization of CCL and ?-CL initiated by Sn(Oct)₂. Poly(CCL-co-CL) were characterized by ¹H NMR, ¹³C NMR, SEC and DSC. The copolymer containing 9.1 mol% CCL formed flexible films and was used to study its degradability. A phosphate buffer (pH = 7.4) with temperature 37 °C was adopted to proceed the degrading study all through. Compared with poly(?-caprolactone), the hydrolytic degradation of poly(CCL-co-CL) was much faster, which is confirmed by the weight loss and change of intrinsic viscosity.     

Synthesis and characterization of block poly(ester‐ether‐urethane)s from bacterial poly(3‐hydroxybutyrate) oligomers

Telechelic hydroxylated poly(3‐hydroxybutyrate) (PHB‐diol) oligomers have been successfully synthesized in 90–95% yield from high molar mass PHB by tin‐catalyzed alcoholysis with different diols (mainly 1,4‐butanediol) in diglyme. The PHB‐diol oligomers structure was studied by nuclear magnetic resonance, Fourier transformed infrared spectroscopy MALDI‐ToF MS, and size exclusion chromatography, whereas their crystalline structures, thermal properties and thermal stability were analyzed by wide angle X‐ray scattering, DSC, and thermogravimetric analyses. The kinetic of the alcoholysis was studied and the influence of (i) the catalyst amount, (ii) the diol amount, (iii) the reaction temperature, and (iv) the diol chain length on the molar mass was discussed. The influence of the PHB‐diol molar mass on the thermal stability, the thermal properties and optical properties was investigated. Then, tin‐catalyzed poly(ester‐ether‐urethane)s (PEEU) of M_n = 15,000–20,000 g/mol were synthesized in 1,2‐dichloroethane from PHB‐diol oligomers (P_ester) with modified 4,4'‐MDI and different polyether‐diols (P_ether) (PEG‐2000, PEG‐4000, and PPG‐PEG‐PPG). The influence of the PHB‐diol chain length, the P_ether/P_ester ratio, the polyether segment nature and the PEG chain length on the thermal properties and crystalline structures of PEEUs was particularly discussed. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1949–1961     

The thermal degradation of poly(diethyl fumarate)

The kinetics and mechanism of the thermal degradation of poly(diethyl fumarate) (PDEF) were studied by thermogravimetry, as well as by analysis of the thermolysis volatiles and polymer residue. The characteristic mass loss temperatures were determined, as were the overall thermal degradation activation energies of three PDEF samples of varying molar mass. Ethylene and ethanol were present in the thermolysis volatiles at degradation temperatures below 300 °C, while diethyl fumarate was also evidenced at higher degradation temperatures. The amount of monomer increased with increasing degradation temperature. The dependence of the molar mass of the residual polymer on the degradation time and temperature was established and the number of main-chain scissions per monomer unit, s/P₀, calculated. A thermal degradation mechanism including de-esterification and random main-chain scission is proposed. The thermal degradation of PDEF was compared to the thermolysis of poly(ethyl methacrylate) (PEMA), poly(diethyl itaconate) (PDEI) and poly(ethyl acrylate) (PEA).     

Rheological Behavior of Dope Solutions of Poly(acrylonitrile‐co‐itaconic acid) in N,N‐dimethylformamide: Effect of Polymer Molar Mass

The rheological behavior of dope solutions of poly(acrylonitrile‐co‐itaconic acid) or poly(AN‐co‐IA) is important from the point of view of deriving the spinning conditions for good quality special acrylic fibers. The viscosity of the resin dope is dictated by the polymer concentration, molar mass, temperature and shear force. The dynamic shear rheology of concentrated poly(AN‐co‐IA) polymer dope solutions in N, N‐dimethylformamide, in the molar mass (M¯_v) range of 1×10⁵ to 1×10⁶ g/mol, was investigated in the shear rate (γ′) range of 1×10¹ to 5×10⁴ min^?1. An empirical relation between η and M¯_v was found to exist at constant shear rate. The dope viscosity was dependent on the molar mass and the shear rate at a given temperature (T) and concentration. The polymer molar mass index of dope viscosity (m) was calculated as functions of concentration (c), shear rate and temperature. The m values increased with shear rate and temperature. A master equation relating m, with shear rate and temperature was derived for a given dope concentration. At higher shear rates, m tends to the value of 3.4, which is close to the molar mass index of viscosity reported for molten thermoplastics. m increased significantly with shear rate and nominally with temperature, while an increase in concentration decreased it. The onset of shear thinning of the dope shifted to a lower shear rate regime with an increase in polymer concentration and the molar mass. For a given value of molar mass, the increase in viscosity of the dope solution with polymer concentration was dependent on the shear rate.     

Multiple melting behaviour of poly(3-hydroxybutyrate-co-hydroxyvalerate) using step-scan DSC

Melting behaviour and crystal morphology of poly(3-hydroxybutyrate) (PHB) and its copolymer of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) with various hydroxyvalerate (HV) contents [5 wt.% (PHB5V), 8 wt.% (PHB8V) and 12 wt.% (PHB12V)] have been investigated by conventional DSC, step-scan differential scanning calorimetry (SDSC), wide angle X-ray diffraction (WAXRD) and hot stage polarised optical microscopy (HSPOM). Crystallisation behaviour of PHB and its copolymers were investigated by isothermal crystallisation kinetics. Thermal properties were investigated after isothermal crystallisation treatment. Multiple melting peak behaviour was observed for all polymers. SDSC data revealed that PHB and its copolymers undergo melting-recrystallisation-remelting during heating, as evidenced by exothermic peaks in the IsoK baseline (C_p,IsoK, non-reversing signal). An increase in degree of crystallinity due to significant melt-recrystallisation was observed for isothermally crystallised polymers. SDSC proved a convenient and precise method for measurement of the apparent thermodynamic specific heat (C_p,ATD, reversing signal). PHB and PHBV showed different crystal morphologies for similar crystallisation condition. HSPOM results showed that the crystallisation rates reduced and sizes of spherulites were significantly increased as HV content increased.     

Quantum yield for poly(methyl methacrylate) chain scission by 214–229 nm wavelength light

The quantum yield for poly(methyl methacrylate)chain scission by ultraviolet light in the 214–229 nm wavelength region was found to be ?_d = 0.03 scissions per absorbed photon. Samples were 1.65-μm films spun cast on silicon wafers and irradiated under flowing nitrogen by a cadmium vapor lamp. Gel permeation chromatography was used for molecular weight determination. Heating (postbaking) the irradiated films at 150°C for one hour under reduced-pressure flowing nitrogen increased the observed scissions per absorbed photon to 0.04. Glass transition temperatures by DSC are well-represented by T_g (K) = 393.3 ? 2.0 × 10⁵/M_n for the postbaked samples (139,000 > M_n > 6500).     

The influence of soft segment length on the properties of poly(butylene terephthalate-co-succinate)-b-poly(ethylene glycol) segmented random copolymers

Three series of poly(butylene terephthalate-co-succinate)-b-poly(ethylene glycol) segmented random copolymers with starting PEG number-average molecular weight (M_n(PEG)) at 600, 1000 and 2000, respectively, as well as hard segment poly(butylene succinate) (PBS) molar fraction (M_PBS) increasing from 10% to 30% were synthesized through a transesterification/polycondensation process and characterized by means of GPC, NMR, DSC, WAXD and mechanical testing etc. The investigations were mainly focused on the influence of M_n(PEG) on the properties of resulting copolymers bearing two sorts of hard segments. It is revealed that all the samples show a relatively symmetrical GPC curves with the number-average molecular weight more than 4 × 10⁴, while the polydispersity decreases from 1.9 to 1.4 as the increasing M_n(PEG) because of the prolonged time for polycondensation and the faster exclusion of small molecules by-product with the decreased molten viscosity. The sequence distribution analysis shows that the average sequence length of hard segment PBT decreases while that of PBS increases with the increasing M_PBS and are independent of the soft segment length. The approximate unit degree of randomness as well as the soft segment length turns out that the segments take a statistically random distribution along the backbone. Micro-phase separation structure is verified for the appearance of two glass transition temperatures and two melting points, respectively, in DSC thermograms of most samples. The depression of melting points and the reduction of crystallinity of hard segments with increasing M_PBS are related to the crystal lattice transition from α-PBT to PBS and discussed in the viewpoint of cohensive energy. Mechanical testing results demonstrate that the increase of amorphous domains the increase of M_PBS as well as M_n(PEG) will provide high elongation and good flexibility of copolymer chain. The in vitro degradation experiments show that the partial substitution of aromatic segment PBT with aliphatic PBS will substantially accelerate the degradation rate with enhanced safety of degradation by-products and while changing M_n(PEG) broaden the spectrum to tailor the properties.     

Infrared Spectroscopy and X-Ray Diffraction Studies on the Structure and Thermal Behavior of Biodegradable Polyhydroxyalkanoates

The structure and thermal behavior of new types of bacterial copolyester, poly(3-hydroxybutyrate-co-3-hydroxyhexanoate); P(HB-co-HHx) (HHx=2.5, 3.4, and 12 mol %) have been explored by means of wide-angle x-ray diffraction (WAXD), differential scanning calorimetry (DSC), and infrared (IR) spectroscopy. The WAXD pattern of P(HB-co-HHx) (HHx=12 mol %) copolymer measured at room temperature has revealed that it has an orthorhombic system (α=β=γ=90°) with a=5.76Å, b=13.20Å, c=5.96Å (fiber repeat), which is identical to that of poly(3-hydroxybutyrate) (PHB). It has been found from the temperature-dependent variations of the WAXD pattern that only the a lattice parameter shows the thermal expansion, while the b lattice parameter changes little with temperature in the crystalline P(HB-co-HHx) (HHx=12 mol %). This observation suggests that there are inter and intramolecular interactions between C=O groups and alkyl groups along the a axis and that interactions are broken little by little with temperature. IR spectra were measured for the four kinds of polymers over a temperature range from 30°C to high temperatures (200°C; PHB, 180°C; P(HB-co-HHx) (HHx=2.5 mol %), 180°C; P(HB-co-HHx) (HHx=3.4 mol %), 150°C; P(HB-co-HHx) (HHx=12 mol %)). Temperature-dependent IR spectral variations were analyzed for the CH, C=O, and C-O-C stretching band regions, and bands characteristic of crystalline and amorphous parts were identified in each region. It has been found from the IR study that the strength of interaction between the C=O group and the CH₃ (or CH₂) group is similar among the four polymers and that the population of C=O groups that are not involved in the interaction becomes higher with the increase in HHx. Both WAXD and IR studies have revealed that the crystallinity of P(HB-co-HHx) (HHx=12 mol %) decreases gradually starting from relatively low temperature (about 60°C) while that of PHB remains high up to 170°C.     

Production of Polyhydroxyalkanoates (PHAs) by Vibrio alginolyticus Strains Isolated from Salt Fields

Vibrio alginolyticus is a halophilic organism usually found in marine environments. It has attracted attention as an opportunistic pathogen of aquatic animals and humans, but there are very few reports on polyhydroxyalkanoate (PHA) production using V. alginolyticus as the host. In this study, two V. alginolyticus strains, LHF01 and LHF02, isolated from water samples collected from salt fields were found to produce poly(3-hydroxybutyrate) (PHB) from a variety of sugars and organic acids. Glycerol was the best carbon source and yielded the highest PHB titer in both strains. Further optimization of the NaCl concentration and culture temperature improved the PHB titer from 1.87 to 5.08 g/L in V. alginolyticus LHF01. In addition, the use of propionate as a secondary carbon source resulted in the production of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV). V. alginolyticus LHF01 may be a promising host for PHA production using cheap waste glycerol from biodiesel refining.     

Novel 3D printed shape-memory PLLA-TMC/GA-TMC scaffolds for bone tissue engineering with the improved mechanical properties and degradability

The biodegradable substitution materials for bone tissue engineering have been a research hotspot. As is known to all, the biodegradability, biocompatibility, mechanical properties and plasticity of the substitution materials are the important indicators for the application of implantation materials. In this article, we reported a novel binary substitution material by blending the poly(lactic-acid)-co-(trimethylene-carbonate) and poly(glycolic-acid)-co-(trimethylene-carbonate), which are both biodegradable polymers with the same segment of flexible trimethylene-carbonate in order to accelerate the degradation rate of poly(lactic-acid)-co-(trimethylene carbonate) substrate and improve its mechanical properties. Besides, we further fabricate the porous poly(lactic-acid)-co-(trimethylene-carbonate)/poly(glycolic-acid)-co-(trimethylene-carbonate) scaffolds with uniform microstructure by the 3D extrusion printing technology in a mild printing condition. The physicochemical properties of the poly(lactic-acid)-co-(trimethylene-carbonate)/poly(glycolic-acid)-co-(trimethylene-carbonate) and the 3D printing scaffolds were investigated by universal tensile dynamometer, fourier transform infrared reflection (FTIR), scanning electron microscope (SEM) and differential scanning calorimeter (DSC). Meanwhile, the degradability of the PLLA-TMC/GA-TMC was performed in vitro degradation assays. Compared with PLLA-TMC group, PLLA-TMC/GA-TMC groups maintained the decreasing T_g, higher degradation rate and initial mechanical performance. Furthermore, the PLLA-TMC/GA-TMC 3D printing scaffolds provided shape-memory ability at 37 ℃. In summary, the PLLA-TMC/GA-TMC can be regarded as an alternative substitution material for bone tissue engineering.     

Thermal degradation of γ-irradiated poly(vinyl chloride)

The thermal degradation of unstabilized poly(vinyl chloride) irradiated with γ-rays has been investigated by dynamic thermogravimetry in a nitrogen atmosphere. The overall effect of irradiation is to render PVC more susceptible to thermal degradation. The change in activation energy of degradation with dose showed a behavior parallel with the change of intrinsic viscosity with dose. The minimum and maximum E_a values were found to correspond with the minimum and maximum observed on [η] versus dose curves. This behavior indicates an inverse relationship between the rate of thermal degradation and molecular size.     

Synthesis, characterization and degradability of the comb-type poly(4-hydroxyl-ε-caprolactone-co-ε-caprolactone)-g-poly(l-lactide)

The novel comb-type biodegradable graft copolymers based on ε-caprolactone and l-lactide were synthesized. Firstly, 2-oxepane-1,5-dione (OPD) was synthesized by the Baeyer-Villiger oxidation of 1,4-cyclohexanedione, and was subsequently copolymerized with ε-caprolactone (CL) to produce poly(2-oxepane-1,5-dione-co-ε-caprolactone) (POCL) catalyzed by stannous(II) 2-ethylhexanoate in toluene. Then, POCL was converted into poly(4-hydroxyl-ε-caprolactone-co-ε-caprolactone) (PHCL) using sodium borohydride as reductant. Finally, poly(4-hydroxyl-ε-caprolactone-co-ε-caprolactone)-g-poly(l-lactide) (PHCL-g-PLLA) were prepared successfully by bulk ring-opening polymerization of l-lactide using PHCL as a macro-initiator. All the copolymers have been characterized by ¹H and ¹³C NMR, DSC, and GPC. Compared with the random copolymer of poly(CL-co-LA), the elongation is highly increased. And the thermal analysis showed that the crystallization rate of the PCL backbone in the graft copolymers was greatly reduced compared to the PCL homopolymer. The hydrolytic degradation of the copolymer was much faster in a phosphate buffer (pH = 7.4) at 37 °C, which is confirmed by the weight loss and change of intrinsic viscosity.     

Using Triethylborane to Manipulate Reactivity Ratios in Epoxide-Anhydride Copolymerization: Application to the Synthesis of Polyethers with Degradable Ester Functions

The anionic ring-opening copolymerization (ROCOP) of epoxides, namely of ethylene oxide (EO), with anhydrides (AH) generally produces strictly alternating copolymers. With triethylborane (TEB)-assisted ROCOP of EO with AH, statistical copolymers of high molar mass including ether and ester units could be obtained. In the presence of TEB, the reactivity ratio of EO (r_EO), which is normally equal to 0 in its absence, could be progressively raised to values lower than 1 or higher than 1. Conditions were even found to obtain r_EO equal or close to 1. Samples of P(EO-co-ester) with minimal compositional drift could be synthesized; upon basic degradation of their ester linkages, these samples afforded poly(ethylene oxide) (PEO) diol samples of narrow molar mass distribution. In other cases where r_EO were lower or higher than 1, the PEO diol samples eventually isolated after degradation exhibited a broader distribution of molar masses because of the compositional drift of initial P(EO-co-ester) samples.