Glycolysis of poly(ethylene terephthalate) (PET) using basic ionic liquids as catalysts

The glycolysis of poly(ethylene terephthalate) (PET) was studied using several ionic liquids and basic ionic liquids as catalysts. The basic ionic liquid, 1-butyl-3-methylimidazolium hydroxyl ([Bmim]OH), exhibits higher catalytic activity for the glycolysis of PET, compared with 1-butyl-3-methylimidazolium bicarbonate ([Bmim]HCO₃), 1-butyl-3-methylimidazolium chloride ([Bmim]Cl) and 1-butyl-3-methylimidazolium bromide ([Bmim]Br). FT-IR, ¹H NMR and DSC were used to confirm the main product of glycolysis was bis(2-hydroxyethyl) terephthalate (BHET) monomer. The influences of experimental parameters, such as the amount of catalyst, glycolysis time, reaction temperature, and dosages of ethylene glycol on the conversion of PET, yield of BHET were investigated. The results showed a strong influence of the mixture evolution of temperature and reaction time on depolymerization of PET. Under the optimum conditions of m(PET):m(EG): 1:10, dosage of [Bmim]OH at 0.1 g (5 wt%), reaction temperature 190 °C and time 2 h, the conversion of PET and the yield of BHET were 100% and 71.2% respectively. Balance between the polymerization of BHET and depolymerization of PET could be changed when the reaction time was more than 2 h and contents of catalyst and EG were changed.     

Electron-beam irradiation on poly(propylene carbonate) in the presence of polyfunctional monomers

Poly(propylene carbonate) (PPC) showed predominantly degradation under electron-beam irradiation, accompanied by deterioration of its mechanical performance due to sharp decrease of the molecular weight. Crosslinked PPC was prepared by addition of polyfunctional monomer (PFM) to enhance the mechanical performance of PPC. When 8 wt% of PFM like triallyl isocyanurate (TAIC) was added, crosslinked PPC with a gel fraction of 60.7% was prepared at 50 kGy irradiation dose, which showed a tensile strength at 20 °C of 45.5 MPa, whereas it was only 38.5 MPa for pure PPC. The onset degradation temperature (T_i) and glass transition temperature (T_g) of this crosslinked PPC was 246 °C and 45 °C, respectively, a significant increase related to pure PPC of 211 °C and 36 °C. Therefore, thermal and mechanical performances of PPC could be improved via electron-beam irradiation in the presence of suitable PFM.     

Synthesis of isotactic star-shaped poly(vinyl alcohol)

Isotactic 6-armed star-shaped poly(vinyl alcohol) (PVA) with a narrow molecular weight distribution was successfully prepared by the living cationic polymerization of 6-armed star-shaped poly(tert-butyl vinyl ether) (PTBVE) and subsequent acidic ether cleavage. The PTBVE was synthesized using hexa(chloromethyl) melamine (HCMM) as a hexafunctional initiator and ZnI₂ or ZnCl₂ as an activator in toluene/MC (1/1 v/v) at −70 °C. A better living stability of PTBVE was obtained in the ZnCl₂ activator system. The number average molecular weight and the polydispersity index of the 6-armed star-shaped PTBVE polymerized with ZnCl₂ at −70 °C for 24 h were 156,000 g/mol and 1.47, respectively. The fraction of the mm sequence of the resulting PVA was 52%.     

Thermal analysis of the melting process of poly(trimethylene terephthalate) using FTIR micro-spectroscopy

Thermal spectra of poly(trimethylene terephthalate) (PTT) were collected over a temperature range of 40-250 °C by FTIR micro-spectroscopy. Based on the changes of absorbance ratio corresponding to characteristic groups in low and high vibration energy states, the apparent enthalpy differences of vibration energy states transformation (ΔH_v) in the melting process have been calculated by van’t Hoff equation at constant pressure. In comparison with the values of ΔH_v, the status of participation for the vibration mode of various characteristic groups in PTT macromolecular chain segments was analyzed. It was found that the vibration modes related to the trimethylene glycol unit (O-CH₂-CH₂-CH₂-O) of PTT behaved significant sensitivity and made prominent contribution in the melting process. By the summarization of corresponding data, it has shown that the melting course concerned amorphous phase began at as early as 218 °C, accompanied by the occurrence of crystallization to certain extent, and the ending point was at approximately 238 °C; whereas the melting course concerned crystalline phase began till 228 °C, with the top value of 238 °C, and ended at 242 °C. Besides, for the particular ordered arrangement of chain segments of aromatic polyesters in the melting course, FTIR analysis has provided a reasonable explanation on a molecular level.     

Rubber toughening of poly(ether imide) by modification with poly(butylene terephthalate)

Rubber toughening of poly(ether imide) (PEI) has been elusive up to now due to the high processing temperature of PEI, which leads to degradation of the rubber. In this study, by profiting from the miscibility between PEI and poly(butylene terephthalate) (PBT), and the low T_g of PBT, we prepared a blend by melt extrusion with 20 wt% PBT in an attempt to render it toughenable by decreasing its T_g and processing temperature. The PEI-rich blend was subsequently mixed with maleic anhydride (0.9 wt%) grafted poly(ethylene-octene) copolymer (mPEO) up to 30 wt%. The decrease in T_g and processing temperature resulted in no observable degradation of the mPEO, and to the formation of a homogeneous morphology of rubber particles with a fine particle size, indicating that compatibilization was achieved. Upon rubber addition, stiffness decreased, while a very large toughness increase occurred with only 15% mPEO (impact strength more than 10-fold that of the PEI-PBT matrix). Upon observation of the fracture surface, the increase in impact strength was attributed partially to the cavitation and debonding of the rubber particles, and mostly to the deformation and yielding of the PEI-PBT matrix.     

Thermal stability of microencapsulated epoxy resins with poly(urea-formaldehyde)

A series of microcapsules filled with epoxy resins with poly(urea-formaldehyde) (PUF) shell were synthesized by in situ polymerization, and they were heat-treated for 2 h at 100 °C, 120 °C, 140 °C, 160 °C, 180 °C and 200 °C. The effects of surface morphology, wall shell thickness and diameter on the thermal stability of microcapsules were investigated. The chemical structure and surface morphology of microcapsules were investigated using Fourier-transform infrared spectroscope (FTIR) and scanning electron microscope (SEM), respectively. The thermal properties of microcapsules were investigated by thermogravimetric analysis (TGA and DTA) and by differential scanning calorimetry (DSC). The thermal damage mechanisms of microcapsules at lower temperature (<251 °C) are the diffusion of the core material out of the wall shell or the breakage of the wall shell owing to the mismatch of the thermal expansion of core and shell materials of microcapsules. The thermal damage mechanisms of microcapsules at higher temperature (>251 °C) are the decomposition of shell material and core materials. Increasing the wall shell thickness and surface compactness can enhance significantly the weight loss temperatures (T_d) of microcapsules. The microcapsules with mean wall shell thickness of 30 ± 5 μm and smoother surface exhibit higher thermal stability and can maintain quite intact up to approximately 180 °C.     

Thermal degradation mechanism of poly(ethylene succinate) and poly(butylene succinate): Comparative study

Two aliphatic polyesters that consisted from succinic acid, ethylene glycol and butylene glycol, —poly(ethylene succinate) (PESu) and poly(butylene succinate) (PBSu)—, were prepared by melt polycondensation process in a glass batch reactor. These polyesters were characterized by DSC, ¹H NMR and molecular weight distribution. Their number average molecular weight is almost identical in both polyesters, close to 7000 g/mol, as well as their carboxyl end groups (80 eq/10⁶ g). From TG and Differential TG (DTG) thermograms it was found that the decomposition step appears at a temperature 399 °C for PBSu and 413 °C for PESu. This is an indication that PESu is more stable than PBSu and that chemical structure plays an important role in the thermal decomposition process. In both polyesters degradation takes place in two stages, the first that corresponds to a very small mass loss, and the second at elevated temperatures being the main degradation stage. The two stages are attributed to different decomposition mechanisms as is verified from the values of activation energy determined with iso-conversional methods of Ozawa, Flyn, Wall and Friedman. The first mechanism that takes place at low temperatures, is auto-catalysis with activation energy E = 128 and E = 182 kJ/mol and reaction order n = 0.75 and 1.84 for PBSu and PESu, respectively. The second mechanism is nth-order reaction with E = 189 and 256 kJ/mol and reaction order n = 0.68 and 0.96 for PBSu and PESu, respectively, as they were calculated from the fitting of experimental results.     

New heat stable and processable poly(amide-ether-imide)s derived from 5-(4-trimellitimidophenoxy)-1-trimellitimido naphthalene and various diamines

New aromatic diimide-dicarboxylic acid having flexible ether linkage, 5-(4-trimellitimidophenoxy)-1-trimellitimido naphthalene, was synthesized by the reaction of trimellitic anhydride with 5-(4-aminophenoxy)-1-naphthylamine. Then, a series of novel aromatic poly(amide-ether-imide)s were prepared by the phosphorylation polycondensation of the synthesized monomer with various aromatic diamines. A model compound was synthesized by the reaction of the monomer with aniline. The resulting polymers with inherent viscosities of 0.43-0.70 dl/g were obtained in high yield. All new compounds including the naphthalene-based monomer, model compound, and the resulted polymers were characterized by FT-IR and NMR spectroscopic methods. The ultraviolet λ_max values of the poly(amide-ether-imide)s were also determined. The resulted polymers exhibited a good solubility in a variety of high polar solvents such as N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), N-methyl-2-pyrrolidone (NMP), and pyridine. For some of the polymers obtained the crystallinity behavior was estimated by means of wide-angle X-ray diffraction (WXRD) method, and the resulted polymers exhibited nearly an amorphous nature. Thermal stability of the obtained polymers was determined by thermogravimetric analysis (TGA/DTG), and the 10% weight loss temperatures of the one-step degraded poly(amide-ether-imide)s were found to be in the range between 528 and 551 °C in nitrogen. From differential scanning calorimetric (DSC) analyses, the polymers showed T_gs between 276 and 307 °C. Cyclic voltammetry (CV) measurements of a typical polymer showed that they are also electrochemically stable.     

Synthesis and characterization of new aromatic poly(ether imide)s and their gas transport properties

A series of processable fluorinated poly(ether imide)s (PIs) were synthesized by reacting a diamine monomer, 1,4-bis-[{2′-trifluromethyl 4′-(4″-aminophenyl)phenoxy}] benzene (HQA) with six different aromatic dianhydrides e.g., BPADA, 6FDA, ODPA, BPDA, BTDA and PMDA. The polyimides showed reasonably high glass-transition temperature (T_g up to 280 °C) and high thermal stability (T_d,10 up to 558 °C). The membranes of these polymers showed tensile strength up to 107 MPa with elongation at break up to 15%, low water absorption (0.61–1.29%), low dielectric constant (2.10–3.13 at 1 MHz) and high optical transparency (λ_cut-off up to 466 nm). The PI membrane prepared from 6FDA exhibited high permeability and permselectivity for O₂/N₂ (P_O2 = 11.8 and P_O2/P_N2 = 9.44) gas pair which eventually surpassed the present upper boundary limit drawn by L.M. Robeson.     

Graft copolymerization of itaconic acid-methacrylamide comonomers onto poly(ethylene terephthalate) fibers

The graft copolymerization of itaconic acid-methacrylamide (IA-MAAm) comonomers was carried out using benzoyl peroxide as initiator onto poly(ethylene terephthalate) (PET) fibers in an aqueous medium. The grafted fibers were characterized by FTIR, TGA, DSC and SEM analysis. Effect of various parameters on graft yield such as feed composition, feed and initiator concentration, reaction time and temperature were investigated. The graft yield in the presence of MAAm increased because of the synergistic effect of MAAm comonomer. While, the graft yield alone with the IA onto PET fiber was 2.2%, the use of MAAm as a comonomer increased the amount of IA introduced to the PET fiber up to 13.7%. The reactivity ratios for both monomers were determined by using a Fineman-Ross plot. The grafting rate and saturation graft yield was increased upon increasing the temperature between 65 °C and 85 °C. When the temperature increased further than 85 °C, the saturation graft yield decreased. The graft yield has shown an increase up to an initiator concentration of 1.0 × 10⁻² M and slightly decreased. The grafting increased the dyeability with acidic and basic dyes, and moisture absorption capacity but decreased the thermal stability of the fibers.     

Synthesis and anhydrous proton conductivity of poly(5-vinyltetrazole) prepared by free radical polymerization

5-Vinyltetrazole (VT)-based polymer is mainly produced by ‘click chemistry’ from polyacrylonitrile due to the unavailability of 5-vinyltetrazole monomer, which usually produces copolymers of VT and acrylonitrile rather than pure poly(5-vinyltetrazole) (PVT). In present work, VT was synthesized from 5-(2-chloroethyl)tetrazole via dehydrochlorination. A series of PVT with different molecular weight were synthesized by normal free radical polymerization. The chemical structures of VT and PVT were characterized by ¹H NMR and FTIR. PVT without any doped acid exhibits certain proton conductivity at higher temperature and anhydrous state. The proton conductivity of PVT decreases at least 2 orders of magnitude after methylation of tetrazole. PVT and PVT/H₃PO₄ composite membranes are thermally stable up to 200 °C. The glass transition temperature (T_g) of PVT/xH₃PO₄ composite membranes is shifted from 90 °C for x = 0.5 to 55 °C for x = 1. The temperature dependence of DC conductivity for pure PVT exhibits a simple Arrhenius behavior in the temperature range of 90–160 °C, while PVT/xH₃PO₄ composite membranes with higher H₃PO₄ concentration can be fitted by Vogel–Tamman–Fulcher (VTF) equation. PVT/1.0H₃PO₄ exhibits an anhydrous proton conductivity of 3.05 × 10⁻³ at 110 °C. The transmission of the PVT/xH₃PO₄ composite membrane is above 85% in the wavelength of visible light and changes little with acid contents. Thus, PVT/xH₃PO₄ composite membranes have potential applications not only in intermediate temperature fuel cells but also in solid electrochromic device.     

Synthesis, photoluminescent and electrochromic properties of new aromatic poly(amine-hydrazide)s and poly(amine-1,3,4-oxadiazole)s derived from 4,4′-dicarboxy-4″-methyltriphenylamine

A series of new poly(amine-hydrazide)s I were prepared from the dicarboxylic acid 4,4′-dicarboxy-4″-methyltriphenylamine with terephthalic dihydrazide (TPH) and isophthalic dihydrazide (IPH), respectively, via the Yamazaki phosphorylation reaction. Polymers I were readily soluble in many common organic solvents, and could be solution cast into transparent, tough, and flexible films with good mechanical properties. Differential scanning calorimetry (DSC) indicated that the hydrazide polymers had T_g’s in the range of 222-223 °C and could be thermally cyclodehydrated into the corresponding oxadiazole polymers in the range of 300-400 °C. The resulting poly(amine-1,3,4-oxadiazole)s II exhibited T_g’s in the range of 269-283 °C, 10% weight-loss temperatures in excess of 511 °C, and char yield at 800 °C in nitrogen higher than 63%. These poly(amine-hydrazide)s I exhibited strong UV-Vis absorption bands at 351-355 nm in NMP solution. Their photoluminescence spectra in NMP solution and film showed maximum bands around 459-461 nm in the blue region for I series. The hole-transporting and electrochromic properties are examined by electrochemical and spectroelectrochemical methods. Cyclic voltammograms of the poly(amine-hydrazide)s I prepared by casting polymer solution onto an indium-tin oxide (ITO)-coated glass substrate exhibited one reversible oxidation redox couples at 1.32-1.33 V vs. Ag/AgCl in acetonitrile solution. All obtained poly(amine-hydrazide)s I revealed excellent stability of electrochromic characteristics, changing color from original pale yellowish to blue.     

Lyotropic liquid crystalline poly(aryl ether ketone) copolymer containing phthalazinone moiety and biphenyl mesogen

A novel lyotropic liquid crystalline material poly(aryl ether ketone) copolymer containing phthalazinone moiety and biphenyl mesogen named P-8515 was developed by a mild solution polycondensation method. The molecular weight (M_n) was 53,000 and the value of molecular weight distribution index (MDI) was 2.49 detected by GPC. The critical concentration (C^∗) of P-8515 was 36 wt% and P-8515 exhibited characteristic nematic lyotropic liquid crystalline phases in NMP solution at different concentrations and the phase morphology changed to a typical threaded texture when shear forces were induced from PLM observations. The T_g value was 238 °C and the value for 5% weight loss temperature was 515 °C in nitrogen from DSC and TGA determinations, respectively.     

Effect of small amount of poly(ethylene naphthalate) on isothermal crystallization and spherulitic morphology of poly(trimethylene terephthalate)

The effect of a small amount of poly(ethylene naphthalate) (PEN) in its blends with poly(trimethylene terephthalate) (PTT) on isothermal melt-crystallization kinetics and spherulitic morphology of the blends was thoroughly investigated. The maximum PEN content in the blends was 9 wt%. Due to the single composition-dependent glass transition temperature (T_g) that was observed for each blend, these blends appeared to be miscible in the amorphous state. After isothermal crystallization from the melt state, the neat PTT and its blends with PEN exhibited either double or triple melting endotherms. The triple endothermic peaks were observed in both the neat PTT and the blends when being crystallized at crystallization temperatures (T_c) of less than or equal to 195 °C. The equilibrium melting temperature () for the neat PTT was determined based on the linear Hoffman–Weeks extrapolative method to be 248 °C. Such values for the blends were found to decrease with the addition and increasing amount of PEN. Both the neat PTT and the blends were isothermally crystallized over the T_c range of 190–205 °C. At a given T_c, the 97PTT/3PEN blend exhibited a half-time of crystallization (t_0.5) value that was lower, while it exhibited reciprocal half-time (), Avrami rate constant (K_A), and spherulitic growth rate (G) values that were greater, than those of the neat PTT. With further increase in the PEN content, the t_0.5 value increased, while the , K_A, and G values decreased. Analysis of the G values based on the Lauritzen–Hoffman's (LH) secondary nucleation theory showed that the neat PTT and the 91PTT/9PEN blend exhibited a regime II→III transition at 194 °C (467.2 K), while no regime transition was observed for the other two blends. The lateral and the fold surface free energies (σ and σ_e) and the work of chain folding (q) for the neat PTT and the blends were 19.4, 30.2–46.3 erg cm⁻², and 2.4–3.6 kcal mol⁻¹, respectively. Lastly, the effect of both the T_c and the PEN content on morphology and texture of the PTT spherulites was also investigated and the results showed that the texture of the spherulites became coarser with increasing T_c and PEN content.     

Synthesis and properties of phthalonitrile-terminated oligomeric poly(ether imide)s containing phthalazinone moiety

Three novel series of soluble and curable phthalonitrile-terminated oligomeric poly(ether imide)s containing phthalazinone moiety were synthesized from an excess amount of three dianhydrides and phthalazinone-based diamine, followed by reacting with 4-(3-aminophenoxy)phthalonitrile (APPh) in a two-step, one-pot reaction, respectively. The phthalonitrile oligomers containing phthalazinone moiety were cured in the presence of 4,4′-diaminodiphenylsulfone (DDS). The oligomers and the crosslinked polymers were characterized by DSC, FT-IR and elemental analysis. These phthalonitrile oligomers containing phthalazinone groups were found to be soluble in some aprotic solvents, such as chloroform, pyridine, m-cresol and N-methyl-2-pyrrolidone (NMP). The crosslinked polymers were insoluble in all solvents. The thermal properties of the oligomers and the crosslinked polymers were evaluated using DSC and TGA analysis. The phthalonitrile oligomers showed high glass transition temperatures (T_gs) in the range of 214-256 °C and high decomposition temperatures with 10% weight loss (T_d10%) ranging from 523 to 553 °C. The crosslinked polymers showed excellent thermal stability with the 10% weight loss temperatures ranging from 543 to 595 °C, but did not exhibit a glass transition temperature upon heating to 350 °C.     

Facile fabrication of a novel high performance CO2 separation membrane: Immobilization of poly(amidoamine) dendrimers in poly(ethylene glycol) networks

Poly(amidoamine) (PAMAM) dendrimers showed high CO₂ separation properties and were successfully immobilized in a poly(ethylene glycol) (PEG) network upon photopolymerization of PEG dimethacrylate. The PAMAM dendrimer incorporation ratio was readily controlled, and a stable self-standing membrane containing up to 75 wt.% PAMAM dendrimer was obtained. The CO₂ separation properties over smaller H₂ were investigated by changing the PAMAM dendrimer content or generation and CO₂ partial pressure (ΔPCO₂$\mathrm{\Delta }{P}_{\text{C}{\text{O}}_2}$) under atmospheric conditions. Especially, a polymeric membrane containing 50 wt.% PAMAM dendrimer (0th generation) exhibited an excellent CO₂/H₂ selectivity of 500 with CO₂ permeability of 2.74 × 10⁻¹⁴ m³(STP)m/(m² s Pa) or 3.65 × 10³ barrer (1 barrer = 7.5 × 10⁻¹⁸ m³(STP)m/(m² s Pa)) when a mixture gas (CO₂/H₂: 5/95 by vol.) was fed at 25 °C and 100 kPa with 80% relative humidity. This polymeric materials are promising for a novel CO₂ separation membrane.     

Preparation of poly(vinyl pivalate) microspheres by dispersion polymerization in an ionic liquid and saponification for the preparation of poly(vinyl alcohol) with high syndiotacticity

We report here a successful free-radical dispersion polymerization of vinyl pivalate (VPi) in an ionic liquid, 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([bmim][TFSI]) using poly(vinyl pyrrolidone) (PVP) as a stabilizer. Morphological analysis by FE-SEM revealed that poly(vinyl pivalate) (PVPi) obtained from dispersion polymerizations were in the form of spherical particles. Micron-sized, PVPi particles with a number-average molecular weight (M_n) of 166,400 g/mol could be obtained using 5% stabilizer (w/w to monomer) at 65 °C for 20 h. The effects of varying concentration of stabilizer, initiator and monomer upon polymer yield, molecular weight, and morphology of PVPi were also investigated. Analogous polymerizations in dimethyl sulfoxide (DMSO) and bulk served as references. In addition, the preparation of poly(vinyl alcohol) (PVA) by saponification of the resultant PVPi was described.     

Synthesis and properties of novel aromatic poly(ester-imide)s bearing 1,5-bis(benzoyloxy)naphthalene units

Two series of new aromatic poly(ester-imide)s were prepared from 1,5-bis(4-aminobenzoyloxy)naphthalene (p-1) and 1,5-bis(3-aminobenzoyloxy)naphthalene (m-1), respectively, with six commercially available aromatic tetracarboxylic dianhydrides via a conventional two-stage synthesis that included ring-opening polyaddition to give poly(amic acid)s followed by chemical imidization to polyimides. The intermediate poly(amic acid)s obtained in the first stage had inherent viscosities of 0.41-0.84 and 0.66-1.37 dl/g, respectively. All the para-series and most of the meta-series poly(ester-imide)s were semicrystalline and showed less solubility. Two of the meta-series poly(ester-imide)s derived from less rigid dianhydrides were amorphous and readily soluble in polar aprotic solvents, and they could be solution-cast into transparent and tough films with good mechanical properties. The meta-series polymers derived from rigid dianhydrides were generally semicrystalline and showed less solubility. Except for one example, the meta-series poly(ester-imide)s displayed discernible T_gs in the range 239-273 °C by DSC. All of these two series poly(ester-imide)s did not show significant decomposition below 450 °C in nitrogen or in air.     

Effect of nanoscale fully vulcanized acrylic rubber powders on crystallization of poly(butylene terephthalate): Isothermal crystallization

Poly(butylene terephthalate) (PBT) was blended with nanoscale fully vulcanized acrylic rubber (FVAR) powders in a twin extruder, and the FVAR powders were dispersed well in PBT from scanning electron microscopy (SEM) and transmission electron microscope (TEM) investigation. The isothermal crystallization kinetics of PBT/FVAR blends were investigated by differential scanning calorimeter (DSC) and simulated by Avrami model. Equilibrium melting temperature was estimated by the nonlinear Hoffman-Weeks relation. The active energy (ΔE) and nucleation parameters (K_g) increased with the addition of FVAR, suggesting that FVAR particles hindered the crystallization; however more content FVAR had a lower ΔE and K_g because FVAR powders acted as heterogeneous nuclei in the nucleation of crystallization and facilitated the crystallization of PBT. The crystallization ability followed the order: PBT > PBT/FVAR6 > PBT/FVAR3 > PBT/FVAR1 when undercooling was considered.     

Thermal degradation kinetics of the biodegradable aliphatic polyester, poly(propylene succinate)

The preparation of the biodegradable aliphatic polyester poly(propylene succinate) (PPSu) using 1,3-propanediol and succinic acid is presented. Its synthesis was performed by two-stage melt polycondensation in a glass batch reactor. The polyester was characterized by gel permeation chromatography, ¹H NMR spectroscopy and differential scanning calorimetry (DSC). It has a number average molecular weight 6880 g/mol, peak temperature of melting at 44 °C for heating rate 20 °C/min and glass transition temperature at −36 °C. After melt quenching it can be made completely amorphous due to its low crystallization rate. According to thermogravimetric measurements, PPSu shows a very high thermal stability as its major decomposition rate is at 404 °C (heating rate 10 °C/min). This is very high compared with aliphatic polyesters and can be compared to the decomposition temperature of aromatic polyesters. TG and Differential TG (DTG) thermograms revealed that PPSu degradation takes place in two stages, the first being at low temperatures that corresponds to a very small mass loss of about 7%, the second at elevated temperatures being the main degradation stage. Both stages are attributed to different decomposition mechanisms as is verified from activation energy determined with isoconversional methods of Ozawa, Flyn, Wall and Friedman. The first mechanism that takes place at low temperatures is auto-catalysis with activation energy E = 157 kJ/mol while the second mechanism is a first-order reaction with E = 221 kJ/mol, as calculated by the fitting of experimental measurements.