Enzymatic detection of glucose using fluoride-selective electrodes with polymeric membranes

The feasibility of using polymeric membrane fluoride-selective electrodes based on zirconium(IV) 5,10,15,20-tetraphenylporphyrin as a detector in a flow-injection analysis (FIA) system for glucose determination was examined. The optimization of enzymatic reactions, FIA system configuration and enzyme-immobilization process was performed. It was shown that the resulting flow-injection system exhibits good working parameters, such as reproducibility, linear range of glucose concentration (3 × 10⁻³–10⁻¹ M), sampling rate (60 samples per minute) and lifetime (over 1 month). The performance of the polymeric membrane electrode was similar to that of a crystalline LaF₃ electrode. The results of glucose determination in synthetic samples with the proposed system show good agreement with real glucose concentrations.     

A new Zn(II)-selective potentiometric sensor based on 4-tert-butylcalix[4]arene in PVC matrix

Poly(vinyl chloride) (PVC) based membranes containing 4-tert-butylcalix[4]arene (I) as an electroactive material alongwith anion excluder sodiumtetraphenylborate (NaTPB) and plasticizer tri-butylphosphate (TBP) have been developed to fabricate a new zinc-selective sensor. Out of various compositions, the best performance was exhibited by the membrane having I, NaTPB, TBP and PVC in the ratio 8:5:100:200 (w/w). The sensor works well in the concentration range 9.8 × 10⁻⁶ to 1.0 × 10⁻¹ mol dm⁻³ with a near-Nernstian slope of 28.0 ± 1.0 mV/decade of activity. The detection limit is down to 5.0 × 10⁻⁷ mol dm⁻³. The working pH range of this sensor is 2.5–4.3 and it works well in partially non-aqueous medium up to 15% (v/v) (methanol, ethanol and acetone). It exhibits a fast response time of 30 s and could be used for more than four months without any considerable change in response characteristics. It has excellent selectivity for Zn(II) over other mono-, bi- and trivalent cations which have been reported to cause interference in the working of other sensors. It has been successfully used as an indicator electrode in the potentiometric titration of Zn(II) against EDTA and also to estimate zinc ions in industrial waste waters.     

Planar potentiometric sensors based on Au and Ag microelectrodes and conducting polymers for flow-cell analysis

Back-side contact Au and Ag microelectrodes were used as transducers to construct planar all-solid-state electrodes suitable for flow-through analysis. The microsensors were based on plasticized PVC potassium-selective membranes containing ion-electron conducting polymer—polypyrrole doped with di(2-ethylhexyl) sulfosuccinate. The proposed technique allowed simple construction of microsensors in one step, by membrane solution casting directly on the surface of the planar metallic transducers. The performance of the microsensors based on Au and Ag transducers were determined and compared with planar sensors based on internal electrolyte immobilized in polyHEMA. The addition of the polypyrrole to the membrane composition did not influence on the selectivity, reproducibility and long-term stability of the microsensors but improved their standard potential stability in time in comparison with coated-wire type sensors. Moreover, all-solid-state microsensors based on Au transducers exhibited better signal stability than Ag based sensors.     

Electroanalytical performance of a terbium(III)-selective sensor based on a neutral ionophore in environmental and medicinal samples

A new highly selective terbium(III) electrode was prepared with a polymeric film doped using S-2-benzothiazolyl-2-amino-α-(methoxyimino)-4-thiazolethiol acetate as an electroactive material, benzyl acetate (BA) as a plasticizer, and potassium tetrakis(4-chlorophenyl) borate (KTpClPB) as an anionic site in the percentage ratio 3.17:1.58:63.4:31.7 (ionophore-KTpClPB-BA-PVC, w/w). The electrode exhibited a linear response with a near Nernstian slope of 19.5 mV/decade within the concentration range 1.5 × 10⁻⁷−1.0 × 10⁻² M terbium ions, with a working pH range from 2.0 to 8.0, and a fast response time of 10 s and presented satisfactory reproducibility. The limit of detection was 9.3 × 10⁻⁸ M. The results show that this electrode can be used in ethanol media up to 30% (v/v) concentration without interference. It can be used for 3 months without any considerable divergence in the potentials. Selectivity coefficients for terbium(III) with respect to many cations were investigated. The electrode is highly selective for terbium(III) ions over a large number of monovalent, bivalent, and trivalent cations. This shows the valuable property of the proposed electrode. The stability constant of the ionophore towards Tb³⁺ ions was determined with the sandwich membrane method. It was successfully used as an indicator electrode in potentiometric determination of terbium(III) ions with EDTA and in direct determination in tap water and binary mixtures with quantitative results. The utility of the proposed electrode was also determined in the presence of ionic and nonionic surfactants and in the presence of fluoride ions in four pharmaceutical (mouthwash) preparations. Figure Structure of S-2-Benzothiazolyl-2-amino-α-(methoxyimino)-4-thiazolethiol acetate     

A cobalt(II)-selective PVC membrane based on a Schiff base complex of N,N′-bis(salicylidene)-3,4-diaminotoluene

A new PVC membrane electrode for Co²⁺ based on N,N′-bis(salicylidene)-3,4-diaminotoluene, an excellent neutral carrier, has been fabricated using sodium tetraphenylborate (NaTPB) as an anionic excluder and dioctylphthalte (DOP) as a solvent mediator. The electrode exhibits a linear potential response in the concentration range of 7.9 × 10⁻⁸ to 1.0 × 10⁻¹ M with a slope of 30 ± 0.2 mV per decade. The detection limit of the proposed sensor is 5.0 × 10⁻⁸ M and it can be used over a period of 5 months. The proposed sensor revealed good selectivity over a wide variety of other cations including alkali, alkaline earth, heavy and transition metals and could be used in the pH range of 2.0-9.0. This electrode was successfully applied for the determination of Co²⁺in real samples and as an indicator electrode in potentiometric titration of cobalt ions.     

Development of a tubular fluoride potentiometric detector for flow analysis: evaluation and analytical applications

In this work a construction procedure for tubular fluoride electrode to be used in flow systems is outlined. The electrode was constructed from a commercially available, LaF₃ single crystal. Principal advantages of the flow detector presented include simplicity of construction, robustness, durability, low cost and easy coupling into any point of a flow manifold.Evaluation of the intrinsic working characteristics of the potentiometric detector in a low dispersion manifold is presented with respect to analytical and dynamic parameters. The constructed detector has similar working characteristics to those of the conventional fluoride electrodes, namely the detection limit, lower limit of linear response and operational pH range.The analytical usefulness of the constructed device was assessed in a flow system developed for fluoride determination in toothpaste, tablet, collutory and water samples for which the reference procedures suggest the determination of fluoride ion with a conventional ion selective electrode.     

A novel ratiometric fluorescent Fe sensor based on a phenanthroimidazole chromophore

Phenanthroimidazole derivative 1 has been developed as a rare example of ratiometric fluorescent sensors for Fe³⁺. Interestingly, upon treatment with Fe³⁺, the sensor displayed a ratiometric fluorescent response with an enhancement of the ratios of emission intensities at 440 and 500 nm from 0.36 to 3.24. The detection range of the sensor for Fe³⁺ is in the 1.0 × 10⁻⁵-1.5 × 10⁻⁴ M concentration range and the detection limit is 5.26 × 10⁻⁶ M. In addition, the sensor showed good selectivity to Fe³⁺ with the selectivity coefficients (KFe3+=SFe3+/S₀) of Fe³⁺ over other metal ions tested in the range of 5-68.     

Characterization of a urea optical sensor based on polypyrrole

A new optical sensor for urea determination is presented. It is based on the enzymatic reaction with urease, which is first photoimmobilized with polyacrylamide onto a chemically polymerized polypyrrole (PPy) film. The main advantage of this sensor is that no indicator dye or pH indicator is needed, because PPy itself acts as the support and the indicator. These PPy films show an absorbance spectrum in the near IR range which is pH dependent. The variation of absorbance is thus directly related to the change of pH caused during the enzymatic reaction, which is also dependent on the urea concentration. The linear range of the sensor is from 0.06 to 1 M of urea, which is the common level of urea concentration found in blood and urine samples.     

A fluorescence ratiometric sensor for hypochlorite based on a novel dual-fluorophore response approach

A fluorescence ratiometric sensor for OCl⁻ has been developed based on a novel dual fluorophore response approach. The sensor molecule contains a coumarin fluorophore and a rhodamine fluorophore, and the two fluorophores are directly linked to an OCl⁻ recognition group. The structure of the sensor was characterized by ESI-MS, NMR, and X-ray crystallographic analysis. Upon treatment with OCl⁻, both fluorophores in the sensor responded simultaneously at two separate optical windows, with large enhancement of the fluorescence ratio (I₅₇₈/I₅₀₁) from 0.01 to 39.55. The fluorescence ratios for the sensor showed a good linearity with the concentration of OCl⁻ in the range of 0.2–40 μM and the detection limits is 0.024 μM (S N⁻¹ = 3). Investigation of reaction products indicated that the sensor reaction with OCl⁻ produced two new fluorescent molecules, which were responsible for the fluorescence changes in two optical windows. In addition, the sensor showed high selectivity to OCl⁻ over other reactive oxygen species, reactive nitrogen species, cations, and anions. The sensor has also been successfully applied to detection of OCl⁻ in natural water samples with satisfactory recovery.     

Development of an electrochemical sensor based on Schiff base for Cu(II) determination at nano level in river water and edible materials

Plasticised membranes using 2-[{(2-hydroxyphenyl)imino}methyl]-phenol (L₁) and 2-[{(3-hydroxyphenyl)imino}methyl]-phenol (L₂), have been prepared and investigated as Cu²⁺ ion-selective sensors. Effect of various plasticisers, namely, dibutyl phthalate (DBP), dibutyl sebacate (DBS), benzyl acetate (BA), o-nitrophenyloctylether (o-NPOE) and anion excluders, oleic acid (OA) and sodium tetraphenylborate (NaTPB) was studied and improved performance was observed in several instances. Optimum performance was observed with membranes of (L₁) having composition L₁ : DBS : OA : PVC in the ratio of 6 : 54 : 10 : 30 (w/w, %). The sensor works satisfactorily in the concentration range 3.2 × 10^?8–1.0 × 10^?1 mol L^?1 with a Nernstian slope of 29.5 ± 0.5 mV decade^?1 of a _cu²⁺ . The detection limit of the proposed sensor is 2.0 × 10^?8 mol L^?1 (1.27 ng mL^?1). Wide pH range (3.0–8.5), fast response time (7 s), sufficient (up to 25% v/v) non-aqueous tolerance and adequate shelf life (3 months) indicate the utility of the proposed sensor. The potentiometric selectivity coefficients as determined by matched potential method indicate selective response for Cu²⁺ ions over various interfering ions, and therefore could be successfully used for the determination of copper in edible oils, tomato plant material and river water.     

Batch and hydrodynamic monitoring of vitamin C using novel periodate selective sensors based on a newly synthesized Ni(II)-Schiff bases complexes as a neutral receptors

A highly selective membrane electrodes based on a two newly synthesized nickel (II) Schiff bases, [NiL¹] and [NiL²] where L¹ and L² are N,N/bis(salicylaldehyde)4,5-dimethyl-1,2-phenylenediamine (H₂L¹) and N,N/bis(salicylaldehyde)4,5-dichloro-1,2-phenylenediamine (H₂L²) were used as a neutral carrier ionophores for static and hydrodynamic potentiometric mode of operations for the determination of periodate. Under static mode of operation, the sensors displayed a near-Nernstian slope of −66.1 ± 0.8 and −59.9 ± 1.1 mV decade⁻¹ of activity and detection limits to 5.2 × 10⁻⁶ and 7.3 × 10⁻⁶ mol L⁻¹ for the sensors based on [NiL¹] and [NiL²], respectively. Under hydrodynamic mode of operation (FIA), the slope of the calibration plot, limit of detection, and working linear range were −71.1 mVdecade⁻¹ of activity, 7.3 × 10⁻⁶ and 1.0 × 10⁻⁵ to 1.0 × 10⁻³ mol L⁻¹, respectively. The response time of the sensors in whole concentration ranges was very short (<10 s). The response of the sensors was independent on the pH range of 3-8. A tubular version was further developed and coupled to a flow injection system for ascorbic acid (AA) determination in beverages and pharmaceutical preparations. This approach was achieved by selecting a 50-cm reactor and an overall flow of 3 mL min⁻¹, and injecting volume 100 μL of AA standards in a 1.0 × 10⁻⁴ mol L⁻¹ IO₄⁻ solution. Under these conditions, a linearity range of 2-13 μg mL⁻¹, with a slope of 4.97 mV (mg/L)⁻¹ (r² = 0.9995), detection limit 0.9 mg L⁻¹ and a reproducibility of ±1.1 mV (n = 5) was recorded. This simple and inexpensive flow injection analysis manifold, with a good potentiometric detector, enabled the analysis of ∼50 samples h⁻¹ without requiring pretreatment procedures. An average recovery of 98.8% and a mean standard deviation of 1.3% were obtained.     

A new potentiometric sensor based on a high-performance composite for nanomolar determination of mercury (II) in environmental samples

A new potentiometric sensor for the rapid determination of Hg²⁺ based on modified carbon paste electrode consisting of room temperature ionic liquid, 1-Butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF₆), multi-walled carbon nanotubes (MWCNTs), alumina nanoparticles and a synthetic macrocyclic diamide ‘7,10,13-triaza-1-thia-4,16-dioxa-6,14-dioxo-2,3;17,18-dinaphtho-cyclooctadecane’ as an efficient ionophore was constructed. Prepared composite is an ideal paste because it has low drift of potential, high selectivity and fast response time (10 s), which leads to a more stable potential signal. The morphology and properties of electrodes surface were characterised by scanning electron microscopy (SEM) and electrochemical impedance spectroscopy. A linear dynamic range of 2.01–2.01 × 10⁷ µg L^?1 with detection limit of 1.40 µg L^?1 Hg²⁺ was obtained at pH range of 2.5 to 4.5. The prepared modified electrode shows several advantages such as simple preparation method, high stability of the composite paste, high sensitivity, long-term life time (at least 13 weeks) and remarkable potentiometric reproducibility. The modified electrode was successfully applied for the accurate determination of trace amounts of Hg ²⁺ in environmental samples.     

An interference-free first generation alcohol biosensor based on a gold electrode modified by an overoxidised non-conducting polypyrrole film

An interference-free first generation alcohol biosensor based on alcohol oxidase immobilized, by glutaraldehyde co-crosslinking with bovine serum albumin, on a perm-selective electropolymerized film modified gold electrode is described. The use, in place of platinum, of a gold electrode, properly conditioned by an electrochemical pre-treatment, allowed the elimination of the electrode fouling and of the interference caused by the direct alcohol oxidation at the electrode surface. The efficiency of overoxidized polypyrrole and poly-ortho-phenylendiamine as anti-interferent perm-selective films towards the most common electroactive interferents was also investigated.The low response time and the fabrication procedure employed in this study allowed the use of the biosensor in a flow injection system equipped with a conventional thin-layer electrochemical cell.The biosensor showed a high sensitivity, a good stability and a complete suppression of electroactive interferences in operational conditions. Biosensor performances were tested by the rapid determination of the alcohol content in just diluted wine samples and the results compared well with those obtained with the classical method of distillation.     

Development of glucose amperometric biosensor based on a novel attractive enzyme immobilization matrix: amino derivative of thiacalix[4]arene

Calixarenes and their derivatives may be a promising material for enzyme immobilization owing to their particular configuration, unique molecule recognition function and aggregation properties. In this paper, p-tert-butylthiacalix[4]arene tetra-amine (TC4TA) was first used as enzyme immobilization material. This attractive material was exploited for the mild immobilization of glucose oxidase (GOD) to develop glucose amperometric biosensor. GOD was strongly adsorbed on the TC4TA modified electrode to form TC4TA/GOD composite membrane. The adsorption mechanism was driven from the covalent bond between amino-group of TC4TA and carboxyl group of GOD and molecule recognition function of TC4TA. Amperometric detection of glucose was evaluated by holding the modified electrode at 0.60 V (versus SCE) to oxidize the hydrogen peroxide generated by the enzymatic reaction. The sensor (TC4TA/GOD) showed a relative fast response (response time was about 5 s), low detection limit (20 μM, S/N = 3), and high sensitivity (ca. 10.2 mA M⁻¹ cm⁻²) with a linear range of 0.08–10 mM of glucose, as well as a good operational and storage stability. In addition, optimization of the biosensor construction, the effects of the applied potential as well as common interfering compounds on the amperometric response of the sensor were investigated and discussed herein.     

Construction of a novel electrochemical sensor based on molecularly imprinted polymers for the selective determination of chlorpyrifos in real samples

We present a novel electrochemical sensor based on an electrode modified with molecularly imprinted polymers for the detection of chlorpyrifos. The modified electrode was constructed by the synthesis of molecularly imprinted polymers by a precipitation method then coated on a glassy carbon electrode. The surface morphology of the modified electrode was characterized by using field‐emission scanning electron microscopy and transmission electron microscopy. The performance of the imprinted sensor was thoroughly investigated by using cyclic voltammetry and differential pulse voltammetry. The imprinted electrochemical sensor displayed high repeatability, stability, and selectivity towards the template molecules. Under the optimal experimental conditions, the peak current response of the imprinted electrochemical sensor was linearly related to the concentration of chlorpyrifos over the range 1 × 10⁻¹⁰–1 × 10⁻⁵ mol/L with a limit of detection of 4.08 × 10⁻⁹ mol/L (signal‐to‐noise ratio = 3). Furthermore, the proposed molecularly imprinted electrochemical sensor was applied to the determination of chlorpyrifos in the complicated matrixes of real samples with satisfactory results. Therefore, the molecularly imprinted polymers based electrochemical sensor might provide a highly selective, rapid, and cost‐effective method for chlorpyrifos determination and related analysis.     

An oxygen reduction sensor based on a novel type of porous carbon composite membrane electrode

The development of a simple, efficient and sensitive sensor for dissolved oxygen is proposed using a novel type of porous carbon composite membrane/glassy carbon electrode based on the low-cost common filter paper by a simple method. The resulting device exhibited excellent electrocatalytic activities toward the oxygen reduction reaction. Scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and electrochemical measurements demonstrated that the porous morphology and uniformly dispersed Fe₃C nanoparticles of the PCCM play an important role in the oxygen reduction reaction. A linear response range from 2μmol/L up to 110 μmol/L and a detection limit of 1.4 μmol/L was obtained with this sensor. The repeatability of the proposed sensor, evaluated in terms of relative standard deviation, was 3.0%. The successful fabrication of PCCM/GC electrode may promote the development of new porous carbon oxygen reduction reaction material for the oxygen reduction sensor.     

Potentiometric flow injection sensing system for determination of heparin based on current-controlled release of protamine

A flow injection system incorporated with a polycation-sensitive polymeric membrane electrode in the flow cell is proposed for potentiometric determination of heparin. An external current in nano-ampere scale is continuously applied across the polymeric membrane for controlled release of protamine from the inner filling solution to the sample solution, which makes the electrode membrane regenerate quickly after each measurement. The protamine released at membrane–sample interface is consumed by heparin injected into the flow cell via their strong electrostatic interaction, thus decreasing the measured potential, by which heparin can be detected. Under optimized conditions, a linear relationship between the potential peak height and the concentration of heparin in the sample solution can be obtained in the range of 0.1–2.0 U mL⁻¹, and the detection limit is 0.06 U mL⁻¹. The proposed potentiometric sensing system has been successfully applied to the determination of heparin in undiluted sheep whole blood.     

Inhibitive detection of benzoic acid using a novel phenols biosensor based on polyaniline–polyacrylonitrile composite matrix

A novel sensitive and stable phenols amperometric biosensor, based on polyaniline–polyacrylonitrile composite matrix, was applied for determination of benzoic acid. The electrochemical biosensor functioning was based on the inhibition effect of benzoic acid on the biocatalytic activity of the polyphenol oxidase (PPO) to its substrate (catechol) in 0.1 M phosphate buffer solution (pH 6.5). A potential value of −50 mV versus SCE, and a constant catechol concentration of 20 μM were selective to carry out the amperometric inhibition measurement. The kinetic parameters Michaelis-Menten constant and maximum current (I_max) in the absence and in the presence of benzoic acid were also evaluated and the possible inhibition mechanism was deduced. The inhibiting action of benzoic acid on the polyphenol oxidase electrode was reversible and of the typical competitive type, with an apparent inhibition constant of 38 μM. This proposed biosensor detected levels of benzoic acid as low as 2 × 10⁻⁷ M in solution. In addition, the effects of temperature, pH value of solution on the inhibition and the interferences were investigated and discussed herein. Inhibition studies revealed that the proposed electrochemical biosensor was applicable for monitoring benzoic acid in real sample such as milk, yoghurt, sprite and cola.     

A cerium(III) selective polyvinyl chloride membrane sensor based on a Schiff base complex of N,N'-bis[2-(salicylideneamino)ethyl]ethane-1,2-diamine

A polyvinyl chloride (PVC) based membrane sensor for cerium ions was prepared by employing N,N′-bis[2-(salicylideneamino)ethyl]ethane-1,2-diamine as an ionophore, oleic acid (OA) as anion excluder and o-nitrophenyloctyl ether (o-NPOE) as plasticizer. The plasticized membrane sensor exhibits a Nernstian response for Ce(III) ions over a wide concentration range (1.41 × 10⁻⁷ to 1.0 × 10⁻² M) with a limit of detection as low as 8.91 × 10⁻⁸ M. It has a fast response time (<10 s) and can be used for 4 months. The sensor revealed a very good selectivity with respect to common alkali, alkaline earth and heavy metal ions. The response of the proposed sensor is independent of pH between 3.0 and 8.0. It was used as an indicator electrode in potentiometric titration of fluoride, carbonate and oxalate anions and determination of cerium in simulated mixtures.