Emergence of chaos during dendritic growth of ice

A transition from deterministic to chaotic growth behavior along the dendrite axis has been experimentally found and investigated. A “correlation structure” of a growing dendrite has been revealed in terms of relationship between oscillations of the dendrite tip velocity and the branching dynamics at different distances from the tip. It is shown that the dendritic growth of ice in supercooled water is an example of nonequilibrium morphogenesis of a dissipative system demonstrating deterministic chaos.     

相场法模拟多元合金过冷熔体中的枝晶生长

在二元合金相场模型研究的基础上，进行扩展获得了多元合金相场模型.以Al-Si-Mg三元合金为例，采用该相场模型实现了逼真地模拟多元合金凝固过程的等轴枝晶生长，得到了二次或更高次晶臂生长等复杂的枝晶形貌.随着第三组元Mg含量的减少，枝晶的二次枝晶越发达，枝晶中溶质的偏析越严重，枝晶尖端的生长速率和半径越大，与丁二腈-丙酮体系中枝晶尖端生长速率、半径随溶质浓度变化关系的理论计算和实验结果相符合.另外，枝晶初生晶臂中心的溶质浓度最低，在被二次晶臂包围的界面区域的溶质浓度最高；固液界面区域具有较大的浓度梯度，其中枝晶尖端前沿的梯度最大. 关键词： 相场法 多元合金 凝固过程 枝晶生长     

界面能各向异性对定向凝固枝晶生长的影响

采用元胞自动机 (cellular automaton, CA) 模型研究了界面能各向异性对二维定向凝固枝晶生长的影响. 模拟结果显示当晶体的择优生长方向与热流方向一致时, 随着界面能各向异性强度的增大, 凝固组织形态由弱界面能各向异性时的海藻晶转变为强界面能各向异性时的树枝晶. 同时, 界面能各向异性强度会影响稳态枝晶尖端状态的选择, 界面能各向异性越强, 定向凝固稳态枝晶尖端半径越小, 尖端界面前沿的液相浓度和过冷度越小. 稳态枝晶生长的尖端状态选择参数与界面能各向异性强度也存在标度律的指数关系, 而枝晶一次间距则受界面能各向异性强度影响较弱. 当晶体的择优生长方向与热流方向呈-40°夹角时随着界面能各向异性强度的增大, 凝固组织形态由海藻晶逐渐转变为退化枝晶, 后又逐渐转变为倾斜枝晶. 关键词： 元胞自动机 枝晶 界面能各向异性     

对流作用下枝晶形貌演化的数值模拟和实验研究

合金凝固过程中存在于枝晶尖端液相区的强制对流和自然对流均能改变溶质扩散层厚度,从而会对枝晶形貌产生较大影响.在元胞自动机模型基础上,耦合液体流动方程、热传导方程和溶质对流扩散方程,建立了新的计算微观组织演化的数值模型,并利用该模型研究了强制对流和自然对流对枝晶生长的影响.三维数值模拟结果再现了强制对流作用下等轴枝晶的生长过程,揭示了强制对流对枝晶生长速率和尖端半径的影响特点.同时利用该模型模拟了NH₄Cl-H₂O溶液定向凝固过程中自然对流对柱状晶生长的影响,并采用相应的实验进行验证.模拟结果与实验结果符合良好,从而证明该模型是可靠的,可推广到实际合金系中. 关键词： 元胞自动机 对流 4Cl-H₂O溶液')" href="#">NH₄Cl-H₂O溶液 定向凝固     

Growth mechanism of Si-faceted dendrites

The growth mechanism of Si-faceted dendrite was studied using an in situ observational technique. We directly observed the growth processes of Si-faceted dendrites from Si melts. It is found that triangular corners with an angle of 60 degrees are formed at the dendrite tip. We present an original growth model for faceted dendrites based on the experimental evidence. The model fully explains the growth process of faceted dendrites.     

相场法模拟NiCu合金非等温凝固枝晶生长

利用相场模型与溶质场、温度场进行耦合计算,以Ni-40.83%Cu合金为例模拟了二元合金枝晶生长过程.系统研究相场模型中相场和温度场耦合强度对枝晶形貌和浓度分布的影响.模拟结果表明:随着耦合强度的增加,相场受温度场的影响加大,界面前沿变得不稳,扰动被放大,主枝上出现了二次枝晶.同时,枝晶尖端的生长速率增大,而枝晶尖端的曲率半径减小,枝晶前沿的溶质富集现象也更严重;另外,计算结果与Ivantsov理论符合较好. 关键词： 相场法 NiCu合金 枝晶生长 Ivantsov理论     

Effect of gravity convection on interface morphology during solidification

An experimental apparatus consisting of a crystal growth room and a crystal growth observation system was developed for the study of the effect of the gravity convection perpendicular to the growth direction on the growth process by use of model alloy succinonitrile (SCN)-5wt%ethanol. It was found that the convection improves the stability of the interface and causes the downstream alternation of the cell growth direction because of the dual effect of the Stokes force and the gravity. The second dendrite arm facing the flow comes into being earlier than that at another side when the interface transforms cell to dendrite. Then the dendrite at the side facing the flow comes into being earlier. The second dendrite arm facing the flow grows faster and is more developed than that at another side. In addition, the primary dendrite arm spacing increases and the dendrite tip radius decreases under the gravity convection. Supported by the National Natural Science Foundation of China (Grant Nos. 50331040 and 60171043)     

相场模型模拟液固界面各向异性作用下自由枝晶生长

采用自适应有限元方法求解相场模型,分别对界面能各向异性和界面动力学各向异性条件下自由枝晶生长过程进行了模拟.计算表明两种各向异性均显著影响枝晶的生长,随着各向异性的增大枝晶尖端生长速度增大,尖端半径降低. 两种各向异性对自由枝晶生长有着不同形式的影响,在界面能各向异性条件下,枝晶生长稳定性系数与各向异性系数成幂函数关系;而在动力学各向异性条件下,稳定性系数与各向异性系数成线性关系. 关键词： 界面能各向异性 动力学各向异性 自由枝晶生长 相场模型     

Phase-field simulation of dendritic growth in a binary alloy with thermodynamics data

This paper simulates the dendrite growth process during non-isothermal solidification in the Al-Cu binary alloy by using the phase-field model. The heat transfer equation is solved simultaneously. The thermodynamic and kinetic parameters are directly obtained from existing database by using the Calculation of Phase Diagram （CALPHAD） method. The effects of the latent heat and undercooling on the dendrite growth, solute and temperature profile during the solidification of binary alloy are investigated. The results indicate that the dendrite growing morphologies could be simulated realistically by linking the phase-field method to CALPHAD. The secondary arms of solidification dendritic are better developed with the increase of undercooling. Correspondingly, the tip speed and the solute segregation in solid-liquid interface increase, but the tip radius decreases.     

过冷熔体中枝晶生长的相场模拟

本文利用相场方法对过冷镍熔体中枝晶生长过程进行了模拟,发现在过冷度低于 200 K时,生长速度与过冷度之间近似呈幂函数关系,当过冷度高于 200 K时,生长速度与过冷度之间基本呈线性关系。伴随着速度/过冷度之间关系的变化,枝晶尖端半径/过冷度的关系则呈现先减小后增加的趋势,并在 200 K时达到最小。本文还将模拟结果与实验值和经典LKT理论进行了比较,对上述关系转变的物理机制进行了分析。     

Phase-field modeling of faceted growth in solidification of alloys

A regularization of the surface tension anisotropic function used in vapor-liquid-solid nanowire growth was introduced into the quantitative phase-field model to simulate the faceted growth in solidification of alloys. Predicted results show that the value of δ can only affect the region near the tip, and the convergence with respect to δ can be achieved with the decrease of δ near the tip. It can be found that the steady growth velocity is not a monotonic function of the cusp amplitude, and the maximum value is approximately at ε=0.8 when the supersaturation is fixed. Moreover, the growth velocity is an increasing function of supersaturation with the morphological transition from facet to dendrite.     

基于MeshTV界面重构算法的二元合金自由枝晶生长元胞自动机模型

本文基于MeshTV界面重构算法, 发展了二元合金凝固自由枝晶生长的元胞自动机 (cellular automaton, CA) 模型. 通过采用MeshTV界面重构算法, 在细化的界面元胞内重构出了固液界面的位置. 在此基础上, 发展了一种同时适合描述纯物质与合金凝固界面生长的动力学模型. 与非界面重构的CA模型相比, 本文所发展的模型可以在较大的网格尺寸下实现模型的收敛, 同时网格各向异性不明显, 且能够反映界面能各向异性参数ε 对自由枝晶生长的影响. 在ε =0.02时, 通过与描述自由枝晶生长的LGK理论模型相比较, 发现计算的枝晶尖端速度与LGK理论模型的预测符合较好, 而计算的枝晶尖端半径比LGK理论预测值大于约20%.     

Velocity and shape selection of dendritic crystals in a forced flow

The phase-field method is used to simulate the two-dimensional growth of a dendritic crystal in a forced flow. The selection of the velocity and shape of the dendrite tip is investigated as a function of flow rate, growth direction relative to the flow, as well as anisotropy strength, and the results for the upstream growing tips are compared to existing theoretical predictions.     

强制对流和自然对流作用下枝晶生长的数值模拟

建立了一个基于格子玻尔兹曼方法 （LBM） 的二维模型,对强制对流和自然对流作用下合金凝固过程中的枝晶生长行为进行了模拟研究. 与传统的基于求解Navier-Stokes方程计算流场的方法不同,本模型采用基于分子动理论的LBM对凝固过程中的传输现象进行数值计算. 用三组粒子分布函数分别建立了计算流场、由对流和扩散所控制的浓度场和温度场的LBM演化方程. 通过求解LBM演化方程获得固/液界面前沿的浓度和温度分布. 然后,基于溶质平衡方法计算了枝晶生长的驱动力. 为了对模型进行验证,将模拟在强制和自然对流作用下枝晶上游尖端的稳态生长特征分别与Oseen-Ivantsov 解析解和修正的Lipton-Glicksman-Kurz 模型预测结果进行了比较, 模拟结果和理论预测结果符合良好. 模拟结果还表明,对流使热量和溶质从上游传输到下游,从而加速了枝晶在上游方向的生长,而抑制了下游方向的生长,形成了非对称的枝晶形貌. 关键词： 微观组织模拟 枝晶生长 对流 格子玻尔兹曼方法     

液相对流对定向凝固胞/枝晶间距的影响

采用类金属透明模型合金丁二腈-1.8 wt%丙酮(SCN-1.8 wt%Ace)合金, 研究了平行于生长界面前沿的液相对流对定向凝固胞/枝晶生长行为及胞/枝晶间距的影响. 对于胞晶生长, 在液相对流作用下, 其尖端将会出现分岔, 使得胞晶间距减小, 并且液相对流流速越大, 胞晶尖端分岔越明显, 胞晶组织越细小, 胞晶间距越小. 至于枝晶生长, 其生长行为与胞晶不同. 当抽拉速度较小时, 液相对流作用下枝晶两侧三次臂的生长速度将会超过枝晶尖端生长速度, 形成新的枝晶列, 使得枝晶一次间距减小, 并且液相对流流速越大枝晶一次间距越小; 当抽拉速度较大时, 液相对流作用下迎流侧二次臂生长发达,且会抑制上游枝晶生长, 使得枝晶一次间距增大, 并且液相对流越强枝晶一次间距越大. 关键词： 定向凝固 胞晶间距 枝晶间距 液相对流     

过冷熔体中枝晶生长的相场法数值模拟

利用相场法模拟了过冷纯金属熔体中的枝晶生长过程,研究了各向导性、界面动力学、热扩散和界面能对枝晶生长的影响.结果表明,热噪声可以促发侧向分支的形成,但不影响枝晶尖端的稳态行为;随着各向异性的增加,枝晶尖端生长速度增加,尖端半径减小;当界面动力学系数减小及在界面动力学系数小于1的条件下热扩散系数减小时,枝晶尖端生长速度随之减小,而尖端半径相应增大;界面能趋于增大枝晶尺度并保持界面在扰动下的稳定,界面能越大,形成侧向分支的趋势越小 关键词： 过冷 枝晶生长 相场法 数值模拟     

Experimental evidence for dendrite tip splitting in deeply undercooled,ultrahigh purity Cu

In a recent paper we used a phase-field model of solidification in deeply undercooled pure melts to show that a kinetic instability could result in dendrite tip splitting, and we speculated that such tip splitting could give rise to the phenomenon of spontaneous grain refinement. Here we present evidence, from the as-solidified microstructure of deeply undercooled ultrahigh purity Cu, of what appears to be dendrite tip splitting during recalescence. The significance of this finding in a nongrain refined sample is discussed in terms of the current theories for spontaneous grain refinement.     

Theory of needle-crystal

We investigate the integro-differential equation giving the shape of a steady dendrite growing from a weakly undercooled melt either in two or in three dimensions. Using a generalized WKB analysis, due to Kruskal and Segur, we explicitly show that isotropic surface tension prohibits the growth of needle-crystal, introducing transcendentally small terms at the tip, in agreement with our numerical data.     

定向倾斜枝晶生长规律及竞争行为的相场法研究

采用多相场模型对定向凝固过程中倾斜枝晶生长进行了研究, 模拟了单一取向枝晶列的演化规律及不同取向枝晶列汇聚生长竞争淘汰行为. 结果表明, 枝晶尖端过冷度随倾斜角度的增大而增大, 即相同条件下倾斜枝晶尖端位置总是低于非倾斜枝晶; 汇聚生长时择优取向枝晶总是阻挡非择优取向枝晶, 但在抽拉速度较低时, 由于溶质扩散场的相互重叠, 晶界处择优取向枝晶的生长受到相邻非择优枝晶的影响而延缓, 这可能导致非择优取向枝晶淘汰择优取向枝晶.     

Fractal growth at dendrite tips in an ion-irradiated thin solid film

Summary Experimental observations of fractal growth at dendrite tips during crystalline-to-amorphous phase transition in an ion-irradiated Mo₆₅Ni₃₅ thin film are reported. It was found that the observed anisotropic fractal patterns were of a DLA type but not exactly self-similar. The possible mechanism of this exception to the ordinary parabolic tip growth of the dendrites is discussed.