A method for estimating wall friction in turbulent wall-bounded flows

We describe a simple method for estimating turbulent boundary layer wall friction using the fit of measured velocity data to a boundary layer model profile that extends the logarithmic profile all the way to the wall. Two models for the boundary layer profile are examined, the power-series interpolation scheme of Spalding and the Musker profile which is based on the eddy viscosity concept. The performance of the method is quantified using recent experimental data in zero pressure gradient flat-plate turbulent boundary layers, and favorable pressure gradient turbulent boundary layers in a pipe, for which independent measurements of wall shear are also available. Between the two model profiles tested, the Musker profile performs much better than the Spalding profile. Results show that the new procedure can provide highly accurate estimates of wall shear with a mean error of about 0.5% in friction velocity, or 1% in shear stress, an accuracy that is comparable to that from independent direct measurements of wall shear stress. An important advantage of the method is its ability to provide accurate estimates of wall shear not only based on many data points in a velocity profile but also very sparse data points in the velocity profile, including only a single data point such as that originating from a near-wall probe.     

FLOW STRUCTURE IN THE TURBULENT BOUNDARY LAYER OVER DIRECTIONAL RIBLETS SURFACES

本文采用时间解析的二维粒子图像测速技术,对零压力梯度光滑以及汇聚和发散沟槽表面平板湍流边界层统计特性和流动结构进行了研究.结果表明在垂直于汇聚和发散沟槽表面的对称平面内,相对于光滑壁面,发散沟槽壁面使当地边界层厚度、壁面摩擦阻力、湍流脉动、雷诺应力等明显减小;而汇聚沟槽壁面对湍流边界层特性和流动结构的影响正好相反,汇聚沟槽使壁面流体有远离壁面向上运动的趋势,因而导致边界层厚度增加了约43%;同时,在汇聚沟槽表面情况下流向大尺度相干结构更容易形成,这对减阻是不利的.此外,顺向涡数量在湍流边界层的对数区均存在一个极大值,发散沟槽表面所对应的极大值位置更靠近沟槽壁面,而在汇聚沟槽表面则有远离壁面的趋势,由顺向涡诱导产生的较强的喷射和扫掠运动会在湍流边界层中产生较强的剪切作用,顺向涡数量的减少是发散沟槽壁面当地摩擦阻力降低的主要原因.     

Numerical prediction of turbulent boundary layer noise from a sharp-edged flat plate

An efficient hybrid uncorrelated wall plane waves–boundary element method (UWPW-BEM) technique is proposed to predict the flow-induced noise from a structure in low Mach number turbulent flow. Reynolds-averaged Navier-Stokes equations are used to estimate the turbulent boundary layer parameters such as convective velocity, boundary layer thickness, and wall shear stress over the surface of the structure. The spectrum of the wall pressure fluctuations is evaluated from the turbulent boundary layer parameters and by using semi-empirical models from literature. The wall pressure field underneath the turbulent boundary layer is synthesized by realizations of uncorrelated wall plane waves (UWPW). An acoustic BEM solver is then employed to compute the acoustic pressure scattered by the structure from the synthesized wall pressure field. Finally, the acoustic response of the structure in turbulent flow is obtained as an ensemble average of the acoustic pressures due to all realizations of uncorrelated plane waves. To demonstrate the hybrid UWPW-BEM approach, the self-noise generated by a flat plate in turbulent flow with Reynolds number based on chord Re_c = 4.9 × 10⁵ is predicted. The results are compared with those obtained from a large eddy simulation (LES)-BEM technique as well as with experimental data from literature.     

Passively controlled supersonic cavity flow using a spanwise cylinder

An experimental investigation of a passively controlled open cavity with a length to depth ratio of six and freestream Mach number of 1.4 was conducted to investigate the mechanisms responsible for the observed surface pressure reductions. The passive control comes from placing a spanwise aligned cylinder in the boundary layer near the leading edge of the cavity. The two control configurations were isolated from previous experiments of the fluctuating surface pressure and correspond to a larger diameter rod near the top of the boundary layer and a smaller diameter rod placed near the wall. These were further analyzed using particle image velocimetry in an attempt to elicit the responsible mechanism for the flow control. The use of two-point statistics revealed the wall normal turbulent velocity correlation’s evolution became elongated in the wall normal direction. This suggests that the shear layer may be less-organized and consists of smaller-scale structures. The disturbance of the feedback receptivity loop is clearly demonstrated for the controlled configurations evidenced by weakened correlation signals between the aft wall sensor and positions on the cavity floor. The presence of the rod is shown to decrease the mean shear gradient, more effectively for the large rod placed at the top of the boundary layer, throughout the shear layer. The efficacy of the control leads to an initially thicker shear layer which spreads more rapidly and is clearly demonstrated by vorticity growth rates, mean, and turbulent flowfield statistics.     

Self-preservation of rough-wall turbulent boundary layers

It is proposed that all fully rough-wall boundary layers should satisfy self-preservation more closely than a smooth-wall boundary layer. Previous work has shown that the self-preserving forms of the momentum and turbulent kinetic energy equations for a zero pressure gradient turbulent boundary layer, at sufficiently high Reynolds number, require that the wall shear stress is constant with x, and the layer thickness increases linearly with x. Measurements in two rough wall boundary layers suggest these conditions are met without assuming a form for the mean velocity distribution, and are more likely to exist in a fully rough wall layer than a smooth wall layer.     

Wall temperature effects on shock unsteadiness in a reattaching compressible turbulent shear layer

In this study, the effect of heat transfer on the compressible turbulent shear layer and shockwave interaction in a scramjet has been investigated. To this end, highly resolved Large Eddy Simulations (LES) are performed to explore the effect of wall thermal conditions on the behavior of a reattaching free shear layer interacting with an oblique shock in compressible turbulent flows. Various wall-to-recovery temperature ratios are considered, and results are compared to the adiabatic wall. It is found that the wall temperature affects the reattachment location and the shock behavior in the interaction region. Furthermore, fluctuating heat flux exhibits a strong intermittent behavior with severe heat transfer compared to the mean, characterized by scattered spots. The distribution of the Stanton number shows a strong heat transfer and complex pattern within the interaction, with the maximum thermal (heat transfer rates) and dynamic loads (root-mean-square wall pressure) found for the case of the cold wall. The analysis of LES data reveals that the thermal boundary condition can significantly impact the wall pressure fluctuations level. The primary mechanism for changes in the flow unsteadiness due to the wall thermal condition is linked to the reattaching shear layer, which agrees with the compressible turbulent boundary layer theory.     

An experimental study of two flows through an axisymmetric sudden expansion

Two turbulent separated and reattaching flows produced by a sudden expansion in a pipe have been studied. The first was produced by a simple axisymmetric sudden enlargement from a nozzle of diameter 80 mm to a pipe of diameter 150 mm. The second was the flow at the same enlargement with the addition of a centerbody 90 mm downstream of the nozzle exit. Detailed measurements of velocity and skin friction (made primarily using pulsed wires) and of wall static pressure are presented. Without the centerbody the flow structure is similar to that observed in other sudden pipe expansions and over backward-facing steps. A turbulent free shear layer, bearing some similarity to that of a round jet, grows from separation and then reattaches to the pipe wall downstream. Reattachment is a comparatively gradual process, the shear layer approaching the wall at a glancing angle. The introduction of the centerbody causes the shear layer to curve towards the wall and reattach at a much steeper angle. Reattachment is much more rapid; gradients of skin friction and pressure along the wall are many times those without the centerbody. The high curvature of the shear layer strongly influences its turbulent structure, locally suppressing turbulence levels and reducing its growth rate.     

Reynolds Stress Budgets in Couette and Boundary Layer Flows

Reynolds stress budgets for both Couette and boundary layer flows are evaluated and presented. Data are taken from direct numerical simulations of rotating and non-rotating plane turbulent Couette flow and turbulent boundary layer with and without adverse pressure gradient. Comparison of the total shear stress for the two types of flows suggests that the Couette case may be regarded as the high Reynolds number limit for the boundary layer flow close to the wall. The limit values of turbulence statistics close to the wall for the boundary layer for increasing Reynolds number approach the corresponding Couette flow values. The direction of rotation is chosen so that it has a stabilizing effect, whereas the adverse pressure gradient is destabilizing. The pressure-strain rate tensor in the Couette flow case is presented for a split into slow, rapid and Stokes terms. Most of the influence from rotation is located to the region close to the wall, and both the slow and rapid parts are affected. The anisotropy for the boundary layer decreases for higher Reynolds number, reflecting the larger separation of scales, and becomes close to that for Couette flow. The adverse pressure gradient has a strong weakening effect on the anisotropy. All of the data presented here are available on the web [36]. This revised version was published online in July 2006 with corrections to the Cover Date.     

Investigation of the heat transfer mechanism in supersonic turbulent boundary layers

A method is described for calculating turbulent Prandtl numbers from Mach number and total temperature profiles in supersonic boundary layers. The calculations are based on boundary layer measurements in the Mach number range from 3.5 to 5. The investigations clearly indicate that in addition to accurate profile measurements reliable values of shear stress and heat flux at the wall must exist, in order to be able to calculate the turbulent Prandtl number in the viscous regime of the boundary layer. For flow conditions with and without heat transfer, the derived turbulent Prandtl numbers indicate that the turbulent transport of heat decreases much faster towards the wall than the turbulent transport of momentum. The results of the analysis show that only the unequivocal qualitative result of increasing turbulent Prandtl numbers in the viscous region of the boundary layer, can be expected. The variation of the turbulent Prandtl number can be described successfully using a simple approximation, based on the mixing length concept, and is applied to the calculation of total temperature distribution using the law of the wall for compressible flow.     

Mechanism of compressor airfoil boundary layer flow control using nanosecond plasma actuation

The flow control effects of nanosecond plasma actuation on the boundary layer flow of a typical compressor controlled diffusion airfoil are investigated using large eddy simulation method. Three types of plasma actuation are designed to control the boundary layer flow, and two mechanisms of compressor airfoil boundary layer flow control using nanosecond plasma actuation have been found. The plasma actuations located within the laminar boundary layer flow can induce a small vortex structure through influencing on the density and pressure of the flow field. As the small vortex structure moves downstream along the blade surface with the main flow, it can suppress the turbulent flow mixing and reduce the total pressure loss. The flow control effect of the small vortex structure is summarized as wall jet effect. Differently, the plasma actuation located within the turbulent boundary layer flow can act on the shear layer flow and induce a large vortex structure. While moving downstream, this large vortex structure can suppress the turbulent flow mixing too.     

Wall pressure fluctuations due to mean-shear-turbulence interaction in a turbulent boundary layer

The cross-correlated power spectrum of wall pressure fluctuations and the derivative of the turbulent velocity component normal to the wall is measured at a longitudinal coordinate; this spectrum, along with the mean shear, determines the contribution of the mean-shear-turbulence interaction to pressure fluctuations at a wall under a turbulent boundary layer. The spectrum is used to calculate the power spectrum and the transverse cross-correlated power spectrum of pressure fluctuations at the wall. Comparison of calculated and directly measured pressure spectra indicates that wall pressure fluctuations are almost completely determined by the mean-shear-turbulence interaction.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 4, pp. 28–34, July–August, 1976.The author thanks G. P. Morozov-Rostovskii and Yu. A. Konokhov for fabricating a miniature hot-wire anemometer and help in carrying out the experiment.     

A hybrid numerical approach to predict the vibrational responses of panels excited by a turbulent boundary layer

In this work, a hybrid numerical approach to predict the vibrational responses of planar structures excited by a turbulent boundary layer is presented. The approach combines an uncorrelated wall plane wave technique with the finite element method. The wall pressure field induced by a turbulent boundary layer is obtained as a set of uncorrelated wall pressure plane waves. The amplitude of these plane waves are determined from the cross spectrum density function of the wall pressure field given either by empirical models from literature or from experimental data. The response of the planar structure subject to a turbulent boundary layer excitation is then obtained from an ensemble average of the different realizations. The numerical technique is computationally efficient as it rapidly converges using a small number of realizations. To demonstrate the method, the vibrational responses of two panels with simply supported or clamped boundary conditions and excited by a turbulent flow are considered. In the case study comprising a plate with simply supported boundary conditions, an analytical solution is employed for verification of the method. For both cases studies, numerical results from the hybrid approach are compared with experimental data measured in two different anechoic wind tunnels.     

Effect of a moving wall on a fully developed, equilibrium turbulent boundary layer

Experiments were conducted in a wind tunnel to assess the effect of a moving wall on a fully developed, equilibrium turbulent boundary layer. Pitot-static and total head probes were used in conjunction with both single- and two-component hot-wire anemometer probes to quantify the effect of wall motion on the boundary layer velocity statistics. A variable speed, seamless belt formed the wind tunnel test section wall. When stationary, the belt was found to possess a fully developed, equilibrium turbulent boundary layer in excellent agreement with archival data. With the tunnel wall moving at the free-stream speed, and at a sufficient distance above the wall, the velocity statistics in the moving-wall boundary layer were found to collapse well when scaled as a self-preserving turbulent wake. The near-wall mean velocity profile of the moving wall was found to exhibit an extended region of linearity compared to canonical turbulent boundary layer and internal flows. This can be attributed to the reduced shear resulting from wall motion and the subsequent reduction in Reynolds stress. Received: 2 June 1999/Accepted: 8 August 2000     

Wall shear stress measurement in a turbulent pipe flow using ultrasound Doppler velocimetry

A turbulent boundary layer of a water flow is investigated by means of pulsed ultrasound Doppler velocimetry. The advantage of this method is the acquisition of complete velocity profiles along the sound propagation line within very short time intervals. The shear stress velocity, used for normalizing the velocity profiles, was determined by fitting the profiles to the universal profiles in a turbulent boundary layer obtained from Prandtl's mixing length theory. A coordinate transformation in the near-wall region is proposed to allocate the velocity data to "true" wall distances. From the experimental values of the wall shear stress velocity, the friction factors for a turbulent pipe flow are calculated and compared to the Blasius law. The overall error in measurement was estimated to NJ.4%.     

An experimental-based model for prediction of flow noise with drag reducing polymers

The drag reduction characteristics of certain high molecular weight polymers have been studied by various investigators. Because of the polymer’s ability to reduce turbulent shear stress and dependence of the boundary layer wall pressure spectral amplitude on the shear stress, polymer has the potential to suppress noise and vibration caused by the boundary layer unsteady pressures. Compared to its effect on drag reduction, polymer additive effects on turbulent boundary layer (TBL) wall pressure fluctuations have received little attention. Kadykov and Lyamshev [Sov. Phys. Acoust. 16 (1970) 59], Greshilor et al. [Sov. Phys. Acoust. 21 (1975) 247] showed that drag reducing polymer additives do indeed reduce wall pressure fluctuations, but they have not established any scaling relationship which effectively collapse data. Some effort has been made by Timothy et al. [JASA 108 (1) (2000) 71] at Penn State University to develop a scaling relationship for TBL wall pressure fluctuations that are modified by adding drag reducing polymer to pure water flow. This paper presents a theoretical model based on the work of the Timothy et al. team at ARL, Penn State University. Through this model one can estimate, reduction in TBL flow induced noise and vibration for rigid smooth surfaces due to release of drag reducing polymers in boundary layer region. Using this theoretical model, flow noise as experienced by a typical flush mounted hydrophone has been estimated for a smooth wall plate as a function of polymer additive concentration. Effect of non-dimensionalisation of the wall pressure fluctuations frequency spectra with traditional outer, inner and mixed flow variables will also be addressed in the paper. The paper also covers a model based on molecular relaxation time in polymer additives which not only reduce drag but also flow induced noise up to certain polymer concentration.     

Near-wall damping in model predictions of separated flows

Different near-wall scalings are reviewed by the use of data from direct numerical simulations (DNS) of attached and separated adverse pressure gradient turbulent boundary layers. The turbulent boundary layer equation is analysed in order to extend the validity of existing wall damping functions to turbulent boundary layers under severe adverse pressure gradients. A proposed near-wall scaling is based on local quantities and the wall distance, which makes it applicable for general computational fluid dynamics (CFD) methods. It was found to have a similar behaviour as the pressure-gradient corrected analytical y^* scaling and avoids the inconsistencies present in the y⁺ scaling. The performance of the model is illustrated by model computations using explicit algebraic Reynolds stress models with near-wall damping based on different scalings.     

Study of turbulent boundary layers on smooth and rough surfaces with arbitrary pressure gradients

The results of an experimental investigation into the steady-state plane turbulent boundary layer in an incompressible liquid at an impermeable wall are presented. Cases of flow at smooth and rough surfaces in the presence of a longitudinal pressure gradient are considered. The results of measurements of the turbulent structure of the flow at various distances from the channel inlet are presented. A detailed analysis of the kinematic and dynamic characteristics of the flow is given. Special attention is paid to the boundary region of the flow close to the wall. A universal law is proposed for the variation in the local resistance coefficient along the boundary layer.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 3, pp. 126–134, May–June, 1971.     

TRPIV investigation of space-time correlation in turbulent flows over flat and wavy walls

The present experimental work is devoted to in- vestigate a new space-time correlation model for the turbulent boundary layer over a flat and a wavy walls. A turbulent boundary layer flow at Reo = 2460 is measured by tomographic time-resolved particle image velocimetry （Tomo-TRPIV）. The space-time correlations of instantaneous streamwise fluctuation velocity are calculated at 3 different wall-normal locations in logarithmic layer. It is found that the scales of coherent structure increase with moving far away from the wall. The growth of scales is a manifestation of the growth of prevalent coherent structures in the turbulent boundary layer like hairpin vortex or hairpin packets when they lift up. The resulting contours of the space-time correlation exhibit elliptic-like shapes rather than straight lines. It is suggested that, instead of Taylor hypothesis, the elliptic model of the space-time correlation is valid for the wallbounded turbulent flow over either a flat wall or a wavy wall. The elliptic iso-correlation curves have a uniform preferred orientation whose slope is determined by the convection velocity. The convection velocity derived from the space-time correlation represents the velocity at which the large-scale eddies carry small-scale eddies. The sweep velocity rep- resents the distortions of the small-scale eddies and is intimately associated with the fluctuation velocity in the logarithmic layer of turbulent boundary layers. The nondimensionalized correlation curves confirm that the elliptic model is more proper for approximating the space-time correlation than Taylor hypothesis, because the latter can not embody the small-scale motions which have non-negligible distortions. A second flow over a wavy wall is also recorded using TRPIV. Due to the combined effect of shear layers and the adverse pressure gradient, the space-time correlation does not show an elliptic-like shape at some specific heights over the wavy wall, but in the outer region of the wavy wallbounded flow, the elliptic model remai     

Turbulent separated reattached flow in a two-dimensional curved-wall diffuser

A turbulent separation-reattachment flow in a two-dimensional asymmetrical curved-wall diffuser is studied by a two-dimensional laser doppler velocimeter. The turbulent boundary layer separates on the lower curved wall under strong pressure gradient and then reattaches on a parallel channel. At the inlet of the diffuser, Reynolds number based on the diffuser height is 1.2×10⁵ and the velocity is 25.2m/s. The results of experiments are presented and analyzed in new defined streamline-aligned coordinates. The experiment shows that after Transitory Detachment Reynolds shear stress is negative in the near-wall backflow region. Their characteristics are approximately the same as in simple turbulent shear layers near the maximum Reynolds shear stress. A scale is formed using the maximum Reynolds shear stresses. It is found that a Reynolds shear stress similarity exists from separation to reattachment and the Schofield-Perry velocity law exists in the forward shear flow. Both profiles are used in the experimental work that leads to the design of a new eddy-viscosity model. The length scale is taken from that developed by Schofield and Perry. The composite velocity scale is formed by the maximum Reynolds shear stress and the Schofield-Perry velocity scale as well as the edge velocity of the boundary layer. The results of these experiments are presented in this paper.     

Temporal development of turbulent boundary layers with embedded streamwise vortices

The interaction of streamwise vortices with turbulent boundary layer has been investigated using large-eddy simulation. The initial conditions are a pair of counterrotating Oseen vortices with flow between them directed toward the wall (common-flow-down), superimposed on various instantaneous realizations of a turbulent boundary layer. The time development of the vortices and their interaction with the boundary layer are studied by integrating the filtered Navier-Stokes equations in time. The most important effects of the vortices on the boundary layer are the thinning of the boundary layer between vortices (downwash region) and the thickening of the boundary layer in the upwash region. The vortices first move toward the wall as a result of the self-induced velocity, and then apart from each other because of the image vortices due to the solid wall. The Reynolds stress profiles highlight the highly three-dimensional structure of the turbulent boundary layer modified by the vortices. The presence of significant turbulent activity near the vortex center and in the upwash region suggests that localized instability mechanisms in addition to the convection of turbulent energy by the secondary flow are responsible for this effect. High levels of turbulent kinetic energy and secondary stresses in the vicinity of the vortex center are also observed. The numerical results show good agreement with experimental results.This work was supported by the Office of Naval Research under Grant N00014-89-J-1638. Computer time was supplied by the San Diego Supercomputing Center.