聚缬氨酸修饰电极在抗坏血酸共存下选择性测定去甲肾上腺素

利用循环伏安法制备了聚缬氨酸修饰电极,在缬氨酸浓度为0.01 mol/L的磷酸盐缓冲溶液(pH=9.0)中,起止电位范围为1.0～2.4 V,以40 mV/s扫描速率循环扫描9周进行聚合. 聚缬氨酸膜对去甲肾上腺素(NE)的电化学氧化具有明显的催化作用. 研究了NE在聚缬氨酸修饰电极上的电化学行为,建立了测定NE的电化学分析新方法. pH值在2.2～8.0范围内,研究了磷酸盐缓冲溶液pH值对NE电化学行为的影响. 结果表明,氧化还原峰电位随pH值升高发生负移;在pH=4.0磷酸盐缓冲溶液中,NE在修饰电极上呈现1对灵敏的氧化还原峰,利用循环伏安法测定NE还原峰电流可排除抗坏血酸(AA)干扰. NE在聚缬氨酸修饰电极上的还原峰电流与其浓度在4.6×10-7～1.1×10-5 mol/L和1.1×10-5～1.2×10-4 mol/L范围内呈良好线性关系;相关系数分别为0.995 7和0.991 8;检出限(S/N=3)为8.0×10-8 mol/L;其回归方程为ipc(A)=6.80×10-7+1.05c,ipc(A)=1.23×10-5+0.16c. 修饰电极具有良好的灵敏度、选择性和稳定性,可用于去甲肾上腺素针剂样品分析.     

聚对氨基酚修饰电极的制备及其对尿酸的催化氧化作用

采用循环伏安法制备了聚对氨基酚薄膜修饰玻碳电极, 研究了尿酸在该修饰电极上的电化学行为, 建立了循环伏安法测定尿酸的新方法. 研究发现: 在pH 5.6的磷酸盐缓冲溶液中, 以0.1 mol/L KCl作支持电解质, 聚对氨基酚修饰电极对尿酸存在灵敏的氧化作用, 应用循环伏安法对尿酸进行定量分析, 线性范围为1.0×10-6～4.0×10-5 mol/L, 检出限为8×10-7 mol/L. 对2.0×10-5 mol/L尿酸平行测定5次, 相对标准偏差为4.0%.     

黄嘌呤和鸟嘌呤在石墨烯-聚唑类化合物修饰电极上电化学行为

采用滴涂法和循环伏安法制备石墨烯-聚唑类化合物复合膜修饰玻碳电极,分别用循环伏安法和差分脉冲伏安法研究黄嘌呤和鸟嘌呤混合物在修饰电极上的电化学行为。在0.2 mol/L的磷酸盐缓冲液(p H 5.5)中,黄嘌呤和鸟嘌呤混合物在修饰的玻碳电极上具有较好的电化学行为。鸟嘌呤和黄嘌呤分别在4.0×10~(-4)~4.0×10~(-6)mol/L和4.0×10~(-5)~4.0×10~(-8)mol/L范围内有较好的电化学响应,鸟嘌呤和黄嘌呤检出限分别为4.0×10~(-7)mol/L和4.0×10~(-9)mol/L。方法用于同时测定人体尿液中鸟嘌呤和黄嘌呤,回收率分别为102.1%~105.9%和96.9%~106.5%。     

盐酸氯丙嗪在聚L-苏氨酸/多壁碳纳米管修饰电极上的电化学行为

以玻碳电极为基底成功制备了聚L-苏氨酸poly(L-Threonine)/多壁碳纳米管(MCNTs)修饰电极(p-L-Thr/ MCNTs/GCE).研究了盐酸氯丙嗪在该修饰电极上的电化学行为.该修饰电极对盐酸氯丙嗪具有明显的电催化氧化作用,并对此电极进行显微表征.本研究将此修饰电极用于流动注射不可逆双安培(FL-IB)体系的构建,即利用盐酸氯丙嗪在p-L-Thr/MCNTs/GCE上的氧化和高锰酸钾(KMnO4)在另一支铂电极上的还原构建了双安培检测体系,成功的建立了在外加电压为0 V条件下流动注射双安培法直接测定盐酸氯丙嗪的方法.在0 V外加电压下,在1 mol/L pH6.8的磷酸盐缓冲溶液的载液中,氧化峰峰电流与盐酸氯丙嗪浓度在2.0×10-6mol/L～4.0×10-5 mol/L范围内呈良好的线性关系,其线性回归方程为i (nA)=9.73×107C-50(r=0.9993,n=6),在4.0×10-5mol/L～10-3 mol/L范围内呈线性关系,其线性回归方程为i (nA)=2.33×107C+4×103 (r=0.9984,n=7),方法检出限为4.0×10-7 mol/L (S/N=3).连续测定1.00×10-4mol/L的盐酸氯丙嗪标准溶液20次,电流值RSD为2.44%,进样频率为90样/h.该方法具有较高的选择性和灵敏度.对盐酸氯丙嗪片中的盐酸氯丙嗪的含量的测定,结果比较满意.     

聚磺胺嘧啶修饰电极伏安法测定对乙酰氨基酚

利用循环伏安法制备了聚磺胺嘧啶修饰电极, 研究了对乙酰氨基酚在该修饰电极上的电化学行为. 该电极对对乙酰氨基酚有较强的电催化作用. 在pH 9.0的PBS缓冲溶液中, 用循环伏安法和差分脉冲伏安法在该电极上测定了对乙酰氨基酚, 其线性范围分别为4.0×10-6～3.0×10-4 mol/L和2.0×10-7～1.0×10-5 mol/L, 检出限分别为9.0×10-7 mol/L和8.0×10-8 mol/L.     

聚邻氨基苯甲酸-铜复合薄膜修饰电极的制备及其电化学性能

利用聚合物官能团对金属离子的配位作用,在电极表面原位制备了金属粒子。 首先在玻碳电极（GCE）表面电沉积聚邻氨基苯甲酸(PoABA),再化学吸附铜离子(Cu2+),用水合肼还原得到单质铜(Cu0)。 采用扫描电子显微镜和能谱分析表征了聚邻氨基苯甲酸 铜(PoABA-Cu0)复合薄膜的表面形貌和元素构成,研究了PoABA-Cu0修饰电极的电化学性能,并以其检测了过氧化氢（H2O2）。 结果表明,电极表面被修饰上了一层PoABA-Cu0复合薄膜;制备的修饰电极对H2O2具有良好的电催化性能,在邻氨基苯甲酸的聚合圈数为10、Cu2+的吸附时间为10 min、工作电压为-0.3 V时,该修饰电极对H2O2表现出了最佳的检测性能,其线性浓度范围为5.0×10-5～1.0×10-2 mol/L,灵敏度为96.3 μA·L/(mmol·cm),检测限为5.0×10-5 mol/L,且具有较好的稳定性。     

聚L-丝氨酸修饰电极选择性测定去甲肾上腺素

用循环伏安法制备了聚L-丝氨酸修饰玻碳电极,研究了去甲肾上腺素在聚L-丝氨酸修饰玻碳电极上的电化学行为,建立了测定去甲肾上腺素的新方法。实验结果表明:在pH 6.0的磷酸盐缓冲溶液中,聚L-丝氨酸薄膜对去甲肾上腺素的电化学氧化具有明显的催化作用,利用循环伏安法测定其还原峰电流可排除抗坏血酸干扰。去甲肾上腺素检测线性范围为4.0×10-7~1.5×10-4mol/L;检出限为1.0×10-8mol/L。该修饰电极具有良好的灵敏度、选择性和稳定性,已用于针剂样品分析。     

氧化铜-过氧化聚吡咯-还原氧化石墨烯复合膜修饰电极非酶检测葡萄糖

先以氧化石墨烯(Graphen oxide,GO)为阴离子掺杂剂,采用电化学聚合法制备了聚吡咯-氧化石墨烯复合膜(PPy-GO)。分别在0.10 mol/L Na Cl和0.10 mol/L NaOH溶液中对其进行还原和过氧化处理,制得过氧化聚吡咯-还原氧化石墨烯复合膜(OPPy-ERGO)。再以此OPPy-ERGO复合膜为载体,采用电化学沉积法制备了氧化铜-过氧化聚吡咯-还原氧化石墨烯复合膜修饰电极(CuO-OPPy-ERGO/CCE)。通过扫描电镜和电化学方法对此电极进行表征,研究了葡萄糖在此修饰电极上的电化学行为。结果表明,此电极对葡萄糖的电氧化过程表现出高的催化活性和良好的抗干扰能力。在0.20 mol/L NaOH溶液中,安培法检测葡萄糖的线性范围为5.0×10~(-7)~1.0×10~(-3)mol/L,检出限(3Sb)为2.0×10~(-7)mol/L,灵敏度为121.8μA/(mmol·L~(-1))。该电极用于血清中葡萄糖含量的测定,加标回收率为96.0%~110.1%。     

聚L-组氨酸修饰碳黑微电极的制备及多巴胺的测定

用电聚合法制备了聚L-组氨酸修饰碳黑微电极,研究了多巴胺在该修饰电极上的电化学行为。实验表明:该修饰电极对神经递质多巴胺的电化学氧化有显著的催化作用,采用二次导数线性扫描伏安法对多巴胺进行测定,在pH 7.0的磷酸盐缓冲溶液中,多巴胺在0.15 V处产生一灵敏的氧化峰,多巴胺的氧化峰电流与浓度在4.0×10-8~1.0×10-4mol/L范围内呈线性关系,检出限(3σ)为1.0×10-8mol/L。该聚合物修饰电极具有良好的选择性,能有效地排除抗坏血酸对测定的影响,用于人工合成样品的分析。     

聚精氨酸修饰玻碳电极上多巴胺的电化学特性及其检测

用循环伏安法制备了聚精氨酸修饰玻碳电极,研究了神经递质多巴胺在该聚合物薄膜修饰电极上的电化学行为及其检测。在pH7.0的磷酸盐缓冲溶液中,多巴胺在聚精氨酸修饰电极上于0.19V和0.16V处出现一对灵敏、可逆的氧化还原峰。在最佳测试条件下,氧化峰电流与多巴胺的浓度在3.0×10-7~8.0×10-4mol/L范围内呈良好的线性关系,线性回归方程为Ipa(μA)=86.063C(mmol/L) 20.183,相关系数r=0.9993,最低检测限(3σ)5.0×10-8mol/L。用于多巴胺针剂含量的测定,结果满意。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.