Poly(vinyl chloride)/clay nanocomposites: X-ray diffraction, thermal and rheological behaviour

The paper concentrates on poly(vinyl chloride) - PVC - from the point of view of structural characterisation of PVC/clay nanocomposites through X-ray diffraction, thermogravimetric analysis and dynamic rheometric analysis. PVC plasticizer was mixed with clay, natural and organophilic, and the suspension was then compounded with other components. Two factors were followed: effect of shearing alone, and in combination with temperature. The type of filler and the method of composite preparation affect the mechanical and thermal properties of the composite, through delamination and exfoliation levels. The results showed that the thermal degradation is shifted towards higher temperatures for organophilic clays, compared to chemically untreated natural clay.     

Thermal stability, smoke emission and mechanical properties of poly(vinyl chloride)/hydrotalcite nanocomposites

Poly(vinyl chloride)/hydrotalcite (PVC/HT) nanocomposites were prepared through vinyl chloride suspension polymerization in the presence of HT nanoparticles surface modified with alkyl phosphate (AP). The thermal stability, smoke emission and mechanical properties of PVC/HT nanocomposites were investigated. It was found that AP molecules were effectively absorbed by HT particles with no intercalation into the interlayer of HT. The dispersion morphologies of PVC/HT nanocomposites were observed by transmission electron microscopy showing that the majority of HT particles were dispersed in the PVC matrix in the nanoscale. The Congo Red measurement and thermogravimetric analysis showed that the thermal stability time, and the temperatures at 10% weight loss and at the maximum weight loss rate of PVC resins increased as the weight fraction of HT in the composite resins increased. The well-dispersed nano-sized HT showed an obvious smoke suppression effect on PVC. The maximum smoke density decreased about 1/3 and 1/2 when 2.5 wt% and 5.3 wt% nano-sized HT were incorporated into PVC, respectively. Furthermore, PVC/HT nanocomposites exhibited greater tensile strength and impact strength than the pristine PVC.     

离子交联聚氯乙烯的结构与性能

由氯乙烯/丙烯酸悬浮共聚合成了不同羧基含量的PVC树脂,采用溶液反应和熔融加工法制备离子交联PVC,对其结构和性能进行了研究.结果表明,共聚物中羧基主要以二聚体形式存在,用金属离子中和能形成部分络合结构;用Ca²⁺、Mg²⁺离子络合的羧基含量较高的VC/AA共聚物存在离子对聚集态结构;离子对含量、金属离子种类和增塑剂浓度影响离子聚集相的比例和稳定性,离子聚集具有热可逆性;离子交联使PVC的T_g、熔体粘度和回弹性提高.     

PVB存在下PVC化学法脱氯化氢的研究

ＰＶＢ存在下ＰＶＣ化学法脱氯化氢的研究刘恒＊李大成陈朝珍（四川联合大学化工学院成都６１００６５）关键词聚氯乙烯，脱氯化氢，聚乙烯醇缩丁醛１９９６－０９－０８收稿，１９９７－０５－２６修回国家教育委员会留学归国人员资助费资助课题近年来在ＰＶＣ脱氯化氢制...     

Poly(vinyl alcohol)/GO-MMT nanocomposites: Preparation,structure and properties

A facile, efficient and environment friendly method is established to prepare poly(vinyl alcohol)(PVA) based graphene oxide-montmorillonite(GO-MMT) nanocomposites in aqueous media. GO-MMT nanohybrid is obtained by the combination of GO and MMT in water without any reducing or stabilizing agents. The formation of GO-MMT nanohybrid is due to the hydrogen bonding and crosslinking effects. The sodium ions within MMT sheets act as crosslinkers between GO sheets and MMT platelets. The resultant nanocomposites are characterized by means of X-ray diffraction(XRD), scanning electron microscopy(SEM), differential scanning calorimetry(DSC), thermogravimetric analysis(TGA) and mechanical testing. Compared to that of pure PVA, PVA nanocomposites show enhanced thermal stabilities and mechanical properties, which results from strong interfacial adhesion of the nanoadditives in PVA matrix. The further increase in the tensile strength and modulus results from strong interaction between PVA chains and layered GO-MMT as well as good mechanical properties of GO-MMT hybrid, compared to PVA/GO and PVA/MMT nanocompsoites.     

Properties of poly(vinyl chloride)/wood flour/montmorillonite composites: Effects of coupling agents and layered silicate

Organomodified montmorillonite (OMMT) was prepared using cetylalkyl trimethyl amine bromide. OMMT and wood flour (WF) were surface-modified by silane coupling agent. They were melt-blended with polyvinyl chloride (PVC) and extruded into wood-plastic composite samples using one conical twin screw extruder. The effects of their contents on the composite mechanical properties were investigated. X-ray diffraction, transmission electron microscopy and scanning electron microscopy observed intercalation and dispersion of the OMMT. FTIR and X-ray photoelectron spectroscopy were used to analyze the silane-modification effects. The possible reaction mechanisms were proposed. After wood flour was modified by 1.5 phr silane, the impact strength and the tensile strength of wood flour-PVC composite were increased by 14.8% and 18.5%, respectively. Mechanical tests showed that the addition of OMMT did not enhance the untreated wood flour-PVC composites. However, adding 0.5% OMMT did improve the mechanical properties of the treated ones. The grafting improved the interfacial compatibility between components producing higher properties of the composites. Further addition of OMMT reinforced the composites. Too higher contents of silane and OMMT impaired some properties because of weak interfacial layer and higher concentrated stress. Cone calorimetry showed that the fire flame retardancy and smoke suppression of composites were strongly improved with the addition of OMMT.     

聚氯乙烯薄膜的压电性研究

系统地研究了极化条件、热历程、增塑作用等与聚氯乙烯薄膜压电性的关系,并且讨论了聚氯乙烯薄膜压电性对时间的稳定性。研究结果表明,极化聚氯乙烯薄膜的压电应变常数d_(33)值为2.1×10~(-12)C/N,压电电压常数g_(33)达到73.9×10~(-3)V·m/N,与经典的压电材料石英晶体的压电性相当。     

化学交联聚氯乙烯树脂的合成和结构

研究了氯乙烯/交联单体悬浮共聚时,交联单体种类、浓度和聚合温度对化学交联聚氯乙烯树脂结构的影响.对于氯乙烯/邻苯二甲酸二烯丙基酯(VC/DAP)悬浮共聚体系,凝胶含量和凝胶交联密度随DAP起始浓度的增加而增大;DAP浓度相同时,凝胶含量和凝胶交联密度随聚合温度上升而下降;当凝胶含量较高时,分子链物理缠结对凝胶交联密度有较大贡献,凝胶交联密度随凝胶含量增加而快速上升.在相同交联单体浓度下,氯乙烯/马来酸二烯丙基酯(VC/DAM)共聚物的凝胶含量最大,VC/DAP共聚物次之,氯乙烯/乙二醇二甲基丙烯酸酯(VC/EGDMA)共聚物最小,这是由于DAM单体的竞聚率小于1,且含有马来酸双键,EGDMA单体的竞聚率远大于1.     

The thermal degradation behaviour of polydimethylsiloxane/montmorillonite nanocomposites

A series of novel polydimethylsiloxane/montmorillonite (PDMS/MMT) nanocomposites was prepared. The thermal degradation behaviour of these nanocomposites was studied by means of Thermal Volatilization Analysis (TVA) and Thermogravimetric Analysis (TGA). The major degradation products were identified as cyclic oligomeric siloxanes from D₃ to D_7, and higher oligomeric siloxane residues. Other minor degradation products include methane, bis-pentamethylcyclotrisiloxane, propene, propanal, benzene and dimethylsilanone. The results demonstrate that the nanoclay significantly alters the degradation behaviour of the PDMS network, modifying the profile of the thermal degradation and reducing the overall rate of volatiles evolution. The results also indicate that the nanoclay promotes the formation of dimethylsilanone and benzene by inducing low levels of radical chain scission.     

Development of a Poly(vinyl chloride)-based Nitrate Ion-selective Electrode

The authors developed a nitrate ion-selective electrode(ISE) based on poly(vinyl chloride)(PVC) membrane with methyltrioctylammonium nitrate as a carrier and 1-decanol as a plasticizer. The performance of the nitrate-sensitive membranes was optimized by tuning the composition of components. The electrode exhibits a linear response with a Nernstian slope of (52±1.0) mV per decade for the nitrate ion concentration ranging from 5.8×10^-5 mol/L to 1.0 mol/L. The electrode can be used to detect a low concentration of nitrate ions down to 3×10^-5 mol/L in a pH range of 2.1-11.5 without any compensation. The advantage of the electrode includes simple preparation, short response time and good repeatability. The detection performance of the novel electrode on nitrate ions has been tested for water samples.     

不同接枝度的十八硫醇化聚氯乙烯梳状聚合物的结构和性能

通过亲核取代反应,制备了一系列不同接枝率的十八硫醇(C_(18)H_(37)SH)接枝改性聚氯乙烯(PVC)(记作PVCS18).通过傅立叶变换红外光谱(FTIR)、核磁共振氢谱(1H-NMR)、示差扫描量热仪(DSC)、热重分析(TG)和X射线衍射(XRD)对PVCS18的结构、相变行为、热稳定性和热能行为进行了研究.结果表明,随十八硫醇钠(C_(18)H_(37)SNa)投料的增加,PVCS18接枝率增加,最高达到50.2%.PVCS18相转变的出现,主要是接枝的十八烷基链段贡献的.随接枝率由8.5%增加到50.2%,相转变温度由61.7℃升高到66.3℃,热焓值由5.3 k J/mol提高到50.9 k J/mol,结晶碳原子数从1.4增加到13.8.主侧链间连接键的极性和基团大小明显影响侧链烷基的结晶能力及可结晶碳原子数目.PVCS18的热稳定性较PVC的没有明显热损失行为出现,该材料可在较高的温度下加工使用.     

聚氯乙烯-丙烯酸丁酯接枝共聚物的结构表征

以通用聚氯乙烯(PVC)和脱氯化氢PVC树脂为基体,采用悬浮溶胀接枝共聚法合成聚氯乙烯-丙烯酸丁酯接枝共聚物,对脱氯化氢PVC和接枝共聚物的结构进行了表征.结果表明,以碱液为介质加热PVC能脱除少量氯化氢,得到以链节数为2,3,4的共轭双键为主的不饱和结构,而树脂的分子量变化不大;在相同接枝反应条件下,采用脱氯化氢PVC与丙烯酸丁酯接枝共聚可以提高接枝率和接枝效率;PVC接枝共聚物的特性粘度随接枝率增加而增加,其重均分子量和分子量分布指数均大于接枝所用的PVC树脂.     

聚氯乙烯/层状双氢氧化物纳米复合材料研究进展

聚氯乙烯(PVC)/层状双氢氧化物(LDHs)纳米复合材料相比于纯聚氯乙烯具有更好的热稳定性、力学性能、阻燃抑烟性、耐候性与耐光性等,是一种性能优异并具有广泛应用前景的新型聚合物基纳米复合材料。本文首先介绍了LDHs的化学组成和结构特点,并对其制备过程和性质特点进行了分析和探讨;然后综述了PVC/LDH纳米复合材料的制备、结构表征及性能等方面的最新研究进展,重点阐述了LDHs的表面有机化处理及其对PVC/LDH纳米复合材料制备与性能的重要作用;最后对其应用前景进行展望。     

Poly(epsilon-caprolactone)/clay nanocomposites via “click” chemistry

Poly(epsilon-caprolactone)/clay nanocomposites were prepared by copper(I) catalyzed azide/alkyne cycloaddition (CuAAC) “click” reaction. In this method, ring-opening polymerization of epsilon-caprolactone using propargyl alcohol as the initiator has been performed to produce alkyne-functionalized PCL and the obtained polymers were subsequently attached to azide-modified clay layers by a CuAAC “click” reaction. The exfoliated polymer/clay nanocomposites were characterized by X-ray diffraction spectroscopy, thermogravimetric analysis and transmission electron microscopy.     

Application of high resolution thermogravimetry to the study of thermal stability of poly(vinyl chloride) resins

The influence of microstructure on thermal degradation behaviour was studied in five samples of pure poly(vinyl chloride) (PVC) obtained at different polymerisation temperatures. Tacticity of the samples was characterized by Fourier transform infrared spectroscopy (FTIR), and their thermogravimetric behaviour was measured by high resolution (Hi-Res™) TGA. This technique is able to detect two independent weight loss steps in the dehydrochlorination. The relative contribution of these two steps responds to different syndiotacticity tendency of PVC samples, in accordance with FTIR results.     

Radiation effects on the thermal degradation of poly(vinyl chloride) and poly(vinyl alcohol)

Radiation effects on the formation of conjugated double bonds in the thermal degradation of poly(vinyl chloride) (PVC) and poly(vinyl alcohol) (PVA) were investigated. Thin films of PVC and PVA were either irradiated with γ-rays at ambient temperature (pre-irradiation) and then subjected to thermal treatment, or irradiated at elevated temperatures (in situ irradiation). An extensive enhancement of the thermal degradation was observed for the pre-irradiation of the PVC films, which was more effective than the effect of the in situ irradiation at the same absorption dose. For the PVA degradation, however, the effect of the in situ irradiation was larger than that of the pre-irradiation. The results were explained and related mechanisms were discussed based on radiation-induced chemical reactions and their individual contributions to the thermal degradation behaviors of the two polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3089–3095, 1998     

Synthesis and characterization of functionalized carbon black/poly(vinyl alcohol) high refractive index nanocomposites

Carbon black(CB)/polymer composites with high refractive index(RI) were fabricated from poly(vinyl alcohol) (PVA) and covalently functionalized nano-CB(PVA-es-CB) by simple esterification reaction.Transmission electron microscopy showed that uniform aggregates of PVA-es-CB nanoparticles with a size smaller than 100 nm formed in the nanocomposite films.EUipsometric measurements indicated that the PVA-es-CB/PVA composite films had a RI in the range 1.520-1.598 linearly increased with the PVA-es-CB volume content.Theoretical equation based on Lorentz-Lorenz theory provided reasonably close estimation of the refractive indices to the experimentally observed values.The hybrid films also revealed relatively good surface planarity,thermal stability and optical transparency.     

Poly(N,N-dimethylaminoethyl methacrylate) grafted poly(vinyl chloride)s synthesized via ATRP process and their membranes for dye separation

To functionalize poly(vinyl chloride)(PVC) for various applications, monomers containing tertiary amine group are incorporated into PVC via atom transfer radical polymerization(ATRP) initiated by the labile chlorines in their backbones. The kinetics of synthesis was carefully investigated, and it is proven that the grafting polymerization process can be effectively controlled by regulating the reaction time. The membranes are fabricated using PVC and copolymers by non-solvent induced phase separation(NIPS) process. The hydrophilicity and pore structure of copolymer membranes were enhanced as well, these membranes are endowed with positive charge. When PDMA%(i.e., the PDMA weight percentage in copolymer) is 31.1%, the flux and Victoria blue B rejection are 26.0 L?m?2?h?1(0.5 MPa) and 91.2%, respectively. Thus, the newly synthesized polymer is proven to be a promising material for dye separation with positive charges.     

改性聚氯乙烯絮凝剂的合成及其性能的研究

采用乙醇胺为亲核试剂对聚氯乙烯进行改性,控制胺化反应条件可以得到不同氮含量的产物.确定了最佳反应条件：温度80℃,PVC结构单元与乙醇胺的摩尔比1/1,反应时间小于36h,反应压力2.8MPa;用红外光谱表征了产物的结构、用元素分析测定了产物中N、H、C、Cl的含量;以ω=0.03的硅藻土水悬浮液模拟污水,考察了产物的絮凝性能.