Integrated optical Mach-Zehnder modulator based on polycrystalline BaTiO3

Good-quality polycrystalline BaTiO3 thin films are deposited on MgO substrates by pulsed laserdeposition. The deposition parameters are optimized to achieve optical-quality films with an attenuation coefficient of 4 dB/cm at the 633-nm wavelength. Thin-film electro-optic Mach-Zehnder modulators are fabricated with standard lithography and ion-beam etching. The waveguides patterned by lithography are the ridge type, and they ensure single-mode propagation in the wavelength range of 633-1550 nm. An electro-optic coefficient of 22 pm/V is estimated for the polycrystalline BaTiO3 films.     

Effects of initial crystal size of diamond powder on surface residual stress and morphology in polycrystalline diamond (PCD) layer

Polycrystalline diamond compacts (PDC) were synthesized using diamond powder of average crystal size 3-20 μm by the Ni 70 Mn 25 Co 5 alloy infiltration technique at high temperature and high pressure (HPHT).The surface residual stress of polycrystalline diamond (PCD) layer was measured using micro-Raman spectroscopy with hydrostatic stress model and X-ray diffraction (XRD).Measurements of the stress levels of PCDs show that the residual compressive stresses range from 0.12 to 0.22 GPa,which increase with th...     

To the synthesis of polycrystalline diamond

Abstract

The sintering system “Diamond-Graphite-Cobalt” is investigated by means of a High Pressure - High Temperature - Belt - Apparatus. Described are the sintering conditions used and some of the properties of the compacts obtained. Good sintering structures and hard PCD (up to 50 GPa) were obtained at 7,5 GPa and 1500°C.     

纳米引晶法选择性生长金刚石薄膜

通过传统的光刻工艺和纳米引晶技术,在抛光的单晶Si衬底上形成带有 超细金刚石纳米粉的引晶图案,并利用该图案与抛光Si处金刚石成核密度的巨大差异,实现 金刚石薄膜的高选择比生长。该方法具有工艺简单、沉积效率高、选择比高、对底无任何损 伤等优点。同时,这种方法很容易在不同衬底上实现金刚石薄膜的大面积选择性生长。     

Hopping conductivity in polycrystalline diamond films

The results of the experimental study of the conductivity of a polycrystalline diamond film by dielectric spectroscopy are presented. A diamond film about 200 μm thick was grown by microwave plasma-assisted chemical vapor deposition for 180 h. Two pronounced local peaks in the frequency dependence of the conductivity were observed. The relevant frequencies were temperature-dependent. These data permit us to hypothesize that the hopping mechanism of conductivity occurs in the polycrystalline diamond film. Two types of electrically active centers with different activation energies and relaxation times are involved in the conductivity.     

Hydrogenation kinetics of carbonaceous layers on polycrystalline iron

Carbonaceous layers were formed on iron by the $\text{CO}\text{H}{}_2$ reaction at 560 K and 1 bar total pressure. These layers were characterized by the C 1 s electron binding energy and peak area. Subsequently they were hydrogenated in 1 bar H₂ at 560 K to predominantly methane. There are two distinct stages of carbon hydrogenation: a fast initial stage where the rate depends sensitively on the total amount of deposited carbon, and a very slow second stage. The first stage corresponds to the removal of CH_x and carbidic carbon phases whereas the presence of graphitic carbon is indicated during the second stage. The initial rate of carbon hydrogenation is directly proportional to the rate of methane production from $\text{CO}\text{H}{}_2$ (at constant carbon coverage). From this behavior it was concluded that methane is formed by a direct hydrogenation of atomically adsorbed carbon.     

X-ray topographic identification and measurement of plastic strains and elastic stresses in single crystallites of polycrystalline diamond layers

The well-known phenomenon of asterism is used as the basis for the development of an X-ray topographic method to identify and measure plastic strains and residual elastic stresses in single crystallites more than 3 μm in size in polycrystalline diamond layers. The amount of asterism is used as a quantitative measure of plastic strains in crystallites. The distribution of crystallites over the amount of asterism in 40-to 670-μm-thick microwave-plasma-deposited polycrystalline diamond layers is obtained. Shear plastic strains, which cause a misorientation from 0.4′ to 1.5° between different areas of a crystallite, are observed for the first time. The residual elastic stresses calculated in plastically strained crystallites vary between 2.7 kPa and 0.84 GPa.     

Photoacoustic spectroscopy of diamond powders and polycrystalline films

Photoacoustic spectroscopy is used to study optical absorption in diamond powders and polycrystalline films. The photoacoustic spectra of diamond powders with crystallite sizes in the range from ∼100 μm to 4 nm and diamond films grown by chemical vapor deposition (CVD) had a number of general characteristic features corresponding to the fundamental absorption edge for light with photon energies exceeding the width of the diamond band gap (∼5.4 eV) and to absorption in the visible and infrared by crystal-structure defects and the presence of non-diamond carbon. For samples of thin (∼10 μm) diamond films on silicon, the photoacoustic spectra revealed peculiarities associated with absorption in the silicon substrate of light transmitted by the diamond film. The shape of the spectral dependence of the amplitude of the photoacoustic signal in the ultraviolet indicates considerable scattering of light specularly reflected from the randomly distributed faces of the diamond crystallites both in the polycrystalline films and in the powders. The dependence of the shape of the photoacoustic spectra on the light modulation frequency allows one to estimate the thermal conductivity of the diamond films, which turns out to be significantly lower than the thermal conductivity of single-crystal diamond. Fiz. Tverd. Tela (St. Petersburg) 39, 1787–1791 (October 1997)     

Strength and plastic deformation of polycrystalline diamond composites

ABSTRACT

The use of nanopolycrystalline diamond has allowed a systematic study on deformation of polycrystalline diamond composites (PCDCs). Bulk PCDCs samples containing either Co or SiC as a binding agent were deformed under high pressure and temperature to strains up to 18% at strain rates ～10^?5?s^?1. All samples exhibit strong work hardening. The strength of PCDCs depends on the amount and type of binding agents and is consistently weaker than that of diamond single crystals. The weakening may be due to the binder materials, which play an important role in affecting grain boundary structures. In SiC-based PCDC, significant grain fragmentation occurs. Nearly all grain boundaries are wetted by SiC after large deformation, resulting in lower strength. In Co-based PCDC, the microstructure is dominated by dislocations, deformation twins, and separated grain boundaries. The density of deformation twins increases significantly with strain, with the twin domain width reaching as low as 10–20?nm at 14% strain.     

Integrated microwave photonics

Microwave photonics (MWP) is an emerging field in which radio frequency (RF) signals are generated, distributed, processed and analyzed using the strength of photonic techniques. It is a technology that enables various functionalities which are not feasible to achieve only in the microwave domain. A particular aspect that recently gains significant interests is the use of photonic integrated circuit (PIC) technology in the MWP field for enhanced functionalities and robustness as well as the reduction of size, weight, cost and power consumption. This article reviews the recent advances in this emerging field which is dubbed as integrated microwave photonics. Key integrated MWP technologies are reviewed and the prospective of the field is discussed.     

High pressure sintering behavior of polycrystalline diamond with tungsten

Polycrystalline diamond was investigated under high pressure and high temperature of 5.0 GPa and 1100–1500 °C in the presence of tungsten. In situ resistance measurements indicated that reactions between diamond and tungsten happened at about 960 °C. Phase analysis demonstrated that WC increased and meta-stability of W₂C decreased clearly at the higher temperature. It is clear from the characterization of the sintered body that the electrical resistance decreased and the density of specimens increased as the sintering temperature rose. The specimen sintered at 1500 °C has a homogeneous microstructure and good conductivity.     

Brillouin spectroscopy on monodomains of thin polycrystalline layers of molecular crystals

An unconventional Brillouin-spectroscopic technique is proposed to determine elastic stiffness tensor coefficients of molecular crystals. With 90A Brillouin measurements on thin monodomains of melt-crystallized films (about 30 μm thickness) the need to grow large single crystals is avoided. Measurements on sym-difluorotetrachloroethane and perfluoroeicosane are presented.     

Influence of structural characteristics on the thermal conductivity of polycrystalline diamond films

By analyzing the signal formed by the photoacoustic effect as a function of the light modulation frequency, it is shown that this effect may be used to determine the thermal conductivity of diamond materials. The method is checked experimentally for two types of polycrystalline diamond films grown by chemical vapor deposition with the gaseous medium activated by a dc discharge and a microwave discharge. The data obtained on the thermal conductivity of the films are discussed with reference to the results of an investigation of the optical absorption, Raman light scattering, and cathodoluminescence of similar films. It is shown that the thermal conductivity of polycrystalline diamond films depends on the structural characteristics, which are determined by the deposition conditions. Fiz. Tverd. Tela (St. Petersburg) 40, 1221–1225 (July 1998)     

High-Q microwave photonic filter with a tuned modulator

We propose the use of tuned electro-optic or electroabsorption external modulators to implement high-quality (high-Q) factor, single-bandpass photonic filters for microwave signals. Using this approach, we experimentally demonstrate a transversal finite impulse response with a Q factor of 237. This is to our knowledge the highest value ever reported for a passive finite impulse-response microwave photonic filter.     

X-ray photoelectron and Raman studies of microwave Plasma Assisted Chemical Vapour Deposition (PACVD) diamond films

X-ray photoelectron and Raman spectroscopies were used to investigate the chemical and the structural properties of thin diamond films synthesised by Plasma Assisted Chemical Vapour Deposition (PACVD). Continuous polycrystalline diamond films were grown under different plasma conditions and based on the combination of detailed XPS and Raman spectroscopic analysis two main topics are highlighted (i) the stress measurements were discussed by distinguishing clearly the chemical effects from the mechanical effects; (ii) an electronic gap at 2.7 eV probed by Raman resonance that corresponds to an energy loss peak on the XPS carbon signal, was related to the surface hydrogenation.     

Continuously tunable photonic microwave filter based on a spatial light modulator

An optical microwave filter architecture which can be continuously tuned is proposed and demonstrated. The architecture is based on a nematic liquid crystal spatial light modulator in parallel configuration and has the potential to control a large number of taps. Proof-of concept experimental results are provided.     

Thermal conductivity of polycrystalline CVD diamond: Experiment and theory

The temperature dependences of thermal conductivity κ of polycrystalline CVD diamond are measured in the temperature range from 5 to 410 K. The diamond sample is annealed at temperatures sequentially increasing from 1550 to 1690°C to modify the properties of the intercrystallite contacts in it. As a result of annealing, the thermal conductivity decreases strongly at temperatures below 45 K, and its temperature dependence changes from approximately quadratic to cubic. At T > 45 K, the thermal conductivity remains almost unchanged upon annealing at temperatures up to 1650°C and decreases substantially at higher annealing temperatures. The experimental data are analyzed in terms of the Callaway theory of thermal conductivity [9], which takes into account the specific role of normal phonon-phonon scattering processes. The thermal conductivity is calculated with allowance for three-phonon scattering processes, the diffuse scattering by sample boundaries, the scattering by point and extended defects, the specular scattering by crystallite boundaries, and the scattering by intercrystallite contacts. A model that reproduces the main specific features of the thermal conductivity of CVD diamond is proposed. The phonon scattering by intercrystallite contacts plays a key role in this model.